Pioneer XW-BTS1-W User Manual [en, es, fr]
XW-BTS1
WIRELESS SPEAKER SYSTEM
Enceinte sans fil
Sistema de Altavoces Inalámbrico
Operating Instructions
Mode d’emploi
Manual de instrucciones
-K/-W
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with liquid
near this equipment (such as a vase or flower pot) or
expose it to dripping, splashing, rain or moisture.
WARNING
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the power
supply voltage of the area where this unit will be used
meets the required voltage (e.g., 230 V or 120 V) written
on the AC adapter label.
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
VENTILATION CAUTION
When installing this unit, make sure to leave space around
the unit for ventilation to improve heat radiation (at least
10 cm at top, 10 cm at rear, and 10 cm at each side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire hazard,
the openings should never be blocked or covered with
items (such as newspapers, table-cloths, curtains) or by
operating the equipment on thick carpet or a bed.
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
WARNING
Store small parts out of the reach of children and infants. If
accidentally swallowed, contact a doctor immediately.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
D3-4-2-1-3_A1_En
D3-4-2-1-4*_A1_En
D3-4-2-1-7a_A1_En
D3-4-2-1-7b*_A1_En
D3-4-2-1-7c*_A1_En
DO NOT OPEN
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed and
appropriate one fitted. Replacement and mounting of
an AC plug on the power supply cord of this unit should
be performed only by qualified service personnel.
If connected to an AC outlet, the cut-off plug can
cause severe electrical shock. Make sure it is properly
disposed of after removal.
The equipment should be disconnected by removing the
mains plug from the wall socket when left unused for a
long period of time (for example, when on vacation).
CAUTION
The
completely shut off all power from the AC outlet. Since
the power cord serves as the main disconnect device for
the unit, you will need to unplug it from the AC outlet
to shut down all power. Therefore, make sure the unit
has been installed so that the power cord can be easily
unplugged from the AC outlet in case of an accident.
To avoid fire hazard, the power cord should also be
unplugged from the AC outlet when left unused for a
long period of time (for example, when on vacation).
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
STANDBY/ON
switch on this unit will not
D3-4-2-1-1_A1_En
D3-4-2-2-1a_A1_En
D3-4-2-2-2a*_A1_En
K041_A1_En
2
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power cord
when your hands are wet as this could cause a short circuit
or electric shock. Do not place the unit, a piece of furniture,
etc., on the power cord, or pinch the cord. Never make a
knot in the cord or tie it with other cords. The power cords
should be routed such that they are not likely to be stepped
on. A damaged power cord can cause a fire or give you an
electrical shock. Check the power cord once in a while.
When you find it damaged, ask your nearest PIONEER
authorized service center or your dealer for a replacement.
AC adapter CAUTION
• Make sure to grasp the body of the AC adapter when
removing it from the power outlet. If you pull the
power cord, it may become damaged which could lead
to fire and/or electrocution.
• Do not attempt to plug in or remove the AC adapter
with wet hands. This may result in electrocution.
• Do not insert the power cord of AC adapter into a
power outlet where the connection remains loose
despite inserting the prongs all the way into the outlet.
Heat may be generated which could lead to fire.
Consult with the retailer or an electrician regarding
replacement of the power outlet.
Store the AC adapter out of the reach of children and
infants.
The AC adapter cord may accidentally wind around the
neck and it may cause suffocation.
S002*_A1_En
Radio wave caution
This unit uses a 2.4 GHz radio wave frequency, which is a
band used by other wireless systems (Microwave ovens
and Cordless phones, etc.). In this event noise appears
in your television image, there is the possibility this unit
(including products supported by this unit) is causing
signal interference with the antenna input connector of
your television, video, satellite tuner, etc. In this event,
increase the distance between the antenna input connector
and this unit (including products supported by this unit).
• Pioneer is not responsible for any malfunction of the
compatible Pioneer product due to communication
error/malfunctions associated with your network
connection and/or your connected equipment. Please
contact your Internet service provider or network
device manufacturer.
• A separate contract with/payment to an Internet
service provider is required to use the Internet.
[For European Users]
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used
electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to
designated collection facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential
negative effects on the environment and human health.
English
K058b_A1_En
3
[For American Users]
11)
Read these instructions.
1)
Keep these instructions.
2)
Heed all warnings.
3)
Follow all instructions.
4)
Do not use this apparatus near water.
5)
Clean only with dry cloth.
6)
Do not block any ventilation openings. Install in
7)
accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as
8)
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the polarized
9)
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or
10)
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets
the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment has very low levels of
RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that
it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding
extremities: hands, wrists, feet and ankles).
