Pioneer X-HM16 User Manual

Для моделей X-HM16/X-HM26

Дополнительная информация для клиентов в Российской Федерации Информация о сертификации

X-HM16 X-HM26 X-HM26D

CD Receiver System Micro chaîne CD Sistema receptor de CD Sistema CD con amplificatore CD-Receiversystem CD Receiver System Система ресивера CD

Operating Instructions Mode d’emploi Manual de instrucciones Istruzioni per l’uso Bedienungsanleitung Handleiding Инструкции по эксплуатации

Register your product on/ Enregistrez votre produit sur / Registre su producto en Registrare il proprio prodotto su / Registrieren Sie hier Ihr Produkt / Registreer uw product op / Зарегистрируйте ваше изделие

http://www.pioneer.eu

(Europe / Europe / Europa / Europa / Europa / Europa / Европа)

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

D3-4-2-1-3_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

Operating Environment

Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light) D3-4-2-1-7c*_A1_En

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period. K041_A1_En

CAUTION

This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007.

CLASS 1 LASER PRODUCT

D58-5-2-2a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 25 cm at top, 10 cm at rear, and 5 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

D3-4-2-1-7b*_A1_En

CAUTION

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

D3-4-2-1-1_B1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest our authorized service center or your dealer for a replacement.

S002*_A1_En

CAUTION

The STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-2a*_A1_En

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

K058a_A1_En

Symbol examples

for batteries

Symbol for

equipment

Radio wave caution

This unit uses a 2.4 GHz radio wave frequency, which is a band used by other wireless systems (Microwave ovens and Cordless phones, etc.). In this event noise appears in your television image, there is the possibility this unit (including products supported by this unit) is causing signal interference with the antenna input connector of your television, video, satellite tuner, etc. In this event, increase the distance between the antenna input connector and this unit (including products supported by this unit).

• We are not responsible for any malfunction of the

compatible product due to communication error/malfunctions associated with your network connection and/or your connected equipment. Please contact your Internet service provider or network device manufacturer.

• A separate contract with/payment to an Internet service provider is required to use the Internet.

WARNING

Store small parts out of the reach of children and infants. If accidentally swallowed, contact a doctor immediately.

Thank you for buying this Pioneer product.

Please read through these operating instructions so that you will know how to operate your model properly. After you have finished reading the instructions, put them in a safe place for future reference.

Contents

01 Before you start

What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Loading the batteries in the remote control . . . . . . . . . . . .5

Using the remote control . . . . . . . . . . . . . . . . . . . . . . . 5

02 Part names and functions

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Speaker system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

03 Connections

Speaker connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Using external antennas . . . . . . . . . . . . . . . . . . . . . . 10

Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

04 Getting started

To turn the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Input function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Display brightness control . . . . . . . . . . . . . . . . . . . . . 12

Volume auto set-in. . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Volume control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Sound controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

P.BASS control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

BASS/TREBLE control. . . . . . . . . . . . . . . . . . . . . . . . 13

Setting the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . .13

Calling the wake-up timer . . . . . . . . . . . . . . . . . . . . . 14

Cancelling the wake-up timer. . . . . . . . . . . . . . . . . . . 14

Using the wake-up timer . . . . . . . . . . . . . . . . . . . . . . 14

Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

05 Disc playback

Playing discs or files . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Load the disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Play tracks on a CD . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Play MP3 music files . . . . . . . . . . . . . . . . . . . . . . . . . 15

Advanced CD or MP3 disc playback . . . . . . . . . . . . . . . .16

Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Programmed play (CD) . . . . . . . . . . . . . . . . . . . . . . . 17

About downloading MP3 . . . . . . . . . . . . . . . . . . . . . . 17

Switch the display contents . . . . . . . . . . . . . . . . . . . . 17

06 USB playback

Playing USB storage devices . . . . . . . . . . . . . . . . . . . . .18

Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Switch the display contents . . . . . . . . . . . . . . . . . . . . 19

07 Using the tuner

Listening to FM (For European models)/Listening to FM or

AM (For North American models) . . . . . . . . . . . . . . . . . . 20

Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Saving station presets. . . . . . . . . . . . . . . . . . . . . . . . . 20

Using the Radio Data System (RDS)

(for European models only) . . . . . . . . . . . . . . . . . . . . 21

Listening to the DAB+ (X-HM26D only) . . . . . . . . . . . . . 23

About DAB+ (Digital Audio Broadcasting) . . . . . . . . . 23

Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Changing the information display . . . . . . . . . . . . . . . . 24

Memorising a station. . . . . . . . . . . . . . . . . . . . . . . . . . 24

DAB Frequency table (BAND III) . . . . . . . . . . . . . . . . 24

08 Other connections

Connecting auxiliary components . . . . . . . . . . . . . . . . . . 25

Automatic switching to Audio In input (For North American

models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

09 Bluetooth® Audio playback

Music playback using Bluetooth wireless technology . . . 26

Remote control operation . . . . . . . . . . . . . . . . . . . . . . . . 26

Pairing with the unit (Initial registration) . . . . . . . . . . . . . 26

Listen to music on the unit from a Bluetooth capable device

. . . . . . . . . . . . . . . . . . . . 27

BT STANDBY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Radio wave caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Scope of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Radio wave caution. . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Precautions regarding connections to products supported by this unit

. . . . . . . . . . . . . . . . . 28

10 Additional information

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Playable discs and formats . . . . . . . . . . . . . . . . . . . . . . . 31

Regarding copy protected CDs. . . . . . . . . . . . . . . . . . 32

Supported audio file formats. . . . . . . . . . . . . . . . . . . . 32

Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

When moving this unit. . . . . . . . . . . . . . . . . . . . . . . . . 32

Place of installation. . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Do not place objects on this unit. . . . . . . . . . . . . . . . . 32

About condensation . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Cleaning the product. . . . . . . . . . . . . . . . . . . . . . . . . . 33

Cleaning the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Storing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Cleaning discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

About specially shaped discs . . . . . . . . . . . . . . . . . . . 33

Auto power off setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Restoring all the settings to the defaults . . . . . . . . . . . . . 33

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Before you start 01

English Français Español

Chapter 1:

Before you start

What’s in the box

Please confirm that the following accessories are in the box when you open it.

