Pioneer S-W3700-K, S-FCR3700, S-FCR3300-K User Manual

WHAT’S IN THE BOX
S-FCR3700 S-FCR3300
-K
S-W3700
-K
Operating Instructions
Speaker System
http://www.pioneerelectronics.com
• S-FCR3700
• Front speakers x 2
• S-FCR3300-K
• Front speakers x 2
• S-W3700-K
• Center speaker
• Surround speakers x 2
Non-skid pads x 20 (1 set)Surround speakers x 2
• Speaker stand bases x 2
• Speaker stands x 2
• Center speaker x 1
Front right (Red)
Surround right (Grey)
• Non-skid pads
• Non-skid pads
Front right (Red)
Surround right (Grey)
Front left (White) Center (Green)
Surround left (Blue)
• Speaker cords x 5
• Screws (for bases) x 6
(small) x 12 (large) x 8
Front left (White) Center (Green)
Speaker cords x 5
• Screws (for speaker stand) x 2
Surround left (Blue)
Important
The serial number for this equipment is located on the side of the packing case. Please write this serial number on the warranty page and keep it in a secure area for future reference.
WARNING: Handling the cord on this product or cords associated with accessories sold with the
product will expose you to chemicals listed on proposition 65 known to the State of California and
other governmental entities to cause cancer and birth defect or other reproductive harm.
Wash hands after handling
• Subwoofer
Subwoofer (Purple)
• Speaker cord
• Non-skid pads (
D36-P4_A_En
large) x 4
• Operating guide
BEFORE USE
Thank you for buying this Pioneer product. Please read through these operating instructions before using
your speaker system to optimize performance.
• The nominal impedance of this speaker system is 8 Ω. Connect the speaker system to an amplifier with a load impedance ranging from 4 Ω to 16 Ω ( a model w ith “4 Ω to 16 Ω” displayed on the speaker output terminals).
In order to prevent damage to the speaker system resulting from input overload, please observe the following precautions:
• When connecting or disconnecting cables, be sure amplifier power is OFF.
• Do not use excessive amplifier volume if using a tone control to emphasize high or low frequencies.
1
En
INSTALLATION PRECAUTIONS
T
Front speaker terminals: Other speaker terminals:
Colored marker
Colored marker
Colored marker
red
black
• Do not install these units near a stove or other heating appliance, or put them in a place exposed to the sun. Such locations may cause the cabinet to change color and the speaker system to break down.
• Do not use the speaker to output distorted sound for long periods of time. This can result in a fire hazard.
• Do not connect this speaker to any amplifier other than the one supplied with this system. Connection to any other amplifier may result in a malfunction or a fire.
FRONT / CENTER / SURROUND SPEAKERS
• This speaker system is magnetically shielded. However, depending on the installation location, color distortion may occur if the speaker system is installed extremely close to the screen of a television set.
If this happens, turn off the television, then turn it on again after 15 min to 30 min. If the problem persists, place the speaker system away from the television set.
S-FCR3700:
• Do not attach the front speakers to the wall or ceiling. It may fall off and cause injury.
S-FCR3300-K:
• Do not attach the center speakers to the wall or ceiling. It may fall off and cause injury.
SUBWOOFER
• Do not attach the subwoofer to the wall or ceiling. It may fall off and cause injury.
• Do not place anything on top of the cabinet.
• Do not spill liquid on the cabinet.
• Place the subwoofer at least 8 inches (20 cm) from any wall or curtain in order to avoid heat build-up.
• The subwoofer is not magnetically shielded and so should not be placed near a TV or monitor. Magnetic storage media (such as floppy discs and tape or video cassettes) should also not be kept close to the subwoofer.
Connect to the speaker terminals on the rear of the receiver.
To connect, insert the colored wire into the matching positive (colored) terminal and the other wire into the negative (black) terminal as shown below.
Note that the color-coded tabs are as follows:
Red : Front right (R) Purple : Subwoofer
White : Front left (L) Grey : Surround right (R)
Green : Center speaker • Blue : Surround left (L)
Connect to the speaker terminals on the rear of the speakers.
Match the colored wire with the color-coded label, then insert the colored wire into the red (+) tab and the other wire with the black (
) tab.
CONNECTING YOUR SYSTEM
Important
Make sure all equipment is turned off before making any connections.
• Correct wiring of your loudspeakers is essential for achieving the best sound quality. Be careful to ensure proper polarity of connection.
CAUTION
hese speaker terminals carry HAZARDOUS LIVE
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts.
Twist and pull off the protective shields on each wire.
