Pioneer PDP-435HDG, PDP-505HDG User Manual

PLASMA DISPLAY SYSTEM SISTEMA DE PANTALLA DE PLASMA SISTEMA DE MONITOR DE PLASMA

PDP-505HDG PDP-435HDG

Operating Instructions Manual de instrucciones Manual de instruções

CAUTION: THE POWER SWITCH DOES NOT COMPLETELY

SEPARATES THE UNIT FROM THE MAINS IN OFF POSITION.

THEREFORE INSTALL THE UNIT SUITABLE PLACES EASY TO

DISCONNECT THE MAINS PLUG IN CASE OF THE ACCIDENT. THE

MAINS PLUG OF UNIT SHOULD BE UNPLUGGED FROM THE WALL

SOCKET WHEN LEFT UNUSED FOR A LONG PERIOD OF TIME.

NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna. — Increase the separation between the equipment and

receiver. — Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV tech-

nician for help.

CAUTION:

This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.

FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Product Name: Plasma Display System

(Plasma Display) (Media Receiver)

Model Number: PDP-505HDG PDP-435HDG

(PDP-505PG) (PDP-435PG) (PDP-R05G) (PDP-R05G)

Product Category: Class B Personal Computers & Peripherals

Responsible Party Name: PIONEER ELECTRONICS (USA), INC., Customer Support Div.

Address: P.O. BOX 1760, LONG BEACH, CA., 90801-1760 U.S.A.

Phone: (800) 421-1625 For Business Customer URL http://www.PioneerUSA.com

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

WARNING: BEFORE PLUGGING IN THE UNIT FOR THE FIRST

TIME, READ THE FOLLOWING SECTION CAREFULLY.

THE VOLTAGE OF THE AVAILABLE POWER SUPPLY DIFFERS

ACCORDING TO COUNTRY OR REGION. BE SURE THAT THE

POWER SUPPLY VOLTAGE OF THE AREA WHERE THIS UNIT WILL

BE USED MEETS THE REQUIRED VOLTAGE (E.G. 230V OR 120V)

WRITTEN ON THE REAR PANEL.

WARNING: THIS PRODUCT EQUIPPED WITH A THREE-WIRE

GROUNDING (EARTHLING) TYPE PLUG. A PLUG HAVING A THIRD

(GROUNDING, EARTHLING) PIN, IT WILL ONLY FIT INTO A

GROUNDING (EARTHLING) TYPE POWER OUTLET. THIS IS A

SAFETY FEATURE. IF YOU ARE UNABLE TO INSERT THE PLUG

INTO THE OUTLET, CONTACT YOUR ELECTRICIAN TO REPLACE

YOUR OBSOLETE OUTLET. DO NOT DEFEAT THE SAFETY

PURPOSE OF THE GROUNDING (EARTHLING) TYPE PLUG.

The following symbols are found on labels attached to the product. They alert the operators and service personnel of this equipment to any potentially dangerous conditions.

WARNING:

CANDLE, SHOULD BE PLACED ON THE APPARATUS.

IF NAKED FLAME SOURCES ACCIDENTALLY FALL DOWN, FIRE

SPREAD OVER THE APPARATUS THEN MAY CAUSE FIRE.

NO NAKED FLAME SOURCES SUCH AS LIGHTED

VENTILATION: WHEN INSTALLING THIS UNIT, MAKE SURE

TO LEAVE SPACE AROUND THE UNIT FOR VENTILATION TO

IMPROVE HEAT RADIATION. FOR THE MINIMUM SPACE

REQUIRED, SEE PAGES 16 AND 17.

WARNING: SLOTS AND OPENINGS IN THE CABINET ARE

PROVIDED FOR VENTILATION AND TO ENSURE RELIABLE

OPERATION OF THE PRODUCT AND TO PROTECT IT FROM

OVERHEATING, TO PREVENT FIRE HAZARD, THE OPENINGS

SHOULD NEVER BE BLOCKED AND COVERED WITH ITEMS, SUCH

AS NEWSPAPERS, TABLE-CLOTHS, CURTAINS, ETC. ALSO DO NOT

PUT THE APPARATUS ON THE THICK CARPET, BED, SOFA, OR

FABRIC. HAVING A THICK PILE.

English

WARNING

This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage.

CAUTION

This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death.

Contents

Thank you for buying this Pioneer product.

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However the method of connecting and operating the unit is the same.

