Page 1
DK: Samlevejledning og sikkerheds anbefalinger
UK: Assembly instruction and safety regulations
Cykelholder/Bike carrier
AMBER IV DELUXE
Max. kugletryk
Max. ball pressure
Wægt cykelholder
Weight bike carrier
Max. last
Max. load
50kg
19,5kg
30,5kg
60kg
19,5kg
40,5kg
75kg
19,5kg
55,5kg
90kg
19,5kg
Max. 60kg
European permission
E4-26R-03 0281
Page 2
2
Page 3
3
INTRODUCTION
Pro-User AMBER IV cykelholder producers af Tradekar Benelux BV, Holland
Cykelholder til anhængertræksmontering
Passer til alle typer DIN-anhængertræk
Sikker og stabil, nem vippefunktion. Til transport af 4 cykler
Nem montering på bilens anhængertræk uden brug af løst værktøj
Vippefunktionen, gør det muligt at komme til bilens bagagerum selv med
cyklerne monteret
Cyklerne holdes I brede og stabile hjulholdere
Samt cykelstelgribere med blødt gummi-indlæg.
Fleksible arme passer til de fleste cykelstel
Elsæt med både 7-pol og 13-pol stik (Jaegers)
Inkl. Tågelygte og baklygte (virker kun med 13-pol stik)
Cykelholderen kan aflåses til bilens anhængertræk
Europa godkendelse givet af RDW
Page 4
4
VIGTIG INFORMATION
Læs instruksvejledningen grundigt igennem inden ibrugtagning.
Samling og montering af cykelholder må kun ske ud fra denne vejledning.
En fejlagtig samling og montering kan være katastrofal.
Cykelholderen er godkendt til transport af 4 cykler. Venligst tjek den maksimale
lastevne i tabellen nedenfor. Tjek også hvor stort et kugletryk bilens
anhængertræk er godkendt til. Se typeplade på anhængertrækket eller i bilens
instruktionsbog.
Den maksimale lastevne for cykelholderen er 60kg forudsat at bilen må laste
75kg på trækket. Cykelholderens vægt er 19,5kg.
Max. kugletryk
Vægt cykelholder
Max. last
50kg
19,5kg
30,5kg
60kg
19,5kg
40,5kg
75kg
19,5kg
55,5kg
90kg
19,5kg
Max. 60kg
Kan ikke anbefales til anhængertræk I aluminiumsudførsel.
Gem denne instruktionsvejledning i bilen.
Page 5
5
SAMLING AF CYKELHOLDEREN
Cykelholderen kommer usamlet. Tag alle dele ud af emballagen og arranger dem
på gulvet som vist nedenfor.
Step 1
Dele:
Montering:
Placer de 8 hjulholdere på bundrammen. Fastgør dem med de 16 bolte M6x50,
M6 planskiver og M6 møtrikker I bundrammen.
Saml de 2 lygter ved at sætte dem sammen og
fastgør dem med den medleverede skrue M5x12 og
planskiver.
Monter den nu samlede lygtebom på
bundrammen ved hjælp af de 2 M5x35 bolte
og planskiver.
Vær opmæsom på at tågelygten er i venstre side af cykelholderen!
Resultat:
Page 6
6
Step 2
Dele
Montering:
Monter den store U-bøjle på bundrammen. Benyt de
medfølgende bolte (M8x60), planskiver og de store plast
fingermøtrikker.
Vær opmærksom på at de 2 store fingermøtrikker sidder på
indvendig side (se foto).
Bemærk: Stram godt til, så u-bøjlen sidder urokkelig fast. Ubøjlen kan nedfældes fx ved opbevaring.
Resultat:
Page 7
7
Step 3
Dele:
Montering:
Løsne de små skruer hvor nummerpladerammen skal side. Monter denne derpå
på rammen. Nummerpladerammen skal være i samme højde som lygterne.
