S C 1 5 P R I S M A S Y S T E M C O N T R O L C E N T E R
User Guide
SC15 Prisma System Control Center User Guide2
CAUTION
TO REDUCE THE RISK OF FIRE, REPLACE WITH THE
SAME TYPE AND RATING OF FUSE.
ATTENTION
UTILISER UN FUSIBLE DE RECHANGE MÊME TYPE.
Safety compliance
This product has been designed to meet the IEC 60065
international electrical safety standard.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
The lightning flash with an arrowhead symbol within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated 'dangerous voltage' within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.
CAUTION: To reduce the risk of electrical shock do not
remove cover (or back). No user serviceable parts inside.
Refer servicing to qualified service personnel.
W
ARNING: To reduce the risk of fire or electrical shock,
do not expose this apparatus to rain or moisture.
CAU
TION: In Canada and the USA, to prevent electric
shock, match the wide blade of the plug to the wide slot
in the socket and insert the plug fully into the socket.
This product is designed and manufactured to meet strict
quality and safety standards. However, you should be aware
of the following installation and operation precautions.
1. Take heed of warnings & instructions
You should read all the safety and operating instructions
before operating this appliance. Retain this handbook
for future reference and adhere to all warnings in the
handbook or on the appliance.
2. Water and moisture
The presence of electricity near water can be dangerous.
Do not use the appliance near water – for example next to
a bathtub, washbowl, kitchen sink, in a wet basement or
near a swimming pool, etc.
3. Object or liquid entry
Take care that objects do not fall and liquids are not spilled
into the enclosure through any openings. Liquid-filled objects
such as vases should not be placed on the equipment.
4. Ventilation
Do not place the equipment on a bed, sofa, rug or similar
soft surface, or in an enclosed bookcase or cabinet, since
ventilation may be impeded. We recommend a minimum
distance of 50mm around the sides and top of the
appliance to provide adequate ventilation.
5. Heat
Locate the appliance away from naked flames or heat
producing equipment such as radiators, stoves or other
appliances (including other amplifiers) that produce heat.
6. Climate
The appliance has been designed for use in moderate
climates.
7. Racks and stands
Only use a rack or stand that is recommended for use with
audio equipment. If the equipment is on a portable rack it
should be moved with great care, to avoid overturning the
combination.
8. Cleaning
Unplug the unit from the mains supply before cleaning.
The case should normally only require a wipe with a soft,
damp, lint-free cloth. Do not use paint thinners or other
chemical solvents for cleaning.
We do not advise the use of furniture cleaning sprays or
polishes as they can cause indelible white marks if the unit
is subsequently wiped with a damp cloth.
9. Power sources
This appliance must be connected to a mains socket
outlet using the supplied power cord. To disconnect
this apparatus from power, you must disconnect the
power cord. Make sure the power cord is always easily
accessible.
Only connect the appliance to a power supply of the type
described in the operating instructions or as marked on
the appliance.
This is a Class 1 device and must be earthed.
The power switch is a single-pole switch. When the switch
is in the “Off” position, the appliance is not completely
disconnected from the main power.
10. Power-cord protection
Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon
or against them, paying particular attention to cords and
plugs, and the point where they exit from the appliance.
11. Grounding
Ensure that the grounding means of the appliance is not
defeated.
12. Power lines
Locate any outdoor antenna/aerial away from power lines.
13. Non-use periods
If the unit has a stand-by function, a small amount of
current will continue to flow into the equipment in this
mode. Unplug the power cord of the appliance from the
outlet if left unused for a long period of time.
14. Abnormal smell
If an abnormal smell or smoke is detected from the
appliance, turn the power off immediately and unplug the
unit from the wall outlet. Contact your dealer immediately.
15. Servicing
You should not attempt to service the appliance beyond
that described in this handbook. All other servicing should
be referred to qualified service personnel.
