Pioneer PDP-SX5080D, PDP-4280XD, PDP-5080XD, PDP-SX4280D User Manual

Download

Page 1

Operating Instructions | Mode d’emploi | Bedienungsanleitung

PLASMA TELEVISION TÉLÉVISEUR PLASMA PLASMA-FERNSEHER

PDP-

PDP-SX

PDP-

PDP-SX

5080

4280

Page 2

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

WARNING : THIS APPARATUS MUST BE EARTHED. IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Green & Yellow : Earth Blue : Neutral Brown : Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows ;

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured GREEN or GREEN-AND-YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

D3-4-2-1-2-1_B_En

IMPORTANT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D3-4-2-1-1_En-A

K058_A_En

Page 3

CAUTION

The  switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

D3-4-2-2-2a_A_En

The following symbols are found on labels attached to the product. They alert the operators and service personnel of this equipment to any potentially dangerous conditions.

English

WARNING

This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage.

CAUTION

This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death.

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

D3-4-2-1-3_A_En

This product complies with the Low Voltage Directive 2006/95/EC and EMC Directive 89/336/EEC, amended by 92/31/EEC and 93/68/EEC.

WARNING

Before plugging in for the first time, read the following section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel.

D3-4-2-1-4_A_En

WARNING

This product equipped with a three-wire grounding (earthed) plug - a plug that has a third (grounding) pin. This plug only fits a grounding-type power outlet. If you are unable to insert the plug into an outlet, contact a licensed electrician to replace the outlet with a properly grounded one. Do not defeat the safety purpose of the grounding plug.

D3-4-2-1-6_A_En

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A_En

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation. For the minimum space required, see page 15.

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

STANDBY/ON Button STANDBY:

the main power flow is cut and the unit is no longer fully operational.

When placed into the standby mode,

STANDBY/ON Indicator: The indicator is lit red

when the unit is in the standby mode and is lit blue when it is in the power-on mode.

Operating Environment

Operating environment temperature and humidity: +0 ˚C to +40 ˚C (+32 ˚F to +104 ˚F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

D3-4-2-1-7c_A_En

Page 4

Contents

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However the method of connecting and operating the unit are the same.

Illustrations shown in this manual are for the PDP-5080XD/PDP-SX5080D unless otherwise specified.

Contents

01 Important user information . . . . . . . . . 6

02 Safety precautions . . . . . . . . . . . . . . . . . 9

Installation precautions. . . . . . . . . . . . . . . . . . . . . . . . .10

03 Supplied accessories . . . . . . . . . . . . . . 11

04 Part names . . . . . . . . . . . . . . . . . . . . . . 12

Plasma television. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Remote control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . .14

05 Preparation . . . . . . . . . . . . . . . . . . . . . . 15

Installing the plasma television . . . . . . . . . . . . . . . . . .15

Moving the plasma television . . . . . . . . . . . . . . . . . . . .15

Preventing the plasma television from falling over. . .16 Attaching/detaching the Pioneer stand

(for PDP-4280XD/PDP-SX4280D only). . . . . . . . . . .17

Basic connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Preparing the remote control unit . . . . . . . . . . . . . . . .20

Operating range of the remote control unit . . . . . . . .20

06 Watching TV . . . . . . . . . . . . . . . . . . . . . 21

Turning the power on . . . . . . . . . . . . . . . . . . . . . . . . . .21

Placing the system into standby . . . . . . . . . . . . . . . . .21

Changing channels . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Tuning to your favourite (analogue) channels. . . . . . .22

Changing the volume and sound . . . . . . . . . . . . . . . . .23

Switching the broadcast audio channel . . . . . . . . . . .23

Freezing images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

07 The HOME MENU . . . . . . . . . . . . . . . . . 25

HOME MENU overview . . . . . . . . . . . . . . . . . . . . . . . . .25

Using the HOME MENU . . . . . . . . . . . . . . . . . . . . . . . .25

08 Setting up. . . . . . . . . . . . . . . . . . . . . . . 26

Setting up TV channels . . . . . . . . . . . . . . . . . . . . . . . . .26

Setting up analogue TV channels manually . . . . . . . .26

Reducing video noise . . . . . . . . . . . . . . . . . . . . . . . . . .27

Setting Child Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Selecting a decoder input terminal . . . . . . . . . . . . . . .27

Labeling TV channels . . . . . . . . . . . . . . . . . . . . . . . . . .28

Sorting preset TV channels. . . . . . . . . . . . . . . . . . . . . .28

Language setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

AV Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Basic picture adjustments . . . . . . . . . . . . . . . . . . . . . .30

Advanced picture adjustments . . . . . . . . . . . . . . . . . .31

Comparing picture adjustments on the screen . . . . .34

Sound adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Power Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

09 Enjoying DTV broadcasts . . . . . . . . . . 38

Watching DTV programmes . . . . . . . . . . . . . . . . . . . . .38

Reconfiguring the DTV channel settings. . . . . . . . . . .39

Customizing channel related settings . . . . . . . . . . . . .40

Selecting a digital audio format . . . . . . . . . . . . . . . . . .42

Selecting languages for audio, subtitles,

and teletext. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Using Software Update . . . . . . . . . . . . . . . . . . . . . . . . .43

Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Common Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Page 5

Contents

English

10 Using the Electronic Programme Guide

(EPG)(for DTV only) . . . . . . . . . . . . . . . . . . 45

EPG display format. . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Using the EPG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Presetting TV programmes using the EPG . . . . . . . . 46