2
En
D3-4-2-2-3_A_En
PLACEMENT AND FINE TUNING
FRONT SPEAKERS
For best results the loudspeakers should be separated a distance approximately equal to the listening distance. Angling the loudspeakers inward towards the listener will improve the image stability for non-central listeners. Close proximity to a side or rear wall will enhance the midbass performance, although too close (particularly a corner location) and the bass may be unnaturally high and image performance may be degraded.
CENTER SPEAKER
The loudspeaker should be positioned below the TV. For best results align the front of the loudspeaker with the front of the TV. If the loudspeaker is placed under the TV and very close to the floor, then tilting upwards may be beneficial.
When installing the center speaker on top of the TV, be sure to secure it with tape or some other suitable means. Otherwise, the speaker may fall from the TV due to external shocks such as earthquakes, endangering those nearby or damaging the speaker.
SURROUND SPEAKERS
For best results the loudspeakers should be positioned at or above ear level. Depending upon your room layout and preferences, the left and right rear speakers should be positioned on the side walls just the rear of the listening position, or on the walls.
SUBWOOFER
Sound spreads in all directions in the very low frequency range. Human hearing cannot easily detect the source of very low frequencies. Be sure to provide a space of at least 8 inches (20cm) between the rear of the subwoofer and the nearest wall.
STANDARD SURROUND SETUP
This is a standard multichannel surround sound speaker setup for optimal 5.1 channel home theater sound.
Secure each of the front speakers using the plastic catch provided.
Screw two picture hooks or similar into the wall behind the speaker. Pass a cord around the hooks and through the plastic catch so that the speaker is stabilized (make sure to test that it supports the weight of the speaker).
After installing, make sure the speaker is securely fixed.
Sufficiently thick cord (not supplied)
Plastic catch
Front left
Center
Front right
Subwoofer
Listening position
Surround
left
Surround right
Assembling the speaker stand bases and securing your front speakers (S-FCR3700 only)
Attach the speaker stand bases to the stems using the screws provided.
Once you have aligned the stem and base, secure with the small screws at the points shown below. Note that the speaker should face in the direction of the base of the isosceles triangle (outlined below).
Caution
• The plastic catch is not a mounting fixture, and the speaker should not be hung directly from the wall using this catch. Always use a cord when stabilizing the speaker.
• Pioneer disclaims all responsibility for any losses or damage resulting from improper assembly, installation, insufficient strength of the installation materials, misuse, or natural disasters.
• Do not stand on the speaker stand base of the tall speaker to push or swing the speaker. The speaker may fall and break, or someone may be injured. Pay special attention to children.
NON-SKID PADS
S-FCR3700:
Attach the small non-skid pads to the base of the surround and center speakers. The large non-skid pads are for the front speakers (as shown).
Use the adhesive side of the pads to attach them to the base of each speaker.
If you choose to use speaker stands with the surround speakers, attach the non-skid pads to the stand bases instead of to the underside of the speakers.
Small non-skid pads
Front
Rear
Center speaker
Large non-skid pads
Surround speakers
Front speakers
Speaker stands
3
En
S-FCR3300-K:
Center speaker
Front or Surround
speakers
If the front, center and surround speakers are placed on a hard surface, such as wood or tile place four non-skid pads on the bottom flat surface of the speakers.
S-W3700-K:
Attach the large non-skid pads to the base of the subwoofer. Use the adhesive side of the pads to attach them to the base
of the subwoofer.
Large non-skid pads
Subwoofer
OPTIONALLY, ATTACH THE SURROUND SPEAKERS TO THE SPEAKER STANDS (S-FCR3700 ONLY)
For each speaker,line up the spurs on the stand with the holes on the back of the speaker and insert, then secure the speaker to the stand with the screw provided.
WALL-MOUNTING THE SPEAKERS
Before mounting
• Remember that the speaker system is heavy and that its weight could cause the screws to work loose, or the wall material to fail to support it, resulting in the speaker falling. Make sure that the wall you intend to mount the speakers on is strong enough to support them. Do not mount on plywood or soft surface walls.
• Mounting screws are not supplied. Use screws suitable for the wall material and support the weight of the speaker.
S-FCR3700:
Surround and Center speakers
Mounting screw
(not supplied)
3/16 in.
3/16 in. to 1/4 in. (5 mm to 7 mm)
S-FCR3300-K:
Front and Surround speakers
Mounting screw
(not supplied)
3/16 in. to 1/4 in. 5 mm to 7 mm
(5 mm)
3/8 in. (10 mm)
3/16 in. 5 mm
3/8 in. 10 mm
4
En
Note
• If you are unsure of the quality and strength of the walls, consult a professional for advice.
• Pioneer is not responsible for any accidents or damage that result from improper installation.