De medfølgende strips bruges til at føre og samle ledningerne. Trækkes frem til
venstre side af cykelholderen, idet bilens stikdåse sidder til venstre for trækket.
Vær opmærksom på at de ikke genere tiltfunktionen.
Før de 12 tekstilremme igennem hjulholderne og spænd
dem. Husk altid at spænde dem, også selvom cykler
ikke er på holderen, så du ikke rissikere at miste dem
under kørsel. ( Se foto )
Sluttelig monteres de 4 plastik beskyttere midt imellem hjulholderne på rammen.
Slut resultat:
Page 8
8
STELHOLDERNE
Page 9
9
Hængelås
Justerbar bolt
Låsemøtrik
Lås/sikkerhedsnål
Quick montering håndtag
MONTERING AF CYKELHOLDER PÅ ANHÆNGERTRÆK
Vi anbefaler at du bliver fortrolig med brugen heraf.
Quick monterings håndtag er formonteret på cykelholderen. Ved brug af denne
fastgøres nemt og hurtigt cykelholderen. Cykelholderen er solidt fastmonteret,
når håndtag står vandret og sidder urokkelig fra side til side og op og ned.
Når du monterer cykelholderen på bilen, er det bedst, at bilen er parkeret lige,
motoren er slukket, og parkeringsbremsen er aktiveret. Sørg for, at trækkuglen
er ubeskadiget, ren og ikke fedtet!
Af montering:
Lås/sikkerhedsnål trækkes ud og dreje den med en kvart omdrejning. Derpå kan
håndtaget trækkes op i lodret position og cykelholderen kan tages af trækket.
Montering:
Placer cykelholderen henover trækkuglen. Tryk håndtaget nedad (ca. 35-40 kg),
indtil det stopper (håndtaget forbliver stabilt i vandret position). Drej lås /
sikkerhedsnål, indtil denne er fastgjort (og håndtaget kan ikke længere trækkes
op).
Page 10
10
Låsemøtrik
Justerbar bolt
Test nu, om cykelholderen er fastgjort stabilt nok på trækkuglen (og ikke let at
vride). Hvis ikke, skal du justere på justerbolten i siden. Hvis den ikke er stram
nok, tag cykelholderen af igen og skru ind i justeringsskruen på hurtigkobleren.
Juster ind indtil cykelholderen sidder urokkelig fast.
Caution: Vær opmærksom på at justerbolten er
låst med låsemøtrikken!
Cykelholderen kan aflåses med den medfølgende
hængelås. Opbevar nøglerne på et forsvarligt sted,
Afstem altid om justerbolt er forsvarligt fastspændt og at
sikkerhedsnålen sidder korrekt ind kørsel foretages.
Vi anbefaler at overholde gældende tilladte hastigheder.
Page 11
11
TILTFUNKTION
For nem adgang til bilens bagagerum har vi udstyret cykelholderen med en
tiltfunktion.
Først laser du op på tilt-funktionshåndtaget: Press en finger på den bageste knap
(1), derpå træk håndtaget frem (2) væk fra dig.
Med en hand på cyklerne eller U-bøjlen
og den anden på tilt-funktion-håndtaget,
som du trækker op imod lodret for at låse
funktionen op. (3). Vip forsigt holderen
bagud.
Pas på dit hoved!
Modsat for at få cykelholderen
tilbage I køreposition. Lyt efter et
klik.
Sikrer dig aldrig at
tilfunktions-håndtaget er
aflåst, inden kørsel
påbegyndes.
3
1
2
Page 12
12
BELYSNING
Denne cykelholder er udstyret med lygter. Systemet kan forbindels med bilens
strømsystem med adapter. Bemærk der findes både såkaldt 7-pol stik samt 13pol stik. Begge adaptere medfølger denne
cykelholder.
Afdæk det stik som ikke anvendes med
beskyttelsescover.