• Remote Control

• AAA batteries (R03) x 2

• Power cord

• AM antenna cable*1

• FM wire antenna*2

• DAB/FM wire antenna*3

• Warranty card*4

• Operating instructions (this document) *1 North American models only *2 X-HM16/X-HM26 only *3 X-HM26D only *4 European models only

Loading the batteries in the remote control

1 Open the rear lid and load the batteries as illustrated below.

2 Close the rear lid.

CAUTION

• Do not use any batteries other than the ones specified.

Also, do not use a new battery together with an old one.

• When inserting the batteries, make sure not to damage

the springs on the battery’s - terminals. This can cause batteries to leak or over heat.

• When loading the batteries into the remote control, set

them in the proper direction, as indicated by the polarity marks (+ and -).

• Do not heat batteries, disassemble them, or throw them into flames or water.

• Batteries may have different voltages, even if they are the same size and shape. Do not use different types of batteries together.

• To prevent leakage of battery fluid, remove the batteries if you do not plan to use the remote control for a long period of time (1 month or more). If the fluid should leak, wipe it carefully off the inside of the case, then insert new batteries. If a battery should leak and the fluid should get on your skin, flush it off with large quantities of water.

• When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country/area.

WARNING

• Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.

Using the remote control

The remote has a range of about 7 m at an angle of about 30º from the remote sensor.

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the remote and the remote sensor on the unit.

• Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the unit’s remote sensor.

• Remote controllers for different devices can interfere with each other. Avoid using remotes for other equipment located close to this unit.

• Replace the batteries when you notice a fall off in the operating range of the remote.

I NPU

30°

7 m

30°

Part names and functions02

Chapter 2:

Part names and functions

Remote control

1 Í

Switches the receiver between standby and on (page 12).

2 Input function buttons

Use to select the input source to this receiver (page 12).

Use to set up or play the audio file using the Bluetooth network (page 26).

3MENU

Use to access the menu.

4///, ENTER

Use to select/switch system settings and modes, and to confirm actions.

5 PGM/MEMORY

• Use to memory or program the CD (page 17).

• Use to store FM/AM (page 20) or DAB (page 24) stations in memory.

6 Playback control buttons

Use to control each function after you have selected it using the input function buttons (page 16).

TUNE +/–

Use to find radio frequencies (page 20).

PRESET +/–

Use to select preset radio stations (page 20).

7 Sound control buttons

Adjust the sound quality (page 13).

8SLEEP

See Using the sleep timer on page 14.

9TIMER

Use for setting the clock, as well as for setting and checking the timers (page 12).

Press to change the repeat play setting from a CD (page 16) or USB (page 19).

11 RANDOM

Press to randomize order play setting from a CD (page 16) or USB (page 19).

12 DISPLAY

Press to change the display for MP3 (page 17), RDS (page 21) or DAB (page 24) information.

Press to return to the previous display.

14 Volume control buttons

Use to set the listening volume (page 12).

Mutes/unmutes the sound (page 12).

16 DIMMER

Dims or brightens the display. The brightness can be controlled in four steps (page 12).

8 9

15 16

Part names and functions 02

English Français Español

Front panel

1Í STANDBY/ON

Switches the receiver between standby and on (page 12).

2 Remote sensor

Receives the signals from the remote control.

3 TIMER indicator

Lights when the receiver is power off with timer setting.

4 Main display

See Display on page 8.

5 Volume control

Use to set the listening volume (page 12).

6INPUT

Selects the input source.

7 Headphone socket

Use to connect headphones. When the headphones are connected, there is no sound output from the speakers.

8USB terminal

Use to connect your USB mass storage device as an audio source (page 18).

9 Disc tray

Place the disc, label side up (page 15).

10 Playback control buttons

Selects the desired track or file to be played back. Use to stop the playback. Stops playback or resumes playback from the pause point.

11 Disc tray open/close button

Use to open or close the disc tray (page 15).

TIMER

1 3 4 52

76 8 9 10 11

Part names and functions02

Display

Lights when the sound is muted.

Note

• The mute icon will be displayed in red.

Start playback.

;

Pause playback.

Timer function is set.

5 Character display

Displays various system information.

Speaker system

1 Tweeter 2 Woofer 3 Bass Reflex Duct

Important

• Speaker grille cannot be removed.

• Both speakers can be used on either the right or the left side.



11234

Connections 03

English Français Español

Chapter 3:

Connections

CAUTION

• Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.

• Connect the power cord after all the connections between devices have been completed.

Speaker connection

• Push open the tabs and insert exposed wire.

• Connect the black wire to (s) terminal, and the red wire to the (r) terminal.

CAUTION

• These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts.

• Do not connect any speakers other than those supplied to this system.

• Do not connect the supplied speakers to any amplifier other than the one supplied with this system. Connection to any other amplifier may result in malfunction or fire.

• Do not attach these speakers to the wall or ceiling. They may fall off and cause injury.

• These speakers are magnetically shielded. However, depending on the installation location, color distortion may occur if the speaker system is installed extremely close to the screen of a television set. If this happens, turn off the television set, and then turn it on after 15 to 30 minutes. If the problem persists, move the speaker system away from the television set.

• Make sure that the speaker cable cores do not become exposed and make contact with other cable cores. This may cause malfunction of the product.

• Do not allow the speaker cable core to come into contact with the receiver body.

• If the speaker cable core comes into contact with any metal portion of the receiver’s body, it may damage the speakers and cause smoke and fire. Insert speaker cables securely into the terminals and check that the cable does not come out of easily.

Note

• There is no difference between L and R speakers.

Left

speaker

Right speaker

This unit’s rear panel

Connections03

Connecting antennas

• Connect the AM loop antenna and the FM (DAB/FM) wire antenna as shown below.

• To improve reception and sound quality, connect external antennas (see Using external antennas).

For North American models only

For European models

1 Connect the AM antenna wires.

Holding the connector to connect.

2 Fix the AM loop antenna to the attached stand.

Set up as illustrated above.

3 Place the AM antenna on a flat surface and in a direction giving the best reception.

• Place the antenna near a window, etc. for the best reception.

• Do not place the antenna near a computer or TV. It may result in noise.

4 Connect the FM (DAB/FM) wire antenna into the FM antenna socket.

For best results, extend the FM (DAB/FM) antenna fully and fix to a wall or door frame. Don’t drape loosely or leave coiled up.

Using external antennas

To improve FM reception

Use a PAL connector (not supplied) to connect an external FM (DAB/FM) antenna.

X-HM16/X-HM26

X-HM26D

X-HM16/ X-HM26

X-HM26D

One-touch PAL connector

75 Ωcoaxial cable

Connections 03

English Français Español

Plugging in

Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet. After you’ve finished making all connections, plug the unit into an AC outlet.

