Pioneer XW-BTSA1-N User Manual

WIRELESS SPEAKER SYSTEM

Radio wave caution

Store the AC adapter out of the reach of

CAUTION

XW-BTSA1

Operating Instructions

-K/-W/-N

Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC

Manufacturer:

PIONEER CORPORATION

1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa

EU Representative’s:

Pioneer Europe NV

Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium

http://www.pioneer.eu212-0031, Japan

Português:

Pioneer declara que este [*] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.

Pioneer tímto prohlašuje, že tento [*] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES

Pioneer izjavlja, da je ta [*] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.

Prin prezenta, Pioneer declara ca acest

[*] este in conformitate cu cerintele esentiale si alte prevederi ale Directivei 1999/5/EU.

Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.

Table of contents

Before you start

Part names and functions

Getting started

Bluetooth Audio playback

Other Connections

Additional Information

Discover the benefits of registering your product online at

http://www.pioneer.co.uk

(or

http://www.pioneer.eu

http://www.pioneer.co.uk

http://www.pioneer.eu

PIONEER CORPORATION

1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

PIONEER ELECTRONICS (USA) INC.

P. O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404

PIONEER ELECTRONICS OF CANADA, INC.

340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.

Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270

K002_B3_En

[*] XW-BTSA1-K, XW-BTSA1-W, XW-BTSA1-N

English:

Hereby, Pioneer, declares that this [*] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Suomi:

Pioneer vakuuttaa täten että [*] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Nederlands:

Hierbij verklaart Pioneer dat het toestel [*] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG

Français:

Par la présente Pioneer déclare que l’appareil [*] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE

Svenska:

Härmed intygar Pioneer att denna [*] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Dansk:

Undertegnede Pioneer erklærer herved, at følgende udstyr [*] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF

Deutsch:

Hiermit erklärt Pioneer, dass sich dieses [*] in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)

Ελληνικά:

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Pioneer ΔΗΛΩΝΕΙ ΟΤΙ [*] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ

Italiano:

Con la presente Pioneer dichiara che questo [*] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Español:

Por medio de la presente Pioneer declara que el [*] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE

Eesti:

Käesolevaga kinnitab Pioneer seadme [*] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele

sätetele.

Magyar:

Alulírott, Pioneer nyilatkozom, hogy a [*] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Ar šo Pioneer deklarē, ka [*] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Šiuo Pioneer deklaruoja, kad šis [*] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Malti:

Hawnhekk, Pioneer jiddikjara li dan [*] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC

Pioneer týmto vyhlasuje, že [*] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.

С настоящето, Pioneer декларира, че този [*] отговаря на основните изисквания и други съответни постановления на Директива

1999/5/EC.

Polski:

Niniejszym Pioneer oświadcza, że [*] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC

Norsk:

Pioneer erklærer herved at utstyret [*] er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv

1999/5/EF.

Íslenska:

Hér með lýsir Pioneer yfir því að [*] er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun

1999/5/EC

Hrvatski:

Ovime tvrtka Pioneer izjavljuje da je ovaj [*] u skladu osnovnim zahtjevima i ostalim odredbama Direktive

1999/5/EC.

R-TTE-24L_C1_En

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

D3-4-2-1-1_B1_En

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

D3-4-2-1-3_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

D3-4-2-1-7b*_A1_En

Operating Environment

Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light).

D3-4-2-1-7c*_A2_En

CAUTION

The

switch on this unit will not completely shut off

all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

When using this product, confirm the safety information shown on the bottom of the unit.

D3-4-2-2-2a*_A1_En

D3-4-2-2-4_B1_En

WARNING

Store small parts out of the reach of children and infants. If accidentally swallowed, contact a doctor immediately.

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

D41-6-4_A1_En

K041_A1_En

S002*_A1_En

Printed in China

children and infants.

The AC adapter cord may accidentally wind around the

neck and it may cause suffocation.

AC adapter CAUTION

• Make sure to grasp the body of the AC adapter when removing it from the power outlet. If you pull the power cord, it may become damaged which could lead to fire and/or electrocution.

• Do not attempt to plug in or remove the AC adapter

with wet hands. This may result in electrocution.

• Do not insert the power cord of AC adapter into a

power outlet where the connection remains loose despite inserting the prongs all the way into the outlet. Heat may be generated which could lead to fire. Consult with the retailer or an electrician regarding replacement of the power outlet.