Information to User
Alterations or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
WARNING:
Handling the cord on this product or cords
associated with accessories sold with the product
may expose you to chemicals listed on proposition
65 known to the State of California and other
governmental entities to cause cancer and birth defect
or other reproductive harm.
Wash hands after handling.
D8-10-2_A1_En
D36-P5_B1_En
Only use attachments/accessories specified by
the manufacturer.
12)
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13)
Unplug this apparatus during lightning storms
or when unused for long periods of time.
14)
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
D3-7-13-69_En
D8-10-1-2_A1_En
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF
THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON YOUR ENCLOSED
WARRANTY CARD AND KEEP IN A SAFE PLACE FOR
FUTURE REFERENCE.
D36-AP9-1_A1_En
4
[For Canadian Users]
This Class B digital apparatus complies with Canadian
ICES-003.
This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of the device.
This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment
and meets RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment has very low levels
of RF energy that it deemed to comply without
maximum permissive exposure evaluation (MPE). But
it is desirable that it should be installed and operated
keeping the radiator at least 20cm or more away from
person’s body (excluding extremities: hands, wrists,
feet and ankles).
[For American Users and Canadian Users]
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a
safe level – a level that lets the sound come through
clearly without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing “comfort
level” adapts to higher volumes of sound, so what sounds
“normal” can actually be loud and harmful to your hearing.
Guard against this by setting your equipment at a safe
level BEFORE your hearing adapts.
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
• Once you have established a comfortable sound level,
set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:
• Do not turn up the volume so high that you can’t hear
what’s around you.
• Use caution or temporarily discontinue use in
potentially hazardous situations.
• Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.
D8-10-1-3_A1_En
S001a_A1_En
English
5
[For American Users and Canadian Users]
Register your product at:
http://www.pioneerelectronics.com (US)
http://www.pioneerelectronics.ca (Canada)
• Protect your new investment
The details of your purchase will be on file for reference in the event of an
insurance claim such as loss or theft.
• Receive free tips, updates and service bulletins on your new
product
• Improve product development
Your input helps us continue to design products that meet your needs.
• Receive a free Pioneer newsletter
Registered customers can opt in to receive a monthly newsletter.
[For European Users]
Discover the benefits of registering your product online at
http://www.pioneer.co.uk
(or
http://www.pioneer.eu
).
6
Table Of Contents
Before Start .....................................................................................8
Accessory Check Up
Connect DC Power
Part names and functions ..............................................................9
Top Panel
Back Panel
Getting started ..............................................................................11
Turning on
APS mode
Bluetooth Audio playback ...........................................................12
Other Connections ........................................................................16
Additional Information ................................................................17
Troubleshooting
Cautions on use
Specifications
* There will not be additional notification in this booklet if there is/ or will be any design
change to the product itself.
* Thank you for the purchase of Pioneer product, please read Operating Instructions
before use for the 1st time for correct operation. Keep this Operating Instructions for
your future reference.
English
7
Before Start
1. Accessory Check Up
Check the following items when opening the package:
• AC adapter × 1
• Rubber foot × 4
• Warranty card × 1
• Operating Instructions (This Document)
2. Connect DC Power
• Connect the AC adaptor’s DC plug to the DC IN jack on the back panel. Then connect the
power plug on the other end to the power outlet.
• Use only the AC adapter included in this package, do not use the power adapter of
different specification.
DC IN
8
Part names and functions
Top Panel
123 4 5 6
1.
MODE Indicator
• Light up Indicate green when the unit
is in Bluetooth mode.
• Light up Indicate orange when the unit
is in AUX mode.
• In the standby mode, light up Indicate
red for 3 seconds when APS
• In the standby mode, light up Indicate
green for 3 seconds when APS is ON.
2.
STANDBY/ON
• Switch between standby and on.
Press and hold to go into standby.
INPUT
• Switch the mode of Bluetooth and
AUX.
3.
Play / Pause
• Play/pause/resume playback.
PAIRING
• Press and hold to perform pairing
with Bluetooth device.
*1
is OFF.
4.
Mute
• Silence the unit or restore the sound.
Blink MODE Indicator during Mute.
※
• In the standby mode, press and hold
to switch between APS on and off.
5.
6.
*1
-
VOL + /
• Adjust the listening volume.
The listening volume has a range
※
from 0 to 30 (however, the unit is not
equipped with a display to visually
indicate the volume level). (Default
setting: 10)
Bluetooth Indicator
• Light up Indicate blue when Bluetooth
device is connected.
• Blink during waiting for Bluetooth
connection.
• Blink quickly for Bluetooth pairing.
Refer to page 11 for APS.
English
9
Part names and functions
Back Panel
12
1.
DC IN Jack
Connect the AC adapter.