01 Important User Guidance Information

02 Safety Precautions

03 Operational Precautions

04 Supplied Accessories

Plasma Display ................................................................... 11

Media Receiver.................................................................... 11

05 Part Names

Plasma Display ................................................................... 12

Media Receiver.................................................................... 13

Remote control unit ............................................................ 15

06 Preparation

Allowed operation range of the remote control unit ....... 16

Installing the Plasma Display ............................................ 16

Installing the Media Receiver ............................................ 17

Installing the Media Receiver vertically ...................... 18

Setting the system .............................................................. 19

Routing cables .................................................................... 20

Using the remote control unit ........................................... 21

Cautions regarding the remote control unit .............. 21

Inserting batteries ......................................................... 21

Cautions regarding batteries ....................................... 21

Basic connections .............................................................. 22

Connecting to an antenna ........................................... 22

Connecting the power cord ......................................... 22

07 Watching TV

Turning on the power .......................................................... 23

Turning off the power .......................................................... 23

Changing channels ............................................................ 24

Changing the volume and sound ...................................... 25

Using the multiscreen functions ....................................... 27

Splitting the screen ...................................................... 27

Freezing images ............................................................ 27

08 Basic Adjustment Settings

Using the menu .................................................................. 28

AV mode menus ............................................................ 28

PC mode menus ........................................................... 29

Menu operation keys .................................................... 30

Setting up TV channels automatically .............................. 30

Using Auto Installation ................................................ 30

Using Auto Search ....................................................... 31

Setting up TV channels manually ...................................... 31

Using Manual Adjust ................................................... 31

Labeling TV channels ................................................... 33

Setting Child Lock ......................................................... 33

Sorting preset TV channels ................................................ 34

Language setting ................................................................ 34

AV Selection ........................................................................ 35

Picture adjustments ........................................................... 36

PureCinema .................................................................. 37

Color temperature ........................................................ 37

MPEG NR....................................................................... 38

DNR ............................................................................... 39

CTI .................................................................................. 39

DRE ................................................................................ 40

Color Management ....................................................... 40

Sound adjustments ............................................................ 41

FOCUS ........................................................................... 41

Front Surround .............................................................. 42

Power Control ...................................................................... 42

Energy Save .................................................................. 42

No Signal off (AV mode only) ....................................... 43

No Operation off (AV mode only)................................ 43

Power Management (PC mode only) .......................... 44

Contents

09 Using the Teletext Functions

What is Teletext? .................................................................. 45

Operating the Teletext basics ............................................. 45

Turning on and off Teletext ........................................... 45

Selecting and operating Teletext pages ...................... 45

Displaying subpages .................................................... 46

10 Enjoying through External Equipment

Watching a DVD image ...................................................... 47

Connecting a DVD player ............................................. 47

Displaying a DVD image .............................................. 47

Watching a VCR image ...................................................... 48

Connecting a VCR ........................................................ 48

Displaying a VCR image ............................................... 48

Watching broadcasts via a digital tuner ........................... 49

Connecting a digital tuner ........................................... 49

Displaying broadcasts via a digital tuner ................... 49

Enjoying a game console and watching

camcorder images .............................................................. 50

Connecting a game console or camcorder ................ 50

Displaying an image from the game console or

camcorder ..................................................................... 50

Watching an image from a personal computer ............... 51

Connecting a personal computer ............................... 51

Displaying an image from a personal computer ....... 51

Computer compatibility chart ...................................... 51

Enjoying through audio equipment in connection .......... 52

Connecting audio equipment ...................................... 52

Using HDMI Input ............................................................... 53

Connecting control cords .................................................. 55

About SR+ .................................................................... 55

11 Useful Adjustments Settings

Adjusting image positions (AV mode only) ...................... 56

Adjusting image positions and clock automatically

(PC mode only) .................................................................... 56

Adjusting image positions and clock manually

(PC mode only) .................................................................... 57

Color system setting (AV mode only) ................................ 57

Select a screen size ............................................................ 58

Manual Selection .......................................................... 58

Auto Selection ............................................................... 59

Wide screen signalling (WSS) (AV mode only) ................ 59

Picture aspect ratio (AV mode only) .................................. 60

Changing the brightness at both sides of the screen

(Side Mask) .......................................................................... 60

Sleep Timer .......................................................................... 61

Using a password (AV mode only) .................................... 61

Entering a password ..................................................... 61

Changing the password ............................................... 62

Resetting the password ............................................... 62

12 Appendix

Troubleshooting .................................................................. 63

Standard Channel Allocation Selections for the

Countries and Regions ....................................................... 65

Specifications ...................................................................... 66

English

01 Important User Guidance Information

In order to obtain maximum enjoyment from this Pioneer PureVision PDP-505HDG/PDP-435HDG Plasma Display System, please first read this information carefully.