16. Damage requiring service
The appliance should be serviced by qualified service
personnel when:
A
. the power-supply cord or the plug has been damaged, or
B. objects have fallen, or liquid has spilled into the
appliance, or
C.
the appliance has been exposed to rain, or
D. the appliance does not appear to operate normally or
exhibits a marked change in performance, or
E.
the appliance has been dropped or the enclosure
damaged.
SC15 Prisma System Control Center User Guide 3
2.4G and 5G FCC Statements
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1.
This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Cet appareil est conforme à la section 15 des
réglementations de la FCC. Le fonctionnement de
l’appareil est sujetaux deux conditions suivantes :
1.
cet appareil ne doit pas provoquer d’interférences
néfastes, et
2
. cet appareil doit tolérer les interférences reçues,
y compris celles qui risquent de provoquer un
fonctionnement indésirable.
N
ote: This product has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This product generates, uses, and
can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this product does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
•
Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
•
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV
technician for help.
Please take attention that changes or modification
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
This equipment should be installed and operated with a
minimum distance
20cm between the radiator and your
body .
Cet équipement doit être installé et utilisé à une distance
minimale de
20 cm entre le radiateur et votre corps.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1.
this device may not cause interference, and
2. this device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radioexempts de
licence. L’exploitation est autorisée aux deux conditions
suivantes :
1.
l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter
may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d’Industrie Canada,
le présent émetteur radio peut fonctionner avec une
antenne d’un type et d’un gain maximal (ou inférieur)
approuvé pour l’émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radioélectrique
à l’intention des autres utilisateurs, il faut choisir le type
d’antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité
nécessaire à l’établissement d’une communication
satisfaisante.
The CE symbol indicates that this Primare product
complies with the EMC (Electromagnetic Compatibility)
and LVD (Low Voltage Directive) standards of the
European Community.
The WEEE symbol indicates this Primare product complies
with the European Parliament and Council Directive
2
002/96/EC concerning Waste Electrical and Electronic
Equipment (WEEE). This product must be appropriately
recycled or processed in accordance with these directives.
Consult your local waste disposal authority for guidance.
The RoHS symbol indicates that Primare products are
designed and manufactured to comply with the Restriction
of Hazardous Substances (RoHS) as stated in the European
P
arliament and Council Directive 2002/95/EC.
Copyright and acknowledgments
Copyright © 2017 Primare AB.
All rights reserved.
Primare AB
Limstensgatan 7
2
1616 Limhamn
Sweden
http://www.primare.net
Issue: SC15Prisma/1
The information in this guide is believed to be correct as
of the date of publication. However, our policy is one of
continuous development and so the information is subject
to change without notice, and does not represent a
commitment on the par
t of Primare AB.
Primare is a trademark of Primare AB.
This guide was produced by
Human-Computer Interface Ltd.
http://www.interface.co.uk
SC15 Prisma System Control Center User Guide4
SC15 Prisma System Control Center User Guide 5
CONTENTS
Welcome! 6
Getting Started 7
1 Unpack the SC15 7
2 Pair the SC15 with speakers 7
3 Connect inputs 7
4 Connect the antennae 7
5 Connect power 7
6 Connect to Wi-Fi 7
Back-panel connections 8
Using the remote control 9
Selecting SC15 mode 9
Fitting the batteries 9
Using the SC15 10
Front panel controls 10
Changing the volume 10
Selecting a source 10
Changing the display brightness 10
Connecting direct sources 11
Playing music from a drive or music server 12
Streaming music from a phone, tablet, or PC 13
Configuring the settings 14
Using the settings menus 14
INPUT SETTINGS 14
AUDIO SETTINGS 15
GENERAL SETTINGS 15
STREAMING SETTINGS 16
NETWORK SETTINGS 16
Technical specification 17
Analogue inputs 17
Analogue outputs 17
Digital inputs 17
Digital outputs 17
Performance 17
Network 17
General 17
Additional information 18
Phase 18
Burn-in 18
RS232 and trigger 18
Using the SC15 with a DD15 18
Error messages 18
Factory reset 18
Network troubleshooting 18
Index 19
SC15 Prisma System Control Center User Guide6
WELCOME!
