Planet ISW-1600T operation manual

Industrial Multi-port 10/100TX

Fast Ethernet Switch

ISW-1600T/IFGS-1822TF

Version 1.0

User's Manual

2.ProductSpecications

Product ISW-1600T IFGS-1822TF

Hardware Specications

Fast Ethernet Copper Ports

Gigabit Ethernet Copper Ports

SFP Slots --

Switch Architecture Store-and-Forward

Switch Fabric

Throughput (packet per second)

Address Table

Shared Data Buer 4Mbits

16 10/100BASE-TX RJ45 auto-MDI/MDI-X ports

Two

10/100/1000BASE-T

RJ45 auto-MDI/MDI-X ports (shared with Port-17 and Port-18)

Two 1000BASE-SX/ LX/BX SFP interfaces (shared with Port-17 and Port-18)

3.2Gbps (non-blocking)

7.2Gbps (non-blocking)

2.38Mpps@ 64 bytes 5.36Mpps@ 64 bytes

16K entries, automatic source address learning and aging

IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab Gigabit

1000T

IEEE 802.3z Gigabit SX/LX IEEE 802.3x ow control and back pressure IEEE 802.1p Class of

Standards Compliance

IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3x ow control and back pressure IEEE 802.1p Class of Service IEEE 802.3az Energy Ecient Ethernet (EEE)

Service IEEE 802.3az Energy Ecient Ethernet (EEE)

Environment

Operating Temperature

Storage

Temperature

-40 ~ 75 degrees C

-40 ~ 85 degrees C

Humidity 5 ~ 95% (non-condensing)

3.2 LEDDenition:

 System

LED Color Function

DC1 Green Lights to indicate DC power input 1 has power.

DC2 Green Lights to indicate DC power input 2 has power.

Fault Red

 Per 10/100BASE-TX Port

LED Color Function

LNK/ ACT

100 Speed

Green

Amber

Lights to indicate that AC or DC power has failed.

Lights to indicate the link through that port is successfully established.

Blinking to indicate that the switch is actively sending or receiving data over that port.

O to indicates that the port is linked down.

Lights to indicate that the port is operating at

100Mbps.

O to indicates that the port is operating at

10Mbps.

O to indicates that the port is linked down.

- 1 -

1. Package Contents

Thank you for purchasing PLANET Industrial Multi-port 10/100TX Fast Ethernet Switch, ISW-1600T/IFGS-1822TF. In the following sections, the term “Industrial Ethernet Switch” means the

ISW-1600T or IFGS-1822TF.

Open the box of the Industrial Ethernet Switch and carefully unpack it. The box should contain the following items:

Industrial Ethernet

Switch x 1

RJ45 Dust Cap x 16 DIN-rail Kit SFP Dust Cap x 2

If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

User’s Manual x 1 Wall-mount Kit x 1

(IFGS-1822TF only)

- 3 -

Flow Control

IEEE 802.3x pause frame for full-duplex Back pressure for half-duplex

ESD Protection 6KV DC

Enclosure IP30 metal case

Installation DIN-rail kit and wall-mount kit

Removable 6-pin terminal block for power

Connector

input Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin 5/6 for Power 2

Alarm

Dimensions (W x D x H)

One relay output for power failure. Alarm relay current carry ability: 1A @ 24V DC

66 x 107 x 152 mm 66 x 107 x 152 mm

Weight 255g 300g

Power

Requirements

Power

Consumption

Dual 12~48V DC, 24V AC

Max. 5.3 watts/18BTU (Ethernet full loading)

Max. 6.3 watts/21.4BTU (Ethernet full loading)

Standards Conformance

Regulatory Compliance

FCC Part 15 Class A, CE

IEC60068-2-32 (free fall)

Stability Testing

IEC60068-2-27 (shock) IEC60068-2-6 (vibration)

- 5 -

3. Hardware Introduction

3.1 Switch Front Panel

The front panel of the Industrial Ethernet Switch consists of Ethernet interfaces and LED indicators.

 Front View

P1 P2 Fault

100

ACTLNK

ISW-1600T

Figure1:

ISW-1600T Front View

P1 P2 Fault

100

1000X

挖孔

1000T

1000

ACTLNK

IFGS-1822TF

Figure2:

IFGS-1822TF Front View

- 7 -

 Per Gigabit RJ45/SFP Combo Interface (Port-17~Port-18 of IFGSW-1822TF)

LED Color Function

Lights to indicate the link through that port is successfully established.

LNK/ ACT

Green

Blinking to indicate that the switch is actively sending or receiving data over that port.

O to indicates that the port is linked down.

Lights to indicate that the port is operating at

1000Mbps.

1000 Speed

Amber

O to indicates that the port is operating at

10/100Mbps.

O to indicates that the port is linked down.

3.3 Switch Upper Panel

The upper panel of the Industrial Ethernet Switch consists of one terminal block connector within two power input and one relay

ouput.

Max. fault loading: 24V, 1A

1 2 3 4 5 6

V1+ V1- V2+ V2-

PWR1

PWR2Fault

Figure3: ISW-1600T and IFGS-1822TF Top View

DC Input: 12-48V AC Input: 24V

, 1A max.

, 2A max.

- 2 -

- 4 -

- 6 -

- 8 -

3.4 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of Industrial Ethernet Switch is used for two DC redundant power inputs. Please follow the steps below to insert the power wire.

When performing any of the procedures like inserting the wires or tightening the wire-clamp screws, make sure the power is OFF to prevent from getting an electric shock.

1. Insert positive and negative DC power wires into contacts 1 and 2 for POWER 1, or contacts 5 and 6 for POWER 2.

Max. fault loading: 24V, 1A

1 2 3 4 5 6

4. Installation

This section describes the functionalities of the Industrial Ethernet Switch’s components and guides you to installing it on the DIN rail and wall. Please read this chapter completely before continuing.

This following pictures show how to install the device. However, the device in the picture is not ISW-1600T

Note

4.1 DIN-rail Mounting Installation

or IFGS-1822TF.

V1+ V1- V2+ V2-

PWR1

PWR2Fault

DC Input: 12-48V AC Input: 24V

, 1A max.

, 2A max.

2. Tighten the wire-clamp screws for preventing the wires from loosening.

1 2 3 4 5 6 Power 1 Fault Power 2 + - + -

- 9 -

1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG.

2. The power input range is 12V ~ 48V DC and

Note

supports 24V AC.

3. Use one power input when using 24V AC.

3.5 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Ethernet Switch will detect the fault status of the power failure and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts.

1 2 3 4 5 6

- 11 -

4.2 Wall-mount Plate Mounting

4.3 Side Wall-mount Plate Mounting

5. Customer Support

Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET web site rst to check if it could solve your issue. If you need more support information, please contact PLANET switch support team.

PLANET online FAQ: http://www.planet.com.tw/en/support/faq

Switch support team mail address: support@planet.com.tw

FCC Warning

This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Fault Alarm Contacts

1. The wire gauge for the terminal block should be in

Note

2. Alarm relay circuit accepts up to 24V DC,1A

The Fault Alarm Contacts are energized (CLOSE) for normal operation and will OPEN when

Fault

failure occurs

Insert the wires into the fault alarm contacts

the range between 12 and 24 AWG.

- 10 -

WEEE Warning

To avoid the potential eects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end

users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

- 12 - - 13 - - 14 -