Pioneer XDJ-RX2 User Manual

XDJ-RX2
Français Deutsch ItalianoEnglish
DJ-SYSTEM SISTEMA DJ
pioneerdj.com/support/ rekordbox.com/
For FAQs and other support information for this product, visit the above site. Pour les FAQ et autres informations de support sur ce produit, consultez le site ci-dessus. Häufig gestellte Fragen und weitere Support-Informationen für dieses Produkt finden Sie auf der oben
genannten Seite. Per la sezione FAQ e altre informazioni di supporto per questo prodotto, visitare il sito indicato sopra.
Operating Instructions (Quick Start Guide) Mode d’emploi (Guide de démarrage rapide) Bedienungsanleitung (Kurzanleitung) Istruzioni per l’uso (Guida di avvio veloce)
CAUTION
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER PA SERVICE PERSONNEL.
WARNING
This equipment is not waterproof shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture
WARNING
This product equipped with a three-wire grounding (earthed) plug - a plug that has a third (grounding) pi This plug only fits a grounding-type power outlet. If you are unable to insert the plug into an outlet, contact a licensed electrician to replace the outlet with a properly grounded one. Do not defeat the safety purpose of the grounding plug.
WARNING
To sources (such as a lighted candle) on the equipment.
Operating Envir
Operating environment temperature and humidit +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light).
VENTILATION CAUTION
When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 5 cm at rear
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used
P designated collection facilities or to a retailer (if you purchase a similar new one)
Fo
By doing so you will ensure that your disposed product undergoes the necessar negative effects on the environment and human health.
electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
rivate households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to
r countries not mentioned above, please contact your local authorities for the correct method of disposal.
.
y treatment, recovery and recycling and thus prevent potential
K058b_A1_En
RTS INSIDE. REFER SERVICING TO QUALIFIED
.
-SERVICEABLE
D3-4-2-1-1_B1_En
. To prevent a fire or
D3-4-2-1-3_A1_En
For Finland customers
Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan
For Norway customers
Apparatet må tilkoples jordet stikkontakt
For Sweden customers
D3-4-2-1-6_A1_En
Apparaten skall anslutas till jordat uttag
For Denmark customers
Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord.
D3-4-2-1-6b_B1_En
prevent a fire hazard, do not place any naked flame
D3-4-2-1-7a_A1_En
onment
y:
, and 5 cm at each side).
D3-4-2-1-7c*_A2_En
D3-4-2-1-7d*_A1_En
n.
CAUTION
The switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).
D3-4-2-2-2a*_A1_En
When using this product, confirm the safety information shown on the bottom of the unit.
D3-4-2-2-4_B1_En
CAUTION
This product is evaluated in moderate and tropical climate condition.
D3-8-2-1-7a_A1_En
The graphical symbol placed on the product means alternating current. The graphical symbol placed on the product means direct current. The graphical symbol placed on the product means Class II equipment.
D3-8-2-4_A1_En
Recording equipment and copyright: Recording
equipment should be used only for lawful copying and you are advised to check carefully what is lawful copying in the country in which you are making a copy. Copying of copyright material such as films or music is unlawful unless permitted by a legal exception or consented to by the rightowners.
K018_A1_En
This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.
K041_A1_En
En
2
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest se dealer for a replacement.
S002*_A1_En
. A damaged power cord
rvice center or your
English
En
3
Contents
How to read this manual
! Thank you for purchasing this Pioneer DJ product. Read this manual and the Operating Instructions that is available on
the Pioneer DJ site before using the product. Both contain important information that you should understand to properly use the product.
Be sure to read the “Safety Precautions”. Keep this manual and the
“Warranty” included at the end of this manual in a safe place.
For obtaining the Operating Instructions for this product, see
Obtaining the Operating Instructions (p. 5 ).
! In this manual, names of channels and buttons on the product, etc.,
are enclosed in square brackets ([ ]). (e.g. [CH1], [USB STOP] button)
Before start
Features ....................................................................................................... 5
Obtaining the Operating Instructions....................................................... 5
Accessories ................................................................................................. 5
Preparing the software ............................................................................... 5
Supported media ........................................................................................ 6
Part names
Power section .............................................................................................. 7
USB section................................................................................................. 7
Deck section ................................................................................................ 7
Browse section ........................................................................................... 8
Mixer/effect section .................................................................................... 8
Connections
Connecting input/output terminals ........................................................ 10
Operation
Playback .................................................................................................... 13
Outputting sound ..................................................................................... 13
Monitoring sound with headphones ....................................................... 14
Turning off the system .............................................................................. 14
Additional information
Troubleshooting ........................................................................................ 15
Error messages ......................................................................................... 17
Changing the settings .............................................................................. 17
Cleaning the touch display ...................................................................... 17
Trademarks and registered trademarks ................................................. 17
Software license notice ............................................................................ 17
Cautions on copyrights ............................................................................ 17
Specifications............................................................................................ 18
En
4
Before start
Features
This unit is a system integrating a DJ player and DJ mixer in a single unit and inherits the technology of the Pioneer DJ CDJ series and DJM series, the world standard for club equipment. Full-fledged DJ perfor­mances can be made using tracks on USB devices and computers.
Obtaining the Operating Instructions
Some operating instructions are provided in PDF files. Adobe® Reader® is required to view the PDF files.
high-performance (for example, connecting the computer to a power outlet to maintain a stable power supply) especially when using rekordbox on a laptop.
! A separate contract with an internet service provider and payment of
the utilization fee are required to access the internet.
! Use the latest version/service pack of the operating system.
Obtaining the rekordbox software
1 Launch a web browser on the computer and access the rekordbox.com site below.
rekordbox.com
2 Click [Download] in the [Download] menu of “rekordbox.com”.
The rekordbox download page is displayed.
3 Click the download banner.
Downloading of rekordbox starts.
