DIGITAL WIRELESS BACK-UP CAMERA
SYSTEM
DIGITALES KABELLOSES RÜCKFAHR-
KAMERA-SYSTEM
SYSTEME DE CAMERA DE RECUL SANS FIL
NUMERIQUE
DIGITALE DRAADLOOS CAMERASYSTEEM
with 12cm / 4.3” monitor mit 12cm / 4,3” Monitor avec écran 12cm / 4,3” met 12cm / 4,3” monitor
DRC4310
2
INTRODUCTION
a member of the family of advanced car back-up systems
|
|
International Ltd. |
|||
|
|
-up Camera and Monitor with built in transmitter box, when |
|||
|
|
|
your ability to see behind your car, camper, trailer, or |
||
|
|
numerous measures in quality control to ensure that your |
|||
|
|
|
and will perform to your satisfaction. |
||
P |
|
and follow the following safety and operating instructions. |
|||
|
|
|
INSTRUCTIONS |
||
If |
|
working with 12V/24V DC vehicle wiring, removing and |
|||
|
|
carpeting, dashboards or other components of your vehicle, |
|||
|
|
|
or consider having the camera system professionally |
||
|
|
interferences coming from Bluetooth, cell phones, Wi-FI routers, |
|||
|
|
|
electrical equipment. |
||
|
|
not be opened. Any attempt at modification or repair by the |
|||
|
|
your guarantee. |
|||
1. |
|
Arm |
2. Camera with mounting plate |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3. |
|
4. Monitor Power Cable |
|
|
|
|
|
|
|
|
|
|
|
|
|
5. |
|
cable |
|
|
|
|
|
|
INSTALLATION
These instructions do not apply to all vehicles. They are only meant as a general guide due to the number of different makes & models. For vehicle specific questions contact your vehicle’s manufacturer.
Camera installation
There are several ways to mount the camera on the back of your car. But the most convenient is to mount it near the license plate. Supplied is one mounting plate that can be fixed behind the license plate, and the mounting plate have been installed in the camera.
The camera itself is screwed on the mounting plate. The camera is tiltable, camera angle can be adjusted manually on vertical direction. Make sure that its field of view and detection are not obstructed.
With some type of cars it is not possible to mount the camera near the license plate. You may have to find another spot at the back of your car to mount it.
1. Remove the rear license plate, and then loosen the license plate bolts/screws.
2.Position the supplied mounting plates (with camera together) behind the license plate bracket. Secure both license plate bracket and mounting plates with the license plate bracket bolts/screws.
3. Mount the license plate on the license plate bracket.
4.Choose a routing path for the camera’s power cable through the vehicle’s body to the reverse light circuit. If in doubt, seek professional installation assistance.
5.Some vehicles may have a hole available to pass the wire through, such as where the license plate light is mounted, or you can drill a hole close to where the power cable is attached to the camera. Once you have chosen where the cable will enter the vehicle’s body, remove the camera. If you are able to use an existing opening, skip the next two steps.
6.Before you drill a hole you MUST CHECK and see WHAT IS BEHIND WHERE YOU ARE DRILLING. If there are any vehicle components, such as electrical parts or fuel system components behind where you are drilling, you must take whatever precaution is necessary not to damage them. Remove the license plate and camera before drilling.
7.After you have drilled the hole, insert the supplied grommet, then pass the camera cables through the grommet into the vehicle. You must use the grommet to prevent the metal edge of the hole from cutting the camera cable.
8.Next you’ll need to find the vehicle’s reverse lights. Turn the vehicle’s ignition key to the accessory position, engage the parking brake and put the car in reverse. Look at the vehicle’s tail lights to see where the reverse lights are located, they are the white lights. To locate the reverse light’s 12V/24V + wire it will be necessary to gain access to the rear of the vehicle’s tail light. For help locating the vehicle’s reverse light circuit contact your vehicle’s manufacturer for vehicle specific wiring diagrams.
9.Once you have located the reverse light circuit you will have to route the camera cable to that location. You must securely fasten the power cable to prevent it from being caught on any vehicle component such as the trunk hinge. Never route the cable on the outside of the vehicle!
10.The reverse light sockets on most vehicles have two wires connected to them. Usually the negative wire is black and the positive wire is a colored wire. If you are uncertain about the wiring, you can use a 12V/24V multimeter available at most auto parts stores to determine which is the positive wire. Follow the manufacturer’s instructions for the safe use of the multimeter.
11.After determining which wire is the positive and which is the negative, turn
off the ignition key, then remove the battery’s negative cable.
12.Splice the red wire using the supplied in-line wire connectors to the reverse light’s positive (+) wire. Use a set of slip joint pliers to squeeze the TAP and insure good connection.
13.Next splice the black wire of the camera power cable to the reverse light’s negative (-) wire or ground.
5
14.Replace the reverse light bulb, and then re-install the light socket. Secure all the wires with cable ties or electrical tape.
15.Re-attach the negative battery cable to the battery.
Monitor Installation
When choosing a location to mount the monitor, make sure the monitor is in an area that will not obstruct your vision while driving.
1.Before mounting the monitor, clean the mounting surface well.
2.Position the suction mount to the smooth surface which suits your requirement.
3.Press the suction cap against the smooth surface and press the lock down to attach and fix the mount to the surface.
Snap in the monitor to the suction mount.
4.Adjust the mounting arms to suit your view angle to the monitor and tighten the screws on the mount to fix the position.
5.Route the power cable to the vehicle’s cigarette lighter socket 12V/24V power outlet. The cable must not interfere with the safe operation of the vehicle.
