Planet IPOE-162S operation manual

1. Package Contents

Note

Top View

Front View

Side View

Mounting Kit

Thank you for purchasing PLANET Industrial IEEE

802.3at Gigabit High Power over Ethernet Splitter, IPOE162S. The term “802.3at PoE Splitter” used in this user’s manual refers to the IPOE-162S.

Open the box of the Industrial IEEE 802.3at Gigabit High Power over Ethernet Splitter and carefully unpack it. The box should contain the following items:

Industrial IEEE 802.3at Gigabit High Power over

Ethernet Splitter x 1

User’s Manual x 1

DIN Rail Kit x 1

 Wall Mount Kit x 1

If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

Industrial Case / Installation

IP30 metal case protection

 DIN Rail and Wall-mount type

 Supports EFT protection of 6000 VDC for power

line

 Supports 6000 VDC Ethernet ESD protection

 -40 to 75 degrees C operating temperature

PSE (Power Sourcing Equipment) is a device (switch or hub for instance) that will provide power in a PoE setup. Maximum allowed continuous output power per such device in IEEE 802.3af is 15.4W and in IEEE

802.3at is 25W. PDs (Powered Devices), such as IP phones, network cameras, wireless access points, etc., are PoE-enabled terminals powered by a PSE and thus consumes energy.

10/100/1000Base-T: 4-Pair UTP Cat.

Network Cable

Power over Ethernet

PoE Standard

Number of device can be powered

Standards Conformance

Standards Compliance

Regulation Compliance FCC Part 15 Class A, CE

Stability Testing

Standards Conformance

Operating Temperature -40 ~ 75 degrees C

Storage Temperature -40 ~ 85 degrees C

Humidity 5 ~ 95% (non-condensing)

5, 5e, 6 distance up to 100m (328ft) EIA/TIA-568 100-ohm STP (100m)

IEEE 802.3at High Power over Ethernet

1 or 2 (Varies on device power requirements; DC1 + DC2 cannot be over 25 watts)

IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.3at High Power over Ethernet

IEC60068-2-32 (Free fall) IEC60068-2-27 (Shock) IEC60068-2-6 (Vibration)

5. Product Outlook

Figure 1: Front panel of IPOE-162S

LED Indicators

LED Color Function

Power Ready

Green

Lights to indicate the port is receiving 48~56V DC in-line power and ready for output

- 1 -

2. Product Features

Interface

2 RJ-45 interfaces

1-port PoE Power+ Data input

1-port Data output

2 DC out (4-pin Terminal Block)

Power over Ethernet Splitter

 Complies with IEEE 802.3at Power over Ethernet,

 Splits the 48~56V DC power over RJ-45 Ethernet

cable into 12 / 24V DC output

 Up to 1 non-IEEE 802.3at PoE device powered

 Auto-detects PoE IEEE 802.3at equipment and

protects devices from being damaged with incorrect installation

 Adjustable two different output voltage options

(12V / 2A, 24V / 1A) to t various devices

 Distance up to 100 meters

- 3 -

3. Product Specications

Product IPOE-162S

Hardware Specications

“PoE (Power + Data)” Input Port

Interface

Data Rate

LED Indicator System: Power Ready x 1 (Green)

DIP Switch 12V DC / 24V DC output voltage

Power Input 802.3at PoE 48~56V DC

Power Output 12V / 24V DC, Max 2A (adjustable)

Dimensions (W x D x H)

Weight 421g

Enclosure IP30 metal case

Installation DIN rail kit and wall mount ear

ESD Protection 6KV DC

“Data” Out Port

DC Out Plug Connector

1 x RJ-45 10/100/1000Base-T

1 removable 4-pin terminal block

10/100/1000Mbps (vary on Ethernet device attached)

135 x 87.8 x 32 mm

- 5 -

4. Physical Dimensions

Rear View

Mounting Kit

DIN-Rail Kit

- 7 -

6. Hardware Installation

The following section describes the hardware features of the IPOE-162S. Before connecting any network device to the IPOE-162S, read this chapter carefully.

6-1 Before Installation

If there is no power socket in your network environment, the IPOE-162S provides DC power for this Ethernet Device conveniently and easily. The IPOE-162S will separate the power and data out. It provides two kinds of DC power output through its DIP switch and its voltage and current shown below:

 12V DC / 2A

 24V DC / 1A

Figure 2: DIP Switch Outlook

- 2 -

- 4 -

- 6 -

- 8 -

Hint

Please check the power requirements of

Note

Maximum Output 25 Watts

Output 25 Watts

the device carefully, that is going to get the power from IPOE-162S.

1. If the power requirement is higher than the IPOE-162S can supply, current overload might shut down the IPOE-162S itself. Thus, it will also shut down your device as well.

2. Please ensure the output voltage is correct for remote device. Otherwise, it will damage your remote device.

3. Forbid to switch on/off the Power DIP during operation. Otherwise, it will damage your IPOE-162S and remote device. If you want to switch the output Voltage DIP, please Plug OFF the “POE In” cable and wait for 3 seconds until the POE LED (Power) is completely OFF.

6-3 Wiring the Power Outputs

Please follow the steps below to insert the power wires.

Step 1: Please nd one terminal block connector within

two DC power outputs shown below:

1 V-

2 V-

3 V+

DC Output 2

DC Output 1

4 V+

The wire gauge for the terminal block should be in the range of 12 ~ 24 AWG.

Step 2: Insert the Negative / Positive DC wires into the

V– / V+ terminal; terminals 1 and 3 for Power 1; terminals 2 and 4 for Power 2.

- 9 -

6-2 4-pin Power Output Terminal Block

From top to down, there are Negative (V-), Negative (V-), Positive (V+) and Positive (V+), and two sets of DC power output contact.

Figure 3: DC Power Output Terminal Block Outlook

Two DC outputs are sharing 12V 2A or 24V 1A, totaling 25W PoE output power, which means that DC1 + DC2 cannot be over the 25W PoE output power. Otherwise, it might cause the power output to malfunction or damage.

- 11 -

Step 3: Connect the other point of DC power wires

to the power devices. Tighten the wire-clamp screws for preventing the wires from loosening.

Powered

Device

One Powered Device

Powered

Device

Total Maximum

Powered

Device

Step 4: Install the terminal block on PLANET IPOE-

162S Splitter.

Step 5: Connect the network copper cable (RJ-45)

from the High Power Injector (PSE) and it will provide power to PLANET IPOE-162S Splitter and the IPOE-162S will separate the power and data to the PDs (power devices). Please see the Figure below:

802.3at PSE

802.3at PoE+ Data in

10/100/1000T Copper

Data Out

DC+

Non-PoE

Device

Customer Support

Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET Web site

rst to check if it could solve your issue. If you need

more support information, please contact PLANET switch support team.

PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php?type=2

Switch support team mail address : support_switch@planet.com.tw

- 10 -

Two Powered Device

- 12 - - 13 - - 14 -

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.