Congratulations on selecting your new
SC15 Prisma System Control Center
This user guide describes the features and explains how
to set up the control center for the best sound quality and
ease of operation in order to allow for the most enjoyable
reproduction of sound from all your sources.
For additional support and assistance please contact your
local authorized Primare dealer, or visit our website at
www.primare.net.
SC15 Prisma System Control Center User Guide 7
GETTING STARTED
1 Unpack the SC15
Your SC15 is supplied with:
This User Guide
The Chromecast built-in Quick Start Guide
Mains cable
IR cable
Trigger cable
Antennas for Bluetooth and Wi-Fi
C
25 remote control with batteries
AC Polarity Pen
If any of these items are missing please contact your
supplier. We recommend you retain the packaging in
case you need to transport the unit at a later date.
Note that the SCI5 is supplied with a protective film on the
display glass. Remove the film for a clearer whiter display.
2 Pair the SC15 with speakers
The SC15 is designed to pair with WiSA loudspeakers,
using the using the Speaker Pairing System (SPS).
Press the SPS button on the back panel to put the SC15
into pairing mode.
Press the pairing button on the WiSA speakers to pair
the speakers with the SC15.
Analogue outputs
The SC15 provides a fixed-level or variable-level
analogue output on the ANALOG OUT output on RCA
connectors, to allow you to connect to active speakers or
an analogue recorder.
Digital outputs
The SC15 also provides a coax digital output on an RCA
connector.
l
l
l
l
l
l
l
l
l
l
3 Connect inputs
You can connect up to two analogue sources and up to
four digital sources to the inputs on the back panel.
Analogue sources
Connect an analogue source to A1, using a high
quality RCA cable.
A second analogue source can be connected to D6,
using a cable ter
minated in a 3.5mm jack plug.
Digital sources
Connect digital optical sources to the digital optical
inputs D2 to D4 using optical cables. D6 can be used
for an additional optical source.
Connect a digital coax source to D5, using a digital
RCA cable.
You can also connect a USB flash drive to the USB-A
input, and a PC or Mac to the USB-B input to use the
SC15 as an audio output device for your computer. For
more information see
PLAYING MUSIC FROM A DRIVE
OR MUSIC SERVER
, page 12.
Streaming
You can stream music wirelessly to the SC15 from a
mobile phone, tablet, computer, or other Prisma product
via Bluetooth or Wi-Fi, or via a wired Ethernet connection.
For more information see
STREAMING MUSIC FROM A
PHONE, TABLET, OR PC
, page 13.
4 Connect the antennae
Connect the two antennae supplied with the SC15 to
the ANT 1 and ANT 2 sockets on the back panel, and
position the two antennae at a slight angle from the
vertical.
One antenna is for Bluetooth connectivity, and the other
one is for Wi-Fi connectivity.
l
l
l
l
l
5 Connect power
Plug one end of the mains cable supplied with the
SC15 into the power connector on the back panel,
and connect the other end to a wall socket.
If this cable is not suitable for your power outlets please
contact your supplier for an alternative cable.
N
ote: See
Phase
, page 18, for information about getting
the best sound from your SC15.
WARNING: Always disconnect the SC15 from the
mains power before connecting or disconnecting
any cables.
Switch on the SC15, using the switch on the back panel.
To switch on from standby
Press O on the front panel or remote control.
The display shows:
PRIMARE
6 Connect to Wi-Fi
When the SC15 is ready to set up the network the display
will show Setup mode.
Make sure Bluetooth and Wi-Fi are enabled on your
mobile device.
Install the free Google Home app on your mobile device.
Run Google Home.
It will display N
ew device found, SC15.
Click SET UP and follow the instructions.
After playing a test sound you will be prompted to
connect to your home Wi-Fi network.
Select your Wi-Fi network and enter the password.
You will now be able to stream music to your SC15.
l
l
l
l
l
l
l
l
Loading...