This unit uses a 2.4 GHz radio wave frequency, which is a band used by other wireless systems (Microwave ovens and Cordless phones, etc.). In this event noise appears in your television image, there is the possibility this unit (including products supported by this unit) is causing signal interference with the antenna input connector of your television, video, satellite tuner, etc. In this event, increase the distance between the antenna input connector and this unit (including products supported by this unit).

• Pioneer is not responsible for any malfunction of the compatible Pioneer product due to communication error/malfunctions associated with your network connection and/or your connected equipment. Please contact your Internet service provider or network device manufacturer.

• A separate contract with/payment to an Internet service provider is required to use the Internet.

<1202-0001015>

Condensation

If the player is moved suddenly from a cold place into a warm room (in winter, for example) or if the temperature in the room in which the player is installed rises suddenly due to a heater, etc., water droplets (condensation) may form inside (on operating parts and the lens). When condensation is present, the player will not operate properly and playback is not possible. Let the player stand at room temperature for 1 or 2 hours with the power turned on (the time depends on the extent of condensation). The water droplets will dissipate and playback will become possible. Condensation can also occur in the summer if the player is exposed to the direct wind from an air-conditioner. If this happens, move the player to a different place.

S005_A1_En

Information for users on collection and disposal of old equipment and used batteries

Symbol for

equipment

Symbol examples

for batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

These symbols are only valid in the European Union. For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

K058a_A1_En

Specications

Amplier section

RMS Power Output: ................................................8 W+8 W

Speaker section

System ...........................................................Bass-reflex type

Speakers:

Fullrange ............................................................63 mm x 2

Tweeter ...............................................................13 mm x 2

Frequency range ........................................... 80 Hz to 20 kHz

Bluetooth section

Communication method .......... Bluetooth Standard Ver. 4.0

Class ............................................................................ Class 2

Supported codec .................................................. SBC, apt-X

Maximum communication distance ............................. 10 m

Miscellaneous

USB (for charging) ..................................................... 5 V, 1 A

Power consumption .......................................................15 W

In standby ......................................................0.5 W or less

Dimensions (W) x (H) x (D)

..................................................290 mm x 102 mm x 143 mm

Weight (without package and AC adapter) ................ 1.4 kg

AC adapter

Power requirements

...............................................AC 100 V to 240 V, 50 Hz/60 Hz

Rated output ............................................. DC 14 V, 2000 mA

Accessories

AC adapter ............................................................................ 1

Power plug ............................................................................ 2

Remote Control ..................................................................... 1

Lithium Battery (CR2025)* ................................................... 1

*The lithium battery has been factory installed in the

remote control unit.

Warranty card ....................................................................... 1

Operating instructions (This document)

Note

• Specifications and the design are subject to possible modifications without notice, due to improvements.

(RMS, 1 kHz, 1 %, T.H.D., 8 Ω)

About the AC adapter

Safety instructions

To ensure your personal safety and to maximize the full operating potential of your unit, read and follow these safety instructions.

Read & Retain Instructions

Read all operating and user information provided with this product.

Cleaning

Use a damp cloth to clean the exterior housing. Avoid using any fluids including liquid, aerosol or alcoholbased cleaning products.

Water or Moisture

Avoid operating or locating this product near water or other sources of fluid.

Accessories

Do not place this product on an unstable cart, stand, or table. The product may fall and be seriously damaged.

Ventilation

Do not block or cover this product in use. This unit should not be placed in a built-in installation unless properly ventilated.

Environment

Avoid placing this product in a location with exposure to large quantities of dust, high temperatures, high humidity, or subject to excessive vibrations or shocks.

Power Sources

Operate this product only from the recommended power sources. If you are unsure of the power source, consult an authorized Pioneer representative.

Power-Cord Protection

When unplugging the unit, pull on the plug – not on the cord. Do not handle the cord or plug with wet hands; doing so could cause an electric short or shock. Do not allow anything to pinch or rest on the power cord and do not place in a walkway.

Power

Turn OFF the system before installing this or any other hardware device.

Overloading

Avoid connecting too many devices to a single wall socket or power source as this can cause fires or short circuits.

Object & Liquid Entry

Never push inappropriate objects in to the device. Avoid spilling any liquids in to or on the outside of the drive.

Servicing

Opening or removing the cover exposes you to possible electrical shock or other danger. Contact a Pioneer authorized service representative for repairing this product

(refer to the enclosed Service & Support Card).

Damage Requiring Service

Unplug the unit and refer servicing to qualified service personnel in the following situations:

! When the power cord, plug, or chassis is damaged. ! If liquid has been spilled, or objects have fallen into the

product.