English
1 Launch a web browser on a computer and access the following Pioneer DJ support site.
pioneerdj.com/support/
2 Click [Manuals] under [XDJ-RX2].
3 Click on the desired language on the download page.
Download of the Operating Instructions starts.
Accessories
! Power cord ! USB cable ! Operating Instructions (Quick Start Guide) (this document) ! Warranty (for some regions) ! Software license notice ! rekordbox dj license key card
1 The included warranty is for the European region.
1
Caution
The license key cannot be reissued. Be careful not to lose it.
Preparing the software
Music management software, rekordbox, and the driver software are not included with this product. Access the rekordbox site and Pioneer DJ support site, and download the rekordbox software and driver software respectively. ! Prepare a computer, network devices, etc., that are required to
access the internet.
About rekordbox and rekordbox dj
! rekordbox is a composite software that enables track management
and DJ performances. Music files on computers and mobile devices can be managed (analysis, setting, creation, and history storage) with the music management software rekordbox. Excellent DJ per­formances can be achieved by using the music files managed by rekordbox together with this unit.
! The DJ performance function of rekordbox is called rekordbox dj.
Enter the license key included with this product to use rekordbox dj.
! For information on the latest system requirements, compatibil-
ity, and supported operating systems of rekordbox, see [System Requirements] from [Support] on the Pioneer DJ website (rekord-
box.com). rekordbox.com ! Operation on all computers is not guaranteed even if the computers
meet the required operating environment. ! The CPU and hard disc may not provide sufficient processing capa-
bilities depending on the power-saving setting, etc. on the computer.
Confirm that the computer meets conditions to provide constant
Installation (Windows)
Do not connect this unit and the computer until the installation is completed.
! Log in to the computer as the administrator before installation. ! Close all the applications running on the computer before
installation.
1 Unzip the downloaded rekordbox software file.
2 Double-click the rekordbox software to launch the installer.
3 Read the terms of the license agreement carefully, and if you agree, select [I agree to the license terms and conditions], then click [Next].
After the installation destination is specified, the installation starts. ! If you do not agree to the license agreement, click [Close] to cancel
the installation.
4 If the installation completion screen appears, click [Close] to close the rekordbox installer.
Installation (Mac OS)
Do not connect this unit and the computer until the installation is completed. ! Close all the applications running on the computer before
installation.
1 Unzip the downloaded rekordbox software file.
2 Double-click the rekordbox software to launch the installer.
3 Read the license agreement, select [Agree] if you agree to the terms.
Proceed by following the instructions on the screen. ! If you do not agree to the contents of the license agreement, click
[Disagree] to quit installation.
4 When the installation completion screen appears, click [Close] to close the rekordbox installer.
rekordbox (iOS/Android)
Tracks managed by rekordbox can be played by connecting the mobile device on which rekordbox (iOS/Android) is installed via USB. For the supported devices, see the Pioneer DJ website (rekordbox.com). ! For details on installing rekordbox (iOS/Android), see the Pioneer DJ
website (rekordbox.com).
En
5
Driver software
Audio driver software
! Dedicated driver software is required for outputting audio signals
from a computer.
 USB (LINK Export) connections driver software
for rekordbox (Mac/Windows)
! Dedicated driver software is required for connecting the unit and
rekordbox (Mac/Windows) via USB (LINK Export).
Obtaining the driver software
1 Launch a web browser on a computer and access the following Pioneer DJ support site.
pioneerdj.com/support/ ! For information on installing the driver software, see the Pioneer
DJ support site or the Operating Instructions for this product that is available on the support site.
Supported media
This unit can play music files stored on USB mass storage devices (external hard disks, portable flash memory devices, etc.).
Supported file systems
! Information such as cue points, loops points and hot cues can be
stored via USB.
! Depending on the USB device you are using, you may not achieve
the expected performance.
! There is no guarantee that all USB devices will operate on this unit.
For more information, refer to the Operating Instructions that is avail­able on the Pioneer DJ support site.
FAT16, FAT32, HFS+ (NTFS is not supported.)
En
6
Part names
3
4
5
3
4
5
2 1
3
4
7
2 3
5
6
8
b
c
a
9
d e f
l
r
m
1
For more information, refer to the Operating Instructions that is avail­able on the Pioneer DJ support site.
Deck section
English
g
1
5
1 Power section (page 7 )
2 USB section (page 7 )
3 Deck section (page 7 )
4 Browse section (page 8 )
5 Mixer/effect section (page 8 )
Power section
1 u switch
This switch is used to switch between standby and on.