With the Pioneer PureVision PDP-505HDG/PDP435HDG, you can be assured of a high quality Plasma Display System with long-life and high reliability. To achieve images of exceptional quality, this Pioneer Plasma Display System incorporates state-of-the-art design and construction, as well as very precise and highly advanced technology.

Over the course of its lifetime, the luminosity of the Pioneer PDP-505HDG/PDP-435HDG Plasma Display System will diminish very slowly, such as with all phosphor-based screens (for example, a traditional tube-type television). To enjoy beautiful and bright images on your Pioneer Plasma Display System for a long time, please carefully read and follow the usage guidelines below:

Usage guidelines

All phosphor-based screens (including conventional tube-type televisions) can be affected by displaying static images for a prolonged period. Plasma Display System’s are no exception to this rule. After-image and permanent effects on the screen can be avoided by taking some basic precautions. By following the recommendations listed below, you can ensure longer and satisfactory results from your plasma:

• Whenever possible, avoid frequently displaying the same image or virtually still moving pictures (e.g. closed-captioned images or video game images which have static portions).

• Do not display Teletext for a prolonged period of time.

• Avoid viewing the On Screen Display for extended periods, from a decoder, DVD player, VCR and all other components.

• Do not leave the same picture freeze-framed or paused continuously over a long period of time, when using the still picture mode from a TV, VCR, DVD player or any other component.

• Images which have both very bright areas and very dark areas side by side should not be displayed for a prolonged period of time.

• When playing a game, the “GAME” mode setting within “AV Selection” is strongly recommended. However, please limit its use to less than 2 hours at a time.

•After playing a game, or displaying a PC image or any still image, it is best to view a normal moving picture in the “WIDE” or “FULL” screen setting for more than 3 times the length of the previous still moving image.

•After using the Plasma Display System, always switch the display to “STANDBY” mode.

Installation guidelines

The Pioneer PureVision PDP-505HDG/PDP-435HDG Plasma Display System incorporates a very thin design. To ensure safety, please take the proper measures to mount or install the Plasma Display, in order to prevent the unit from tipping over in the event of vibration or accidental movement.

This product should be installed by using only parts and accessories designed by PIONEER. Use of accessories other than the PIONEER stand or installation bracket may result in instability, and could cause injury. For custom installation, please consult the dealer where the unit was purchased. To ensure correct installation, experienced and qualified experts must install the unit. PIONEER will not be held responsible for accident or damage caused by the use of parts and accessories manufactured by other companies.

To avoid malfunction and overheating, make sure that the vents on the main unit are not blocked when installing to ensure proper heat emission:

• Distance the unit slightly from other equipment, walls, etc. For the minimum space required around the unit, see pages 16 and 17.

• Do not fit the unit inside narrow spaces where ventilation is poor.

• Do not cover with a cloth, etc.

• Clean the vents on the sides and rear of the unit to remove dust build-up, by using a vacuum cleaner set to its lowest suction setting.

• Do not place the product on a carpet or blanket.

• Do not leave the product tilted over except the case of vertical installation of the Media Receiver.

• Do not reverse the product.

Using the unit without proper ventilation may cause the internal temperature to rise, and could result in possible malfunction. When the surrounding or internal temperature exceeds a certain degree, the display will automatically power off in order to cool the internal electronics and prevent hazardous occurrences.

Any malfunction may occur due to: an inappropriate installation site, improper assembly, installation, mounting, or operation of this product, modifications made to the product. However, PIONEER cannot be held responsible for such accidents or malfunction.

Typical effects and characteristics of a phosphor-based matrix display, e.g., permanent residual images upon the phosphor of the panel, and the existence of a minute number of inactive light cells in the screen, are not covered by local warranties.

01Important User Guidance Information

Panel sticking and after-image lag

• Displaying the same images such as still images for a long time may cause after-image lagging. This may occur in the following two cases.

1. After-image lagging due to remaining electrical

load

When image patterns with very high peak luminance are displayed for more than 1 minute, after-image lagging may occur due to the remaining electric load. The after-images remaining on the screen will disappear when moving images are displayed. The time for the after-images to disappear depends on the luminance of the still images and the time they had been displayed.

2. After-image (lag image) due to burning

Avoid displaying the same image on the Plasma Display continuously over a long period of time. If the same image is displayed continuously for several hours, or for shorter periods of time over several days, a permanent after-image may remain on the screen due to burning of the fluorescent materials. Such images may become less noticeable if moving images are later displayed, but they will not disappear completely.

• The energy save function can be set to help prevent damage from screen burning (see page 42).

English

02 Safety Precautions

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your product, please read the following precautions carefully before using the product.

1. Read instructions—All operating instructions must be read and understood before the product is operated.

2. Keep this manual in a safe place—These safety and operating instructions must be kept in a safe place for future reference.