CAUTION

• Do not use any power cord other than the one supplied with this unit.

• Do not use the supplied power cord for any purpose other than that described above.

To AC outlet

This unit’s rear panel

Power cord

Getting started04

Chapter 4:

Getting started

To turn the power on

Press the Í to turn the power on.

After use:

Press the Í to enter the power stand-by mode.

Setting the clock

1 Press Í to turn the power on.

2 Press TIMER on the remote control.

“CLOCK” is shown on the main display.

3 Press ENTER. 4 Press



/  to set the day, then press

ENTER. 5 Press



/  to set the hour, then press

ENTER. 6 Press



/  to set the minute, then press

ENTER to confirm. 7 Press ENTER.

To confirm the time display:

Press the TIMER. The time display will appear for about 10 seconds.

To readjust the clock:

Perform “Setting the clock” from step 1.

Note

• When power supply is restored after unit is plugged in again or after a power failure, reset the clock.

General control

Input function

When the INPUT on main unit is pressed, the current function will change to different mode. Press the INPUT repeatedly to select desired function.

*1 X-HM26D only *2 North American models only

Display brightness control

Press DIMMER to dims the display brightness. The brightness can be controlled in four steps.

Volume auto set-in

If you turn off and on the main unit with the volume set to 31 or higher, the volume starts at 30 and sets in to the last set level.

Volume control

Turn the volume knob towards VOLUME (on main unit) or press VOL +/– (on remote control) to increase or decrease the volume.

CAUTION

• The sound level at a given volume setting depends on speaker efficiency, location, and various other factors. It is advisable to avoid exposure to high volume levels. Do not turn the volume on to full at switch on. Listen to music at moderate levels. Excessive sound pressure from earphones and headphones can cause hearing loss.

Muting

The volume is muted temporarily when pressing the on the remote control. Press again to restore the volume.

Bluetooth DAB

udio In FMUSB

Getting started 04

English Français Español

Sound controls

Equalizer

When the EQ is pressed, the current mode setting will be displayed. To change to a different mode, press the EQ repeatedly until the desired sound mode appears.

P.BASS control

When the power is first turned on, the unit will enter the P.bass mode which emphasises the bass frequencies. To cancel the P.bass mode, press the P.BASS on the remote control.

BASS/TREBLE control

Press the SOUND to select “BASS” or “TREBLE”, then press



/  to adjust the bass or treble.

Note

• The EQ and P.BASS cannot operate simultaneously.

The most recently selected of these two functions will be the one used.

• SOUND can operate alongside either the EQ or

P.BASS.

When one of the above two functions is selected, the function that is not selected will be displayed as follows.

1 When P.BASS setting (ON/OFF) is changed

• EQ : FLAT

2 When EQ setting is changed

• P.BASS : OFF

Setting the wake-up timer

Used to change the existing timer setting, or to set a new timer.

1 Press Í to turn the power on.

2 Press and hold TIMER on the remote control.

3 Press



/  to select “ONCE” or “DAILY”,

then press ENTER.

ONCE – Once timer play works for one time only at a

preset time. DAILY – Daily timer play works at the same preset time

and days of week.

4 Press  /  to select “TIMER SET”, then press ENTER.

5 Press



/  to select the timer playback

source, then press ENTER.

CD, DAB (X-HM26D only), FM, AM (North American models only) and USB can be selected as the playback source.

6 Press  /  to select the timer day, then press ENTER.

7 Press



/  to set the hour, then press

ENTER. 8 Press



/  to set the minute, then press

ENTER.

Set the time to finish as in steps 7 and 8 above.

9 Adjust the volume press VOL +/– , then press ENTER.

“ ” appears on the display.

10 Press Í to enter the power standby mode.

The TIMER indicator lights up.

NIGHT

FLAT A flat and basic sound

ACTIVE

DIALOGUE

A sound that can be enjoyed at night even with lower volume

A powerful sound that emphasizes low and high tones

A sound that allows the radio or vocals to be heard more easily

Getting started04

Calling the wake-up timer

It can be used to re-use an existing timer setting.

1 As well as steps 1 through 3 in “Setting the wake-up timer”.

2 Press



/  to select “TIMER ON”, then

press ENTER.

Cancelling the wake-up timer

It can be used to turn off the timer setting.

1 As well as steps 1 through 3 in “Setting the wake-up timer”.

2 Press



/  to select “TIMER OFF”, then

press ENTER.

Using the wake-up timer

1 Press Í to turn the power off.

2 At the wake-up time, this unit will turn on automatically and play the selected input function.

Note

• If at the wake-up time the USB storage device is not connected to this unit or a disc is not inserted, this unit will be turned to on and not play back the track.

• Some discs may not be played automatically at the wake-up time.

• If you set the timer, take one minute or more between the start and end time.

Using the sleep timer

The sleep timer switches off the unit after a specified time so you can fall asleep without worrying about it.

1 Press SLEEP repeatedly to select a switch off time.

Choose between 10 min, 20 min, 30 min, 60 min, 90 min, 120 min, 150 min, 180 min or OFF. The newly set value displays for 3 seconds, and then the setting is completed.

Note

• The sleep timer can be set by pressing SLEEP while the remaining time is displayed.

Using Headphones

Connect to the jack plug of the headphones. When the headphones are connected, there is no sound

output from the speakers.

• Do not turn the volume on to full at switch on and listen to music at moderate levels. Excessive sound pressure from earphones and headphones can cause hearing loss.

• Before plugging in or unplugging the headphone, reduce the volume.

• Be sure your headphone has a 3.5 mm diameter plug and impedance between 16

and 50 Ω. The

recommended impedance is 32

TIMER

Disc playback 05

English Français Español

Chapter 5:

Disc playback

This system can play back a standard CD, CD-R/RW in the CD format and CD-R/RW with MP3 files, but cannot record on them. Some audio CD-R and CD-RW discs may not be playable due to the state of the disc or the device that was used for recording.

• For details about MP3, see page 31.

Playing discs or files

Load the disc

1 Press Í to turn the power on. 2 Press CD on the remote control or INPUT

repeatedly on the main unit to select CD input. 3 Press < on the main unit to open the disc tray. 4 Place the disc on the disc tray, label side up.

5 Press

on the main unit to close the disc

tray.

Play tracks on a CD

1 When the recognition is completed, press

After the last track is played, the unit will stop automatically.