Universal system 7 pin
1/L
2/54G
3/31
4/R
5/58R
6/54
7/58L
Indicator left
Rear fog light
Ground
Indicator right
Rear light right
Stop lights
Rear light left
The reversing light is not
working via the 7-pin plug!
yellow
blue
white
green
brown
red
black
Jaegers system 13 pin
(DIN 72.570)
1
2
3
4
5
6
7
8
9
10
11
12
13
Indicator left
Rear fog light
Ground
Indicator right
Rear light right
Stop lights
Rear light left
Reversing light
Not used
Not used
Not used
Ground
Not used
yellow
blue
white
green
brown
red
black
grey
Page 13
13
MONTERING AF CYKLER PÅ CYKELHOLDEREN
Fjern alle løse dele på cyklen (pumper, speedometer, kurve,
drikkedunke, elcykel-batterier) under transport. Disse dele kan
ryste sig løse og være til fare for medtrafikanter.
Den tungeste cykel (max 15kg) monteres tættest på bilen og fastgøres med
stelholder og hjulholdere
Stelholderne er fleksible og justerbare. Kan trækkes rundt på U-bøjlen og
monteres på sadelstang eller ’herrestang’ på cyklen. Vi anbefaler så høj
montering som muligt for bedst stabilitet.
Cykelhjulene fastgøres med de medfølgende
tekstilremme. 1 til baghjul og 2 til forhjulet.
(se foto).
Cyklerne monteres modsat af hinanden således styr går fri.
Sikrer dig at anvende den ekstra sele omkring alle cykler og
omkring U-bøjlen. Dette er en dobbelt sikkerhed.
Brug af sikkerhedsrem
Vi anbefaler at anvende den medfølgende sikkerhedsrem ved transport af 4
cykler. Se tegning herunder for montering og føring af rem.
Pas på om bilen har en spoiler monteret.
1
2
3
Page 14
14
SIKKERHEDS-ANBEFALINGER
Sørg for at trækkuglen er ren og affedtet.
Efter anvendelse de første par gang bør du efterjuster forankringen, som går ned
over bilens trækkugle. Hold løbende øje med dette!
Check cykelholderen for eventuelle fejl inden kørsel påbegyndes. Defekte dele
bør omgående udskiftes med originale dele.
Modificer under ingen omstændigheder på cykelholderen, og saml den efter vore
instruktioner. Det kan være livsfarligt om ikke den samles korrekt. Vi yder ingen
garanti, såfremt vejledningen ikke er fulgt, og kan ikke holdes ansvarlige for
eventuelle uheld.
Altid sikrer dig at cyklerne er forsvarligt fastgjort til cykelholderen med alle
medfælgende remme og stelholdere.
Sikrer dig at cykelholderens tilt-funktion er i låst-position.
Sikrer dig at anvende den ekstra sele omkring alle cykler og omkring U-bøjlen.
Dette er en dobbelt sikkerhed.
Vær opmærksom på at alle løse dele på cykler er afmonteret INDEN KØRSEL
FORETAGES (sadeltasker, pumper, skærme etc)
Check lejlighedsvis alt fungere som det skal og møtrikker og bolte er solidt
spændt sammen. Efterspænd om nødvendigt.
Sikrer dig at låsen ned over bilens træk er forsvarligt aflåst.
Anbring ikke et cover omkring cyklerne under kørsel.
Kørsel med cykelholder ændrer bilens køreegenskaber radikalt.
Vi anbefaler at overholde gældende hastigheder og maks
120km/t). Kør med ekstra god afstand. Undgå
kraftige opbremsninger.
Husk at når du bakker med bilen at du hare n
cykelholder monteret!
I tillæg vær opmærksom på eventuelle gældende landekrav for
transport af gods bag på bilen.
Hvis bilen er udstyret med en automatisk åbning af bagklap, slå dette fra, når du
kører med cykelholderen.
