Planet ISW-800T-M12 User Manual

1. Package Contents

Thank you for purchasing PLANET Industrial IP67-rated 8-Port 10/100Mbps M12 Ethernet Switch, ISW-800T-M12. In the following sections, the term “Industrial M12 Ethernet Switch” means the ISW-800T-M12.

Open the box of the Industrial M12 Ethernet Switch and carefully unpack it. The box should contain the following items:

Industrial M12

Ethernet Switch x 1

1.2m M12 Power Cable x 1

User’s Manual x 1

DIN-rail Kit x 1 Wall Mount Kit x 1

1.2m M12-to-RJ45 UTP Cable x 1

Power LED: Power 1/Power 2 (Green),

LED Indicators

FAULT (Green) 10/100BASE-TX Port (Port-1 to Port-8): LNK/ACT (Green)

10BASE-T: 2-pair UTP Cat.3,4,5 up to 100m (328ft)

Network Cables

100BASE-TX: 2-pair UTP Cat.5, 5e, 6 up to 100m (328ft) EIA/TIA-568 100-ohm STP (100m, max.)

Switch Specications

Switch Processing Scheme

Store-and-Forward

Address Table 2K entries

Flow Control

Back pressure for half duplex IEEE

802.3x Pause Frame for full duplex

Switch Fabric 1.6Gbps

Throughput (packet per second)

Maximum Transmit Unit

1.19Mpps@64Bytes

1536 bytes

3. Hardware Introduction

3.1 Front Panel

The front panel of the Industrial M12 Ethernet Switch consists of Ethernet interfaces and LED indicators.

 Front View

DC Input: 9-48V

, 0.5A max.

LNK/ACT

V2V2V1

Fault

PWR 2

PWR 1

LNK ACT

IP67 M12

TXRXRX

ISW-800T-M12

3.2 M12 DC Power Cable Pinout

The Industrial M12 Ethernet Switch front panel provides one M12 A-coded 5-pin male connector for DC power input; please use the power cable with M12 A-coded 5-pin female connector from Industrial M12 Ethernet Switch package for DC power input. The Industrial M12 Ethernet Switch power input port pinout is shown below:

ISW-800T-M12

INPUT

DC 9V~48V

Pinout 1: V1

Pinout 2: V1+

Pinout 3: V2+

Pinout 4: V2

Please follow the steps below for DC power cable installation on Industrial M12 Ethernet Switch.

1. Plug the DC power cord connector to the power input port of

the Industrial M12 Ethernet Switch.

2. Screw the nut on DC power cord female connector to the DC power input male connector of Industrial M12 Ethernet Switch and make sure the connection is tight.

Before DC power cord connection, please check

Note

and assure your local DC power source is stable.

- 1 -

If any of these pieces are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

2. Product Specications

Model ISW-800T-M12

Hardware Specications

10/100BASE-TX Ports

Power Connector

Enclosure IP67 aluminum

Dimensions (W x D x H)

Weight 976g

Power Requirements

Power Consumption/ Dissipation

Installation DIN-rail kit and wall mount ear

ESD Protection 6KV DC

8 x M12, 4-Pin D-coded female connector

1 x M12, 5-Pin A-coded male connector

103 x 53 x 163mm

9~48V DC, redundant power with reverse polarity protection

4watts/13BTU

Standards Conformance

Standards Compliance

Regulatory Compliance

Stability Testing

Environment

Temperature

Humidity

- 3 -

IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet IEEE 802.3x Flow Control and Back Pressure

FCC Part 15 Class A, CE

IEC60068-2-32 (Free fall) IEC60068-2-27 (Shock) IEC60068-2-6 (Vibration)

Operating: -40~75 degrees C Storage: -40~75 degrees C

Operating: 5~95% (non-condensing) Storage: 5~95% (non-condensing)

Figure 3-1: ISW-800T-M12 Front View

- 5 -

 System LEDs

LED Color Function

PWR 1 Green Lit: To indicate power 1 has power.

PWR 2 Green Lit: To indicate power 2 has power.

Fault Green

Lit: To indicate either power 1 or power 2 has no power.