Play MP3 music files

MP3 track data is called “music file” and the location they are stored is called a “folder” in this document.

1 When the recognition is completed, press

/

to select the folder where the music file is

stored ([ ]), then press



or ENTER.

• Repeat this step if there are other folders inside the selected folder.

• To return to the previous folder, press



or .

2 Press / to select the music file ([ ]), and then press

or ENTER.

• Once play starts, only music files inside the same folder can be played continuously.

CAUTION

• Do not place two discs in one disc tray.

• Do not play discs of special shapes (heart, octagon, etc). It may cause malfunctions.

• Do not push the disc tray whilst it is moving.

• If the power fails whilst the tray is open, wait until the power is restored.

• Be sure to place 8 cm disc in the middle of the disc tray.

Note

• Due to the structure of the disc information, it takes longer to read an MP3 disc than a normal CD (approximately 20 to 90 seconds).

• When the beginning of the first track is reached during fast reverse, the unit will enter the playback mode (only for CD).

• If TV or radio interference occurs during CD operation, move the unit away from the TV or radio.

Tip

• When no operation has done in CD mode and the audio file is not played for more than 20 minutes, the power will automatically turn off. In this case it is required that the Auto power off is switched to ON.

• Auto power off can be switched to ON/OFF (page 33).

e.g.,

Disc playback05

Basic operations

Advanced CD or MP3 disc playback

Repeat play

Repeat play can play one track, all tracks or a programmed sequence continuously.

To repeat one track:

Press repeatedly until “REPEAT ONE” appears. Press

ENTER.

To repeat all tracks:

Press repeatedly until “REPEAT ALL” appears. Press

ENTER.

To repeat desired tracks:

Perform steps 1 - 5 in “Programmed play (CD)” section (page 17) and then press repeatedly until “REPEAT

ALL” appears. Press ENTER.

To cancel repeat play:

Press repeatedly until “REPEAT OFF” appears. Press

ENTER.

Note

• After performing repeat play, be sure to press ∫. Otherwise, the disc will play continuously.

• During repeat play, random play is not possible.

Random play

The tracks on the disc can be played in random order automatically.

To random play all tracks:

Press RANDOM repeatedly until “RANDOM ON” appears. Press ENTER.

To cancel random play:

Press RANDOM repeatedly until “RANDOM OFF” appears. Press ENTER.

Note

• If you press the 9 during random play, you can move to the track selected next by the random operation.

• In random play, the unit will select and play tracks automatically. (You cannot select the order of the tracks.)

• During random play, repeat play is not possible.

Function Main unit Remote

control

Operation

Play

Press in the stop mode.

Stop

Press in the playback mode.

(when playing a CD) “RESUME” is displayed and the place where you stopped play is memorized. Press again and the memorized position is cleared.

Pause

Press in the playback mode. Press

to resume playback from the paused point.

Track up/ down

Press in the playback or stop mode. If you press the button in the stop mode, press

to start the desired

track.

(when playing MP3) You can only skip forward or back to music files inside the same folder.

Fast forward/ reverse

Press and hold down in the playback mode.

Release the button to resume playback.

Disc playback 05

English Français Español

Programmed play (CD)

You can choose up to 24 selections for playback in the order you like.

1 Whilst in the stop mode, press PGM/ MEMORY on the remote control to enter the programming save mode.

2 Press

: 9

to select the desired tracks. 3 Press ENTER to save track number. 4 Repeat steps 2 - 3 for other tracks. Up to 24

tracks can be programmed.

• If you want to check the programmed tracks, press

PGM/MEMORY.

• If you make a mistake, the last programmed tracks will be canceled by pressing .

5 Press 1; to start playback. To cancel the programmed play mode:

To cancel the programmed play, press twice ∫ on the remote control. The display will show “PRG CLEAR” and all the programmed contents will be cleared.

Adding tracks to the program:

Press the PGM/MEMORY. Then follow steps 2 - 3 to add tracks.

Note

• When a disc is ejected, the program is automatically cancelled.

• If you press the Í to enter the standby mode or change the function from CD to another, the programmed selections will be cleared.

• During the program operation, random play is not possible.

About downloading MP3

There are many music sites on the internet that you can download MP3 music files. Follow the instructions from the website on how to download the music files. You can then play back these downloaded music files by burning them to a CD-R/RW disc.

• Your downloaded song/files are for personal use only. Any other usage of the song without owner’s permission, is against the law.

Switch the display contents

1 Press DISPLAY during playback.

If the title, artist and album name has been written to the file, that information will be displayed. (You can view this unit is only alphanumeric characters. Non- alphanumeric character are displayed in the “∫”.)

Note

• “Not supported playback file” can not be playback. In this case, will be skipped automatically.

• There may be cases where no information can be displayed.

• Displaying title, artist, and albums is only supported with ID3 Version 1 (1.0 or 1.1).

Title display

Number of the track, title display

Artist display

Album display

Number of the track in a folder, playback time display

Number of the track in a folder, remaining time display

USB playback06

Chapter 6:

USB playback

Playing USB storage devices

It is possible to listen to two-channel audio using the USB interface with MP3 files on the front of this receiver.

• Pioneer does not guarantee that any file recorded on a USB storage device will play or that power will be supplied to a USB storage device. Also note that Pioneer will accept no responsibility whatsoever for loss of files on USB storage devices caused by connection to this unit.

• For details about MP3, see page 31.

1 Press USB as the input source.

“USB” is shown on the main display.

2 Connect the USB storage device.

• This receiver does not support a USB hub.

3 When the recognition is completed, press

/

to select the folder where the music file is

stored ([ ]), then press



or ENTER.

• MP3 track data is called “music file” and the location they are stored is called a “folder” in this document.

• Repeat this step if there are other folders inside the selected folder.

• To return to the previous folder, press



or .

4 Press / to select the music file ([ ]), and then press

or ENTER.

• Once play starts, only music files inside the same folder can be played continuously.

• For details about the basic operations, see page 16.

• When changing to a different input source, stop the USB memory playback first, before changing.

• Turn the power off before removing the USB storage device.

Note

• This unit may not recognize a USB storage device, play files or supply power to a USB storage device. For details, see

When a USB storage device is connected

on page 30.

• When a USB storage device is not playing and the unit has not been operated for 20 minutes or more, the power will automatically turn off. In this case it is required that the Auto power off is switched to

(page 33).

