Before allowing users on Precor equipment, review the Important
Safety Instructions found at the beginning of this manual. You
should also teach your patrons how to safely use the equipment
following the guidelines in Educating Users.
Entering the Safety Code
When the equipment is shipped from the factory, the safety code
protection feature is disabled.If you wish to enable the safety code,
refer to Club Features. Inform users that the equipment requests a
safety code to help prevent unauthorized use. When users select a
program or press QUICKSTART at the PRECOR banner, the
following prompt appears:
ENTER SAFETY CODE TO UNLOCK MACHINE
Users have two minutes to press the following number key
sequence and continue their workout: 1, 2, 3, 4.
Important: Tell users to hold onto the handrail with one hand
before entering the safety code with the other hand.
If the correct keys are pressed, the program selection process
begins. If the code is incorrect, the display prompts the user to
reenter the code after a 2-minute time out.
Note: On the treadmill, a 3-second countdown appears on the
display, and then the running belt starts moving. Refer to Workout
Options in the User’s Reference Manual.
Using the Safety Clip
Instruct users how important it is to use the safety clip while
exercising on the treadmill. Instruct them on how to attach it to their
clothing near their waistline. If any complications occur, a strong
tug on the safety lanyard will stop the running belt.
If the safety switch trips while users are exercising, have them
reattach the safety clip, press the SPEED up key or QUICKSTART
and reenter the safety code, if necessary.
Note: The treadmill retains users’ workout statistics if they resume
their workout within the limit set for pause mode.
Safety Clip
Lanyard
Figure 3: Attaching the safety clip
Product Owner's Manual: Treadmill Safety Features 8
Product Owner's Manual: Treadmill Safety Features 9
Turning the Treadmill On and Off
To turn the treadmill On and Off, use the power switch located
beneath the hood, near the power cord receptacle.
Important: When it is not being used, turn the treadmill Off.
Weight Limit
You should not allow runners over 350 lb. (160 kg) or walkers
heavier than 500 lb. (225 kg) on the treadmill.
Location
It is important to keep the area around the treadmill open and free
from encumbrances such as other equipment. The minimum space
requirement needed for user safety and proper maintenance is
three feet wide by six feet deep (one meter wide by two meters
deep), directly behind the running belt.
Self-Powered Features
On self-powered equipment, the battery initializes and displays the
Precor banner when a user starts exercising. A minimum rate of
motion must be maintained for the banner to appear, as shown in
the following table. When a person meets the requirements, the
power that is generated allows the equipment to function properly.
Table 1. Minimum requirements for operation
Equipment Rate of Motion
AMT 56 strides per minute (SPM)
EFX 40 strides per minute (SPM)
Climber 30 steps per minute
Cycle 20 revolutions per minute (RPM)
Informational displays appear when the battery is low or when the
rate of motion drops below the minimum requirements. The display
explains what to do to retain power. If the messages are ignored,
the equipment begins shutdown procedures to maintain the charge
of the battery. Refer to Informational Displays Prior to Shutdown.
An optional power adapter can be purchased and provides
sustained power to the equipment. If you plan to change the club
settings, the power adapter is highly recommended. To purchase
the optional power adapter, check with your dealer. Refer to
Obtaining Service.
Informational Displays Prior to
Shutdown
The equipment saves its battery charge by moving into a shutdown
mode. If the user does not maintain the minimum rate of motion, a
30-second shutdown process begins.
Dots appear in the display and all key presses are ignored. If no
movement is detected or the rate of motion remains below the
minimum, the dots steadily disappear as the countdown continues.
Note: The user can resume exercising if he or she begins before
the countdown period elapses.
Important: If the equipment is connected to a CSAFE master
device, a slightly different scenario occurs. When ten seconds
remain before the equipment shuts off, the exercise session ends.
RESETTING
appears in the display while the equipment
disconnects from the CSAFE master device. All key presses are
ignored.
Product Owner's Manual: Self-Powered Features 10
Symptoms of a Low Battery
If no one has used the equipment for an extended period of time,
the battery may need recharging.