3. Observe warnings—All warnings on the product and in the instructions must be observed closely.

4. Follow instructions—All operating instructions must be followed.

5. Cleaning—Unplug the power cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol cleaners.

6. Attachments—Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents.

7. Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement.

8. Stand—Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting hardware recommended by the manufacturer.

9. When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops, excessive force and uneven floor surface can cause the product to fall from the cart.

10. Ventilation—The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.

11. Power source—This product must operate on a power source specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company.

12. Power cord protection—The power cords must be routed properly to prevent people from stepping on them or objects from resting on them. Check the cords at the plugs and product.

13. The plasma Display used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the plasma Display breaks.

14. Overloading—Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.

15. Entering of objects and liquids—Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or short internal parts. For the same reason, do not spill water or liquid on the product.

16. Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualified service person to perform servicing.

17. Repair—If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service person to perform repairs.

a. When the power cord or plug is damaged. b. When a liquid was spilled on the product or when

objects have fallen into the product. c. When the product has been exposed to rain or water. d. When the product does not operate properly as

described in the operating instructions.

Do not touch the controls other than those described

in the operating instructions. Improper adjustment of

controls not described in the instructions can cause

damage, which often requires extensive adjustment

work by a qualified technician. e. When the product has been dropped or damaged. f. When the product displays an abnormal condition. Any

noticeable abnormality in the product indicates that

the product needs servicing.

18. Replacement parts—In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.

19. Safety checks—Upon completion of service or repair work, request the service technician to perform safety checks to ensure that the product is in proper operating condition.

20. Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer.

21. Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves and other heat- generating products (including amplifiers).

22. Unplug the power cord from the AC outlet before installing the speakers.

23. Never expose the screen of the Plasma Display to a strong impact, for example, by hitting it. The screen may be broken, resulting in fire or personal injury.

24. Do not expose the Plasma Display to direct sunlight for a long period of time. The optical characteristics of the front protection panel changes, resulting in discoloration or warp.

25. The Plasma Display weighs about 38 kg (83.8 lbs.) for the PDP-505PG and about 30.5 kg (67.3 lbs.) for the PDP435PG. Because it has small depth and is unstable, unpack, carry, and install the product with one more person at least and use the handles.

Installation Precautions

Observe the following precautions when installing with any items such as the optional stand.

When using the optional stand, brackets, or equivalent items

• Ask your dealer to perform the installation.

• Be sure to use the supplied bolts.

•For details, see the instruction manual that comes with the optional stand (or equivalent items).

When using other items

• Consult your dealer.

• The following six mounting holes can be used for the installation:

02Safety Precautions

English

Rear view

Mounting hole Mounting hole

Median line

Side view

Plasma Display

Median line

Mounting surface

Mounting bracket (or equivalent item)

M8 screw

12 to 18 mm

• Be sure to use four or more mounting holes symmetrical to the vertical and horizontal median lines.

• Use M8 screws, which go 12 to 18 mm in depth from the mounting surface of the Plasma Display. See the side view above.

• Be careful not to block the ventilation opening at the rear of the Plasma Display.

• Be sure to install the Plasma Display on a flat surface because it contains glass.

• The screw holes other than the above are to be used only for the specified products. Never use them for mounting non-specified products.

• Do not mount or remove the Plasma Display to or from the stand, with speakers attached.

• It is strongly recommended to use the optional PIONEER mounting products.

• PIONEER shall not be liable for any personal injury or product damage that results from the use of mounting items other than the optional PIONEER products.

03 Operational Precautions

PIONEER bears no responsibility for any damages arising from incorrect use of the product by you or other people, malfunctions when in use, other product related problems, and use of the product except in cases where the company must be liable.

Plasma Display protection function

When still images (such as photos and computer images) stay on the screen for an extended period of time, the screen will be slightly dimmed. This is because the protection function of the Plasma Display automatically adjusts the brightness to protect the screen when detecting still images; so this does not designate malfunction. The screen is dimmed when a still image is detected for about three minutes.

Infrared rays

The Plasma Display releases infrared rays because of its characteristics. Depending on how the Plasma Display is in use, the remote controls of nearby equipment may be adversely affected or wireless headphones using infrared rays are interfered by noise. If this is the case, place that equipment at a location where its remote control sensor is not affected.

Radio interference

While this product meets the required specifications, it emits a small amount of noise. If you place such equipment as an AM radio, personal computer, and VCR close to this product, that equipment may be interfered. If this happens, place that equipment far enough from this product.