Using other useful EPG functions . . . . . . . . . . . . . . . 49

11 Useful adjustment settings . . . . . . . . . 50

Switching the vertical drive mode

(AV source only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Adjusting image positions

(AV source only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Adjusting image positions and clock automatically

(PC source only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Adjusting image positions and clock manually

(PC source only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Selecting an input signal type. . . . . . . . . . . . . . . . . . . 51

Colour system setting . . . . . . . . . . . . . . . . . . . . . . . . . 52

Selecting a game mode . . . . . . . . . . . . . . . . . . . . . . . . 52

Selecting a screen size manually . . . . . . . . . . . . . . . . 52

Selecting a screen size automatically . . . . . . . . . . . . 53

Detecting side masks. . . . . . . . . . . . . . . . . . . . . . . . . . 53

Changing the brightness at both sides of the screen

(Side Mask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Blue LED Dimmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Orbiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Video Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Using a password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

12 Using with other equipment . . . . . . . 57

Connecting a DVD player . . . . . . . . . . . . . . . . . . . . . . 57

Connecting a decoder . . . . . . . . . . . . . . . . . . . . . . . . . 57

Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Using the SCART output function . . . . . . . . . . . . . . . 58

Switching the SCART output. . . . . . . . . . . . . . . . . . . . 59

Connecting a game console or camcorder . . . . . . . . 59

Connecting a personal computer . . . . . . . . . . . . . . . . 60

Connecting an amplifier/AV receiver . . . . . . . . . . . . . 60

Using the HDMI Input . . . . . . . . . . . . . . . . . . . . . . . . . 61

Connecting control cords . . . . . . . . . . . . . . . . . . . . . . 63

Using i/o link.A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

13 Using the HDMI Control . . . . . . . . . . . 65

Using the HDMI Control functions . . . . . . . . . . . . . . . 65

Making the HDMI Control connections . . . . . . . . . . . 66

Setting the HDMI Control . . . . . . . . . . . . . . . . . . . . . . 68

Using the HDMI Control menus . . . . . . . . . . . . . . . . . 70

14 Using Teletext . . . . . . . . . . . . . . . . . . . 71

Using the Teletext Functions. . . . . . . . . . . . . . . . . . . . 71

Operating the Teletext basics . . . . . . . . . . . . . . . . . . . 71

15 Additional information. . . . . . . . . . . . 73

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Signal names for 15-pin mini D-sub connecter . . . . . 76

SCART pin assignments . . . . . . . . . . . . . . . . . . . . . . . 77

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Page 6

Important user information01

Chapter 1

Important user information

In order to obtain maximum enjoyment from this Pioneer PDP5080XD/PDP-SX5080D/PDP-4280XD/PDP-SX4280D plasma television, please first read this information carefully.

With the Pioneer PDP-5080XD/PDP-SX5080D/PDP-4280XD/PDPSX4280D, you can be assured of a high quality plasma television with long-life and high reliability. To achieve images of exceptional quality, this Pioneer plasma television incorporates state-of-the-art design and construction, as well as very precise and highly advanced technology.

The Pioneer PDP-5080XD/PDP-SX5080D/PDP-4280XD/PDPSX4280D plasma television incorporates the latest in colour filter technology: Direct Colour Filter. This improves the colour /picture reproduction of these models as compared to previous models. It also eliminates the need for a physical glass panel to be placed in front of the plasma display, which furthers Pioneer’s continued goal of reducing environmental waste in consumer electronics, now during the manufacturing process and in the future during the recycling process.

Over the course of its lifetime, the luminosity of the Pioneer PDP5080XD/PDP-SX5080D/PDP-4280XD/PDP-SX4280D plasma television will diminish very slowly, such as with all phosphor-based screens (for example, a traditional tube-type television). To enjoy beautiful and bright images on your Pioneer plasma television for a long time, please carefully read and follow the usage guidelines below:

Usage guidelines

All phosphor-based screens (including conventional tube-type televisions) can be affected by displaying static images for a prolonged period. Plasma televisions are no exception to this rule. After-image and permanent effects on the screen can be a voided by taking some basic precautions. By following the recommendations listed below, you can ensure longer and satisfactory results from your plasma television:

• Whenever possible, avoid frequently displaying the same image or virtually still moving pictures (e.g. closed-captioned images or video game images which have static portions).

• Do not display Teletext for a prolonged period of time.

• Avoid viewing the on-screen display for extended periods, from a decoder, DVD player, VCR and all other components.

• Do not leave the same picture freeze-framed or paused continuously over a long period of time, when using the still picture mode from a TV, VCR, DVD player or any other component.

• Images which have both very bright areas and very dark areas side by side should not be displayed for a prolonged period of time.

• When playing a video game, the “GAME” mode setting within “AV Selection” is strongly recommended. However, please do not use this mode for long periods of time.

• After playing a game or displaying any still image, it is best to view a normal moving picture in the “WIDE” or “FULL” screen setting for more than three times the length of the previous still moving image.

• After using the plasma television, always switch the display to “STANDBY” mode.

Installation guidelines

The Pioneer PDP-5080XD/PDP-SX5080D/PDP-4280XD/PDPSX4280D plasma television incorporates a very thin design. To ensure safety, please take the proper measures to mount or install the plasma television, in order to prevent the unit from tipping over in the event of vibration or accidental movement.

This product should be installed by using only parts and accessories designed by Pioneer. Use of accessories other than the Pioneer stand or installation bracket may result in instability, and could cause injury. For custom installation, please consult the dealer where the unit was purchased. To ensure correct installation, experienced and qualified experts must install the unit.