CABINET MAINTENANCE
Use a polishing cloth or dry cloth to wipe off dust and dirt. When the cabinet is very dirty, clean with a soft cloth dipped
in some neutral cleanser diluted five or six times with water, and then wipe again with a dry cloth. Do not use furniture wax or cleaners.
Never use thinners, benzine, insecticide sprays and other chemicals on or near the cabinets, since these will corrode the surfaces.
SPEAKER SYSTEM GRILL (S-FCR3300-K only)
The speaker system grill cannot be removed. Do not try to forcibly remove it since doing so may damage the grille.
ACCESSORIES
Speaker cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Non-skid pads (Large) (For speaker stand bases) . . . . . . . . . . . . . 8
Non-skid pads (Small)
(For center and surround speakers) . . . . . . . . . . . . . . . . . . . . . . . 12
Speaker stands (For surround speakers) . . . . . . . . . . . . . . . . . . . . 2
Screws (For speaker stands) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
S-FCR3300-K:
FRONT/SURROUND SPEAKERS
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . Bass-reflex bookshelf type
(magnetically shielded)
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..10 cm 1-way system
Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 cm cone type
Nominal impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω
Frequency range. . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Hz to 20 kHz
Dimensions
. . . . . . . . . . . . . . . . . . . . . 180 (W) mm x 130 (H) mm x 164 (D) mm
7 1/8 in. (W) x 5 1/8 in. (H) x 6 1/2 in. (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.3 kg / 2 lb 14 oz
TROUBLESHOOTING
Symptom Possible cause Remedy
No sound • Bad speaker wire or
Sound is distorted.
connection.
• Receiver is off.
• Volume control is at zero.
• Extreme signal condition. • Turn down the receiver’s
• Connect correctly or replace wire.
• Turn on receiver.
• Slowly turn up volume.
output level (volume, bass control, bass boost) to lower the level.
SPECIFICATIONS
S-FCR3700:
FRONT SPEAKERS
Enclosure . . . . . . . . . . . . . . . . . . . . . Closed-box floorstanding type
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 cm 2-way system
Speakers:
Woofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 cm cone type x 2
Tweeter . . . . . . . . . . . . . . . . . . . . . . . . . . .2.6 cm semi-dome type
Nominal impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Ω
Frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Hz to 20 kHz
Dimensions . . . . . . . . 260 mm (W) x 1096.5 mm (H) x 260 mm (D)
10 1/4 in. (W) x 43 3/16 in. (H) x 10 1/4 in. (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 kg / 9 lb 4 oz
CENTER SPEAKER
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . Closed-box bookshelf type
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 cm 1-way system
Speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 cm cone type
Nominal impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Ω
Frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Hz to 20 kHz
Dimensions . . . . . . . . . . . . 270 mm (W) x 96 mm (H) x 90 mm (D)
10 5/8 in. (W) x 3 3/4 in. (H) x 3 9/16 in. (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.78 kg / 1 lb 12 oz
SURROUND SPEAKERS
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . Closed-box bookshelf type
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 cm 1-way system
Speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 cm cone type
Nominal impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Ω
Frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Hz to 20 kHz
Dimensions . . . . . . . . . . . 100 mm (W) x 136 mm (H) x 80 mm (D)
3 15/16 in. (W) x 5 3/8 in. (H) x 3 1/8 in. (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.55 kg / 1 lb 3 oz
(magnetically shielded)
(magnetically shielded)
(magnetically shielded)
CENTER SPEAKER
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . Bass-reflex bookshelf type
(magnetically shielded)
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..10 cm 1-way system
Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 cm cone type x 2
Nominal impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω
Frequency range. . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hz to 20 kHz
Dimensions
. . . . . . . . . . . . . . . . . . . . . 350 (W) mm x 130 (H) mm x 164 (D) mm
14 in. (W) x 5 1/8 in. (H) x 6 1/2 in. (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.6 kg / 5 lb 12 oz
ACCESSORIES
Speaker cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Non-skid pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 (1set)
S-W3700-K:
SUBWOOFER
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bass-reflex floor type
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 cm 1-way system
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 cm cone type
Nominal impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω
Frequency range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Hz to 2 kHz
Dimensions. . . . . . . . . . . 190 mm (W) x 360 mm (H) x 320 mm (D)
7 1/2 in. (W) x 14 3/16 in. (H) x 12 5/8 in. (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.0 kg / 8 lb 13 oz
ACCESSORIES
Speaker cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Non-skid pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operating instructions
Note
Specifications and design subject to possible modification without notice due to improvements.
Published by Pioneer Corporation.
Copyright © 2009 Pioneer Corporation.
All rights reserved.
En
5
Loading...
+ 11 hidden pages