Symptoms of a low battery include:
y
y
A flickering or erratic display
User and program information is lost once the user stops
exercising. No workout summary or notification of pending
shutdown occurs.
Important: To maintain a constant power source, use the optional
power adapter.
Using the Optional Power Adapter
After connecting the power adapter to the equipment, plug the
opposite end into the appropriate power source 120 V or 240 V.
CAUTION: When the optional power adapter is in use, make sure
that the power supply cord does not create a safety hazard. Keep
it out of the way of traffic and moving parts. If the power supply
cord or power conversion module is damaged, it must be
replaced.
The display functions differently when the power adapter is
connected. Because the power adapter provides a constant source
of power, a user can pause for brief periods without initiating
shutdown procedures. When the pause time limit expires and the
user has not resumed exercising, the display returns to the Precor
banner. Refer to Setting a Pause Time Limit. To learn how to install
the power adapter, refer to The Optional Power Adapter Kit.
Product Owner's Manual: Self-Powered Features 11
Product Owner's Manual: Self-Powered Features 12
The Optional Power Adapter Kit
If you purchase the optional power adapter, you must also
purchase the internal cable kit. The kit supplies the cable, bracket,
and fasteners that connect the power adapter to the lower
electronics board.
CAUTION: The internal cable kit must be installed by authorized
service personnel. Do not attempt installation on your own as
you could void the Precor Limited Warranty. For more
information, refer to Obtaining Service.
Once the internal cable kit is installed, you can plug the optional
power adapter into the equipment. Plug the opposite end into the
appropriate power source for your equipment 120 V or 240 V.
Review the safety instructions found at the beginning of this manual
before using the power adapter.
Replacing the Battery
The equipment’s battery is built to last for a long time. However, if
you feel that the battery may need replacing, check with an
authorized service technician. Refer to Obtaining Service.
CAUTION: The battery stored inside the equipment contains
hazardous materials and must be disposed of according to
Hazardous Waste Regulations. Refer to Hazardous Materials
and Proper Disposal.
Club Features
These next few pages explain how to customize the equipment for
your club or facility and view useful product information. All these
features remain hidden to the patrons and can only be accessed
using special key presses. Read this section if you want to:
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
Enable or disable the safety code (treadmill)
Change the display to a different language
Change the display to show U.S. standard or metric
measurements
Set the maximum exercise and pause times
Set a cool-down time limit
Set the maximum speed and incline (treadmill)
Enable or disable hidden programs or remote access (treadmill)
Change the auto-level setting (EFX)
Set the resistance range (cycle)
Customize a program
View the odometer
Display the number of hours the equipment has been in use
View the software versions and part numbers
Display the serial number
Check the program usage and error logs
Note: To review the club programming prompts and factory
default settings that can be changed through club programming
mode, refer to the following table.
Product Owner's Manual: Club Features 13
Product Owner's Manual: Club Features 14
y
y
y
y
Club Programming Tips
Always start at the Precor banner.
Electrical power must be supplied.For self-powered equipment,
a constant power source is available if you use the optional
power adapter, otherwise you will have to maintain the minimum
rate of motion. Refer to Self-Powered Features. If you plan to
program self-powered equipment, purchasing the optional
power adapter is highly recommended.
Note: If you do not use the optional power adapter during club
programming mode, and the rate of motion falls below the
minimum requirements, no warning is given when the equipment
moves into its 30-second shutdown procedure.
The club programming mode is accessed by pressing the
RESET key at the Precor banner. The remaining key presses
must occur quickly and without pause.
Note: Treadmill keys that can be used interchangeably in club
programming mode are: PAUSE/RESET and the red STOP
button. On the EFX, the CLEAR and ENTER keys perform
specific functions, but the number keypad is disabled once you
enter club programming mode.
The changes made in club programming mode become the
default settings whenever the display resets to the Precor
banner.
Table 2. Club custom features and settings
Equipment Club Programming Prompt Factory Default
Setting
Changes you can make
Treadmill
SAFETY CODE
Disabled
An enabled safety code requires a 4-digit entry code before users can access any exercise
programs.