USB section
1 USB 1, 2 STOP buttons
2 USB 1, 2 indicators
3 USB 1, 2 slots
4 MASTER REC (WAKE UP) button
5 TRACK MARK button
1
2
n
o
1 LOOP OUT (OUT ADJUST) button
2 LOOP IN/4BEAT (IN ADJUST) button
3 RELOOP/EXIT button
4 DIRECTION, REV button
5 SLIP button
6 TRACK SEARCH o, p buttons
7 SEARCH m, n buttons
8 Jog dial
9 SHIFT button
a Jog dial display section
b CUE button
c f (PLAY/PAUSE) button
d CUE/LOOP CALL, c (LOOP 1/2X), d (LOOP 2X) buttons
e DELETE button
f MEMORY button
g VINYL SPEED ADJUST control
h VINYL MODE button
i SYNC/INST.DOUBLES button
j MASTER button
k TEMPO RANGE button
l MASTER TEMPO button
m TEMPO slider
n HOT CUE/CALL button
p
q
En
h i
j
k
7
o BEAT LOOP button
4
2
7
1
3
5
6
8 9
a b
c d
e
g
f
a
8
g
i j
k
l
mm
e
9
p SLIP LOOP button
q BEAT JUMP button
r Performance pads
Browse section
Mixer/effect section
1 2
3 4
6 657 7
t
s
1 QUANTIZE button
2 TIME MODE (AUTO CUE) button
3 USB 1, 2 buttons
4 MIDI button
5 rekordbox button
6 BROWSE button
7 TAG LIST button
8 INFO button
9 MENU (UTILITY) button
a BACK button
b TAG TRACK/REMOVE button
c Rotary selector
d SHORTCUT button
e TRACK FILTER/EDIT button
f Main display
g LOAD 1/2 button
En
8
b
c c
r
q
p
o
1 MIC (OFF, ON, TALK OVER) selector switch
2 MIC (OFF, ON, TALK OVER) indicator
3 MIC EQ (HI, LOW) controls
4 MIC LEVEL (MIC1, MIC2) controls
5 MASTER LEVEL control
6 DECK1, 2, LINE1, 2, PHONO1, 2 selector switch
7 TRIM control
8 BOOTH MONITOR control
9 BEAT c, d buttons
a TAP (AUTO) button
b EQ/ISO (HI, MID, LOW) controls
c Channel Level Indicator
d Master level indicator
e BEAT EFFECTS selector switch
f COLOR control
g Effect channel selector switch
h CUE (CH1, CH2, MASTER) buttons
i TIME control
j CROSS FADER CURVE (THRU,
curve selector switch)
k LEVEL/DEPTH control
d
n
, ) (crossfader
b
ff
h
l ON/OFF button
m Channel fader
n Crossfader
o HEADPHONES LEVEL control
p HEADPHONES MIXING control
q PARAMETER control
r SOUND COLOR FX (DUB ECHO, SWEEP, NOISE, FILTER)
buttons
s AUX TRIM control
t AUX selector switch
English
En
9
Connections
Computer
t
Front panel
Rear panel
t
! Connect the power cord to a power outlet after all the connections are completed. ! Turn off this unit and disconnect the power cord from the power outlet before connecting components or changing the connections. ! Refer to the operating instructions for the components to be connected. ! Be sure to use the supplied power cord. ! Connect this unit and the computer directly using the included USB cable.
Connecting input/output terminals
Rear panel, front panel
Headphones
Power amplifier, powered speakers, etc.
R
Power amplifier, powered speakers, etc.
L
Power amplifier (for booth monitor)
L
R
1 62 3 4 5 7 7 9
1 PHONES terminals
2 MASTER1 terminals
! Be careful not to accidentally insert the power cord of
another unit to [MASTER 1] terminal.
! Do not connect the terminal that can supply phantom
power to the [MASTER 1] terminal.
3 MASTER2 terminals
4 BOOTH terminals
5 Kensington security slot
6
USB terminal
DJ software
DJ player
L
R
L
R
Portable audio device
R
a
Analog player
Microphone
L
b
DJ player
L
R
8 c
Microphone
To power outle
To power outle
Power cord
Power cord
9 SIGNAL GND terminal
a MIC2 terminal
b MIC1 terminal
c AC IN
10
This product satisfies electromagnetic noise regulations when it is connected to other equipment through shielded cables (with Ferrite-cores attached) and connectors. Use only the furnished accessory connecting cables.
D44-8-1-2b_A1_En
The ferrite-cores are for the purpose of preventing electromagnetic noise, do not remove them.
D44-8-1-4_A1_En
7 LINE/PHONO terminals
8 AUX terminal
En
Basic style
To power outle
USB device on which rekordbox data is recorded
Computer
Playback on this unit is performed mainly using tracks prepared with rekordbox installed on a computer. For rekordbox operations, see the rekordbox (Mac/Windows) user’s manual from the [Help] menu of rekordbox (Mac/Windows).
PRO DJ LINK (USB Export)
You can play music files prepared using rekordbox on this unit and also use the settings such as playlists, cues, loops and hot cues set by rekordbox. Store music files and settings in a memory device (flash memory, hard disk, etc.) and connect it to this unit. Using PRO DJ LINK eliminates the need to bring a computer into the DJ booth.
rekordbox
t
Power cord
1 Connect headphones to the [PHONES] terminal.
2 Connect powered speakers, power amplifier, etc. to the [MASTER1] or [MASTER2] terminal.
! To output sound from the [BOOTH] terminals, connect speakers, etc. to the [BOOTH] terminals.
3 Connect the power cord to the unit, and then connect the power plug to the power outlet.
4 Press the [u] switch on the rear panel of this unit to turn this unit on.
5 Turn on the devices connected to the output terminals (such as a power amplifier or powered speakers).
! When a microphone, DJ player or other external device is connected to the input terminals, the connected device also turns on.
English
En
11
PRO DJ LINK (LINK Export)
! When a computer on which rekordbox is installed is taken into the DJ booth and connected to this unit using a USB cable, tracks in rekordbox can
be selected and played. This makes it possible to use the information such as playlists, cues, loops and hot cues that have been set ahead of time with rekordbox for performances.
! When a mobile device on which rekordbox (iOS/Android) is installed is connected using a USB cable, tracks in rekordbox can be selected and
played. This makes it possible to use the information such as playlists, cues, loops and hot cues that have been set ahead of time with rekordbox for performances.
! Install the driver software before connecting a USB device to a computer on which rekordbox (Mac/Windows) is installed. For details, see Driver
software on page 6 .
iPod and iPhone that can be connected to this product
! This product is compatible with iPhone7, iPhone7 Plus, iPhone SE, iPhone 6s, iPhone 6s Plus, iPhone 6, iPhone 6 Plus, iPhone 5s, iPhone 5c,
iPhone 5, iPhone 4s, and iPod touch (6th and 5th generations). ! For the latest supported devices, see the following Pioneer DJ website. rekordbox.com
When using a USB cable
To power outlet
rekordbox
Computer
Power cord
Mobile device on which rekordbox is installed
1 Connect the unit and the computer by using a USB cable, or connect the unit and the mobile device by inserting the USB cable in the USB device insertion slot.