2.
AUX IN Jack
Connect auxiliary components.
Attaching Rubber feet
Apply the accessory rubber feet to the bottom surface of the unit.
10
Getting started
Turning on
Press
[STANDBY/ON]
This unit switches to the last select mode.
button. The indicator would light.
APS mode
• After this unit is kept inactive for 20 minutes, it automatically switches to the standby mode.
• When 5 minutes before switching to the standby mode automatically, the indicator starts to
blink.
How to turn off the APS mode
• Press and hold
indicator lights red for about 3 seconds.
• If the APS mode is turned on again, Press and hold
and the indicator lights green for about 3 seconds.
Note
• When you play at low volume, this unit might switch to the standby mode automatically.
Please increase the volume, or turn off the APS mode.
[Mute]
to turn off the APS mode in the standby mode and the
button
[Mute]
in the standby mode
button
English
11
Bluetooth Audio playback
Bluetooth wireless technology
This product enables you to enjoy listening to music wirelessly from a Bluetooth wireless
technology enabled device (cell phone, digital music player, etc.).
from a non-Bluetooth wireless technology enabled device using a Bluetooth audio transmitter
available in stores. For details, refer to the user manual for the Bluetooth wireless technology
enabled device.
Note
*1
• The Bluetooth wireless technology enabled device must support A2DP profiles.
• Pioneer does not guarantee proper connection and operation of this unit with all
Bluetooth wireless technology enabled devices.
• The Bluetooth
®
word mark and logos are registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by PIONEER CORPORATION is under license. Other
trademarks and trade names are those of their respective owners.
Pairing this unit and Bluetooth wireless technology device
To enjoy music from a Bluetooth wireless technology enabled device, pairing is required
with this product. Make sure to perform pairing first time you operate the system or any time
pairing data is cleared.
“Pairing” is the step necessary to register Bluetooth wireless technology device to enable
Bluetooth communications. For more details, see also the operating instructions of your
Bluetooth wireless technology device.
• Pairing is required when you first use Bluetooth wireless technology device and this unit.
• To enable Bluetooth communication, pairing should be done with both of your system and
Bluetooth wireless technology device.
enabled device:
Cell phone
Bluetooth wireless technology
enabled device:
Digital music player
Device not equipped with Bluetooth
wireless technology:
Digital music player
+
Bluetooth audio transmitter
(commercially available)
*1
You can also enjoy music
12
Bluetooth Audio playback
1. Press [INPUT] button to select Bluetooth mode.
(Mode Indicator:
green).
2. Press and hold [PAIRING] button until you hear 2 consecutive
“beep” sounds. Then, the blue indicator on the top panel blinks
quickly and the unit will enter the pairing mode.
3. Switch on the Bluetooth wireless technology device that you want
to perform pairing with, place the device within 1 m (3.2 ft.) of the
system, and set it to the pairing mode.
Pairing begins.
• In case of entering PIN code, use “0000”.
( Only “0000” works for PIN code in this product. )
4. When Bluetooth wireless technology device has connected, the blue
indicator on the top panel will change from blinking to lit.
5. Start playback of music contents stored in Bluetooth wireless
technology device.
Connect the Latest Paired Bluetooth wireless technology Device
When the unit is switch on again to Bluetooth mode next time, it will be connected
automatically with equipment that has the latest connected device already.
Connect previous Paired Bluetooth Device
1. If you want to connect other paired device instead of the latest
paired one, please make sure the Bluetooth connection of the latest
device dis-connect. Then, the blue indicator on the top panel blinks
slowly and the unit will change the waiting for connection mode.
*Alternatively, there is also a way to switch the unit in pairing mode.
2. Switch on other paired device, and select this unit from this device
Bluetooth list.
3. Connection with other devices is successful, the blue indicator will
change from blinking to lit.
• Operating range of Bluetooth audio is up to 10 m (32 ft.). (Measured in open space. Walls
and structures may affect range of device.)
English
13
Bluetooth Audio playback
Radio wave caution
This unit uses a 2.4 GHz radio wave frequency, which is a band used by other wireless systems
(see list below). To prevent noise or interrupted communication, do not use this unit nearby
such devices, or make sure these devices are switched off during use.
• Cordless phones
• Cordless facsimiles
• Microwave ovens
• Wireless LAN devices
• Wireless AV equipment
• Wireless controllers for game systems
• Microwave-based health aids
• Some baby monitors
Other, less common, equipment that may operate on the same frequency:
• Anti-theft systems
• Amateur radio stations (HAM)
• Warehouse logistic management systems
• Discrimination systems for train or emergency vehicles
Note
• In the event noise appears in your television image, there is the possibility that a
Bluetooth wireless technology enabled device or this unit (including products supported
by this unit) are causing signal interference with the antenna input connector of your
television, video, satellite tuner, etc. In this event, increase the distance between the
antenna input connector and the Bluetooth wireless technology enabled device or this
unit (including products supported by this unit).