Fan motor noise

When ambient temperature of the Media Receiver becomes high, the rotation speed of the cooling fan motor increases. This may make you feel that the fan motor is noisy at such an occasion.

Cleaning the screen

• When cleaning the screen of this product, gently wipe it with a dry soft cloth; the supplied cleaning cloth or other similar cloths (e.g., cotton and flannel). If you use a hard cloth or rub the screen hard, the surface of the screen will be scratched.

• If you clean the surface of the screen with a wet cloth, water droplets on the surface may enter into the product, resulting in malfunction.

Cleaning the cabinet

• The cabinet of this product is mostly composed of plastic. Do not use chemicals such as benzine or thinner to clean the cabinet. Using these chemicals may result in quality deterioration or coating removal.

• Do not expose the product to volatile gas or fluid such as pesticide. Do not make the product contact with rubber or vinyl products for a long period of time. The effect of plasticizer in the plastic may result in quality deterioration or coating removal.

• If you clean the surface of the cabinet with a wet cloth, water droplets on the surface may enter into the product, resulting in malfunction.

Handles at the rear of the Plasma Display

• Do not remove the handles from the rear of the Plasma Display.

• When moving the Plasma Display, ask another person for help and use the handles attached to the rear of the Plasma Display. Do not move the Plasma Display by holding only a single handle. Use the handles as shown.

• Do not use the handles to hang the product when installing or carrying the product, for example. Do not use the handles for the purpose of preventing the product from tilting over.

Do not attach such items as labels and tape to the product.

• This may result in the discoloration or scratch of the cabinet.

When not using the product for a long period of time

• If you do not use the product for a long period of time, the functions of the product may be adversely affected. Switch on and run the product occasionally.

Condensation

• Condensation may take place on the surface or inside of the product when the product is rapidly moved from a cold place to a warm place or just after a heater is switched on in winter morning, for example. When condensation takes place, do not switch on the product and wait until condensation disappears. Using the product with condensation may result in malfunction.

Plasma Display

04Supplied Accessories

English

Power cord

Warranty card

Media Receiver

Power cord

Speed clamp x 3

Speaker cushion x 3

(Use when installing the optional speakers at

the bottom of the Plasma Display.)

AA size battery x 2 (Manganese battery)

Bead band x 3

Cleaning cloth

Noise filter

Cable tie

Screw x 4

(for stand)

Remote control unit

Screw hole cap x 4

Operating instructions

• Always use the power cord supplied with the Plasma

Display and the one supplied with the Media Receiver for each respective unit.

Stand System cable (3 m)

05 Part Names

Plasma Display

Front view

(right view)

1 POWER button 2 STANDBY indicator 3 POWER ON indicator 4 Remote control sensor

Rear view

5 STANDBY/ON button 6 INPUT button 7 VOLUME +/– buttons 8 CHANNEL +/– buttons

9 SYSTEM CABLE terminal (BLACK) 0 SYSTEM CABLE terminal (WHITE)

The terminals have faced downward.

- SPEAKER (right/left) terminals = AC INLET terminal

Media Receiver

Front view

POWER

ON STANDBY

05Part Names

English

Pull this section to open the door.

1 POWER button 2 POWER ON indicator 3 STANDBY indicator 4 INPUT 4 terminal (S-VIDEO)

5 INPUT 4 terminal (VIDEO) 6 INPUT 4 terminals (AUDIO) 7 PC INPUT terminal (AUDIO) 8 PC INPUT terminal (ANALOG RGB)

05 Part Names

Rear view

IN OUT

S-VIDEO

CONTROL

VIDEO

SERVICE ONLY

INPUT 2

MONITOR

OUTPUT

ANT

67890 -23145

R-AUDIO-L

S-VIDEO

VIDEO

R-AUDIO-L

COMPONENT VIDEO

YYP

AC INLET

INPUT 1

INPUT 3

HDMI

INPUT 3

BLACK

WHITE

SYSTEM CABLE

^*(=~ ! @ # $ %

1 Antenna input terminal 2 RS-232C terminal (used for factory setup) 3 Control input terminal 4 Control output terminal 5 INPUT 2 terminal (VIDEO) 6 INPUT 2 terminals (AUDIO) 7 INPUT 1 terminal (S-VIDEO) 8 INPUT 1 terminal (VIDEO) 9 INPUT 1 terminals (AUDIO) 0 INPUT 1 COMPONENT VIDEO terminals

(Y, PB, PR)

- AC INLET terminal

= INPUT 2 terminal (S-VIDEO) ~ MONITOR OUTPUT terminal (S-VIDEO) ! MONITOR OUTPUT terminal (VIDEO) @ MONITOR OUTPUT terminals (AUDIO) # INPUT 3 terminal (S-VIDEO) $ INPUT 3 terminal (VIDEO) % INPUT 3 terminals (AUDIO) ^ INPUT 3 COMPONENT VIDEO terminals

(Y, PB, PR)

& INPUT 3 terminal (HDMI) * SYSTEM CABLE terminal (WHITE) ( SYSTEM CABLE terminal (BLACK)

Remote control unit

1 2 3 4

7 8

9 0

~ !