All *
SELECT LANGUAGE
English Several languages affect the display prompts. Choose one.
All *
SELECT UNITS
U.S. Two standard units of measure affect the display prompts. Choose between U.S. or Metric.
All *
SET MAX WORKOUT TIME
60 minutes
Exercise session time limits range from 1 to 240 minutes. NO LIMIT is accessible beyond
240 minutes.
All *
SET MAX PAUSE TIME
120 seconds
Pause time limits range from 1 to 120 seconds (2 minutes). Restrictions exist for
self-powered units.
All *
SET COOL DOWN TIME
5 minutes Cool-down time limits range from 0 to 5 minutes.
Treadmill
SET SPEED LIMIT
Maximum speed
available.
Refer to Treadmill: Determining the Club Speed Limit.
Treadmill
SET INCLINE LIMIT
Maximum grade
possible.
Refer to Treadmill: Setting an Incline Limit.
Treadmill †
HIDDEN PROGRAMS
Hide programs Two options are available: Show Programs or Hide Programs. Choose one.
Treadmill
REMOTE SPEED
CONTROL
Disabled
A computer must be connected through the CSAFE port to enable this feature and change
the speed or incline for a specific user.
EFX576i,
EFX546i
SET CROSSRAMP
AUTO-LEVEL
Mid-level of ramp
incline range
This prompt only appears on EFX units which have adjustable ramps. Settings range from 1
to 20. Refer toEFX: Changing the Auto-Level Setting.
Cycle
SET RESISTANCE
RANGE
High
Settings range from High, Medium, and Low. Refer toCycle: Setting a Resistance Range.
All †
SET CUSTOM PROGRAM 1
Random profile
Modify the program profile. Refer toCreating a Custom Program.
Treadmill †
SET CUSTOM PROGRAM
2
Random profile
Modify the program profile. Refer to Creating a Custom Program.
* This feature is available in all Precor equipment.
† This program is not available on the 946i treadmill, EFX546i, and EFX556i.
Note: If a user changes the language or unit of measure during an exercise session, the display resets to the club preferences when a user’s workout ends.
Product Owner's Manual: Club Features 15
Accessing Club Programming Mode
and Changing the Settings
Read the Club Programming Tips to identify useful information
about customizing your Precor equipment.
To access the available menus and change the program settings,
perform the following steps:
At the Precor banner, press the following keys in sequence
without pausing between selections:
RESET, 5, 6, 5, 1, 5, 6, 5
Note: A PAUSE/RESET key appears on some products and
functions the same as the RESET key.
The club programming prompts appear sequentially and in a
menu format. The following table describes which keys to use in
club programming mode.
Table 3. Club Programming Mode keys
Key Description Function
▲
or
▼
Navigational arrow
keys
Moves you through the programs
and selections.
OK OK key
Lets you choose or accept the
displayed selection.
BACK BACK key
Returns to the previous menu level
without saving any changes.
RESET
RESET key or
PAUSE/RESET key
Exits Club Programming Mode
and returns to the Precor banner.
1.
Note: The number keypad is disabled once you enter club
programming mode.
Product Owner's Manual: Club Features 16
Use the following flowchart to navigate through the menu settings on treadmills.
SELECT UNITS
SET MAX PAUSE TIME
SET MAX WORKOUT TIME
PAUSE/RESET, 5, 6, 5, 1, 5, 6, 5
SELECT LANGUAGE
OK
[ENGLISH]
[U.S.]
[60 MIN]
[120 SEC.]
OK
▼
OK
OK
▼
OK
OK
▼
▼
PRECOR
DIAGS – SET CLUB PARAMETERS
OK
OK
SAFETY CODE[DISABLED]
OK
OK
▼
SET INCLINE LIMIT
[INCLINE 15.0]
OK
HIDDEN PROGRAMS*
▼
[HIDE PROGRAMS]
OK
OK
REMOTE SPEED CONTROL
▼
[DISABLED]
OK
OK
SET CUSTOM PROGRAM 1*
▼
[RANDOM]
OK
SET CUSTOM PROGRAM 2*
▼
[RANDOM]
OK
OK
SET SPEED LIMIT
[16.0 MPH]
OK
▼
OK
OK
SET COOL DOWN TIME[5 MIN.]