• If there is something obstructing the path between this unit (including devices
supported by this unit) and the device equipped with Bluetooth wireless technology (such
as a metal door, concrete wall, or insulation containing tinfoil), you may need to change
the location of your system to prevent signal noise and interruptions.
14
Bluetooth Audio playback
Scope of operation
Use of this unit is limited to home use. (Transmission distances may be reduced depending
on communication environment).
In the following locations, poor condition or inability to receive radio waves may cause the
audio to be interrupted or stopped:
• In reinforced concrete buildings or steel framed or ironframed buildings.
• Near large metallic furniture.
• In a crowd of people or near a building or obstacle.
• In a location exposed to the magnetic field, static electricity or radio wave interference
from radio communication equipment using the same frequency band (2.4 GHz) as this
unit, such as a 2.4 GHz wireless LAN device or microwave oven.
• If you live in a heavily populated residential area(apartment, townhouse, etc.) and if
your neighbor’s microwave is placed near your system, you may experience radio wave
interference. If this occurs, move your unit to a different place. When the microwave is not
in use, there will be no radio wave interference.
Radio wave reflections
The radio waves received by this unit include the radio wave coming directly from the device
equipped with Bluetooth wireless technology (direct wave) and waves coming from various
directions due to reflections by walls, furniture and building (reflected waves). The reflected
waves (due to obstacles and reflecting objects) further produce a variety of reflected waves
as well as variation in reception condition depending on locations. If the audio cannot be
received properly due to this phenomenon, try moving the location of the device equipped
with Bluetooth wireless technology a little. Also note that audio may be interrupted due to the
reflected waves when a person crosses or approaches the space between this unit and the
device equipped with Bluetooth wireless technology.
English
15
Other Connections
• Before making or changing the connections, switch off the power and disconnect the
power plug from the power outlet.
• When playing music through AUX mode, the music volume will vary depending on the
volume of the music player. If there is distortion when the volume is set at max, lower the
music player’s volume and to avoid distortion.
1. Connecting auxiliary components
Connect the back panel AUX IN jack to your auxiliary playback component.
Digital audio
player, etc.
Stereo mini-plug cable
(commercially available)
This unit’S back panel
2. Press [INPUT] button. (Mode indicator : orange)
3. Start playback of the auxiliary component.
16
Additional Information
Troubleshooting
WARNING
• Never remove the casing of this apparatus.
Incorrect operation is often mistaken for trouble or malfunction. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may
lie in another component. Inspect the other components and electrical appliances being
used. If the trouble cannot be rectified even after checking the points below, ask your nearest
Pioneer authorized service center or your dealer to carry out repair work.
• If the unit does not operate normally due to external effects such as static electricity,
disconnect the power plug from theoutlet and insert it again to return to normal operating
conditions.
Problem Remedy
The power does not turn on. • Disconnect the power plug from the outlet, and
Power automatically switches
to standby without user action.
No sound is output when a
mode is selected.
insert again.
• When no device is connected to the selected the
AUX IN jack and this unit is not operated for 20
minutes or more after AUX mode is selected, power
will automatically turn OFF. (Only when APS mode
(page11) is ON.)
• Make sure the component is connected correctly.
English
17
Additional Information
Problem Remedy
The Bluetooth wireless
technology device cannot be
connected or operated. Sound
from the Bluetooth wireless
technology device is not emitted
or the sound is interrupted.
* The line-of-sight transmission distance is an estimate. Actual transmission distances
supported may differ depending on surrounding conditions.
•
Check that no object that emits electromagnetic
waves in the 2.4 GHz band (microwave oven,
wireless LAN device or Bluetooth wireless
technology apparatus) is near the unit. If such an
object is near the unit, set the unit far from it. Or,
stop using the object emitting the electromagnetic
waves.
Check that the Bluetooth wireless technology device
•
is not too far from the unit and that obstructions are
not set between the Bluetooth wireless technology
device and the unit. Set the Bluetooth wireless
technology device and the unit so that the distance
between them is less than about 10 m* and no
obstructions exist between them.
• The Bluetooth wireless technology device may not
be set to the communication mode supporting the
Bluetooth wireless technology.
Check the setting of the Bluetooth wireless
technology device.
• Check that pairing is correct. The pairing setting
was deleted from this unit or the Bluetooth wireless
technology device. Reset the pairing.
•
Check that the profile is correct. Use a Bluetooth
wireless technology device that supports A2DP
profile.
18
Loading...