Afmonter cykelholderen før bilvaske-anlæg
Cykelholderen er ikke til “off road” anvendelse
Page 15
15
VEDLIGEHOLD
Opbevar altid cykelholderen ren og tørt sted efter brug. Sprøjt evt. med
vandslangen for at fjerne mudder og andre beskidte ting.
Hold bilens trækkugle ren og fri for fedt.
Kontroller cykelbæreren regelmæssigt, hvis der er nogen skade. Skadede eller
brugte dele skal udskiftes med det samme. Brug kun originale reservedele.
Cykelholderens møtrikker og bolte skal kontrolleres regelmæssigt, og om
nødvendigt stramme dem igen.
Hvis der er en skade på cykelbærerens pulverlakering, skal dette straks
behandles med maling.
Roterende og bevægelige dele skal smøres med olie regelmæssigt.
GARANTI
Dette produkt er dækket af en 2 års garanti. Vær opmærksom på, at vores
garanti dækker en rimelig brug af cykelbæreren, det dækker IKKE nogen skade
forårsaget af misbrug. Dette gælder også for en fejl eller fejl i cykelbæreren, der
er forårsaget af dårlig eller ukorrekt installation. For at sikre garantiens
gyldighed bedes du udføre vedligeholdelse i overensstemmelse med
vedligeholdelsesafsnittet. Vi forbeholder os ret til at foretage et opkald og / eller
reparationsafgift for ethvert arbejde, der kræves for at afhjælpe fejl, som er
uden for virksomhedens kontrol, dvs. ukorrekt eller dårlig tilpasning, misbrug,
utilsigtet skade mv.
Page 16
16
INTRODUCTION
The Pro-User AMBER IV bike carrier is part of the family of bike carriers
manufactured by Tradekar Benelux BV
Hitch ball bike carrier
Suitable for almost all types of hitch balls, bikes and wheel dimensions
Safe and reliable, easy to tilt bike carrier for the transport of 4 bicycles
Extremely simple and quick fitting on the tow-ball via the quick connector
The trunk of your car is always accessible by the easy to use tilting system
Bikes are held in wide, stable wheel holders
Fixing of the bicycles on the frame, so no force on the pedals of your bike
Flexible bike holding arms
Lighting via a 7 and 13 pin (Jaeger) plug
Including fog light and reverse driving lighting (only working via the 13-pin
plug)
The carrier can be locked to the tow ball
European permission given by the RDW
Read the following safety- and operating instructions
carefully and act accordingly before using the bike
carrier.
Page 17
17
IMPORTANT INFORMATION
Read these instructions carefully before using the product for the first time.
Do not use this product until the manual and safety regulations are read and are
entirely clear.
The assembly and installation of the bike carrier can only be done according this
instruction manual.
The steps that are mentioned and the safety regulations for assembly, handling
and use of the bike carrier need to be followed! The slightest non conformity can
lead to incorrect assembly or wrong use.
The carrier is suitable for the transport of four bikes at most. Please check the
maximum permissible ball load. You can find it on the identification plate of the
hitch ball of your car (for most cars this is 75kg). The total weight of the carrier
with the bikes cannot exceed the maximum permissible ball load of the hitch ball.
The maximum permissible load for the carrier itself may be 60kg.
The net weight of the carrier is 19,5kg.
Max. permissible Ball
load
Weight bike carrier
Max. load
50kg
19,5kg
30,5kg
60kg
19,5kg
40,5kg
75kg
19,5kg
55,5kg
90kg
19,5kg
Max. 60kg
Not suitable for the use on an aluminium hitch ball.
Keep these instructions in your car.
Page 18
18
MOUNTING THE BIKE CARRIER
The bike carrier comes unassembled. Remove all parts from packaging and
arrange them in a well-organized way. The instructions will clearly describe and
show the parts that you need for each step and how to assemble the bike carrier.
Step 1
Parts:
Mounting:
Put the eight wheel holders on the base frame of the bike carrier with the holes
right above the holes in the base frame. Then attach the wheel holders with the
sixteen bolts M6x50, washers M6 and M6 nuts.