2 Connect headphones to the [PHONES] terminal.
3 Connect powered speakers, power amplifier, etc. to the [MASTER1] or [MASTER2] terminal.
! To output sound from the [BOOTH] terminals, connect speakers, etc. to the [BOOTH] terminals.
4 Turn on the power of the computer or the mobile device, and then launch rekordbox.
5 Connect the power cord to the unit, and then connect the power plug to the power outlet.
6 Press the [u] switch on the rear panel of this unit to turn this unit on.
7 Turn on the devices connected to the output terminals (such as a power amplifier or powered speakers).
! When a microphone, DJ player or other external device is connected to the input terminals, the connected device also turns on.
12
En
Operation
For more information, refer to the Operating Instructions that is avail­able on the Pioneer DJ support site.
3 Use the rotary selector to select the track you want to load.
If the rotary selector is pressed while the cursor is placed over a track title, the track menu is displayed.
4 Press the [LOAD1, 2] button.
The track is loaded into the specified deck of the unit and begins playing.
English
Playback
This section describes basic track selection operations and how to switch the screen.
Playing music files on media connected to this unit
1 Open the USB slot cover and connect a USB device.
2 Press a media button (either [USB1] or [USB2]).
Tracks and folders on the connected USB device are displayed in a list. You can switch the device from which to display the contents to the main display. [USB1] button: Displays the contents of the USB device connected to the USB1 slot. [USB2] button: Displays the contents of the USB device connected to the USB2 slot. ! The rekordbox library is displayed if it is stored in the connected USB
device.
3 Rotate the rotary selector.
Move the cursor to select an item. ! Press the rotary selector to move to a lower level in the folder. Press
the [BACK] button to return to the level above.
! When the [BACK] button is pressed for over 1 second or the medium
button for the medium being browsed is pressed, the display moves to the topmost level.
4 Use the rotary selector to select the track you want to load.
If the rotary selector is pressed while the cursor is placed over a track title, the track menu is displayed.
5 Press the [LOAD1, 2] button.
The track is loaded into the specified deck of the unit and begins playing. ! When a track has been loaded while pausing, press the
[f (PLAY/PAUSE)] button to start playback.
! When auto cue is turned on, the disc pauses at the audio start posi-
tion. In this case, press the [f (PLAY/PAUSE)] to start playback.
If the medium contains the rekordbox library
The rekordbox library is displayed if it is stored in the connected USB device. ! Music files are displayed by categories (album, artist, etc.) set with
rekordbox.
Playing the rekordbox library on a computer or mobile device
Music files are displayed by categories (album, artist, etc.) set with rekordbox.
1 Press the [rekordbox] button.
The rekordbox library is displayed on the main display of this unit.
! Press the [USB] button to select a mobile device connected by USB.
2 Rotate the rotary selector.
Move the cursor to select an item.
Outputting sound
Check that the unit and the external devices are properly connected before outputting sound. = Connecting input/output terminals (p. 10 ) Set the volume of the power amplifier or powered speakers connected to the [MASTER1] and [MASTER2] terminals to an appropriate level. Note that loud sound may be output if the volume is set too high.
Outputting the sound of channel 1 [CH1]
To output the sound of [CH 2] (channel 2), replace [CH1] with [CH 2], [DECK 1] with [DECK 2], [PHONO1] with [PHONO2], and [LINE1] with [LINE2] in the procedure below.
1 Switch the [DECK 1, LINE1, PHONO1] selector switch of [CH1].
Select the input source for [CH1] from the devices connected to this unit.
[DECK 1]: Selects rekordbox, MIDI, USB1, USB2. [LINE1]: Selects the device connected to the [LINE1] terminals. [PHONO1]: Selects the device connected to the [PHONO1]
terminals.
2 Rotate the [TRIM] control in the [CH1] section clockwise.
Adjust the level of sound input to the [CH1] terminal. The [CH1] level indicator lights when audio signals are properly input to [CH1]. Rotate the [TRIM] control to confirm that the orange indicator lights up at the highest volume for the track. Make sure that the red indicator does not light, or the sound may be distorted.
3 Move the [CH1] channel fader to the back side.
The level of the sound output from [CH1] terminals is adjusted.
4 Set the [CROSS FADER CURVE THRU, , ] (the crossfader curve selector switch).
Sets the curve characteristics of the crossfader.
5 Set the crossfader.
Switch the channel whose sound is output from the speakers.
Left edge: The [CH1] sound is output. Center position: The sound of [CH1] and [CH 2] is mixed and
output.
Right edge: The [CH 2] sound is output.
! This operation is not necessary when the [CROSS FADER CURVE
(THRU, , )] (crossfader curve selector switch) is set to [THRU].
6 Rotate the [MASTER LEVEL] control clockwise.
Sound is output from the speakers. The master level indicator lights. Rotate the [MASTER LEVEL] control to confirm that the orange indicator lights up at the highest volume for the track. ! Make sure that the master level indicator does not light, or the sound
may be distorted.
En
13
Monitoring sound with headphones
1 Connect headphones to the [PHONES] terminal.
2 Press the [CUE] button of the channel to be monitored.
3 Rotate the [HEADPHONES MIXING] control.
Adjust the balance of the volume between the channel selected with the [CUE] button and MASTER.
4 Rotate the [HEADPHONES LEVEL] control.
Adjust the volume of the headphones.
Setting monitor output
The [MONO SPLIT, STEREO] setting can be changed with UTILITY. ! [MONO SPLIT]: Outputs the sound of the channel selected with the
[CUE] button to [L] and the sound of MASTER to R. ! [STEREO]: Outputs the sound selected with the [CUE] button in
stereo. For details on the functions, see the Operating Instructions for this product.
Turning off the system
1 Press the [USB STOP] button for over 2 seconds.
Do not disconnect the USB device or turn off this unit while the USB indicator is lit or flashing. Doing so could delete the managementdata of this unit and damage the USB device, resulting in unreadable data.