! If the product has been exposed to rain or water. ! If the product does not operate normally when the

operating instructions are followed. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and can require extensive work by a qualified technician to restore the unit to its normal operation.

! When the product exhibits a distinct change in

performance – this indicates a need for service. Check that there are no irregularities with the AC adapter or power plug, then insert the power plug into the specified position of the AC adapter using the specified procedure until a click is heard. For details, see Mounting the power plug on chapter 1. If there are irregularities with the AC adapter or power plug, ask your nearest Pioneer authorized service center or your dealer to carry out repair work. ! Do not use this unit with a coin, paper clip or other metal

object stuck between the AC adapter and power plug.

Doing so could cause a short circuit, leading to fire or

electric shock.

! When mounting the AC adapter on a wall outlet, make

sure there is no space between the AC adapter and the

wall outlet. Faulty contact or a coin, paper clip or other

metal object getting stuck in the space could cause a short

circuit, leading to fire or electric shock.

Coin, paper clip or other metal object

Side Top

! The power plug could come detached from the AC adapter

and remain in the power outlet if someone trips on the AC adapter’s power cord or if something hits the AC adapter. If this happens, remove the power plug remaining in the outlet with dry hands, holding it as shown on the diagram below and without touching metal parts. Do not use any tools to remove it.

Do not touch metal parts.

PUSH

Before you start

What’s in the box

• AC adapter × 1

• Power plug × 2

• Remote Control × 1

• Lithium Battery (CR2025) * The lithium battery has been factory installed in the

remote control unit.

• Warranty card × 1

• Operating Instructions (This Document)

Before using the remote control

The battery supplied with this unit is stored in the battery casing. Remove the protective seal from the battery casing.

Note

• When you notice a decrease in the operating range, replace the battery.

Replace the battery

When replacing the battery, use a commercially available Lithium CR2025 battery.

1 Flip the remote control and pull out the

battery holder by pushing the tab to the right.

2 Place a new battery in the casing.

Make sure the + side of the battery is facing up when you place it in the space provided.

3 Push back the battery holder.

The battery included with the unit is to check initial operations; it may not last over a long period.

WARNING

About lithium battery

• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.

• Dispose of used battery cells immediately after replacement. Keep away from children. If swallowed, please contact a doctor immediately.

• Lithium batteries may present a fire or chemical burn hazard if misused. Do not disassemble, heat above 100 ºC, or incinerate.

• Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.

Caution

Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:

• Remove the battery if the unit isn’t going to be used for a month or more. In the event of battery fluid leakage, wipe up any fluid inside the case and install a new battery.

• When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country or area.

Mounting the power plug

Slide the power plug along the guide rails in the AC adapter unit as shown on the diagram below, then press in until a click is heard.

PUSH

Removing the power plug

While pressing the [PUSH] button on the AC adapter unit, slide the power plug away from the adapter as shown on the diagram below to remove it.

Once the power plug is mounted, there is no need to remove it.

PUSH

Power plug

This product comes with the types of power plugs shown below. Use the appropriate power plug for the country or region you are in.

Type 1 (for Europe) Type 2 (for the UK)

Connect DC Power

• Connect the AC adapter’s DC plug to the DC IN jack on the back panel. Then connect the power plug on the other end to the power outlet.

• Use only the AC adapter included in this package. (Do not use the power adapter of different specification.)

DC IN 14V

Vol input

pairing

USBDC IN 14V AUX IN

Power outlet

5V 1A

Part names and functions

Top Panel

pairing

Vol input

123

1 standby/on button

• Switches the unit between Standby and On.

• Press and hold to perform pairing with Bluetooth

device.

2 Vol –/+

3 input button

4 input Indicator (The LED indicator is inside

button

Adjust the listening volume.

• The listening volume has a range from 0 to 29 (however, the unit is not equipped with a display to

visually indicate the volume level).

(Default setting: 11)

• If the volume is set within the range of 23 to 29, it will

be set to 23 automatically when the unit switches from standby mode to power on.

Switch the mode of Bluetooth and AUX.

the grill on the front panel.)

• Light up Indicate green when the unit is in AUX mode.

• Light up Indicate blue when the unit is in Bluetooth mode.

• Blink blue during waiting for Bluetooth connection.

• Blink blue quickly for Bluetooth pairing.

Back Panel

Vol input

pairing

USBDC IN 14V AUX IN

5V 1A

USBDC IN 14V AUX IN

5V 1A

1 DC IN 14V Jack

Connect the AC adapter.