Mount the two lamp holders together. This is done by
means of a small piece of iron connection that is
already pre-mounted on one side. Slide the rails
“together” and fix it by the supplied screw (M5x12)
and washers.
Mount the lamp holder rail at the bottom of
the base frame with the two M5x35 bolts and
washers.
Make sure that the rear fog lamp is mounted on the left side of the bike carrier!
End result:
Page 19
19
Step 2
Parts
Mounting:
Slide the U-frame against the outside of the U-frame holders of the
base frame. Secure this U-frame with the supplied carriage bolts
(M8x60), washers and plastic rotary knobs.
Make sure the plastic rotary knobs are on the inside (see picture).
Please note: firmly tighten both rotary knobs so that the U-frame
will come on its place well.
End result:
Page 20
20
Step 3
Parts:
Mounting:
Loosen and remove the little screws intended for the mounting of the number
plate holder from the light holder rail and fasten the number plate holder to the
rail. The number plate holder has to be level with the lighting.
With the cable ties supplied with the carrier, the light cable can be fastened
neatly at the bottom of the carrier. Make sure the cable will not interfere with the
tilting mechanism.
Slide the twelve short, black straps through the little
slots in the wheel holder, starting inside-out, going
around the wheel holder and then outside-in (see
picture).
Finally clip the four plastic covers over the middle of the
four wheel holders.
End result:
Page 21
21
LOCKABLE FRAMEHOLDERS
Page 22
22
Padlock
Quick connector adjustment screw
Locking nut
Locking/safety pin
Quick connector handle
MOUNTING OF THE BIKE CARRIER ONTO THE HITCH BALL
The first step is to become familiar with the quick connector.
The quick connector consists of a case mounted to the bike carrier and a lever.
Using the lever, you can close and open the quick connector.
When mounting the bike carrier to the car, it is best that the car is parked
straight, the engine is turned off and the parking brake is activated. Make sure
that the tow ball is undamaged, clean and not greasy!
Release the locking/safety pin by pulling it out and rotating it by a quarter turn.
Release the quick connector by moving the handle in the vertical position.
Position the bike carrier on the tow bal from the top. Press the handle of the
quick connector downwards (approx. 35-40kg) until it stops (handle will stay
stable in the horizontal position). Turn the locking/safety pin until it is secured
(and the handle can no longer be pulled up).
Now test if the carrier is attached steady enough on the tow ball (and not easy to
twist). If not, you have to adjust the quick connector. If it is not tight enough,
take the carrier off again and screw in the adjustment screw of the quick coupler
Page 23
23
Locking nut
Adjustment screw
a little bit further. Loosen locking nut first, screw in adjustment screw and
tighten locking nut again.
Check again if the carrier is properly secured to the
tow ball (and cannot rotate easily). Repeat this until
the carrier is properly secured.
Caution: Always make sure that the locking nut
of the adjustment bolt is tightened again!
When the bike carrier is not easy to turn anymore, the
quick connector can be locked. Lock the quick
connector with the locking/safety pin and the padlock
and take the key out. Keep it carefully on a safe place.
The bike carrier is now also protected against theft.
Always check if the quick connector is well secured with the
locking/safety pin and the padlock!
Page 24
24
TILTING MECHANISM
For easy access to your boot, even if the bikes are mounted on the carrier, you
may use the tilting mechanism.
First unlock the lock of the tilting-mechanism handle: Press your finger into the
rear button (1), then slide the handle (2) horizontally backwards (away from
you).
With one hand, keep a firm grip on the Uframe or bikes so that the carrier cannot
fall down in an uncontrolled movement.
With the other hand, pull the handle of
the tilting mechanism up to unlock it (3).
It is now possible to tilt the carrier.
By pushing the entire carrier up,
the tilting mechanism is locked
again (you hear a click). Make
sure to always secure the handle
again by sliding this to the
locking position.