Pioneer will not be responsible for accident or damage caused by the use of parts and accessories manufactured by other companies, inadequate installation or stabilization, erroneous operation, remodeling or natural disasters.

To avoid malfunction and overheating, make sure that the vents on the main unit are not blocked when installing to ensure proper heat emission:

• Distance the unit slightly from other equipment, walls, etc. For the minimum space required around the unit, see page 15.

• Do not fit the unit inside narrow spaces where ventilation is poor.

• Do not cover with a cloth, etc.

• Clean the vents on the sides and rear of the unit to remove dust build-up, by using a vacuum cleaner set to its lowest suction setting.

• Do not place the product on a carpet or blanket.

• Do not leave the product tilted over.

• Do not turn the product upside down.

Using the unit without proper ventilation may cause the internal temperature to rise, and could result in possible malfunction. When the surrounding or internal temperature exceeds a certain degree, the display will automatically power off in order to cool the internal electronics and prevent hazardous occurrences.

Any malfunction may occur due to: an inappropriate installation site, improper assembly, installation, mounting, or operation of this product, modifications made to the product. However, Pioneer cannot be held responsible for such accidents or malfunction.

Note

The following are typical effects and characteristics of a phosphor-based matrix display and as such, are not covered by the manufacturer’s limited warranties:

• Permanent residual images upon the phosphors of the panel.

• The existence of a minute number of inactive light cells.

• Panel generated sounds, examples: Fan motor noise, and electrical circuit humming/glass panel buzzing

Caution

• Pioneer bears no responsibility for any damage arising from incorrect use of the product by you or other people, malfunctions when in use, other product related problems, and use of the product except in cases where the company must be liable.

Page 7

Important user information 01

Plasma television protection function

When still images (such as photos and computer images) stay on the screen for an extended period of time, the screen will be slightly dimmed. This is because the protection function of the plasma television automatically adjusts the brightness to protect the screen when detecting still images; so this does not designate malfunction. The screen is dimmed when a still image is detected for about three minutes.

Information of pixel defect

Plasma television displays information using pixels. Pioneer plasma television panels contain a very large number of pixels. (Depending on the panel size; over 2.3 million cells for a 42 inch display, over 3.1 million cells for a 50 inch display). All Pioneer display panels are manufactured using a very high level of ultraprecision technology and undergo individual quality control.

In rare cases, some pixels can be permanently switched off, or on, resulting in either a black or coloured pixel permanently fixed on the screen.

This effect is common to all plasma televisions because it is a consequence of the technology.

If the defective pixels are visible at a normal viewing distance of between 2.5 meters and 3.5 meters whilst viewing a normal broadcast (i.e. not a test card, still image or single colour display) please contact the supplying dealer.

If, however, they can only be seen close up or during single colour displays then this is considered normal for this technology.

Infrared rays

The plasma television releases infrared rays because of its characteristics. Depending on how the plasma television is used, the remote controls of nearby equipment may be adversely affected or wireless headphones using infrared rays are interfered by noise. If this is the case, place that equipment at a location where its remote control sensor is not affected.

Radio interference

While this product meets the required specifications, it emits a small amount of noise. If you place such equipment as an AM radio, personal computer, and VCR close to this product, that equipment may be interfered. If this happens, place that equipment far enough from this product.

Plasma television driving sound

The screen of the plasma television is composed of extremely fine pixels and these pixels emit light according to received video signals. This principle may make you hear buzz sound or electrical circuit humming from the plasma television.

Do not attach such items as labels and tape to the product

This may result in the discolouration or scratch of the cabinet.

When not using the product for a long period of time

If you do not use the product for a long period of time, the functions of the product may be adversely affected. Switch on and run the product occasionally.

Condensation

Condensation may take place on the surface or inside of the product when the product is rapidly moved from a cold place to a warm place or just after a heater is switched on in winter morning, for example. When condensation takes place, do not switch on the product and wait until condensation disappears. Using the product with condensation may result in malfunction.

Cleaning the surface of the screen and the glossy surface of the front cabinet

When cleaning the surface of the screen or the glossy surface of the front cabinet, gently wipe it with a dry soft cloth; the supplied cleaning cloth or other similar cloths (e.g., cotton and flannel). If you use a dusty or hard cloth or if you rub the screen hard, the surface of the product will be scratched.

If you clean the surface of the screen with a wet cloth, water droplets on the surface may enter into the product, resulting in malfunction.

Cleaning the cabinet

When cleaning the cabinet of this product, gently wipe it with a clean soft cloth (e.g., cotton and flannel). If you use a dusty or hard cloth or if you rub the cabinet hard, the surface of the cabinet will be scratched.

The cabinet of this product is mostly composed of plastic. Do not use chemicals such as benzene or thinner to clean the cabinet. Using these chemicals may result in quality deterioration or coating removal.

Do not expose the product to volatile gas or fluid such as pesticide. Do not make the product contact with rubber or vinyl products for a long period of time. The effect of plasticizer in the plastic may result in quality deterioration or coating removal.

If you clean the surface of the cabinet with a wet cloth, water droplets on the surface may enter into the product, resulting in malfunction.

Handles at the rear of the plasma television

Do not remove the handles from the rear of the plasma television. When moving the plasma television, ask another person for help

and use the handles attached to the rear of the plasma television. Do not move the plasma television by holding only a single handle.