▼
OK
OK
* This program is not available on the 946i treadmill.
Product Owner's Manual: Club Features 17
Use the following flowchart to navigate through the menu settings
on ellipticals.
SELECT UNITS
SET MAX PAUSE TIME
SET MAX WORKOUT TIME
RESET, 5, 6, 5, 1, 5, 6, 5
SELECT LANGUAGE
OK
[ENGLISH]
[U.S.]
[60 MIN]
[120 SEC.]
OK
▼
OK
OK
▼
OK
OK
▼
▼
PRECOR
SET COOL DOWN TIME
[5 MIN.]
DIAGS – SET CLUB PARAMETERS
OK
OK
OK
▼
OK
SET CROSSRAMP AUTO-LEVEL
[XRAMP 10]
OK
SET CUSTOM PROGRAM 1*
▼
[RANDOM]
OK
OK
Use the following flowchart to navigate through the menu settings
on cycles.
SELECT UNITS
SET MAX PAUSE TIME
SET MAX WORKOUT TIME
RESET, 5, 6, 5, 1, 5, 6, 5
SELECT LANGUAGE
OK
[ENGLISH]
[U.S.]
[60 MIN]
[120 SEC.]
OK
▼
OK
OK
▼
OK
OK
▼
▼
PRECOR
SET COOL DOWN TIME
[5 MIN.]
DIAGS – SET CLUB PARAMETERS
OK
OK
OK
▼
OK
SET RESISTANCE RANGE
[HIGH]
OK
SET CUSTOM PROGRAM 1
▼
[RANDOM]
OK
OK
* This program is not available on the EFX546i and EFX556i.
Product Owner's Manual: Club Features 18
Use the following flowchart to navigate through the menu settings
on climbers.
SELECT UNITS
SET MAX PAUSE TIME
SET MAX WORKOUT TIME
RESET, 5, 6, 5, 1, 5, 6, 5
SELECT LANGUAGE
OK
[ENGLISH]
[U.S.]
[60 MIN]
[120 SEC.]
OK
▼
OK
OK
▼
OK
OK
▼
▼
PRECOR
SET COOL DOWN TIME
[5 MIN.]
DIAGS – SET CLUB PARAMETERS
OK
OK
OK
▼
OK
SET CUSTOM PROGRAM 1[RANDOM]
OK
Treadmill: Selecting Safety Code
Protection
When the equipment is shipped from the factory, the safety code
protection feature is disabled. If you enable the safety code, your
patrons will need to enter four number keys in sequence to begin
their exercise session and, on the treadmill, start the running belt. If
the correct keys are not pressed within two minutes, further access
is denied. For more information, refer toEntering the Safety Code.
1.At the
SAFETY CODE
prompt, press OK. Use the navigational
arrow keys to alternate between the two selections.
Setting Description
ENABLED
Causes the safety code prompt to appear prior to a
workout and when returning from pause mode.
DISABLED
Does not require a safety code to operate.
CAUTION: Do not assume the equipment is safe because of
safety code protection. Never leave children unsupervised
around the equipment.
2.When you are ready, press OK to accept the displayed setting
and move to the next feature. For further options, refer to the
table in Accessing Club Programming Mode and Changing the
Settings.
Product Owner's Manual: Club Features 19
Choosing a Language
The equipment can display user prompts, text, and user entries in
several different languages. When the equipment is shipped from
the factory, it is set to display English.
Note: Programming prompts are not affected by language
selection. The prompts in this section continue to appear in
English.
1.
2.
1.
2.
At the
SELECT LANGUAGE
prompt, press OK. Use the
navigational arrow keys to choose a language.
When you are ready, press OK to accept the displayed setting
and move to the next feature. For other options, refer to the table
in Accessing Club Programming Mode and Changing the
Settings.