The bike carrier may never be used if the tilting mechanism
is not well secured.
3
1
2
Page 25
25
LIGHTING
This bike carrier is equipped with a lighting system. This system can be
connected to the hitch ball power socket of your car. Seeing that there are
different kinds of sockets that require different
kinds of plugs, this carrier comes with the
usual 7-pin plug and the 13-pin plug (Jaeger).
As a result, the carrier can be used with any
hitch ball!
Both plugs are in one housing. Please cover
the plug you don’t use with the supplied cover.
Universal system 7 pin
1/L
2/54G
3/31
4/R
5/58R
6/54
7/58L
Indicator left
Rear fog light
Ground
Indicator right
Rear light right
Stop lights
Rear light left
The reversing light is not
working via the 7-pin plug!
yellow
blue
white
green
brown
red
black
Jaeger system 13 pin
(DIN 72.570)
1
2
3
4
5
6
7
8
9
10
11
12
13
Indicator left
Rear fog light
Ground
Indicator right
Rear light right
Stop lights
Rear light left
Reversing light
Not used
Not used
Not used
Ground
Not used
yellow
blue
white
green
brown
red
black
grey
Page 26
26
MOUNTING OF THE BIKES ON THE BIKE CARRIER
Remove all parts from the bikes that could easily be lost (E-bike
batteries, bike pumps, speedometers, baskets, panniers, bicycle
seats etc.) during transport. These parts may become loose by
the increased air resistance and vibration and put other road users at
risk.
The first (and heaviest, max 20kg) bike has to be placed in the rear wheel holder
(the one which is the nearest to the car) and secured with the short frame holder
on the U-tube.
The frame holders are flexible to place on the U-tube, and are also flexible to
place on your bike. Try the first time which position in your situation works best
(and most stable affirmative is). It is important to place the frame holder as high
as possible, giving maximum stability.
Secure the wheels using the supplied short
straps. One strap for the fixation of the rear
wheel and two straps for the front wheel (see
picture).
Place every next bike in opposite directions into the other wheel holders and
proceed as described above for the first bike.
Now secure the bikes using the long safety
belt. Run the safety belt through the bike frame
and around the U frame and tighten firmly.
Page 27
27
Use of strain relief strap
Before mounting the strain relief strap remove dust and dirt from the top of the
trunk of your vehicle. Open the trunk of your vehicle. Run the free end of the
strap between the trunk door and roof edge outwards (1). Leave about 20cm
free between the anchor and the roof edge. Close the trunk of your vehicle
gently. Make sure the strap is flat and straight between the seals. Now slowly
pull the strap out until the anchor is stopped by the roof edge and the trunk of
your vehicle.
Make sure that any existing roof spoiler is not damaged and that the function of
strain relief strap is not affected by the roof spoiler.
Attach the part of the belt with the buckle on the U-tube of the bike carrier (2).
Connect the two parts of the strain relief strap to each other (3) and pull the
strap tight.
SAFETY REGULATIONS
Keep the tow ball clean and free of grease.
Each time after having mounted the carrier on the tow ball, it will "settle" during
the first kilometres that you drive. Therefore, check if the carrier is still firmly
secured after the first few kilometres and if necessary, tighten the locking bolt.
Check the bike carrier before use if there is any damage. Damaged or worn parts
need to be replaced immediately. Only use original replacement parts.
Do not make any modifications on the bike carrier (mechanical or electronic)
This can be very dangerous. Warranty claims will not be accepted and we cannot
guarantee the correct functionality of the bike carrier, if you done modifications.
We are not responsible for damage caused as result of incorrect assembly,
installation or modification.
Check the correct operation of the lighting at regularly.
Always make sure that the bikes are firmly fixed by using the frame holders and
wheel safety belts.
Always use the extra safety belt, for extra protection of your bikes. Run the
safety belt trough the U-frame and the frames of the bikes, and pull this firmly.