6.Insert the small 12V/24V DC plug of the power cable into the right side of the monitor.
7.Plug the 12V/24V cigarette lighter plug into the vehicle’s cigarette lighter socket.
To maximize the effectiveness of the suction mount, it is recommended that the application be performed under the following conditions:
•Surface temperature should be between 21 and 38 degrees Celsius.
•Application below 10 degrees should be avoided.
•Application should not occur in direct sunlight.
Mounting should be protected from exposure to direct sunlight for a period of 24 hours.
NOTE: UNDER EXTREME BRIGHT LIGHT CONDITIONS, THE SCREEN IMAGE MAY TAKE A FEW SECONDS TO STABLIZE. PLEASE WAIT UNTIL THE IMAGE HAS STABLIZED BEFORE BACKING UP.
System testing
1.Reattach the vehicle’s negative battery cable.
2.Turn the ignition key to the accessory position, do not start the vehicle.
3.Engage the parking brake, and then put the shifter in the reverse position.
4.After testing the unit and you are satisfied with the route you have chosen for the cabling, you must permanently install it.
5.Route all wires behind interior panels or under carpeting so they are hidden. Use supplied cable ties to neatly gather any excess wire.
6
OPERATION
Please always pair the monitor and camera before the 1st operation, please refer to below “Pairing” step.
There are 5 control buttons available for users to have their controls:
Menu button
Arrow button
Power button
Arrow button
Guideline button
Power button
Press the POWER button to supply power to the monitor. The picture on the monitor will automatically turn on when the vehicle is in reverse gear (when already paired as described below). When the monitor gets an image, the blue LED will be lit. If there is power to the monitor, but the monitor does not get any image, the blue LED will blink on and off. When the monitor power is off, no picture can appear on the screen and the blue LED will be off.
Menu button
Press the Menu button to enter the menu screen as shown below: Picture SPEC, Picture Direction, Pair, Product Information.
In general please select the desired menu by pressing the arrow buttons
and confirm your choice with the Power Button..
Pairing:
Select the “Pair” icon with the arrow buttons and press the Power button. Shortly after please press the rubber button on the bottom of camera until the signal is well received by the monitor and “OK” appears on the screen. The unit will work properly and will automatically pair by itself in the future operation. Press the menu button to exit the selection or it will automatically exit after 30s.
7
Picture SPEC:
Please chose the menu “Picture Spec” with the arrow buttons and confirm with the Power Button. In this menu you can change brightness, contrast or colour of the picture.
Chose the desired function with the arrow buttons, confirm by pressing the Power button and change the values with the arrow buttons.
To save the settings and exit the screen please press the menu button.
Orientation:
In the Menu “Picture direction” you can change the orientation of the picture. These different views allow you to mount the camera and monitor in any position with keeping the right picture on the monitor. Simply enter the “Picture direction” menu by choosing it and pressing the Power button. The orientation of the picture will change every time pressing the Power button.
To save the settings and exit the screen please press the menu button.
Guideline button
This camera system has the option to show distanceguidelines on the display. This helps you to visually see the distance between the objects behind your car. By pressing the guideline button, you can switch this option on and off.
8
TECHNICAL SPECIFICATIONS
Camera |
|
Operating Voltage |
8-28V DC |
Current consumption |
<120mA(IRLED OFF); <170mA(IRLED ON); |
Image sensor |
CMOS |
No. of pixel |
640x480 |
Optical lens |
F1.7mm / F2.4 |
Transmission frequency |
2.4G (ISM band) |
RF transmission distance (open space) |
25M |
LCD monitor |
|
Operation Voltage |
8-28V DC |
Standby Current |
<50mA |
Operation Current |
<200mA |
LCD display screen size |
12cm / 4.3 inch |
No. of pixel |
480x272 |
Operation temperature |
-10 to +45 degree Celsius |
This model may be operated in EU countries.
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
WARRANTY
Pro-User warrants this product for a period of 2 years from the date of purchase to the original purchaser. Warranty is not transferable. Warranty covers defect against workmanship and materials only. To obtain warranty service, please return the unit to the place of purchase or authorized Pro-User dealer together with your proof of purchase. The warranty is void if the product has been damaged or not used as described in this manual. Warranty is void if a non-authorized repair has been performed. Pro-User makes no other warranty expressed or implied. Pro-User is only responsible for repair or replacement (at Pro-Users’ Discretion) of the defective product and is not responsible for any consequential damage or inconvenience caused by the defect.
9
gehört zur Familie der zukunftsweisenden Auto-Rückfahr- Pro-User-International Ltd.
-User Rückfahrkamera mit Monitor ermöglicht es Ihnen, hinter oder Mini-Van zu sehen. Es wurden zahlreiche Maßnahmen bei
um Ihnen ein hochwertiges Produkt zu Ihrer
.
sorgfältig durch und folgen Sie den Sicherheitshinweisen und der Montageanleitung.
fühlen, dieses System an die 12V/24V Stromversorgung Ihres zu montieren (bohren von Löchern, abnehmen von
Sie Kontakt zu Ihrem Autohaus oder zur Kfz-Werkstatt Ihres Sie eine professionelle Montage des Systems in Auftrag
wird dieses Kamera-System nicht von Handys, Bluetooth, Navigationssysteme und anderen
.
darf nicht geöffnet werden! Bei jeglichem Versuch einer
.
1. |
|
2. Kamera mit Befestigungsplatte |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3. |
|
4. Stromkabel für Monitor |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5. |
|
zur Störungsunterdrückung |
|
|
|
|
|
|
|
|
|
Loading...