TIMER

USB storage device

(commercially available)

USB playback 06

English

Français Español

Repeat play

Repeat play can play one track, all tracks or a programmed sequence continuously.

To repeat one track:

Press repeatedly until “REPEAT ONE” appears. Press

ENTER.

To repeat all tracks:

Press repeatedly until “REPEAT ALL” appears. Press

ENTER.

To cancel repeat play:

Press repeatedly until “REPEAT OFF” appears. Press

ENTER.

Note

• After performing repeat play, be sure to press ∫. Otherwise, the file of USB storage device will play continuously.

• During repeat play, random play is not possible.

Random play

The file of USB storage device can be played in random order automatically.

To random play all tracks:

Press RANDOM repeatedly until “RANDOM ON” appears. Press ENTER.

To cancel random play:

Press RANDOM repeatedly until “RANDOM OFF” appears. Press ENTER.

Note

• If you press the 9 during random play, you can move to the track selected next by the random operation.

• In random play, the unit will select and play tracks automatically. (You cannot select the order of the tracks.)

• During random play, repeat play is not possible.

Switch the display contents

This unit can switch the information recorded in the USB storage device. For details, see Switch the display contents on page 17.

Using the tuner07

Chapter 7:

Using the tuner

Listening to FM (For European models)/Listening to FM or AM (For North American models)

The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and manual (step) tuning functions. Once you are tuned to a station you can memorize the frequency for recall later. See Saving station presets below for more on how to do this.

Tuning

1 Press the Í to turn the power on.

2 Press TUNER repeatedly to select desired frequency band (FM or AM).

• (X-HM26D) You can select “FM” and “DAB”. For details about “DAB”, see page 23.

3 Press TUNE +/– on the remote control to tune in to the desired station.

Automatic tuning:

Press and hold TUNE +/–, scanning will start automatically and the tuner will stop at the first receivable broadcast station.

Manual tuning:

Press the TUNE +/– repeatedly to tune in to the desired station.

Note

• When radio interference occurs, automatic tuning may stop automatically at that point.

• Automatic tuning will skip weak signal stations.

• To stop the automatic tuning, press ∫.

• When an RDS (Radio Data System) station is tuned in, the frequency will be displayed first. Finally, the station name will appear.

• Full auto tuning can be achieved for RDS stations using Auto Station Program Memory (ASPM) mode, see page 22.

To receive an FM stereo transmission:

1 Press TUNER until “FM” appears on the display. 2 Press MENU and then press / until “FM STEREO/ MONO” appears on the display. 3 Press ENTER and then press / until “AUTO” appears on the display.

Improving poor FM reception:

After performing the above steps 1 - 2, press ENTER and then press / until “MONO” appears on the display.

This will change the tuner from stereo to mono and usually improve the reception.

Saving station presets

If you often listen to a particular radio station, it’s convenient to have the receiver store the frequency for easy recall whenever you want to listen to that station (Preset tuning). This saves the effort of manually tuning in each time. This unit can memorize up to 45 stations.

(FM 30 stations/AM 15 stations)

1 Tune to a station you want to memorize.

See Tuning above for more on this.

2 Press PGM/MEMORY.

The preset number will flash.

3 Press PRESET +/– to select the preset channel number.

4 Press PGM/MEMORY to store that station in memory.

If the preset number has changed from flashing to lighting, before the station is memorised, repeat the operation from step 2.

• Repeat steps 1 - 4 to set other stations, or to change a preset station. When a new station is stored in the memory, the station previously memorised for that preset channel number will be erased.

Using the tuner 07

English Français Español

Note

• The backup function protects the memorised stations for a few hours should there be a power failure or the AC power cord become disconnected.

To recall a memorised station

Press PRESET +/– to select the desired station.

To scan the preset stations

The stations saved in the memory can be scanned automatically. (Preset memory scan)

1 Press and hold PRESET +/–. The preset number will appear and the programmed stations will be tuned in sequentially, for 5 seconds each.

2 Press PRESET +/– again when the desired station is located.

To erase entire preset memory

1 Press TUNER on the remote control. 2 Press and hold until “MEMORY CLEAR” appears.

Note

• All stations will be erased.

Using the Radio Data System (RDS) (for European models only)

Radio Data System (RDS) is a system used by most FM radio stations to provide listeners with various kinds of information—the name of the station and the kind of show they’re broadcasting, for example.

One feature of RDS is that you can search by type of program. For example, you can search for a station that’s broadcasting a show with the program type, Jazz Music.

Information provided by RDS

1 Press TUNER until “FM” appears on the display. 2 Press DISPLAY repeatedly. Each time the DISPLAY is pressed, the display will switch as follows:

• When tuning in to a station other than an RDS station or to an RDS station which sends weak signal, the display will change in the following order:

Search for stations by Program Type

1Press TUNER until “FM” appears on the display. 2Press MENU and then press / until “FM RDS” appears on the display. 3Press ENTER and then press / until “PTY” appears on the display. 4Press ENTER. “SELECT” will appear for about 5 seconds.

5Press / to select the program type you want to hear. Each time the button is pressed, the program type will appear. If the button is held down, the program type will appear continuously.

6 Whilst the selected program type is displayed (within 5 seconds), press ENTER. After the selected program type has been lit for 2 seconds, “SEARCH” will appear, and the search operation will start.

The Program Types displayed are as follows:

• If the display has stopped flashing, start again from step

2. If the unit finds a desired program type, the corresponding channel number will lit for about 8 seconds, and then the station name will remain it.

• If you want to listen to the same program type of another station, repeat steps 2 - 6. The unit will look for the next station.

• If no station can be found, “NOT FOUND” will appear for 4 seconds.

Station name (PS) Programme type (PTY)

Frequency Radio text (RT)

NO RDS

FM 98.80 MHz

News

– News

Current Affairs

– Current

Affairs

Information

– General

Information

Sport

– Sport

Education

– Educational

Drama

– Radio plays, etc.

Cultures

– National or regional

culture, theater, etc.

Science

– Science and

technology

Varied Speech

– Usually talkbased material, such as quiz shows or interviews.

Pop Music

– Pop music

Rock Music

– Rock music

Easy Listening

– Easy listening

Light Classics M

– ‘Light’

classical music

Serious Classics

– ‘Serious’

classical music

Other Music

– Music not fitting

above categories

Weather & Metr

– Weather

reports

Finance

– Stock market reports,

commerce, trading, etc.