2 Disconnect the USB device.
3 Close the USB slot cover.
4 Press the [u] switch.
This unit turns off.
14
En
Additional information
Troubleshooting
! Improper operation is often mistaken for trouble or a malfunction that occurred in the device. If something is wrong with this unit, check the follow-
ing issues, and also access the following Pioneer DJ support site and check [FAQ] for [XDJ-RX2]. pioneerdj.com/support/ Some problems occurs due to the connected components. If the problem cannot be resolved after checking the connected components, ask the
service center or dealer for repairs. ! The unit may not operate properly due to static electricity or other external influences. If this happens, normal operation can be sometimes restored
by removing the power cord after turning the power off, and turning the power back on after inserting the power cord into the power outlet.
Power supply
Problem Check Remedy
The unit does not turn on. The indicators do not light up.
The power suddenly turns off. Is the auto standby function activated?
Audio output
Problem Check Remedy
Sound is not output, or sound is too small.
Sound is distorted. Is the [MASTER LEVEL] control set to the proper
Sound is not output, or the output sound is distorted or noisy.
Microphone sound is not output or the volume is low.
Sound is distorted when an analog player is connected to the [PHONO] terminals of this unit. Or, lighting of the channel level indicator does not change when the [TRIM] control is turned.
Is the power cord properly connected? Connect the power cord to an AC outlet. (page 10 ) Is the [u] switch turned on? Turn on the [u] switch.
(When auto standby is functioning, the [MASTER REC (WAKE UP)] button is lit in red.)
Are the [DECK 1, LINE1, PHONO1] and [DECK 2, LINE2, PHONO2] selector switches set to the proper positions?
Are the [TRIM] control, channel faders, crossfader and [MASTER LEVEL] control set to the proper positions?
position?
Is the [TRIM] control set to the proper position? Adjust the [TRIM] control to confirm that the channel level indicator lights up in
Is the level of sound input to the [MIC] terminal set to an appropriate level?
Is this unit placed near a TV? Turn the TV off, or place this unit farther away from the TV.
Is the [MIC1, 2 LEVEL] control set to the proper position?
Is the switch on this unit or the microphone turned off?
Is an analog player with a built-in phono equalizer connected to this unit?
Is an audio interface for computers connected between the analog player and this unit?
This unit is shipped with the auto standby function set to on. If you do not want to use the auto standby function, set [AUTO STANDBY] to [OFF] on the [UTILITY] screen.
Change the input source for the channel using the [DECK 1, LINE1, PHONO1] and [DECK 2, LINE2, PHONO2] selector switches. (page 13 )
Set the [TRIM] control, channel faders, crossfader and [MASTER LEVEL] control to the proper positions. (page 13 )
Adjust the [MASTER LEVEL] control so that the master channel level indicator lights around [0 dB] at the peak level.
Set [ATT.] of [MASTER OUT] on the [UTILITY] screen to [-6 dB] or [-12 dB].
orange at the highest volume. (page 13 ) Set the [MIC1, 2 LEVEL] control to the proper position.
Set the [MIC1, 2 LEVEL] control to the proper position.
Turn the switch on.
When using an analog player with a built-in phono equalizer, connect it to the [LINE] input terminals. (page 10 )
If the analog player with a built-in phono equalizer has a LINE, PHONO selector switch, set it to PHONO.
If the audio interface for computers has a line level output, connect it to the [LINE] input terminals. (page 10 )
If the analog player has a LINE, PHONO selector switch, set it to PHONO.
English
Display
Problem Check Remedy
Playing address is not displayed in the remaining time display.
The category is not displayed. Is the rekordbox library information stored on the
The scale is not displayed. Is the track over 15 minutes long? The scale is not displayed for tracks whose playing time is over 15 minutes. The enlarged waveform is not
displayed.
Playing address may not be displayed for files recorded in VBR. This happens
USB device? Is the USB device write-protected? Disable write-protection on the USB device to make it writable.
Is the track over 60 minutes long? The enlarged waveform is not displayed for tracks whose playing time is over 60
when it takes time for the unit to detect the length of the track and display the playing address.
Use a USB device containing the library information that is exported from rekordbox to the device..
minutes.
En
15
Problem Check Remedy
The unit does not respond when the screen is touch, or the response is poor. The detected position is different from the position actually touched.
Deviation in touch display calibration. Adjust touch screen detection with the [TOUCH DISPLAY CALIBRATION] set-
tings on the [UTILITY] screen.
Functions and operations
Problem Check Remedy
The crossfade function does not work.
The back cue function does not work. Is a cue point set? Set a cue point. Beat effect does not work. Is the [LEVEL/DEPTH] control set to the center
Color effect does not work. Is the [SOUND COLOR FX
The SYNC function does not work. Has the music file been analyzed? Perform file analysis. The SYNC function does not work
even when files are analyzed.
Settings are not stored in the memory. Did you turn this unit off directly after changing
PRO DJ LINK does not work well. Is the USB (LINK Export) connections driver
Is the [CROSS FADER CURVE (THRU, (crossfader curve selector) switch set to [THRU]?
position? Is the [TRIM] control set to the proper position? Set the [TRIM] control to the proper position.
(DUB ECHO, SWEEP, NOISE, FILTER)] button pressed?
Is the [COLOR] control set to the proper position? Set the [COLOR] control to the proper position.
Is the beat grid irregular? Is the beat grid properly tapped?
Are the BPMs of the tracks in the two decks too different?
Are you scratching? The SYNC function is disabled while scratching.
the settings?
software installed?
, )]
Set the [CROSS FADER CURVE (THRU, , )] (crossfader curve selector) switch to a position other than [THRU]. (page 13 )
Rotate the [LEVEL/DEPTH] control clockwise or counterclockwise.
Press the [SOUND COLOR FX (DUB ECHO, SWEEP, NOISE, FILTER)] button.
Set the beat grid properly.