Selecting a U.S. Standard or Metric
Display
The equipment can display measurements in either Metric or U.S.
Standard. The default factory setting is to display U.S. Standard. To
change this setting, perform the following steps:
At the
SELECT UNITS
prompt, press OK. Use the navigational
arrow keys to select a unit of measure (
US
or
METRIC
).
CAUTION: If you change the Unit of Measure display on a
treadmill, be sure to check the speed setting to verify that it is
correct. Refer to Treadmill: Determining the Club Speed
Limit.
When you are ready, press OK to accept the displayed setting
and move to the next feature. For other options, refer to the table
in Accessing Club Programming Mode and Changing the
Settings.
Product Owner's Manual: Club Features 20
Setting an Exercise Session Time Limit
You can limit how long a user can exercise on the equipment. For
example, if you set the time limit to 20 minutes, users can only enter
a session time between 1 and 20 minutes.
Note: The automatic cool-down period is appended to the end of
any time-based program, so adjust the time limit accordingly.
You can also let a user exercise indefinitely by selecting
NO LIMIT
.
However, you will need to instruct users that once they select a
program, they must press the TIME +/- key. A workout time blinks
in the display. They need to use the Number Keypad to type in 240,
press the up arrow key to display
NO LIMIT
, and then press OK.
The exercise session times available are between 1 and 240
minutes.
Note: The Military Performance Programs will not complete if the
maximum exercise time limit is less than 40 minutes. Set the
maximum session time above 40 minutes if you have allowed users
to access these programs. Refer to Treadmill: Accessing
Performance Programs.
1.
2.
At the
SET MAX WORKOUT TIME
prompt, press OK. Use the
navigational arrow keys to change the displayed time limit.
Note: When you press and hold a navigational arrow key, the
number increments by five, for example, 1, 5, 10, 15, 20. When
you tap an arrow key, the number increments by one.
When you are ready, press OK to accept the displayed setting
and move to the next feature. For other options, refer to the table
in Accessing Club Programming Mode and Changing the
Settings.
Product Owner's Manual: Club Features 21
Setting a Pause Time Limit
You can limit how long a user can pause while exercising on the
equipment by entering a time between 1 and 120 seconds (two
minutes). For example, if you set a pause time limit of 60 seconds,
the display automatically resets to the Precor banner if no
movement is detected and no key press occurs for one minute.
Important: The optional power adapter must be connected on
self-powered equipment to establish a definitive pause time limit. If
the optional power adapter is not attached and the rate of motion
drops below the minimum requirements, the equipment begins its
30-second shutdown, effectively eliminating pause mode. Refer to
the table in Self-Powered Features.
1.
2.
1.
2.
At the
SET MAX PAUSE TIME
prompt, press OK. Use the
navigational arrow keys to change the time limit. Choose
between 1 and 120 seconds (two minutes).
When you are ready, press OK to accept the displayed setting
and move to the next feature. For other options, refer to the table
in Accessing Club Programming Mode and Changing the
Settings.
Setting a Cool-Down Time Limit
You can limit how long a user cools down after exercising on the
equipment by entering a time between 0 and 5 minutes.
Important: It is highly recommended that you set the cool-down
period at or above three minutes. It takes time for a user’s heart
rate to return to a resting state after vigorous exercise. An effective
cool-down period also reduces the amount of lactic acid in muscle
tissue.
At the
SET COOL DOWN TIME
prompt, press OK. Use the
navigational arrow keys to display the available time limits.
Choose between 0 and 5 minutes. The default setting is 5
minutes.
When you are ready, press OK to accept the displayed setting
and move to the next feature. For other options, refer to the table
in Accessing Club Programming Mode and Changing the
Settings.
Product Owner's Manual: Club Features 22
Treadmill: Determining the Club Speed
Limit
You can set a maximum speed for the treadmill. This limits how fast
the running belt moves and, consequently, the number of speed
settings that are available to the user. The speed is displayed in
miles per hour (mph) or kilometers per hour (kph) depending upon
the units of measure (U.S. standard or Metric) selected earlier. The
speed ranges from 0.5 to 16 mph (0.8 to 25.5 kph).