Do not use the handles to hang the product when installing or carrying the product, for example. Do not use the handles for the purpose of preventing the product from tilting over.

Fan motor noise

The rotation speed of the cooling fan motor increases when the ambient temperature of the plasma television becomes high. You may hear the sound of the fan motor at that time.

To use this product for a long period of time

The Energy Save function can maintain efficiency of the screen for a long period of time. Setting the Energy Save function to “Mode 1” is recommended in order to maintain the efficiency of the screen for a long period of time.

English

Page 8

Important user information01

Caution

Panel sticking and after-image lag

Displaying the same images such as still images for a long time may cause after-image lagging. This may occur in the following two cases.

After-image lagging due to remaining electrical load

When image patterns with very high peak luminance are displayed for more than one minute, after-image lagging may occur due to the remaining electric load. The after-images remaining on the screen will disappear when moving images are displayed. The time for the after-images to disappear depends on the luminance of the still images and the time they had been displayed.

After-image (lag image) due to burning

Avoid displaying the same image on the plasma television continuously over a long period of time.

If the same image is displayed continuously for a long period, or for shorter periods of time over several days, a permanent after-image may remain on the screen due to burning of the fluorescent materials. Such images may become less noticeable if moving images are later displayed, but they will not disappear completely.

Note

• When a still image, such as a programme menu, is displayed for 5 minutes to 10 minutes, the system automatically turns the image off to prevent damage from screen burning.

• To prevent screen burning, the display position is automatically changed imperceptibly when watching plasma television (see Orbiter on page 54).

Preventing Damage from screen burning

• We recommend that you enjoy watching images displayed in full screen, except when doing so may result in copyright infringement (see page 52).

• Set the Side Mask detection function to “On”, the High Definition 16:9 aspect ratio images containing side masks will be detected and the side masks will be added automatically or the image displayed in full screen, leading to more effective countermeasures taken for the screen burning (see Detecting side masks on page 53).

Page 9

Safety precautions 02

Chapter 2

Safety precautions

English

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your product, please read the following precautions carefully before using the product.

1. Read instructions - All operating instructions must be read and understood before the product is operated.

2. Keep this manual in a safe place - These safety and operating instructions must be kept in a safe place for future reference.

3. Observe warnings - All warnings on the product and in the instructions must be observed closely.

4. Follow instructions - All operating instructions must be followed.

5. Cleaning - Unplug the power cord from the AC outlet before cleaning the product. To clean the product, use the supplied cleaning cloth or other soft clothes (e.g., cotton, flannel). Do not use liquid cleaners or aerosol cleaners.

6. Attachments - Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents.

7. Water and moisture - Do not use the product near water, such as bathtub, washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement.

8. Stand - Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting hardware recommended by the manufacturer.

9. When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops, excessive force and uneven floor surface can cause the product to fall from the cart.

10. Ventilation - The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.

11. Power source - This product must operate on a power source specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company.

12. Power cord protection - The power cords must be routed properly to prevent people from stepping on them or objects from resting on them. Check the cords at the plugs and product.

13. The plasma television used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the plasma television breaks.

14. Overloading - Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.

15. Entering of objects and liquids - Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/ or short internal parts. For the same reason, do not spill water or liquid on the product.

16. Servicing - Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualified service person to perform servicing.

17. Repair - If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service person to perform repairs.

a. When the power cord or plug is damaged. b. When a liquid was spilled on the product or when objects

have fallen into the product. c. When the product has been exposed to rain or water. d. When the product does not operate properly as described

in the operating instructions. Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not

described in the instructions can cause damage, which often requires extensive adjustment work by a qualified technician. e. When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any

noticeable abnormality in the product indicates that the

product needs servicing.

18. Replacement parts - In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.

19. Safety checks - Upon completion of service or repair work, request the service technician to perform safety checks to ensure that the product is in proper operating condition.

20. Wall or ceiling mounting - When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer.

21. Heat sources - Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating products (including amplifiers).

22. Unplug the power cord from the AC outlet before installing the speakers. (for PDP-5080XD/PDP-SX5080D only)

23. Never expose the screen of the plasma television to a strong impact, for example, by hitting it. The screen may be broken, resulting in fire or personal injury.

24. Do not expose the plasma television to direct sunlight for a long period of time. The optical characteristics of the front protection panel changes, resulting in discoloration or warp.

25. The plasma television weighs about 34.5 kg (76.1 lbs.) for the PDP-5080XD/PDP-SX5080D and about 31.3 kg (69.0 lbs.) for the PDP-4280XD/PDP-SX4280D (including the stand). Because it has small depth and is unstable, unpack, carry, and install the product with one more person at least and use the handles.

Page 10

Safety precautions02

Installation precautions

Observe the following precautions when installing with any items such as the optional stand.

When using the optional stand, brackets, or equivalent items

• Ask your dealer to perform the installation.

• Be sure to use the supplied bolts.

• For details, see the instruction manual that comes with the optional stand (or equivalent items).

When using other items

• Consult your dealer.

• The following six mounting holes can be used for the installation:

Rear view (PDP-5080XD/PDP-SX5080D)

Mounting holes Mounting holes

Median line

Caution

• Be sure to use four or more mounting holes symmetrical to the vertical and horizontal median lines.

• Use M8 screws, which go 12 mm to 18 mm in depth from the mounting surface of the plasma television. See the side view shown below.

• Be careful not to block the ventilation opening at the rear of the plasma television.

• Be sure to install the plasma television on a flat surface because it contains glass.