The SYNC function does work properly if the BPM of the track on the deck for which the [SYNC/INST.DOUBLES] button is pressed is not within the adjustable tempo range of the track on the deck for which the [SYNC/INST.DOUBLES] button is not pressed.
Turn this unit off 10 seconds after changing the settings. Make sure to press the [u] switch to turn this unit off.
For a USB connection, install the USB (LINK Export) connections driver software.
USB devices
Problem Check Remedy
USB device is not recognized. Is the USB device properly connected? Connect the USB device securely (all the way in).
Is the USB device connected via a USB hub? Do not use a USB hub. Is the USB device supported by this unit? This unit supports USB mass storage devices that can be used as external hard
Is the file format supported by this unit? Check that the file format of the connected USB device is supported by the unit.
Turn the unit off, wait for 1 minute, and then turn the unit on.
It takes time to read USB devices (flash memory drives and hard discs).
Playback does not start when a track is loaded from a USB device.
Files cannot be played. Is the file copyright-protected (by DRM)? Copyright-protected files cannot be played. Music files cannot be played. Are the music files damaged? Play music files that are not damaged.
Are many folders and files stored on the USB device?
Are files other than music files stored on the USB device?
Are the files playable? Check that the file format of the track is supported by the unit. Is the auto cue function enabled? Press and hold the [TIME MODE(AUTO CUE)] button for approximately 1
disks and portable flash memory devices.
(page 6 )
It takes time to read a connected USB device if the device contains many folders and files.
It takes time to read a connected USB device if files other than music files are stored in folders. Do not store files or folders other than music files on the USB device.
second or more, and disable the auto cue function.
DJ software
Problem Check Remedy
The DJ software on a computer can­not be operated.
Sound of the DJ software is not properly output.
Sound is interrupted when using the DJ software.
Is the USB cable properly connected? Connect the unit and the computer directly using the USB cable. USB hubs
Are the DJ software settings and the [MIXER MODE] setting of this unit properly set?
Is the driver software properly set? Set the driver software properly. Is the latency value of the driver software properly
set?
cannot be used. (page 10 ) Check the DJ software settings, and then check the settings of this unit on the
[UTILITY] screen and set the proper signal path.
Set the latency of the driver software to a suitable value. Set the latency of the DJ software to a suitable value.
16
En
Error messages
When this unit cannot operate normally, an error code appears on the display. Check the table below and take the measures indicated. If an error code not shown on the table below is displayed, or if the same error code is displayed again after taking the indicated action, contact your store of purchase.
Error code Error type Description of error Cause and action
E-8302
E-8304 E-8305
CANNOT PLAY TRACK
UNSUPPORTED FILE FORMAT
Track data (files) on the storage device cannot be read correctly.
Music files that cannot be played with this unit are loaded.
The track data (file) may be corrupted. dCheck if the track can be played with another player that supports the same formats as this unit.
The format is not supported by this unit.dLoad music files in the supported formats.
English
Changing the settings
For more information, refer to the Operating Instructions that is avail­able on the Pioneer DJ support site.
Cleaning the touch display
Do not use organic solvents, acids or alkalis for cleaning the surface of the touch display. Wipe with a dry soft cloth or a cloth immersed in neutral detergent and squeezed properly.
Trademarks and registered trademarks
! Pioneer DJ is a trademark of Pioneer DJ Corporation and is used
under license. rekordbox is a registered trademark or trademark of
Pioneer DJ Corporation. ! Windows is a registered trademark of Microsoft Corporation in the
United States and other countries. ! Adobe and Reader are either registered trademarks or trademarks
of Adobe Systems Incorporated in the United States and/or other
countries. ! “Made for iPod” and “Made for iPhone” mean that an electronic
accessory has been designed to connect specifically to iPod or
iPhone, respectively, and has been certified by the developer to meet
Apple performance standards. Apple is not responsible for the opera-
tion of this device or its compliance with safety and regulatory stan-
dards. Please note that the use of this accessory with iPod or iPhone
may affect wireless performance.
Software license notice
! This software is based in part on the work of the Independent JPEG
Group.
About using MP3 files
This product has been licensed for nonprofit use. This product has not been licensed for commercial purposes (for profit-making use), such as broadcasting (terrestrial, satellite, cable or other types of broadcast­ing), streaming on the Internet, Intranet (a corporate network) or other types of networks or distributing of electronic information (online digi­tal music distribution service). You need to acquire the corresponding licenses for such uses. For details, see http://www.mp3licensing.com.
Cautions on copyrights
rekordbox restricts playback and duplication of copyright-protected music contents. ! When coded data, etc., for protecting the copyright is embedded in
the music contents, it may not be possible to operate the program normally.
! When rekordbox detects that coded data, etc., for protecting the
copyright is embedded in the music contents, processing (playback,
reading, etc.) may stop. Recordings you have made are for your personal enjoyment and accord­ing to copyright laws may not be used without the consent of the copy­right holder. ! Music recorded from CDs, etc., is protected by the copyright laws of
individual countries and by international treaties. It is the full respon-
sibility of the person who has recorded the music to ensure that it is
used legally. ! When handling music downloaded from the Internet, etc., it is the
full responsibility of the person who has downloaded the music to
ensure that it is used in accordance with the contract concluded
with the download site.
! iPhone, iPod, iPod touch, and Mac are trademarks of Apple Inc.,
registered in the U.S. and other countries.
! Android™ is a trademark of Google Inc. ! iOS is a trademark on which Cisco holds the trademark right in the
US and certain other countries.
! The names of companies and products mentioned herein are trade-
marks or registered trademarks of their respective owners.
En
17
Specifications
Power requirements .................................... AC 110 V to 240 V, 50 Hz/60 Hz
Power consumption ............................................................................... 41 W
Power consumption (standby) ............................................................. 0.4 W
Main unit weight ................................................................................... 9.1 kg
Max. external dimensions ...