2 USB connector

Use to charge the smartphone. Audio playback is not

supported. (Specification: 5V, 1A)

3 AUX IN Jack

Connect auxiliary components.

Remote Control

input

1 standby/on button

Switches the unit between Standby and On.

2 Playback control buttons

Use when operating the smartphone with this remote control.

3 vol –/+ button

Use to adjust the listening volume.

4 input button

Press to select the input source.

vol

Getting started

Turning on

Press the [standby/on] button. The indicator would light.

• The unit switches to the mode (Bluetooth mode or AUX mode) that was last used.

• The unit will be in Bluetooth mode when it is turned on

for the first time (when the AC adapter is connected to a

power outlet).

Note

• If no sound is output on this unit for 10 minutes or longer, the power turns off automatically (switch to standby mode).

• If the sound is played at low volume, this unit may turn the power off (switch to standby mode) automatically. Increase

the volume to prevent this from happening.

• If this unit automatically turns off (switches to standby mode)

in AUX mode, the power will automatically turn on if an audio signal is input from an external device connected via the AUX jack.

• If this unit automatically turns off (switches to standby mode)

in Bluetooth mode, the power will not turn on automatically.

This product enables you to enjoy listening to music wirelessly from a Bluetooth wireless technology enabled device (cell

phone, digital music player, etc.). You can also enjoy music

from a non-Bluetooth wireless technology enabled device using a Bluetooth audio transmitter available in stores. For details, refer to the user manual for the Bluetooth wireless technology enabled device.

This unit supports the SCMS-T content protection method. Music from Bluetooth wireless technology enabled devices which support the SCMS-T content protection method can be played back.

Bluetooth Audio playback

Music

INPUT

VOL

The unit

data

Caution

• Although the indicator light remains off while the unit’s power is off (in standby mode), there is still power flowing

to the unit at this time.

• If this unit was turned off (switched to standby mode) by

pressing the automatically turn on even if an audio signal is input from an external device connected via the AUX jack.

[standby/on] button, the power will not

Bluetooth wireless technology

enabled device:

Cell phone

Bluetooth wireless technology

enabled device:

Digital music player

Device not equipped with Bluetooth

wireless technology: Digital music player

Bluetooth audio transmitter

(commercially available)

Note

• The Bluetooth wireless technology enabled device must support A2DP profiles.

• Pioneer does not guarantee proper connection and operation of this unit with all Bluetooth wireless technology enabled devices.

• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by PIONEER CORPORATION is under license. Other trademarks and trade names are those of their respective owners.

Bluetooth Audio playback

Pairing this unit and Bluetooth wireless technology device

To enjoy music from a Bluetooth wireless technology enabled device, pairing is required with this product. Make sure to perform pairing first time you operate the system or any time pairing data is cleared.

Pairing is a step required to enable communication using Bluetooth wireless technology. For details, refer to the user manual of the Bluetooth wireless technology enabled device.

• Pairing is required when you first use Bluetooth wireless technology device and this unit.

• Up to eight Bluetooth wireless technology devices can be paired with the unit at one time.

• To enable Bluetooth communication, pairing should be done with both of your system and Bluetooth wireless technology device.

1 Select Bluetooth mode. The input indicator

inside the grill on the front panel blinks blue quickly and the unit will enter the pairing mode.

2 Switch on the Bluetooth wireless technology

device that you want to perform pairing with, place the device within 1 m of the system, and set it to the pairing mode.

Pairing begins.

• “Pairing” is the step necessary to register Bluetooth wireless technology device to enable Bluetooth communications. For more details, see also the operating instructions of your Bluetooth wireless technology device.

• In case of entering PIN code, use “0000”. ( Only “0000” works for PIN code in this product. )

3 When Bluetooth wireless technology device

has connected, the input indicator will change from blinking to lit.

4 Start playback of music contents stored in

Bluetooth wireless technology device.

Controlling devices with the remote control

The remote control that came with the unit can be used to control Bluetooth-enabled devices.

Note

• In order for it to be able to be controlled using the remote control for the unit, the Bluetooth-enabled device must support the AVRCP profile.

• The remote control is not guaranteed to work with all Bluetooth-enabled devices.

Connect the Latest Paired Bluetooth wireless technology Device

When the unit is switch on again to Bluetooth mode next time, it will be connected automatically with equipment that has the latest connected device already.