Important: If you select a number that limits the miles per hour,
your change will not affect the kilometers per hour (and vice
versa). The treadmill does not convert the speed entered in mph
(U.S. standard) to kph (Metric). It stores separate numbers for the
different units of measure. To enter both values, you must first
reset the display to the appropriate unit of measure, and then
change the speed limit in this program. Refer to Selecting a U.S.
Standard or Metric Display.
1.
2.
At the
SET SPEED LIMIT
prompt, press OK. Use the
navigational arrow keys to select the desired running belt speed
limit.
When you are ready, press OK to accept the displayed setting
and move to the next feature. For other options, refer to the table
in Accessing Club Programming Mode and Changing the
Settings.
Treadmill: Setting an Incline Limit
You can set the maximum grade (percent of incline) for the
treadmill. This limits the degree of incline and, consequently, the
number of incline settings that are available to the user. The
available rangeis:
Treadmill Percent of Incline
C956i 0 to 15% grade
C966i -3 to 15% grade
1.
2.
At the
SET INCLINE LIMIT
prompt, press OK. Use the
navigational arrow keys to select the desired grade.
When you are ready, press OK to accept the displayed setting
and move to the next program. For other options, refer to the
table in Accessing Club Programming Mode and Changing the
Settings.
Product Owner's Manual: Club Features 23
Treadmill: Accessing Performance
Programs
Note: This feature is not available on the 946i treadmill.
Several performance-based programs on the treadmill can be
hidden from the user’s view and, consequently, be unavailable
during an exercise session. These programs are shown in the
following list:
Gerkin Fitness Test, USAF PRT, NAVY PRT, ARMY PFT, USMC
PFT, Federal Law Enf. PEB.
If you keep the default factory setting, the Track and 5K programs
are available to the user through the PERFORMANCE key.
If you wish to change this setting, perform the following steps:
1.Press OK to review the current
HIDDEN PROGRAMS
selection.
Use the navigational arrow keys to alternate between the two
selections.
Setting Description
SHOW
PROGRAMS
Causes all the Performance Programs listed above
to appear. The user can access each program
through the PERFORMANCE key on the display.
HIDE
PROGRAMS
Hides the Performance Programs listed above and
makes them inaccessible to the user. However, the
Track and 5K programs remain available and are
accessed when a user presses the
PERFORMANCE key.
2.When you are ready, press OK to accept the displayed setting
and move to the next program. For other options, refer to the
table in Accessing Club Programming Mode and Changing the
Settings.
Product Owner's Manual: Club Features 24
Treadmill: Changing Remote Control
Access
1.
Important: To affect this setting, the treadmill must be connected
to a computer and you will need to be familiar with CSAFE
commands.
When you enable this program, you can set a user’s speed and
incline through a computer software program which interfaces with
the CSAFE port on the treadmill.
The default factory setting is set to
DISABLED
. To change this
setting, perform the following steps:
At the
REMOTE SPEED CONTROL
prompt, press OK. Use
the navigational arrow keys to alternate between the two
selections.
Setting Description
ENABLED
Lets you set the speed and incline for individual users
and their selected program using CSAFE commands
through a computer connection.
DISABLED
Disconnects remote access so you cannot use the
remote capabilities of a CSAFE connection. You
would also use this setting when the treadmill is not
connected to a computer.
2.When you are ready, press OK to accept the displayed setting
and move to the next program. For other options, refer to the
table in Accessing Club Programming Mode and Changing the
Settings.
Product Owner's Manual: Club Features 25
EFX: Changing the Auto-Level Setting
1.
2.
3.
You can set a specific ramp incline so that the EFX automatically
returns to it at the end of a workout session. Whatever incline you
set, the EFX ramp returns to the setting if a user continues
pedaling, once the program session has ended, and presses
RESET to return to the Precor banner.
Note: This setting is available on equipment with adjustable ramps.
Important: If you use this feature, connecting the optional power
adapter is recommended. Instruct users about the auto-leveling
feature and ask that they hold onto a stationary handrail with one
hand while the equipment automatically moves to the set incline.