Tolerable operating temperature ........................................ +5 °C to +35 °C
Tolerable operating humidity ...................... 5 % to 85 % (no condensation)
Audio Section
Sampling rate ....................................................................................44.1 kHz
A/D, D/A converter .................................................................................24-bit
Frequency characteristic
USB, AUX (0 dB/12 dB), MIC1, MIC2 ........................... 20 Hz to 20 kHz
S/N ratio (rated output, A-WEIGHTED)
USB ................................................................................................ 112 dB
LINE ...............................................................................................96 dBu
PHONO............................................................................................ 85 dB
AUX (0 dB) ...................................................................................... 96 dB
AUX (12 dB).................................................................................... 90 dB
MIC .................................................................................................. 81 dB
Total harmonic distortion (20 Hz to 20 kHzBW)
USB ...............................................................................................0.003 %
LINE ..............................................................................................0.005 %
PHONO.........................................................................................0.017 %
Standard input level / Input impedance
LINE .................................................................................. –12 dBu/47 kW
PHONO.............................................................................–52 dBu/47 kW
AUX (0 dB) .......................................................................–12 dBu/47 kW
AUX (12 dB).....................................................................–24 dBu/47 kW
MIC ..................................................................................... –57 dBu/3 kW
Standard output level / Load impedance / Output impedance
MASTER 1 ..................................................+6 dBu/10 kW/390 W or less
MASTER2 ..................................................... +2 dBu/10 kW/1 kW or less
BOOTH .......................................................+6 dBu/10 kW/470 W or less
PHONES ...........................................................+8 dBu/32 W/1 W or less
Rated output level / Load impedance
MASTER 1 .......................................................................+24 dBu/10 kW
MASTER 2 .......................................................................+20 dBu/10 kW
Crosstalk
LINE ................................................................................................. 90 dB
PHONO............................................................................................ 78 dB
Channel equalizer characteristic
HI ......................................................................–∞dBto+6dB(20kHz)
MID .................................................................... –∞dBto+6dB(1kHz)
LOW .................................................................. –∞dBto+6dB(20Hz)
Microphone equalizer characteristic
HI ...................................................................–12 dB to +12 dB (10 kHz)
LOW ..............................................................–12 dB to +12 dB (100 Hz)
Input / Output terminals
PHONO input terminals
RCA pin jacks .................................................................................. 2 sets
LINE input terminal
RCA pin jacks .................................................................................. 2 sets
MIC input terminal
XLR connector & 1/4” TRS jack ........................................................2 set
AUX input terminal
RCA pin jacks ....................................................................................1 set
MASTER1 output terminal
XLR connector...................................................................................1 set
MASTER2 output terminal
RCA pin jacks ....................................................................................1 set
BOOTH output terminal
1/4” TRS jack .....................................................................................1 set
PHONES output terminal
1/4” stereo phone jack ......................................................................1 set
3.5 mm stereo mini jack ...................................................................1 set
USB terminals
A type .............................................................................................. 2 sets
Power supply............................................................... 5 V/1 A or less
B type .................................................................................................1 set
En
18
728.2 mm (W) × 108.4 mm (H) × 443.8 mm (D)
Be sure to use the [MASTER1] terminals for a balanced output.
If they are connected to an unbalanced input (such as RCA) with an XLR to RCA converter cable (or converter adapter), etc., the sound quality may be lowered or noise may occur.
Use the [MASTER2] terminals for an unbalanced input (such as
RCA).
Be sure to use the [BOOTH] terminals for a balanced output. If
they are connected to an unbalanced input, the sound quality may be lowered or noise may occur.
The specifications and design of this product are subject to
change without notice.
! © 2017 Pioneer DJ Corporation. All rights reserved.
English
En
19
ATTENTION
POUR ÉVITER TOUT RISQUE D’ÉLECTROCUTION, NE PA ARRIÈRE). A L CONFIER TOUT ENTRETIEN À UN PERSONNEL QU
AVER
Cet appareil d’incendie et de décharge électrique, ne placez près de lui un récipient rempli d’eau, tel qu’un vase ou un pot de fleurs, et ne l’exposez pas à des gouttes d’eau, des éclaboussures, de la pluie ou de l’humidité.
AVER
Cet appareil est muni d’une fiche de mise à la terre (masse) à trois fils. Comme la fiche présente une troisième broche (de terre), elle ne peut se brancher que sur une prise de courant, prévue pour une mise à la terre. Si vous n prise de courant, contactez un électricien qualifié pour faire remplacer la prise par une qui soit mise à la terre. N’annulez pas la fonction de sécurité que procure cette fiche de mise à la terre.
AVER
P flamme nue (telle qu’une bougie allumée) sur l’appareil.
Milieu de fonctionnement
Te De +5 °C à +35 °C (de +41 °F à +95 °F) ; Humidité relative inférieure à 85 % (orifices de ventilation non obstrués N’installez pas l’appareil dans un endroit mal ventilé ou un lieu soumis à une forte humidité ou en plein soleil (ou à une forte lumière artificielle).
PRÉCAUTION DE VENTILATION
Lors de l’installation de l’appareil, veillez à laisser un espace suffisant autour de ses parois de manière à améliorer la dissipation de chaleur (au moins 5 cm à l’arrière et 5 cm de chaque côté).
Si vous souhaitez vous débarrasser de cet appareil, ne le mettez pas à la poubelle avec vos ordures ménagères. Il existe un système de
Les habitants des états membres de l’UE, de Suisse et de Nor centres de collecte agréés ou à un détaillant (si vous rachetez un appareil similaire neuf).
Dans les pays qui ne sont pas mentionnés ci-dessus, veuillez contacter les autorités locales pour savoir comment vous pouvez vo de vos appareils.