1 2 3
Page 28
28
Always use the additional strain relief strap. Connecting strap between U-tube of
the bike carrier and the tailgate upper edge: To reduce the rocking of the bike
carrier on uneven roads.
Make sure that no parts of the bike can get lost during driving (E-bike batteries,
pump, basket, child seat, saddlebag, bicycle bag, etc.). Always remove these
before driving!
Check regularly if all the belts, knobs and fixations are firmly secured and if
necessary secure them again.
Always make sure that the tilting mechanism is locked.
Always make sure that the quick connector is closed and locked.
Do not cover the bikes with a cover while driving.
Driving with a bike carrier affects the performance of your car.
Adjust your speed accordingly (max. 120km/h). Try to avoid
sudden braking and steering movements.
Please remember when driving in reverse that the
car is longer than usual!
In addition, pay attention to the regulatory requirements
applicable to the transport of goods at the back of your vehicle.
When you have a vehicle with electronic parking sensors, an error message can
come when the bike carrier is mounted. Switch off the parking system during the
use of the bike carrier.
If the car is equipped with an automatic opening of the trunk, this must be
switched off or only opened manually, if the bike carrier is mounted.
Take the bike carrier of the tow ball before using the carwash.
The bike carrier is not suitable for “off road” use.
Take the bike carrier of the tow ball if not used.
In case of defects or problems please contact your Pro-User supplier.
Page 29
29
MAINTENANCE
Always store the bike carrier clean and dry after use. If necessary spray with the
water hose to remove mud and other filthy stuff.
Keep the tow ball of the car clean and free of grease.
Keep the quick connector of the bike carrier clean and free of grease.
Check the bike carrier regular if there is any damage. Damaged or worn parts
need to be replaced immediately. Use only original replacement parts.
The nuts and bolts of the bike carrier need to be checked regular, if necessary
tighten them again.
If there is a damage on the powder coating of the bike carrier this needs to be
treated with paint immediately.
Rotating and moving parts need to be oiled regularly.
GUARANTEE
This product is covered by a 2 year guarantee. Please note that our guarantee
covers reasonable use of the bike carrier, and only applicable for parts. It does
NOT cover any damage caused by misuse. This also applies to a malfunction or
failure of the bike carrier that has been caused by poor or incorrect installation.
To ensure the validity of the guarantee please carry out maintenance in
accordance with the maintenance section. We reserve the right to make a call
out and/or repair charge for any work required to be undertaken to rectify faults
that are outside of the company’s control i.e. incorrect or poor fitting, misuse,
accidental damage, etc.
Page 30
30
PARTS LIST
Pos
nr.
Description
QTY
Remark
1
Main frame with quick connector
1
2
U-tube
1
3
Short frame holder
2 4
Long frame holder
1 5
Short frame holder “frame-frame”
1 6
Wheel holder
8
7
Strap
12
8
Plastic end-cap
2
19x19
9
Lamp holder tube left
1
10
Plastic protectioncover
2 11
Rearlights (set)
1 12
Plastic washer
4 13
Washer
4
M5
14
Spring washer
4
M5
15
Self-locking nut
4
M5
16
Screw
2
17
License plate holder
1 18
Plastic end-cap
2
25x30
19
Washer
1 20
Cross head bolt
2
M5x35
21
Self-locking nut
16
M6
22
Washer
16
M6
23
Carriage bolt
16
M6x50
24
Plastic cover
4 25
Plastic knob
2
M8
26
Washer
2
M8
27
Carriage bolt
2
M8x60
28
Plastic end-cap
4
25x60
Page 31
31
EXPLODED VIEW
Page 32
32
© Tradekar 91733DK/18A
Tradekar Benelux BV
Staalweg 8 +31 (0)345-470990
4104 AT CULEMBORG info@tradekar.com
The Netherlands www.pro-user.eu
Loading...