Children’s Progs

– Programs

for children

Social Affairs

– Social affairs

Religion

– Programs

concerning religion

Phone In

– Public expressing

their views by Phone

Travel & Touring

– Holidaytype travel rather than traffic announcements

Leisure & Hobby

– Leisure

interests and hobbies

Jazz Music

– Jazz

Country Music

– Country

music

National Music

– Popular music in a language other than English

Oldies Music

– Popular music

from the ‘50s and’ 60s

Folk Music

– Folk music

Documentary

– Documentary

Alarm Test

– Broadcasting when testing emergency broadcast equipment or receivers.

Alarm - Alarm!

– Emergency announcement made under exceptional circumstances to give warning of events causing danger of a general nature.

Using the tuner07

Using the Auto Station program Memory (ASPM)

Whilst in the ASPM operation mode, the tuner will automatically search for new RDS stations. Up to 30 stations can be stored.

If you have already stored some stations in memory, the number of new stations you can store will be less.

1 Press TUNER until “FM” appears on the display. 2 Press MENU and then press / until “FM RDS” appears on the display. 3 Press ENTER and then press / until “ASPM” appears on the display. 4 Press ENTER. After “ASPM” has flashed for about 4 seconds, scanning will start (87.5 - 108 MHz).

After scanning, the number of stations stored in memory will be displayed for 4 seconds, and then “END” will appear for 4 seconds.

• To stop the ASPM operation before it is complete: Press ∫ whilst it is scanning for stations. The stations which are already stored in memory will be kept there.

• If the same station is broadcasting on different frequencies, the strongest frequency will be stored in memory.

• Any station which has the same frequency as the one stored in memory will not be stored.

• If 30 stations have already been stored in memory, the scan will be aborted. If you want to redo the ASPM operation, erase the preset memory.

• If no station have been stored in memory, “NOT FOUND” will appear for about 5 seconds.

• If the RDS signals are very weak, station names may not be stored in memory.

• The same station name can be stored in different channels.

• In a certain area or during certain time periods, the station names may temporarily be different.

Note

• If any of the following events occur, it does not mean that the unit is faulty:

- “PS”, “NO PS” and a station name appear alternately,

and properly.

- If a particular station is not broadcasting properly or a

station is conducting tests, the RDS reception function may not work properly.

- When you receive an RDS station whose signal is too

weak, information like the station name may not be displayed.

- “NO PS”, “NO PTY” or “NO RT” will flash for about 5

seconds, and then the frequency will be displayed.

• Notes for radio text:

- The first 8 characters of the radio text will appear and

then they will scroll across the display.

- If you tune in to an RDS station which is not

broadcasting any radio text, “NO RT” will be displayed when you switch to the radio text position.

- Whilst radio text data is received or when the text

contents change, “RT” will be displayed.

Using the tuner 07

English Français Español

Listening to the DAB+ (X-HM26D only)

About DAB+ (Digital Audio Broadcasting)

Digital Audio Broadcasting is a digital transmission system where audio signals are converted to digital signals for broadcasting. DAB+ is broadcast as a group of data called multiplex (ensemble) which may contain one or more stations (services). Each station contains a primary service and there may be one or more secondary services. This allows several programmes or services to be transmitted on a single frequency.

Tuning

1 Press the TUNER until “DAB” appears on the display.

When turned on for the first time, the unit scans radio stations automatically to create a station list.

The stations will be stored in alphanumeric order and the first station on the list will be selected and you will hear it through the speakers.

2 Press the TUNE +/– to select the desired station.

3 Within 10 seconds, press the ENTER on the remote control to tune into the desired station.

• If no station is found, “NO SIGNAL” appears.

• Up to 100 appears for total received stations.

Auto Scan

You can make the auto scan again when you move the unit to other areas or add multiplex channels to the station list.

1 Press the TUNER until “DAB” appears on the display. 2Press MENU and then press / until “DAB SCAN” appears on the display. 3Press ENTER and then press / until “AUTO” appears on the display. 4Press ENTER. Auto Scan scanning begins.

After the scanning process is complete, the first station that was detected is selected.

Manual tune

You can manually store stations which Auto Scan cannot find. If reception is poor, you can adjust the sensitivity. Manual tune is only available after Auto tune. Perform Auto Scan first.

1 Press the TUNER until “DAB” appears on the display. 2Press MENU and then press / until “DAB SCAN” appears on the display. 3Press ENTER and then press / until “MANUAL” appears on the display. 4Press ENTER. 5 Within 10 seconds, press the TUNE +/– to select the DAB+ frequency. 6 Within 10 seconds, press the ENTER.

• If the level is too low, move the aerial or unit to improve reception.

DAB + SIGNAL

MULTIPLEX (ENSEMBLE)

SERVICES

SERVICES COMPONENTS (STATIONS)

Using the tuner07

Changing the information display

You can switch DAB+ display information. Press the DISPLAY button. Each time the button is pressed, the information display

changes in the following order. When “NO SIGNAL” appears, the DISPLAY button does not

allow you to change the display.

[Programme Name]

Station name is displayed. (set by default)

[Scrolling text]

Information scrolls across the display when sent from the station.

[Programe type]

A description of the type of content being broadcast by the station.

[Multiplex name]

The name of the multiplex (ensemble) which provides the current service.

[Frequency]

The DAB+ frequency for the station.

[Stereo mode]

Display stereo mode.

[Transfer speed]

The data transfer speed.

[Signal quality]

The signal quality is displayed as a number (0 - 100). [85-100: Good, 70-84: Fair, 0-69: Poor]

Memorising a station

You can store 10 DAB stations in memory and recall them at the push of a button. (Preset tuning)

1 Tune to the desired DAB station.

2 Press the PGM/MEMORY.

The preset number will flash.

3 Within 10 seconds, press the PRESET +/– to select the preset channel number.

Store the stations in memory, in order, starting with preset channel 1.

4 Within 10 seconds, press the PGM/ MEMORY to store that station in memory.

If the preset number indicators disappear before the station is memorised, repeat the operation from step 2.

5 Repeat steps 1 - 4 to set other stations, or to change a preset station.

When a new station is stored in the memory, the station previously memorised for that preset channel number will be erased.