V les impacts néfastes possibles sur l’environnement et la santé humaine.
collecte séparé pour les appareils électroniques usagés, qui doivent être récupérés, traités et recyclés conformément à la législation.
vège peuvent retourner gratuitement leurs appareils électroniques usagés aux
us débarrasser
ous garantirez ainsi que les appareils dont vous vous débarrassez sont correctement récupérés, traités et recyclés et préviendrez de cette façon
K058b_A1_Fr
ATTENTION
S ENLEVER LE COUVERCLE (NI LE PANNEAU
UCUNE PIÈCE RÉPARABLE PAR
’UTILISATEUR NE SE TROUVE À L’INTÉRIEUR.
ALIFIÉ UNIQUEMENT.
D3-4-2-1-1_B1_Fr
TISSEMENT
n’est pas étanche. Pour éviter les risques
D3-4-2-1-3_A1_Fr
TISSEMENT
’arrivez pas à insérer la fiche dans la
D3-4-2-1-6_A1_Fr
L’interrupteur de cet appareil ne coupe pas complètement celui-ci de sa prise secteur. Comme le cordon d’alimentation fait office de dispositif de déconnexion du secteur, il devra être débranché au niveau de la prise secteur pour que l’appareil soit complètement hors tension. Par conséquent, veillez à installer l’appareil de telle manière que son cordon d’alimentation puisse être facilement débranché de la prise secteur en cas d’accident. Pour éviter tout risque d’incendie, le cordon d’alimentation sera débranché au niveau de la prise secteur si vous prévoyez une période prolongée de non utilisation (par exemple avant un départ en vacances).
Le symbole graphique indiqué sur le produit représente le courant alternatif.
Le symbole graphique indiqué sur le produit représente le courant continu. Le symbole graphique indiqué sur le produit représente un équipement de Classe II. D3-8-2-4_A1_Fr
Appareil d’enregistrement et copyright: Vous ne pouvez utiliser un appareil d’enregistrement que pour la copie autorisée et devez vérifier attentivement ce
TISSEMENT
our éviter les risques d’incendie, ne placez aucune
D3-4-2-1-7a_A1_Fr
mpérature et humidité du milieu de fonctionnement :
)
qui est autorisé en matière de copie dans le pays où vous effectuez des copies. La copie de matériel soumis au copyright, comme les films ou la musique, est interdite sauf en cas d’autorisation exceptionnelle légale ou d’accord des détenteurs des droits.K018_A1_Fr
Ce produit est destiné à une utilisation domestique générale. Toute panne due à une utilisation autre qu'à des fins privées (comme une utilisation à des fins commerciales dans un restaurant, dans un autocar ou sur un bateau) et qui nécessite une réparation sera aux frais du client, même pendant la période de
D3-4-2-1-7c*_A1_Fr
garantie.         
NOTE IMPORTANTE SUR LE CABLE D’ALIMENTATION
Tenir le câble d’alimentation par la fiche. Ne pas débrancher la prise en tirant sur le câble et ne pas toucher le câble avec les
D3-4-2-1-7d*_A1_Fr
Lorsque vous utilisez ce produit, vérifiez les informations concernant la sécurité sous l’appareil.
D3-4-2-2-4_B1_Fr
mains mouillées. Cela risque de provoquer un court-circuit ou un choc électrique. Ne pas poser l’appareil ou un meuble sur le câble. Ne pas pincer le câble. Ne pas faire de noeud avec le câble ou l’attacher à d’autres câbles. Les câbles d’alimentation doivent être posés de façon à ne pas être écrasés. Un câble abîmé peut provoquer un risque d’incendie ou un choc électrique. Vérifier le câble d’alimentation de temps en temps.
ATTENTION
Ce produit a été testé dans des conditions de climats
Contacter le service après-vente le plus proche ou le revendeur pour un remplacement.
tempéré et tropical. D3-8-2-1-7a_A1_Fr
D3-4-2-2-2a*_A1_Fr
K041_A1_Fr
S002*_A1_Fr
Fr
2
Sommaire
Comment lire ce manuel
! Merci d’avoir acheté ce produit Pioneer DJ. Lisez ce manuel et le mode d’emploi qui est disponible sur le
site Pioneer DJ avant d’utiliser le produit. Ces deux documents contiennent des informations importantes que vous devez com­prendre pour utiliser le produit de manière appropriée.
En particulier, veillez à lire les “CONSIGNES DE SÉCURITÉ
IMPORTANTES”. En outre, veillez à conserver ce manuel avec la “Garantie”.
Pour obtenir le mode d’emploi de ce produit, reportez-vous à
Obtention du mode d’emploi (p. 4 ).
! Dans ce manuel, les noms des canaux et des touches sur le produit,
etc., sont indiqués entre crochets ([ ]). (Par exemple : [CH1], touche [USB STOP])
Informations préliminaires
Caractéristiques .......................................................................................... 4
Obtention du mode d’emploi ..................................................................... 4
Accessoires ................................................................................................. 4
Préparation du logiciel ............................................................................... 4
Supports pris en charge ............................................................................. 5
Noms des éléments
Section alimentation .................................................................................. 6
Section USB ................................................................................................ 6
Section Platines .......................................................................................... 6
Section d’exploration .................................................................................. 7
Section mixeur/effets ................................................................................. 7
Français
Raccordements
Raccordement des prises d’entrée/sortie ................................................ 9
Fonctionnement
Lecture ....................................................................................................... 12
Restitution du son .................................................................................... 12
Contrôle du son par un casque ............................................................... 13
Fermeture du système.............................................................................. 13
Informations supplémentaires
En cas de panne ....................................................................................... 14
Messages d’erreur .................................................................................... 16
Changement des réglages ....................................................................... 16
Nettoyer l’écran tactile ............................................................................. 16
Marques commerciales et marques déposées ..................................... 16
Avis relatif à la licence du logiciel ........................................................... 16
Précautions concernant les droits d’auteur .......................................... 16
Spécifications............................................................................................ 17
Fr
3
Loading...
+ 47 hidden pages