• The screw holes other than the illustrations on the left are to be used only for the specified products. Never use them for mounting non-specified products.

• Do not mount or remove the plasma television to or from the stand, with speakers attached (for PDP-5080XD/PDP-SX5080D only).

Note

• It is strongly recommended to use the optional Pioneer mounting products.

• Pioneer shall not be liable for any personal injury or product damage that results from the use of mounting items other than the optional Pioneer products.

Side view

Mounting surface

Mounting bracket

Plasma television

(or equivalent)

Median line

(PDP-4280XD/PDP-SX4280D)

Mounting holes Mounting holes

Median line

M8 screw

12 mm to 18 mm

Page 11

Supplied accessories 03

Chapter 3

Supplied accessories

English

Check that all of the following accessories are supplied in the box.

Remote control

AA size batteries x 2 (for remote control unit)

Ferrite core

Cable tie (for ferrite core)

Speed clamps x 3

Operating instructions x 2

Screws (M4 x 10 mm) x 2 (for plastic bands)

(PDP-4280XD/ PDP-SX4280D only)

Plastic bands x 2

(PDP-4280XD/ PDP-SX4280D only)

Power cable

Only the power cable appropriate for your country or region is supplied:

Bead bands x 3

Cleaning cloth

Warranty card

For Europe, except UK and Republic of Ireland

For UK and Republic of Ireland

Page 12

Part names04

Chapter 4

Part names

Plasma television

(Front)

Side PDP-5080XD/PDP-SX5080D PDP-4280XD/PDP-SX4280D Side

6 7

ON STANDBY

1  button (If the button is off, the power will not turn on even

when

, 0 to 9 on the remote control unit or STANDBY/ON on

the plasma television are pressed.)

2 POWER ON indicator 3 STANDBY indicator 4 TIMER indicator

• The TIMER indicator lights up when one or more DTV programmes are preset for watching or recording (see pages 46 to 48).

TIMER

Viewed from the underside of the display

TIMERON STANDBY

Viewed from the front of the display

The terminals on side panels are common to the PDP-5080XD/PDPSX5080D and PDP-4280XD/PDP-SX4280D.

5 Remote control sensor 6 STANDBY/ON button 7INPUT button 8 VOLUME +/– buttons 9 CHANNEL +/– buttons 10 PHONES output terminal 11 INPUT 5 terminal (S-VIDEO) 12 INPUT 5 terminal (VIDEO) 13 INPUT 5 terminals (AUDIO)

Page 13

Part names 04

Plasma television

(Rear)

PDP-5080XD/PDP-SX5080D PDP-4280XD/PDP-SX4280D

12 13 14

3 2 1

12 13 14

English

16 17

1 AC IN terminal 2 RS-232C terminal (used for factory setup) 3 CONTROL OUT terminal (supports SR+) 4 INPUT 1 terminal (HDMI) 5 INPUT 3 terminal (HDMI) 6 INPUT 4 terminal (HDMI) 7 PC INPUT terminal (Analogue RGB) 8 COMMON INTERFACE slot

• For a CA Module with a smart card

9 ANT (Antenna) input terminal

• Power can be supplied through this terminal

7 8

5 64

*For exact terminal positions, refer to the

terminal position sheet located near the terminal compartment.

The terminals from 1 to 9 are the same as the PDP-5080XD/PDP-SX5080D.

10 INPUT 1 terminal (SCART) 11 INPUT 2 terminal (SCART) 12 INPUT 3 terminal (SCART) 13 INPUT 2 terminals (Audio) 14 INPUT 2 terminals (COMPONENT VIDEO: Y, P 15 AUDIO OUT terminals 16 PC INPUT terminal (Audio) 17 DIGITAL OUT terminal (OPTICAL) 18 SPEAKERS terminals (right/left)

16 17

, PR)

Page 14

Part names04

Remote control unit

Point the remote control at the plasma television to operate.

5 6

10 11

12 13

15 16

17 18

22 23

1 : Turns on the power to the plasma television or places it

into the standby mode.

2 INPUT: Selects an input source of the plasma television.

(“INPUT 1”, “INPUT 2”, “INPUT 3”, “INPUT 4”, “INPUT 5”)

3PC: Selects the PC terminal as an input source. 40 to 9: TV/External input mode: Selects a channel.

Teletext mode: Selects a page. Turns the power on when the STANDBY indicator lights red.

5 p y : Displays the channel information.

Displays the banner information in DTV input mode.

6 g: Sets the sound multiplex mode. 7P+/P–: TV/External input mode: Selects a channel.

w/x: Teletext mode: Selects a page.

8 RETURN: Restores the previous menu screen. 9 ///: Selects a desired item on the setting screen.

ENTER: Executes a command.

10 EXIT: Returns to the normal screen in one step. 11 Colour (RED/GREEN/YELLOW/BLUE):

Teletext mode: Selects a page.

12 [: Jumps to Teletext subtitle page.

Turns subtitle on and off in DTV input mode depending on the broadcast.

13 k: Displays hidden characters. 14 TV/DTV: Switches between the TV and DTV input modes. 15 d: TV/External input mode: Freezes a frame from a moving

image. Press again to cancel the function.

: Teletext mode: Stops updating Teletext pages. Press

again to release the hold mode.

16 f: Selects the screen size. 17 HDMI CONTROL: Displays the HDMI Control menu. 18 e: Mutes the sound. 19 i +/i –: Sets the volume. 20 HOME MENU: Displays the HOME MENU screen. 21 EPG: Displays the Electronic Programme Guide in DTV input

mode.