DAB Frequency table (BAND III)

Frequency Label Frequency Label

174.928 MHz 5A 208.064 MHz 9D

176.640 MHz 5B 209.936 MHz 10A

178.352 MHz 5C 211.648 MHz 10B

180.064 MHz 5D 213.360 MHz 10C

181.936 MHz 6A 215.072 MHz 10D

183.648 MHz 6B 216.928 MHz 11A

185.360 MHz 6C 218.640 MHz 11B

187.072 MHz 6D 220.352 MHz 11C

188.928 MHz 7A 222.064 MHz 11D

190.640 MHz 7B 223.936 MHz 12A

192.352 MHz 7C 225.648 MHz 12B

194.064 MHz 7D 227.360 MHz 12C

195.936 MHz 8A 229.072 MHz 12D

197.648 MHz 8B 230.784 MHz 13A

199.360 MHz 8C 232.496 MHz 13B

201.072 MHz 8D 234.208 MHz 13C

202.928 MHz 9A 235.776 MHz 13D

204.640 MHz 9B 237.488 MHz 13E

206.352 MHz 9C 239.200 MHz 13F

Other connections 08

English Français Español

Chapter 8:

Other connections

CAUTION

• Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.

• We will not accept responsibility for damage arising from the connection of equipment manufactured by other companies.

Connecting auxiliary components

Connect your auxiliary playback component using the

AUDIO IN input on the rear panel.

1 Press AUDIO as the input source.

When AUDIO IN is selected, “Audio In” is displayed on the main display.

Note

• If the

AUDIO IN

mini-plug jack is connected to auxiliary phones jack, the volume of the unit will be adjusted by the volume on the playback component. If the sound is distorted after you lower the volume of the unit, try lowering the volume on the auxiliary playback component.

Automatic switching to Audio In input (For North American models only)

This function automatically switches to "AUDIO IN" when there is audio input to the AUDIO IN jack.

1 Press MENU and then press / until “Audio In detect” appears on the display.

2 Press ENTER and then press

/

to switch

Audio In detect ON/OFF.

• It is set to OFF in the factory setting.

Note

• When the Audio In detect is ON, “Audio In Det ON” is

displayed on the main display.

• When the Audio In detect is OFF, “Audio In Det OFF”

is displayed on the main display.

Portable audio player, etc.

3.5 mm stereo miniplug cable (commercially available)

Bluetooth® Audio playback

Chapter 9:

Bluetooth

Audio playback

X-HM26/26D only

Music playback using Bluetooth wireless technology

The unit is capable of playing back music stored on Bluetooth capable devices (cell phones, digital music players etc.) wirelessly. You can also use a Bluetooth audio transmitter (sold separately) to enjoy music from devices that do not have Bluetooth functionality. Please refer to the user’s manual for your Bluetooth capable device for more details.

Note

• The Bluetooth

word mark and logos are registered

trademarks owned by the Bluetooth SIG, Inc.

• The Bluetooth wireless technology enabled device must support A2DP profiles.

• Connection is not always guaranteed with all Bluetoothenabled devices.

Remote control operation

The remote control supplied with this unit allows you to play and stop media, and perform other operations.

Note

• The Bluetooth wireless technology enabled device must support AVRCP profiles.

• Remote control operations cannot be guaranteed for all Bluetooth wireless technology enabled devices.

Pairing with the unit (Initial registration)

In order for the unit to playback music stored on a Bluetooth capable device, pairing must first be performed. Pairing should be performed when first using the unit with the Bluetooth capable device, or when the pairing data on the device has been erased for any reason. Pairing is a step required to allow communication using Bluetooth wireless technology to be carried out.

• Pairing is only performed the first time that you use the unit and the Bluetooth capable device together.

• In order to allow communication using Bluetooth wireless technology to take place, pairing must be performed on both the unit and the Bluetooth capable device.

• After pressing the and switching to Bluetooth input, perform the pairing procedure on the Bluetooth capable device. If pairing has been performed correctly, you will not need to perform the pairing procedures for the unit as shown below.

Please refer to the user’s manual for your Bluetooth capable device for more details.

1 Press the Í and turn the power to the unit on.

2 Press the .

The unit switches to Bluetooth and “Pairing” will be displayed.

3 Turn on the power to the Bluetooth capable device that you wish to pair with, and perform pairing procedure on it.

TIMER

Bluetooth

wireless technology

enabled device:

Cell phone

Bluetooth

wireless technology

enabled device:

Digital music player

Device not equipped with

Bluetooth

wireless technology:

Digital music player

Bluetooth

audio transmitter

(commercially available)

Music data

Bluetooth® Audio playback

English Français Español

Note

• This unit will be displayed as “Pioneer X-HM26” on all Bluetooth capable devices that you have.

Pairing will start.

• Place the Bluetooth capable device close to the unit.

• Please refer to the user’s manual for your Bluetooth capable device for details on when pairing can be performed and the procedures required for pairing.

• When PIN code entry is requested, enter “0000.” (This unit does not accept any PIN code setting other than “0000.”)

4 Confirm on the Bluetooth capable device that pairing has been completed.

If pairing with the Bluetooth capable device has been completed correctly, the name of the Bluetooth capable device will be displayed on the front panel of the unit. (Only single-byte alphanumeric characters can be displayed. Any character that cannot be displayed will be indicated by a “∫”.)

Listen to music on the unit from a Bluetooth capable device

1 Press the .

The unit will switch to Bluetooth input.

2A Bluetooth connection will be created between the Bluetooth capable device and the unit.

Procedures for connecting to the unit should be performed from the Bluetooth capable device.

• Please refer to the user’s manual for your Bluetooth capable device for details of the connection procedures.

3 Playback music from the Bluetooth capable device.

Note

• When Bluetooth capable devise is not connected and no operations have been performed for more than 20 minutes, the unit will automatically power off. In this case it is required that the Auto power off is switched to ON.

• Auto power off can be switched to ON/OFF (page 33).

BT STANDBY

• The following can be done when the unit is on standby

with the BT STANDBY switched ON.

• By selecting a Bluetooth capable device that already has a connection history (pairing has already been conducted) with this unit, this unit will automatically turn on with the Bluetooth function.

BT STANDBY settings

1 Press the .

2 Press MENU and then press / until “BT STANDBY” appears on the display.

3 Press ENTER and then press

/

to switch

BT STANDBY ON/OFF.

• It is set to OFF in the factory setting.

Note

• When the BT STANDBY is ON, “BT STANDBY ON” is displayed on the main display.

• When the BT STANDBY is OFF, “BT STANDBY OFF” is displayed on the main display.

Connection while in BT STANDBY mode with Bluetooth capable device

When connection history (pairing has already been conducted) with a Bluetooth capable device exists for the unit during BT STANDBY, the unit can receive a connection request directly from the connection history.