# $

% ^

& *

Sets the sound multiplex mode.

(RETURN)

Restores the previous menu screen.

/ / /

Selects a desired item on the setting screen.

- Color (RED/GREEN/YELLOW/BLUE)

TELETEXT mode: Selects a page.

= k

TELETEXT mode: Displays hidden characters.

~ f

TV/External input mode: Changes the wide screen size.

TELETEXT mode: (full/upper half/lower half)

! d

Freezes a frame from a moving image. Press again to cancel the function.

Switches Teletext images.

05Part Names

English

1 a

Turns on the power to the Plasma Display or places it into standby mode.

2 INPUT 1, 2, 3, 4

Selects an input source.

3 PC

Selects the PC terminal as an input source.

4 c

Switches the screen mode among 2-screen, picture-in-picture, and single-screen.

5 0 – 9

Switches on the power to the Plasma Display. TV/External input mode: Selects a channel. TELETEXT mode: Selects a page.

6 p

Displays the channel information.

7 P +/P –

TV/External input mode: Selects a channel.

w/x

TELETEXT mode: Selects a page.

TELETEXT mode: Stops updating Teletext pages.

Press again to release the hold mode.

@ CH ENTER

Executes a channel number.

# i +/i –

Sets the volume.

$ e

Mutes the sound.

% HOME MENU

TV/External Input mode: Displays the Menu screen.

^ ENTER

Executes a command.

& m

Selects the TELETEXT mode. (all TV image, all TEXT image, TV/TEXT image)

* l

TELETEXT mode:

CEEFAX/FLOF format. Displays a TOP Over View page for the TOP format.

• When using the remote control unit, point it at the Plasma Display.

Displays an Index page for the

06 Preparation

Allowed operation range of the remote control unit

Operate the remote control unit while pointing it toward the remote control sensor (t) located at the bottom right of the front panel of the Plasma Display. The distance from the remote control sensor must be within 7 m and the angle relative to the sensor must be within 30 degrees in the right or left direction.

7 m

30º

Remote control sensor

Installing the Plasma Display

Over 50 cm

Over 10 cm

Locating

• Avoid direct sunlight. Maintain adequate ventilation.

• The length of the system cable used to connect the Plasma Display and the Media Receiver is about 3 m.

• Because the Plasma Display is heavy, be sure to have someone help you when moving it.

When the remote control unit does not function properly

• When any obstacle exists between the remote control unit and the remote control sensor, the remote control unit may not function.

• As the batteries become empty, the remote control unit can function within a shorter distance from the remote control sensor. Replace the batteries with new ones early enough.

• The Plasma Display emits very weak infrared rays from its screen. If you place such equipment operated through infrared remote control as a VCR nearby, that equipment may not receive commands from its remote control unit properly or entirely. If this is the case, place that equipment at a location far enough from the Plasma Display.

• Depending on the installation environment, infrared rays from the Plasma Display may not allow this system to properly receive commands from the remote control unit or may shorten allowable distances between the remote control unit and the remote control sensor. The strength of infrared rays emitted from the screen differs, depending on images displayed on the screen.

• If you place anything on the top of the Media Receiver it will not receive enough ventilation and will not operate properly.

• Allow enough space around the upper and back parts when installing to ensure ventilation around the backside.

Using the optional PIONEER stand

•For details on installation, refer to the instruction manual provided with the stand.

Using the optional PIONEER speakers

•For details on installation, refer to the instruction manual provided with the speaker.

Operating Environment

Operating environment temperature and humidity: +0°C to +40°C; less than 85% RH (cooling vents not blocked)

Avoid installing in the following locations:

• Under direct exposure to sunlight

• Under strong artificial light

• In high humidity

•Poorly ventilated

Installing the Media Receiver

Plasma Display

Media Receiver

(vertical installation)

(horizontal installation)

POWER

System cable (approx. 3 meters)

06Preparation

POWER

ON STANDBY

English

• Do not place a VCR or any other device on top of the Media Receiver.

• When installing, allow enough space on the sides and above the Media Receiver.

• Do not block the cooling vent on any side of the Media Receiver or the rear ventilation fan opening of the Media Receiver.