22 m: Selects the Teletext mode (all TV image, all TEXT image,

TV/TEXT image).

23 l: Displays an Index page for the CEEFAX/FLOF format.

Displays a TOP Over View page for the TOP format.

Note

• When using the remote control unit, point it at the plasma television.

Page 15

Preparation 05

Chapter 5

Preparation

English

Installing the plasma television

Over 50 cm

Over 10 cm

Location

• Avoid direct sunlight. Maintain adequate ventilation.

Caution

• If you do not leave sufficient space above the plasma television, it will not receive enough ventilation and will not operate properly.

• Pioneer will not be responsible for accident or damage caused by inadequate installation or stabilization, erroneous operation, remodeling or natural disasters.

Moving the plasma television

When installing on a rack, etc., hold the plasma television as shown below. Because the plasma television is heavy, be sure to have someone help you when moving it.

(for PDP-5080XD/PDP-SX5080D)

Note

• Do not use the speaker to support the weight of the plasma television.

• Always remove the speakers before moving the plasma television. Do not hold the plasma television by the speaker mounting fittings.

(for PDP-4280XD/PDP-SX4280D)

Note

• Allow enough space around the upper and back parts when installing to ensure adequate ventilation of the rear of the unit.

• Be sure to install the plasma television in a flat, stable location.

Using the optional Pioneer stand (for PDP-5080XD/PDP-SX5080D only)

For details on installation, refer to the instruction manual supplied with the stand.

Using the optional Pioneer speakers (for PDP-5080XD/PDP-SX5080D only)

For details on installation, refer to the instruction manual supplied with the speakers.

Page 16

Preparation05

Wood screw

Screw

ScrewScrew

Preventing the plasma television from falling over

After installing the stand, be sure to take special care to ensure that the plasma television will not fall over and is stabilized to both the wall and rack.

Stabilizing on a table or rack For PDP-5080XD/PDP-SX5080D:

Stabilize the plasma television as shown in the diagram using the plastic bands and screws supplied with the optional stand.

For PDP-4280XD/PDP-SX4280D:

Stabilize the plasma television as shown in the diagram using the supplied plastic bands and screws.

Note

• To stabilize the plasma television on a table or rack, also use

commercially available wood screws that have a nominal diameter of 4 mm and that are at least 20 mm long.

4 mm

8 mm to 15 mm

20 mm min.

Screw (M4 x 10 mm)

Wood screw (commercially available, 4 mm x 20 mm min.)

Using a wall for stabilization

1 Attach falling prevention bolts (hooks) to the plasma television.

2 Use strong cords to stabilize it appropriately and firmly to a wall, pillar, or other sturdy element.

Perform this work in the same way on the left and right sides. Use hooks, cords and fittings that are available on the market.

Recommended hook: Nominal diameter 8 mm, length 12 mm to 18 mm

12 mm to 18 mm

1. Hook

2. Cord

Fitting

Caution

• A table or rack with adequate strength should always be used to support the plasma television. Failure to do so could result in personal injury and physical damage.

• When installing the plasma television, please take the necessary safety measures to prevent it from falling or overturning in case of emergencies, such as earthquakes, or of accidents.

• If you do not take these precautions, the plasma television could fall down and cause injury.

• The screws, hooks, cords and other fittings that you use to secure the plasma television to prevent it from overturning will vary according to the composition and thickness of the surface to which it will be attached.

• Select the appropriate screws, hooks, cords, and other fittings after first inspecting the surface carefully to determine its thickness and composition and after consulting a professional installer if necessary.

Drill a hole in the middle at the rear of the tabletop panel before using a wood screw. Perform this work the same way on the left and right sides.

Page 17

Preparation 05

)

Attaching/detaching the Pioneer stand

(for PDP-4280XD/PDP-SX4280D only)

Caution

• The weight of a 42 inch plasma television is about 29.6 kg (65.3 lbs.), it has little depth, and is unstable. Therefore, at least two people must assemble and install it.

Detaching the stand

When you use a stand, brackets and other fittings than the attached, use the following procedure to remove the attached stand.

1 With the plasma television lying flat, loosen and remove the installation bolts (1) and (2) using a screwdriver.

Installation bolts (1) (M8 x 23 mm: black)

Installation bolts (2) (M8 x 60 mm: black)

Plasma television

2 Remove the stand from the plasma television.

Sheet

(Step 2)

(Step 1)

Reattaching the stand.

1 With the plasma television lying flat, fit the stand’s support columns to the bottom of the plasma television as indicated by the arrows, then slowly insert them.

• Be extremely careful not to insert the support columns of the stand into any part of the plasma television other than the stand insertion slots. Doing so might damage the plasma television panel or its ports or result in warping of the stand.

Line up the column supports with the bottom of the plasma television, as indicated in the accompanying diagram.

2 Attach the stand at the points indicated by the arrows and tighten the installation bolts (2) and (1) firmly using a screwdriver.

Screw hole with “T” inscribed

Insert the stand into the plasma television so that an arrow with “FRONT/FACE AVANT” mark inscribed at the bottom of the stand indicates downward.

Installation bolts (1) (M8 x 23 mm: black)

Installation bolts (2) (M8 x 60 mm: black)

(Step 2)

(Step 1

English

• Make sure to keep the installation bolts (1) and (2) that have been removed as they are reused when attaching the stand to the plasma television.

Note

• Be sure to install the plasma television in a flat, stable location.