 10/100BASE-TX M12 Interface LEDs

LED Color Function

Lit: To indicate the Switch is successfully connecting to the network at 10/100Mbps.

LNK/ ACT

Green

Blink: To indicate that the Switch is actively sending or receiving data over that port.

O: To indicate the Switch is not

connecting to the network at 10/100Mbps.

- 7 -

3.3 10/100BASE-TX Ports with M12 Interface

Cable Pinout

The Industrial M12 Ethernet Switch front panel provides eight RJ45 10/100BASE-TX ports and M12 interfaces. These ports are designed for Ethernet equipment connection. The Industrial M12 Ethernet Switch 10/100Mbps M12 input interface pinout is shown below:

ISW-800T-M12

Pinout 1: TX+

Pinout 2: RX+

Pinout 3: TX

Pinout 4: RX -

1 2 3 6

Signal MDI MDI-X TX+

RX+

TX+

142

Pinouts for the RJ45 (8-Pin) Port

RJ45 (8-Pin)

1 8

Please follow the steps below for the 10/100Mbps M12 cable installation of Industrial M12 Ethernet Switch.

1. Plug the 10/100Mbps M12 cable male connector to the Ethernet female connector input port of the Industrial M12 Ethernet Switch.

2. Screw the nut on 10/100Mbps M12 cable male connector to the Ethernet input female connector of Industrial M12 Ethernet Switch and make sure the connection is tight.

- 2 -

- 4 -

- 6 -

- 8 -

As each Ethernet port of Industrial M12 Ethernet

Taiwan

July 22, 2020

Country

Date

Legal Signature

Switch is running in auto negotiation mode, make sure the opposite Ethernet devices Ethernet

Note

ports are also running in auto negotiation mode, otherwise, the Ethernet performance will be poor.

4. Installation

This section guides you to installing the Industrial M12 Ethernet Switch on the DIN rail and wall. Please read this chapter completely before continuing.

5. Three-View Diagram

54.6

DC Input:

9-48V

, 0.5A max.

PWR 1

IP67 M12

ISW-800T-M12

104

LNK/ACT

PWR 2

Fault

123

LNK/ACT

ACT

LNK

53 9

In the installation steps below, this manual uses PLANET IGS-801 8-port Industrial Gigabit Switch

Note

as an example. The steps for PLANET Industrial M12 Ethernet Switch are similar.

- 9 -

4.1 DIN-rail Mounting Installation

4.2 Wall-mount Plate Mounting

48.8

163

100

188 204

103

100

Unit: mm

Figure 5-1: ISW-800TM12 Three-View Diagram

- 11 -

6. Customer Support

Thank you for purchasing PLANET products. You can browse

our online FAQ resource on PLANET web site rst to check if it

could solve your issue. If you need more support information, please contact PLANET support team.

PLANET online FAQs: http://www.planet.com.tw/en/support/faq

Support team mail address: support@planet.com.tw

FCC Warning

This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WEEE Warning

To avoid the potential eects on the environment and

human health as a result of the presence of hazardous substances in electrical and electronic

equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

EC Declaration of Conformity

I hereby confirm that the following equipment complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (2014/30/EU).

Type of Product:

Industrial IP67 Rated 8-Port 10/100Mbps M12 Ethernet Switch

Models:

ISW-800T-M12

Produced by:

Manufacturer’s Name: Planet Technology Corporation

Manufacturer’s Address: 10F., No.96, Minquan Rd., Xindian Dist.,

For the evaluation regarding the EMC, the following standards were applied:

EN 55032 (2015 + AC:2016)

EN 55024 (2010 + A1:2015)

EN 55035 (2017)

Person responsible for making this declaration

Name: Kent Kang

Title: Director

New Taipei City 231, Taiwan, R.O.C.

Caution

You must use the screws supplied with the wallmounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty.

- 10 -

Copyright © PLANET Technology Corp. 2020. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

- 12 - - 13 -

PLANET TECHNOLOGY CORPORATION

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528

e-mail: sales@planet.com.tw http://www.planet.com.tw