Pioneer SR-110 User Manual

Specifications

Frequency Range [1]

(-6dB, Half space)
(-10dB, Half space)

Nominal Coverage

Directivity Index

Q

Maximum Output [2]

Calculated Peak at rated power
Calculated Continuous

Impedance

Maximum Input Power [3]

(100 hours of 6db crest factor
IEC 268 noise spectrum)

(2 hours of 6db crest factor pink
noise, 50 - 20,000 Hz, AES method)

Recommended Amplifier Power

Sensitivity 1 watt/1 meter, half space

Crossover Frequency

Recommended Processing

Connectors

Transducers

Enclosure

Dimensions

Weight

SR-110

60-20,000 Hz
50-18,000 Hz

95° horizontal X 85° vertical
(averaged from 400 Hz to 12kHz, -6dB)

6.5 dB

4.5

123 dB
117 dB

8 ohms nominal

150 watts RMS

200 watts RMS
400 watts RMS maximum into 8 ohms

94 dB

2.3 kHz

Subsonic filter at 50 Hz as provided by QSC DCA amplifiers

Barrier strip screw terminals accept up to #10 AWG stranded
wire, four terminals two inputs, two parallel outputs

10" long throw low frequency transducer
1" mylar diaphragm compression driver on an elliptical horn

MDF, Baffle angle is 15° downward

15" wide X 20" high X 12" deep (285mm X 508mm X 364mm)

31 lbs. (15kg)

SR-110 Cinema Surround Loudspeaker

Preliminary Specifications

SR-110

[1] All frequency ranges specified refer to measured free field response (half space, 2π).
[2] Calculated SPL at 1m, (half space, 2π), speaker operating at rated RMS power with pink noise within specified frequency range.
[3] Maximum input power tested in accordance with IEC 268-5 recommendations, 50 Hz - 20 kHz band limiting, 6 dB signal crest factor.

Key Features:

Developed specifically for the unique requirements of

professional motion picture playback, QSC extends its

commitment to the cinema market with the

introduction of the SR-110 Cinema Surround

Loudspeaker. As a member of QSC’s DCS Digital

Cinema Speaker Series, the SR-110 offers high-power

handling, excellent sensitivity and extended bass

response in a very compact enclosure.

The SR-110 Cinema Surround Loudspeaker features

a high-power, long-throw 10" low frequency

transducer coupled with a 1" mylar diaphragm

compression driver. The system’s MDF enclosure

features a 15-degree down angle baffle and Array

Optimized Tuning (AOT) for optimum frequency

response. The 200 watt continuous power rating and

sophisticated protection circuit built into the

crossover provide absolute reliability.

The compact black enclosure with black grille blends

into any theatre decor. A new QuickMount bracket

design allows for fast, easy and secure installation.

The loudspeaker half of the bracket comes pre-

installed on each SR-110. The QuickMount wall

bracket is purchased separately to allow shipment to

the job site ahead of the loudspeakers. A traditional

U-bracket is also available in lieu of the QuickMount

bracket system.



Parallel outputs for feeding additional

units



95˚ horizontal dispersion



QuickMount bracket for fast, easy and

secure installation



High-power handling capability and

rugged MDF enclosure optimized for

digital soundtrack reproduction

SR-110 Enclosure Dimensions / Mounting Options

SR-110 Physical Dimensions SR-110 Mounting Options

1. QuickMount Bracket

2. U-Bracket

Top

Side

Front

11.2"

284.5 mm

20.00"

508 mm

15.68"

398.2 mm

15.68"

398.2 mm

14.63"

371.6 mm

20.0"

508 mm

15°

Specifications subject to change without notice.

1675 MacArthur Boulevard

• Costa Mesa, CA 92626 • Ph: 800/854-4079 or 714/957-7100 • Fax: [phone] •

www.qscaudio.com

SR-110 Spec Sheet 2/27/04