• Place a sheet or protective cover to protect the display from scratches or damage.

• Work only with the plasma television lying flat on a table or similar surface.

• When lying the plasma television down, be careful not to scratch or damage it.

Note

• Be sure to install the plasma television in a flat, stable location.

• Insert the screws into the holes vertically and tighten them.

• Place a sheet or protective cover to protect the display from scratches or damage.

• Work only with the plasma television lying flat on a table or similar surface.

• When lying the plasma television down, be careful not to scratch or damage it.

Page 18

Preparation05

Basic connections

Connecting the antenna

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used for a coaxial cable.

Caution

• When the “Aerial Power” setting is on, directly connect the aerial to the ANT input terminal at the rear of the plasma television. Connecting any device between the aerial and plasma television may cause damage to the device.

Rear view

Routing cables

When the speaker is installed under the plasma television panel (for PDP-5080XD/PDP-SX5080D only):

Rear view

Note

• Use the supplied bead bands as necessary.

• When tidying up your speaker cables, make sure to bundle them so that they are not subjected to any pressure.

Speaker cable

Bead band

Attaching speed clamps to the main unit

Use the speed clamps as necessary to route the connecting cables. The diagrams below show the location of the holes on the rear of the plasma television.

(PDP-5080XD/PDP-SX5080D)

(PDP-4280XD/PDP-SX4280D)

Standard DIN45325 plug (IEC169-2)

75-ohm coaxial cable (round cable) (commercially available)

• Connect a 75-ohm coaxial cable (commercially available) to the ANT terminal.

• If “Aerial Power” setting is enabled, use an indoor antenna with signal amplifier, 5 V 30 mA.

Antenna cable (commercially available)

If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325 plug (IEC169-2), plug it into the antenna terminal at the rear of the plasma television.

Note

• If the antenna is not connected correctly, the quality of

reception may be impaired. If images are not displaying correctly, check whether the antenna connection is correct or not.

Page 19

Preparation 05

Attaching and removing speed clamps

Insert [1] into an appropriate hole on the rear of the plasma television and snap [2] into the back of [1] to lock the clamp.

• Speed clamps are designed to be difficult to undo once in place. Please attach them carefully.

• Use pliers to twist the clamp 90º, pulling outward. The clamp may deteriorate over time and become damaged if removed.

• Be careful not to subject any connecting cables to strain.

Note

• Use the speed clamps as necessary.

Connecting the power cord

Rear view

Europe, except UK and Republic of Ireland

Power cord

UK and Republic of Ireland

English

Attaching the ferrite core

Attach the accessory ferrite core to the end of the power cord as shown in the accompanying illustration. Use the provided cable tie to prevent the ferrite core from slipping on the table.

If you do not do this, the plasma television will not conform to mandatory CE standards.

Ferrite core

Cable tie

To power outlet

AC power cord

As close as possible

Note

• Disconnect the power cord from the power outlet when the plasma television is not going to be used for a long period of time.

• Insert the power plug in the AC outlet, after all other components are connected.

Page 20

Preparation05

Preparing the remote control unit

Inserting batteries

1 Open the battery cover.

2 Load the supplied two AA size batteries while inserting their respective negative polarity (–) ends first.

Place batteries with their terminals corresponding to the (+) and (–) indicators in the battery compartment.

3 Close the battery cover.

Caution

Improper use of batteries can result in chemical leakage or an explosion. Be sure to follow the instructions below.

• When you replace the batteries, use manganese or alkaline ones.

• Place the batteries with their terminals corresponding to the (+) and (–) indicators.

• Do not mix batteries of different types. Different types of batteries have different characteristics.

• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries.

• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.

• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.

• If you will not use the remote control unit for an extended period of time, remove the batteries from it.

• WHEN DISPOSING OF USED BATTERIES, PLEASE COMPLY

WITH GOVERNMENTAL REGULATIONS OR ENVIRONMENTAL PUBLIC INSTITUTION’S RULES THAT APPLY IN YOUR COUNTRY/AREA.

Operating range of the remote control unit

Operate the remote control unit while pointing it toward the remote control sensor (t) located at the bottom right of the front panel of the plasma television. The distance from the remote control sensor must be within 7 m and the angle relative to the sensor must be within 30 degrees in the right, left, upward, or downward direction.

30º

7 m

Remote control sensor

30º

Note

• With the PDP-4280XD/PDP-SX4280D, the SR logo is located at the lower right on the speaker but the location of the remote control sensor is the same as with the PDP-5080XD/PDP-SX5080D.

Caution

• Do not expose the remote control unit to shock. In addition, do not expose the remote control unit to liquids, and do not place in an area with high humidity.

• Do not install or place the remote control unit under direct sunlight. The heat may cause deformation of the unit.

• The remote control unit may not work properly if the remote control sensor of the plasma television is under direct sunlight or strong lighting. In such case, change the angle of the lighting or plasma television, or operate the remote control unit closer to the remote control sensor.

• When any obstacle exists betwe en the remote control unit and the remote control sensor, the remote control unit may not function.

• As the batteries become empty, the remote control unit can function within a shorter distance from the remote control sensor. Replace the batteries with new ones early enough.

• The plasma television emits very weak infrared rays from its screen. If you place such equipment operated through infrared remote control as a VCR nearby, that equipment may not receive commands from its remote control unit properly or entirely. If this is the case, place that equipment at a location far enough from the plasma television.