Over 5 cm

POWER

ON STANDBY

Over 5 cm

Over 10 cm

Over 5 cm

POWER

ON STANDBY

Over 5 cmOver 5 cm

Over 10 cm

06 Preparation

Installing the Media Receiver vertically

You can use the accompanying stand to install the Media Receiver vertically.

Installing the Media Receiver vertically

Insert the vertical installation stand into the side of the Media Receiver.

Right side

You can remove the shock absorbing pads.

Shock absorbing pad

Keep the shock absorbing pads and screws. They are required when you place the Media Receiver in the horizontal position.

Plug the screw holes using the caps provided.

Secure the vertical installation stand with screws.

Vertical installation stand screws

Remove the separation sheet.

Align with the hole and attach.

Screw hole cap

• When you have installed the Media Receiver vertically, always use the accompanying stand. If you place the unit directly on the floor the cooling vents will be blocked which will result in mechanical failure.

Setting the system

Connecting the system cable to the Plasma Display

Plasma Display (rear view)

For details on optional PIONEER

(WHITE)

(BLACK)

speaker installation, refer to the speaker instruction manual provided.

06Preparation

English

System cable

Connecting the system cable to the Media Receiver

Media Receiver (rear view)

IN OUT

S-VIDEO

CONTROL

VIDEO

R-AUDIO-L

S-VIDEO

VIDEO

R-AUDIO-L

COMPONENT VIDEO

YYPBPBPR

INPUT 1

INPUT 3

HDMI

INPUT 3

AC INLET

BLACK

WHITE

SYSTEM CABLE

(BLACK)

(WHITE)

SERVICE ONLY

ANT

INPUT 2

MONITOR

OUTPUT

• THESE SPEAKER TERMINALS CAN BE APPLIED WITH HAZARDOUS VOLTAGE WHEN YOU CONNECT OR DISCONNECT THE SPEAKER CABLES, TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT TOUCH UNINSULATED PARTS BEFORE DISCONNECTING THE POWER CORD.

06 Preparation

Routing cables

Speed clamps and bead bands are included with this system for bunching cables. Once properly bunched, follow the steps below to route the cables.

When the speakers are installed on the sides

Speaker cable Speed clamps

Cable binders (supplied with the stand)*

Attaching speed clamps to the main unit

Attach the speed clamps using the 4 holes marked with

below, depending on your routing system.

(rear view)

Speaker cable

Attaching and removing speed clamps

Insert 1 into an appropriate hole on the rear of the Plasma Display and snap 2 into the back of 1 to lock the clamp.

Speed clamps are designed to be difficult to undo once in place. Please attach them carefully.

Use pliers to twist the clamp 90°, pulling outward. The clamp may deteriorate over time and become damaged if removed.

When the speakers are installed at the bottom

Speaker cable Speaker cable

Cable binders (supplied with the stand)*

* Cable binder

Using the cable binders supplied with the stand, put the speaker and system cables together so that the cables are invisible from the front. At that time be careful not to apply any force to the connection sections of the cables.

Using the remote control unit

Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control unit and the sensor may prevent proper operation.

Cautions regarding the remote control unit

• Do not expose the remote control unit to shock. In addition, do not expose the remote control unit to liquids, and do not place in an area with high humidity.

• Do not install or place the remote control unit under direct sunlight. The heat may cause deformation of the unit.

• The remote control unit may not work properly if the remote control sensor of the Plasma Display is under direct sunlight or strong lighting. In such case, change the angle of the lighting or Plasma Display set, or operate the remote control unit closer to the remote control sensor.

Insert the two AA size batteries supplied with the product.

• Place batteries with their terminals corresponding to the (+) and (–) indicators in the battery compartment.

Close the battery cover.

06Preparation

English

Inserting batteries

If the remote control unit fails to operate Plasma Display System functions, replace the batteries in the remote control unit.

Open the battery cover.

Cautions regarding batteries

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

• Do not use alkaline batteries. When you replace the batteries, use manganese ones.

• Place the batteries with their terminals corresponding to the (+) and (–) indicators.

• Do not mix batteries of different types. Different types of batteries have different characteristics.

• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries.

• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.

• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.

• If you will not use the remote control unit for an extended period of time, remove the batteries from it.

• WHEN DISPOSING OF USED BATTERIES, PLEASE COMPLY WITH GOVERNMENTAL REGULATIONS OR ENVIRONMENTAL PUBLIC INSTRUCTION’S RULES THAT APPLY IN YOUR COUNTRY/AREA.

06 Preparation

Basic connections

Connecting to an antenna

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used for a coaxial cable.