Connect previous Paired Bluetooth Device

1 If you want to connect other paired device

instead of the latest paired one, please make sure the Bluetooth connection of the latest device dis-connect. Then, the input indicator inside the grill on the front panel blinks quickly and the unit will change the waiting for connection mode.

You can also continue pressing the [standby/on] button so that the unit switches to waiting for connection mode, and then move on to the next step.

2 Switch on other paired device, and select this

unit from this device Bluetooth list.

3 Connection with other devices is successful,

the blue input indicator will change from blinking blue to lit.

Operating range of Bluetooth audio is up to 10 m. (Measured in open space. Walls and structures may

affect range of device.)

Connect with NFC / Pairing

NFC stands for “Near Field Communication” which enables establishing Bluetooth connection and paring by simply performing a few operations after holding an NFC-equipped smartphone up close to the unit.

Note

• Supported OS: Android 4.1 and above

• This may not operate properly, depending on the smartphone

or tablet device.

N Mark

pairing

Volinput

1 Check to make sure that the unit power is on

and then switch the unit to Bluetooth mode.

2 Hold the device to be connected up close to

the unit in the N Mark.

3 Pairing automatically begins.

4 When pairing is successful, the unit can be

used as Bluetooth speakers and music can be played back wirelessly.

The NFC function on this unit can be used when the unit is in Bluetooth mode.

Radio wave caution

This unit uses a 2.4 GHz radio wave frequency, which is a

band used by other wireless systems (see list below). To

prevent noise or interrupted communication, do not use this unit nearby such devices, or make sure these devices are switched off during use.

• Cordless phones

• Cordless facsimiles

• Microwave ovens

• Wireless LAN devices

• Wireless AV equipment

• Wireless controllers for game systems

• Microwave-based health aids

• Some baby monitors

Other, less common, equipment that may operate on the same frequency:

• Anti-theft systems

• Amateur radio stations (HAM)

• Warehouse logistic management systems

• Discrimination systems for train or emergency vehicles

Note

• In the event noise appears in your television image, there is the possibility that a Bluetooth wireless technology enabled device or this unit (including products supported by this

unit) are causing signal interference with the antenna input

connector of your television, video, satellite tuner, etc. In this event, increase the distance between the antenna input connector and the Bluetooth wireless technology enabled

device or this unit (including products supported by this unit).

• If there is something obstructing the path between this unit (including devices supported by this unit) and the device

equipped with Bluetooth wireless technology (such as a

metal door, concrete wall, or insulation containing tinfoil),

you may need to change the location of your system to prevent signal noise and interruptions.

Scope of operation

Use of this unit is limited to home use. (Transmission distances may be reduced depending on communication

environment.)

In the following locations, poor condition or inability to receive radio waves may cause the audio to be interrupted or stopped:

• In reinforced concrete buildings or steel framed or ironframed buildings.

• Near large metallic furniture.

• In a crowd of people or near a building or obstacle.

• In a location exposed to the magnetic field, static electricity

or radio wave interference from radio communication

equipment using the same frequency band (2.4 GHz)

as this unit, such as a 2.4 GHz wireless LAN device or microwave oven.

• If you live in a heavily populated residential area(apartment, townhouse, etc.) and if your neighbor’s microwave is

placed near your system, you may experience radio wave interference. If this occurs, move your unit to a different place. When the microwave is not in use, there will be no radio wave interference.

Radio wave reections

The radio waves received by this unit include the radio wave coming directly from the device equipped with Bluetooth

wireless technology (direct wave) and waves coming from

various directions due to reflections by walls, furniture

and building (reflected waves). The reflected waves (due to obstacles and reflecting objects) further produce a variety

of reflected waves as well as variation in reception condition depending on locations. If the audio cannot be received properly due to this phenomenon, try moving the location of the device equipped with Bluetooth wireless technology a little. Also note that audio may be interrupted due to the reflected waves when a person crosses or approaches the space between this unit and the device equipped with Bluetooth wireless technology.

• Before making or changing the connections, switch off

• When playing music through AUX mode, the music

Other Connections

the power and disconnect the AC adapter from the power outlet. Be sure to connect the AC adapter last.

volume will vary depending on the volume of the music player. If there is distortion when the volume is set at max, lower the music player’s volume and to avoid distortion.

Connecting auxiliary components

1 Connecting auxiliary components

Connect the back panel AUX IN jack to the analog

output jack (or headphone output jack) of the device to

be connected using the commercially available stereo mini-plug cable.

Digital audio player, etc.