The unit will start using the Bluetooth function, and connect with a Bluetooth capable device.

Even devices that have already been paired with this unit will not connect during BT STANDBY in the following cases.

In such cases, delete pairing history from the Bluetooth wireless technology device and perform pairing again.

• This unit can store a maximum of 8 units in the pairing history.

• If the settings are reset to the factory setting, all pairing history will be deleted.

Bluetooth® Audio playback

Radio wave caution

This unit uses a 2.4 GHz radio wave frequency, which is a band used by other wireless systems (see list below). To prevent noise or interrupted communication, do not use this unit nearby such devices, or make sure these devices are switched off during use.

• Cordless phones

• Cordless facsimiles

• Microwave ovens

• Wireless LAN devices (IEEE802.11b/g)

• Wireless AV equipment

• Wireless controllers for game systems

• Microwave-based health aids

• Some baby monitors Other, less common, equipment that may operate on the same frequency:

• Anti-theft systems

• Amateur radio stations (HAM)

• Warehouse logistic management systems

• Discrimination systems for train or emergency vehicles

Note

• In the event noise appears in your television image,

there is the possibility that a Bluetooth wireless technology enabled device or this unit (including products supported by this unit) are causing signal interference with the antenna input connector of your television, video, satellite tuner, etc. In this event, increase the distance between the antenna input connector and the Bluetooth wireless technology enabled device or this unit (including products supported by this unit).

• If there is something obstructing the path between this

unit (including devices supported by this unit) and the device equipped with Bluetooth wireless technology (such as a metal door, concrete wall, or insulation containing tinfoil), you may need to change the location of your system to prevent signal noise and interruptions.

Scope of operation

Use of this unit is limited to home use. (Transmission distances may be reduced depending on communication environment).

In the following locations, poor condition or inability to receive radio waves may cause the audio to be interrupted or stopped:

• In reinforced concrete buildings or steel framed or ironframed buildings.

• Near large metallic furniture.

• In a crowd of people or near a building or obstacle.

• In a location exposed to the magnetic field, static electricity or radio wave interference from radio communication equipment using the same frequency band (2.4 GHz) as this unit, such as a 2.4 GHz wireless LAN device (IEEE802.11b/g) or microwave oven.

• If you live in a heavily populated residential area (apartment, townhouse, etc.) and if your neighbor’s microwave is placed near your system, you may experience radio wave interference. If this occurs, move your unit to a different place. When the microwave is not in use, there will be no radio wave interference.

Radio wave reflections

The radio waves received by this unit include the radio wave coming directly from the device equipped with Bluetooth wireless technology (direct wave) and waves coming from various directions due to reflections by walls, furniture and building (reflected waves). The reflected waves (due to obstacles and reflecting objects) further produce a variety of reflected waves as well as variation in reception condition depending on locations. If the audio cannot be received properly due to this phenomenon, try moving the location of the device equipped with Bluetooth wireless technology a little. Also note that audio may be interrupted due to the reflected waves when a person crosses or approaches the space between this unit and the device equipped with Bluetooth wireless technology.

Precautions regarding connections to products supported by this unit

• Complete connections for all devices supported by this unit, including all audio cords and power cables before connecting them to this unit.

• After completing connections to this unit, check the audio and power cables to confirm that they not twisted together.

• When disconnecting this unit, confirm that you have sufficient working space in the surrounding area.

• When changing connections of audio or other cables for products supported by this unit, confirm that you have sufficient working space in the surrounding area.

Additional information 10

English Français Español

Chapter 10:

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.

General problem

Problem Check Remedy

Settings you have made have been cleared.

Was the power cord unplugged? When power cord is unplugged, the settings you have made is

cleared. Please set the clock again. If you do not want to clear the settings, do not unplug the power cord.

Difference in volume between CDs, MP3, Tuner, and AUDIO IN.

This is not a problem with this unit. The volume may sound differently depending on the input source

and recording format.

When using an analogue player with this unit, connect a device equipped with phono equalizer.

This unit cannot be operated with the remote control.

Are you operating from far away? Operate within 7 m, 30º of the remote sensor on the front panel

(page 5).

Is the remote control sensor exposed to direct sunlight or strong artificial light from a fluorescent bulb, etc.?

The remote control signals may not be received properly if the remote control sensor is exposed to direct sunlight or strong artificial light from a fluorescent bulb, etc.

Are the batteries dead? Replace the batteries (page 5).

Disc cannot be played or disc is ejected automatically.

Is the disc scratched? Scratched discs may not play.

Is the disc dirty? Wipe the dirt off the disc (page 33).

Is this unit placed in a humid location?

There could be condensation inside. Wait a while for the condensation to evaporate. Do not place this unit near an airconditioner, etc. (page 32).

Folder or file names are not recognized.

Have you exceeded the maximum number of folder or file names this unit can recognize?

The unit can recognize up to 999 files on a single disc or on a single USB memory device. The number of folders is up to 255. Depending on the folder structure, there may be folders or files that the unit cannot recognize.

The unit turns off automatically.

If no play back and no operation has done for 20 minutes or more, the unit turns off automatically. In this case it is required that the Auto power off is switched to

(page 33).

Additional information10

When a USB storage device is connected

Problem Check Remedy

USB storage device is not recognized.

Is the USB storage device properly connected?

Connect the device securely (all the way in).

Is the USB storage device connected via a USB hub?

This unit does not support USB hubs. Connect the USB storage device directly.

This unit only supports USB mass storage class devices.

This unit supports portable flash memory and digital audio playback devices.

Only the FAT16 and FAT32 file systems are supported. Other file systems (exFAT, NTFS, HFS etc.) are not supported.

This device does not support the use of external hard disc drives.

This is not a problem with this unit. Turn the power off then back on.

Some USB storage devices may not be recognized properly.

File cannot be played. Is the file copyright-protected (by

DRM)?

This is not a problem with this unit. Files stored on a computer cannot be played.

It may not be possible to play some files.

Folder or file names are not displayed or are not properly displayed.

Do the folder of file names contain more than 30 characters?

The maximum number of characters displayable for the folder and file names is 30.

Folder or file names are not displayed in alphabetical order.

This is not a problem with this unit. The order of the folder and file names displayed depends on the

order in which the folders or files were recorded on the USB storage device.

Much time is required to recognize the USB storage device.

What is the USB storage devices capacity?

Some time may be required to load the data when large capacity USB storage devices are connected (this could take several minutes).

+ 214 hidden pages