• Depending on the installation environment, infrared rays from the plasma television may not allow this system to properly receive commands from the remote control unit or may shorten allowable distances between the remote control unit and the remote control sensor. The strength of infrared rays emitted from the screen differs, depending on images displayed on the screen.

Page 21

Watching TV 06

Chapter 6

Watching TV

English

Important

• Before watching broadcast channels, the built-in TV tuner must be set up. See Setting up TV channels on page 26 for how to do this.

Turning the power on

• Press a on the plasma television when the POWER ON and STANDBY indicators are off.

• The system is on.

• The POWER ON indicator lights up blue.

• Press a or 0 to 9 on the remote control unit or STANDBY/ON on the plasma television if the STANDBY indicator lights red.

• The POWER ON indicator lights up blue.

•If you press 0 on the remote control unit, images from INPUT 1 will be displayed.

• If you press 1 to 9, TV images will be displayed.

Placing the system into standby

• It is recommended not to unplug the plasma television from a power outlet when it is not in use. When in the standby mode, the plasma television automatically receives Electronic Programme Guide and DTV Auto Update signals.

• When the system is placed into standby mode, the main power flow is cu t and the s yste m is n o longer fully operational. A minute flow of power feeds the system to maintain operational readiness.

• If you are not going to use the plasma television for a long period of time, be sure to remove the power cord from the power outlet.

• If you unplug the plasma television from a power outlet, the clock inside the plasma television will reset with certain functions, such as timer recording, are disabled. After plugging in the plasma television again, clock information is automatically obtained as you tune in a DTV programme.

If you unplug the plasma television from a power outlet when a timer recording programme(s) has been registered, the plasma television may automatically tune in to the DTV programme in order to obtain clock information when you turn the power on the next time.

It may take a short while until the clock information is obtained. An alert will appear when you try to tune in an analogue

programme before obtaining the clock information.

Plasma television status indicators

The table below shows the operational status of the plasma television. You can check the current status of the system with the indicators on the plasma television.

Indicator status System status

POWER ON STANDBY

The power cord of the plasma television has been disconnected. Or, the power cord of the plasma television has been connected but the of the plasma television is off.

Power to the system is on.

button

Press a on the remote control unit or STANDBY/ON on the plasma television.

• The STANDBY indicator lights up red.

• The system enters the standby mode and the image on the screen disappears.

Note

•When a on the plasma television is off, you cannot turn the power on by pressing

STANDBY/ON

or 0 to 9 on the remote control unit or

on the plasma television.

The system is in the standby mode.

For other than the above, see Troubleshooting on page 73.

Note

• You can select “High”, “Mid” or “Low” for the brightness of the POWER ON indicator. For details, see Blue LED Dimmer on page 54.

Page 22

Watching TV06

Changing channels

Use the remote control or the control panel on the right-hand side of the plasma television to change channels.

Switching between the TV and DTV modes

•Press INPUT on the plasma television or TV/DTV on the remote control unit to select the DTV or TV input mode.

Channel display

AAA

STEREO

10:00

STANDARD

FULL

Using P+/P– on the remote control unit

•Press P+ to increase the channel number.

•Press P– to decrease the channel number.

Note

• CHANNEL +/– on the plasma television operates the same as P+/P–.

• P+/P– cannot pick up channels that are set to skip. For Channel Skip, see steps 13 and 14 under Setting up analogue TV channels manually on page 26.

• When in DTV mode, P+/P– cannot pick up digital channels that are set to skip or not registered as favourites (with the Favourite function set to “On”). See Customizing channel related settings on page 40.

Using 0 to 9 on the remote control unit

• Select channels directly by pressing buttons 0 to 9.

For example: Press 2 to select channel 2 (one-digit channel). Press 1 then 2 to select channel 12 (two-digit channel). While in DTV mode, press 1, 2 then 3 to select channel 123 (threedigit channel).

Note

• In standby, when you press 0, the power turns on and images come from the INPUT 1 source. Or, when you press any button from 1 to 9, TV images display.

Tuning to your favourite (analogue) channels

If you have registered your favourite (analogue) channels, selecting from the registered list may be the easiest way to tune to those channels.

1 While watching analogue broadcasts, press ENTER to call up the Favourite Channel List.

Favourites

*****

2 Select a favourite channel to tune in (/, / then ENTER).

•Press RETURN to exit the Favourite Channel List.

Note

• You can register up to 16 analogue channels as your favourite channels. For the registration, see steps 13 and 14 under Setting up analogue TV channels manually on page 26. Make sure to select “Yes (Listed)” in step 14.

*****

Page 23

Watching TV 06

Changing the volume and sound

Use the remote control or the control panel on the right-hand side of the plasma television to adjust the volume.

Using i + / i – on the remote control unit

• Press i + to increase the volume.

• Press i – to decrease the volume.

Volume adjustment

• VOLUME +/– on the plasma television operates the same as i + / i –.

Using e on the remote control unit

1 Press e to mute the sound.

e appears on the screen.

Muting

2 Press e again or

i +

to restore the sound.

Switching the broadcast audio channel

Depending on the broadcast, you can switch the audio channel.

The table below shows the available audio channels by broadcast audio type.

Setting

NICAM BroadcastsA2 BroadcastsDigital Broadcasts

Stereo

Bilingual

Monaural

Stereo

Bilingual

Monaural

AAA

NICAM STEREO

10:00

BBB

NICAM I

10:00

CCC

NICAM MONO

10:00

DDD

STEREO

10:00

EEE DUAL I 10:00

FFF MONO 10:00

GGG

STEREO