Planet ISW-501T operation manual

1. Product Introduction

1.1 Package Contents

Check the contents of your package for the following parts:

 Industrial Fast Ethernet Switch x 1

 User’s Manual x 1

 DIN Rail Kit x 1

 Wall-mount Kit x 1

If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them again
to repack the product in case there is a need to return it to
us for repair.

1.2 Product Features

 Physical Port

 5-port 10/100BASE-TX RJ45 with auto MDI/MDI-X

function (ISW-501T)

 8-port 10/100BASE-TX RJ45 with auto MDI/MDI-X

function (ISW-801T)

1.3 Product Specications

Model ISW-501T ISW-801T

Hardware Specications

10/100BASE-TX Ports 5 8

3 x LED for System and Power:
Green: DC Power 1

LED Indicators

Enclosure IP30-rated metal case

Dimensions
(W x D x H)

Weight 400g 428g

ESD Protection 6KV DC

EFT Protection 6KV DC

Power Requirements

Power Consumption/
Dissipation

Installation DIN rail kit and wall-mount ear

Alarm

Connector

Green: DC Power 2
Green: Power Fault
1 x LED per Copper Port
Green: 10/100 LNK/ACT

135 x 87 x 32 mm

12~48V DC, redundant power with polarity
reverse protection function, 24V AC power
support

1.6 watts/5.4BTU 2.1 watts/7.1BTU

Provides one relay output for power failure
Alarm relay current carry ability: 3A @ DC
30V

Removable 6-pin terminal block
Pin 1/2 for Power 1;
Pin 3/4 for fault alarm;
Pin 5/6 for Power 2

2. Hardware Introduction

2.1 Switch Front Panel

Figures 2-1 and 2-2 show the front panels of Industrial Fast
Ethernet Switches.

P1 P2 FAULT

1

2

3

4

5

10/100

LNK
ACT

ISW-501T

Figure 2-1: ISW-501T Front

Panel

Figure 2-2: ISW-801T Front

10/100

LNK
ACT

Panel

P1 P2 FAULT

1

2

3

4

5

6

7

8

ISW-801T

3. Installation

3.1 Wiring the Power Inputs

The Upper Panel of the Industrial Fast Ethernet Switch
indicates a DC inlet power socket and consists of one
terminal block connector within 6 contacts. Please follow
the steps below to insert the power wire.

1. Insert positive/negative DC power wires into Contacts 1
and 2 for Power 1 or 5, and 6 for Power 2.

1 2 3 4 5 6

V1+ V1- V2+ V2-

PWR1

2. Tighten the wire-clamp screws for preventing the wires
from loosening.

1 2 3 4 5 6

V1+ V1- V2+ V2-

Power 1 Fault Power 2

PWR2Fault

Input
DC12~48V, AC 24V

- 1 -

 Layer 2 Features

 Complies with IEEE 802.3 10BASE-T, IEEE 802.3u

100BASE-TX Ethernet standard

 Supports auto-negotiation and 10/100Mbps half/full

duplex mode

 High performance Store and Forward architecture,

runt/CRC ltering eliminates erroneous packets to

optimize the network bandwidth

 Prevents packet loss with back pressure (half-duplex)

and IEEE 802.3x pause frame ow control (full-du­plex)

 Backplane (switching fabric): ISW-501T: 1Gbps,

ISW-801T: 1.6Gbps

 Automatic address learning and address aging

 Industrial Case & Installation

 IP30 metal case

 DIN rail and wall-mount design

 12 to 48V DC, redundant power with polarity reverse

protect function and connective removable terminal
block for master and slave power, 24V AC power
support

 Lower Power Consumption device under full loading

operation mode

 Supports EFT protection for 6000 VDC for power line

 Supports 6000 VDC Ethernet ESD protection

 -40 to 75 degrees C operating temperature

 Free fall, shock-proof and vibration-proof for industries

- 3 -

Switch Specications

Switch Processing
Scheme

Address Table 1K

Buffer Memory Embedded 448K bits packet buffer

Flow Control

Switch Fabric 1Gbps 1.6Gbps

Throughput
(packet per second)

Network Cables

Standards Conformance

Standards
Compliance

Temperature

Humidity

Regulatory
Compliance

Stability Testing

Store-and-Forward

Back pressure for half duplex,
IEEE 802.3x pause frame for full duplex

0.74Mpps 1.19Mpps

10BASE-T: 2-pair UTP Cat. 3, 4, 5, up to

100 meters

100BASE-TX: 2-pair UTP Cat. 5, 5e up to

100 meters

IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3x Full Duplex Flow Control

IEEE 802.3az Energy Efcient Ethernet

Operating: -40~75 degrees C
Storage: -40~75 degrees C

Operating: 5% to 95%,
Storage: 5% to 95% (non-condensing)

FCC Part 15 Class A, CE

IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)

- 5 -

2.2 LED Indicators

LED Color Function

P1 Green Lit: indicates Power 1 has power.