At the
SET CROSSRAMP AUTO-LEVEL
prompt, press OK.
XRAMP
n appears, where n is the ramp incline setting. Some
displays only show a number without prefacing it with
XRAMP
.
Use the navigational arrow keys to select the desired ramp
incline setting from 1 to 20.
When you are ready, press OK to accept the displayed setting
and move to the next feature. For other options, refer to the table
in Accessing Club Programming Mode and Changing the
Settings.
Product Owner's Manual: Club Features 26
Cycle: Setting a Resistance Range
You can set a low, medium or high range of resistance on the
recumbent or upright cycles. Within each setting, 25 levels of
resistance are available, but the chosen setting affects the overall
resistance range.
Physical therapy conditioning is an example where you might use
this programming feature. If a user has an injury that needs low
levels of resistance, you might set the resistance range to low to
make sure thatthe user does not induce further injury by exceeding
your recommended levels of resistance.
The following table provides short descriptions of each group.
Table 4. Resistance range settings on cycles
Setting Description
HI or
HIGH
Provides the full range of resistance available. If an upright
cycle user chooses the high-end resistance levels, the cycle
provides enough resistance to simulate sprinting or hill
climbing for users wishing to stand on the upright cycle. It
also provides enough resistance for elite riders that are
capable of spinning at high speed with high resistance.
MED or
MEDIUM
Provides approximately two thirds of the resistance that is
available within the high group setting. Club owners may
want to select the medium range for recumbent cycles. Since
users cannot stand on recumbent cycles, less resistance is
needed by the average (non-elite) user. A medium range may
provide more comfort. It also allows users to make easier
resistance changes in the preset programs.
LO or
LOW
Provides approximately one third of the resistance that is
available within the high group setting. The low range may be
appropriate in special situations where poorly conditioned
users are anticipated. The low range is not recommended for
the club environment.
1.
2.
At the
SET RESISTANCE RANGE
prompt, press OK. Use the
navigational arrow keys, to choose
LOW
,
MEDIUM
or
HIGH
(
LO
,
MED
, or
HI
on some equipment).
When you are ready, press OK to accept the displayed setting
and move to the next feature. For other options, refer to the table
in Accessing Club Programming Mode and Changing the
Settings.
Product Owner's Manual: Club Features 27
Product Owner's Manual: Club Features 28
1.
2.
3.
Creating a Custom Program
Note: This feature is not available on the 946i treadmill, EFX546i
and EFX556i.
When you design a custom program, you are preprogramming the
program profile.
At the
SET CUSTOM PROGRAM
prompt, press OK. The
program profile appears in the display and a blinking column
indicates your starting point.
Note: Two custom programs are available on the treadmill. All
other Precor products contain one custom program. The prompt
indicates which one you have accessed. For example,
SET
CUSTOM PROGRAM 1
scrolls across the display to indicate you
are selecting the first custom program. If you have a treadmill
and wish to select the second custom program, press the down
arrow key on the navigational keypad, before pressing OK in
step 6.
When the Custom Program profile appears, press the down
arrow key on the navigational keypad, to select the column you
wish to change.
To change the height of the column, refer to the following table.
Table 5. Custom Program keys
Equipment Key Description
Treadmill INCLINE keys
Changes the column height and
affects the Custom Program incline.
EFX
CROSSRAMP
keys
Changes the column height and
affects the Custom Program ramp
incline.
Cycle
RESISTANCE
keys
Changes the column height and
affects the Custom Program pedal
resistance.
Climber
RESISTANCE
keys
Changes the height of the column
and affects the Custom Program
step resistance.
4.
5.
6.
When the column height is set, press the down arrow key on
the navigational keypad, to move to the next column. You can
press the up arrow key to move back and change earlier
columns as needed.
Continue adjusting the profile for each column.
When you are ready, press OK to save the program profile and
return to the Precor banner.
Note: If you prefer to exit the program without saving changes to
the custom profile, press BACK.
Loading...
+ 84 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.