Stereo mini-plug cable

(commercially available)

USBAUX IN

5V 1A

This unit’s back panel

AUX IN

2 Press [input] button.

Input indicator : green

3 Start playback of the auxiliary component.

Charging auxiliary components

Smartphones can be charged when they are connected to the unit using a commercially available USB cable.

1 Turn on the unit. 2 Use the USB cable to connect the unit and

the smartphone.

The smartphone will start charging.

USBDC IN 14V

5V 1A

Vol input

pairing

USBDC IN 14V AUX IN

Power

outlet

5V 1A

Additional Information

Troubleshooting

Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified even after checking the points below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

• If the unit does not operate normally due to external effects such as static electricity, disconnect the power plug from the outlet and insert it again to return to normal operating conditions.

Problem Remedy

The power does not turn on.

Power automatically switches to standby without user action.

No sound is output when a AUX mode is selected.

The Bluetooth wireless technology device cannot be connected or operated. Sound from the Bluetooth wireless technology device is not emitted or the sound is interrupted.

• Disconnect the power plug from the outlet, and insert again.

gChapter 1

• When this unit is not operated for 10 minutes or more, power will automatically turn OFF.

gChapter 3

• Make sure the component is connected correctly.

gChapter 5

• Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave oven, wireless LAN device or Bluetooth wireless technology

apparatus) is near the unit. If such an

object is near the unit, set the unit far from it. Or, stop using the object emitting the electromagnetic waves.

• Check that the Bluetooth wireless technology device is not too far from the unit and that obstructions are not set between the Bluetooth wireless technology device and the unit. Set the Bluetooth wireless technology device and the unit so that the distance between them is less

than about 10 m* and no obstructions

exist between them.

* The distance given is to be used as a

rough guide. The actual allowable distance between devices may vary depending on conditions in the surrounding environment.

• The Bluetooth wireless technology device may not be set to the communication mode supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless technology device.

Problem Remedy

• Check that pairing is correct. The pairing setting was deleted from this unit or the Bluetooth wireless technology device. Reset the pairing.

• Check that the profile is correct. Use a Bluetooth wireless technology device that

Pairing cannot be performed using the NFC function.

supports A2DP profile.

• Does the device to be connected support NFC?

• Is the NFC function on the device to be connected turned on?

• When pairing devices, move the N Mark on this unit close to where the NFC antenna on the device to be paired.

• Is the unit in Bluetooth mode?

• Use a compatible device with Android OS

4.1 or later.

• This may not operate properly, depending on the smartphone or tablet device.

gChapter 4

Cautions on use

When moving this unit

When moving this unit, press [standby/on] button, and then unplug the power cord.

Damage may occur when another device is connected to the AUX IN jack.

Place of installation

• Do not place this unit on top of a TV or color monitor. Also, install it away from cassette decks and other devices easily affected by magnetic forces.

• Avoid the following locations:

• Places exposed to direct sunlight

• Humid or poorly ventilated places

• Extremely hot places

• Places exposed to vibrations

• Places in which there is much dustt

• Places exposed to soot, steam, or heat (kitchens, etc.)

Do not place objects on this unit.

Do not place any objects on top of this unit.

Do not attach this unit to the wall or ceiling. It may fall off and cause injury.

Do not obstruct the ventilation holes.

Do not use this unit on shaggy rugs, beds, sofas, etc., or wrapped in cloth, etc. Doing so will prevent the heat from dispersing, leading to damage.

Do not expose to heat.

Do not place this unit on top of an amplifier or other components that generate heat. When rack mounting it, to avoid the heat given off by the amplifier or other audio components, place it on a shelf below the amplifier.

Turn off the power of this unit when not using it.

Depending on signal conditions, striped patterns may appear on a TV screen and noise may enter the sound of radio broadcasts when the power of this unit is on. If this happens, turn off the power of this unit.

Cleaning the this unit

• Unplug the power cord from the power outlet when cleaning this unit.

• Clean this unit using a soft cloth. For tough dirt, apply some neutral detergent diluted in 5 to 6 parts water to a soft cloth, wring out thoroughly, wipe off the dirt, and then wipe again with a soft, dry cloth.

• Alcohol, thinner, benzene, insecticides, etc., could cause the print or paint to peel off. Also, leaving rubber or vinyl products in contact with this unit for long periods of time could mar the cabinet.

• When using chemical-impregnated wipes, etc., read the cautions included with the wipes carefully.

• The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries.

• Android is a trademark of Google Inc.