P2 Green Lit: indicates Power 2 has power.

FAULT Green

10/100
LNK/
ACT

Lit: indicates either Power 1 or Power 2 has no

power.

Lit: indicates the port is successfully connecting to

the network at 100Mbps or 10Mbps.

Off: indicates that the port is not successfully

Green

connecting to the network at 100Mbps or
10Mbps.

Blinking: indicates that the port is actively

sending or receiving data.

2.3 Switch Upper Panel

The upper panel of the Industrial Fast Ethernet Switch
consists of one terminal block connector within two DC
power inputs.

Figure 2-3 shows the upper panel of the Industrial Fast
Ethernet Switch.

1 2 3 4 5 6

V1+ V1- V2+ V2-

PWR1

Figure 2-3: Industrial Fast Ethernet Switch Upper Panel

PWR2Fault

Input
DC12~48V, AC 24V

- 7 -

The wire gauge for the terminal block should

Note

be in the range between 12 and 24 AWG.

3.2 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal
block connector as the picture shows below. Inserting the
wires, the Industrial Fast Ethernet Switch will detect the
fault status of the power failure and then forms an open
circuit. The following illustration shows an application
example for wiring the fault alarm contacts.

Insert the wires into the fault alarm contacts

1. The wire gauge for the terminal block should
be in the range between 12 and 24 AWG.

Note

2. Alarm relay circuit accepts up to 30V, max.
3A currents.

- 2 -

- 4 -

- 6 -

- 8 -

The Fault Alarm Contacts are
energized (CLOSE) for normal

Fault Alarm Contacts

Fault

operation and will OPEN when
failure occurs

3.3 DIN-rail Mounting Installation

The DIN rail is screwed on the Industrial Fast Ethernet
Switch when out of factory. When you need to replace
the wall mount application with DIN-rail application on
Industrial Fast Ethernet, please refer to the following gures
to screw the DIN rail on the Industrial Fast Ethernet Switch.
To hang the Industrial Fast Ethernet Switch, follow the
steps below:

Step 3: Check whether the DIN rail is tightly on the track.

Step 4: Please refer to the following procedures to remove

the Industrial Fast Ethernet Switch from the track.

1

2

Step 5: Lightly pull out the bottom of DIN rail to remove it

from the track.

3.4 Wall-mount Plate Mounting Installation

To install the Industrial Fast Ethernet Switch on the wall,
please follow the instructions described below.

Step 1: Remove the DIN rail from the Industrial Fast

Ethernet Switch; loosen the screws to remove the
DIN rail.

- 9 -

Step 1: Screw the DIN rail on the Industrial Fast Ethernet

Switch.

1

2

Step 2: Place the bottom of DIN rail lightly into the track.

- 11 -

Step 2: Place the wall-mount plate on the rear panel of

the Industrial Fast Ethernet Switch.

Step 3: Use the screws to screw the wall-mount plate on

the Industrial Fast Ethernet Switch.

Step 4: Use the hook holes at the corners of the wall-

mount plate to hang the Industrial Fast Ethernet
Switch on the wall.

Step 5: To remove the wall-mount plate, reverse the steps

above.

Customer Support

Thank you for purchasing PLANET products. You can browse

our online FAQ resource at PLANET Web site rst to check

if it could solve your issue. If you need more support
information, please contact PLANET switch support team.

PLANET online FAQ :
http://www.planet.com.tw/en/support/faq.php?type=1

Switch support team mail address :
[e-mail]

EC Declaration of Conformity

For the following equipment:

*Type of Product: 5/8-Port 10/100Mbps Industrial Ethernet Switch
*Model Number: ISW-501T, ISW-801T

* Produced by:
Manufacturer‘s

Name : Planet Technology Corp.

Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,

is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive
on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:

EN 55022 (Class A:2010/AC:2011)
EN 61000-3-2 (2014)
EN 61000-3-3 (2013)
EN 55024 (2010)

Responsible for marking this declaration if the:

 Manufacturer  Authorized representative established within the EU

Authorized representative established within the EU (if applicable):

Company Name: Planet Technology Corp.

Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan

Person responsible for making this declaration

Name, Surname Kent Kang

Position / Title : Director

New Taipei City 231, Taiwan (R.O.C.)

IEC 61000-4-2 (2008)
IEC 61000-4-3 (2006+A1:2008+A2:2010)
IEC 61000-4-4 (2012)
IEC 61000-4-5 (2005)
IEC 61000-4-6 (2013)
IEC 61000-4-8 (2009)
IEC 61000-4-11 (2004)

(R.O.C.)

- 10 -

Copyright © PLANET Technology Corp. 2016.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.

- 12 - - 13 -

Taiwan 25 March, 2016

Place Date Legal Signature

PLANET TECHNOLOGY CORPORATION

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]

e-mail: [e-mail] http://www.planet.com.tw