Antenna cable-commercially available

Standard DIN45325 plug (IEC169-2)

75-ohm coaxial cable (round cable) (commercially available)

If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325 plug (IEC169-2), plug it into the antenna terminal at the rear of the Media Receiver.

SERVICE ONLY

OUTIN

CONTROL

ANT

S-VIDEO

INPUT 2

MONITOR OUTPUT

S-VIDEO

R-AUDIO-L

VIDEO

COMPONENT VIDEO

VIDEO

R-AUDIO-L

INPUT 1

INPUT 3

HDMI

YYP

INPUT 3

AC INLET

BLACK

WHITE

SYSTEM CABLE

Connecting the power cord

Plasma Display (bottom view)

Media Receiver (rear view)

OUTIN

CONTROL

SERVICE ONLY

ANT

S-VIDEO

INPUT 2

MONITOR OUTPUT

S-VIDEO

R-AUDIO-L

VIDEO

COMPONENT VIDEO

VIDEO

R-AUDIO-L

INPUT 1

INPUT 3

HDMI

YYP

INPUT 3

AC INLET

BLACK

WHITE

SYSTEM CABLE

To a wall outlet

• Always turn off the main power of the Plasma Display and Media Receiver when connecting the power cords.

• Disconnect the power cord from the power outlet, Plasma Display and Media Receiver when the system is not

going to be used for a long period of time.

07Watching TV

Unless you set up TV channels that you can watch under the current conditions, you cannot tune in those channels. For the procedure, see “Setting up TV channels automatically” on pages 30 to 31.

Plasma Display

STANDBY indicator

POWER ON indicator

POWER button

(right view)

STANDBY/ON button

Turning on the power

Press POWER on the Plasma Display.

• The STANDBY indicator on the Plasma Display flashes red.

Press POWER on the Media Receiver.

• The system is turned on or placed into the standby mode.

Confirm that the STANDBY indicators light up red, and then press any button 0 to 9 or a on the remote control unit or STANDBY/ON on the Plasma Display to turn the system on.

• In the standby mode, when you press 0, the power turns on and the on-screen image comes from the INPUT 1 source. Or, when you press any button from 1 to 9, a TV image displays.

• The POWER ON indicators on the Plasma Display and Media Receiver light up in green.

• In this manual, “system” mean the Plasma Display Panel and Media Receiver.

•You can also reverse steps 1 and 2.

English

Media Receiver

POWER

ON STANDBY

POWER ON indicator

POWER button

STANDBY indicator

Turning off the power

Press a on the remote control unit or STANDBY/ ON on the Plasma Display.

• The system enters standby mode and the image on the screen disappears.

• Both STANDBY indicators light up in red.

Press POWER on the Media Receiver.

• The STANDBY indicator on the Media Receiver turns off and the one on the Plasma Display flashes red.

Press POWER on the Plasma Display.

• The STANDBY indicator on the Plasma Display turns off.

•You can also reverse steps 2 and 3.

• If you are not going to use this system for a long period of time, be sure to remove the power cord from the power outlet.

• When the system is placed into the standby mode, the main power flow is cut and the system is no longer fully operational. A minute flow of power feeds the system to maintain operation readiness.

ENTER

07 Watching TV

Plasma Display/Media Receiver status indicators

Indicator Status System Status

Plasma Display Media Receiver

POWER ON STANDBY POWER ON STANDBY

Flashing

For other than the above, see “Troubleshooting” on page 63.

Flashing

Power to the Plasma Display and Media Receiver is off. Or the power cords have been disconnected.

Power to the system is on.

The system is in the standby mode.

Power to the Media Receiver is off. Or the power cord has been disconnected from the Media Receiver.

Power to the Plasma Display is off. Or the power cord has been disconnected from the Plasma Display.

CHANNEL +/–

Plasma Display (right view)

ENTER

Changing channels

Using P +/– on the remote control unit

•Press P + to increase the channel number.

•Press P – to decrease the channel number.

When viewing Teletext information:

•Press P + to increase the page number.

•Press P – to decrease the page number.

• CHANNEL +/– on the Plasma Display operates the same as P +/–.

Using 0 – 9 on the remote control unit

Select channels directly by pressing buttons 0 to 9.

EXAMPLE

•To select channel 2 (1-digit channel), press 2.

•To select channel 12 (2-digit channel), press 1 then 2.

When viewing Teletext information:

View a page directly which is 3-digit page number from 100 to 899 by pressing buttons 0 to 9.

Channel display

AAA

STEREO

STANDARD

FULL

•After entering a channel or subchannel number, you may press CH ENTER to tune in the channel more quickly.

• In the standby mode, when you press 0, the power turns on and the on-screen image comes from the INPUT 1 source. Or, when you press any button from 1 to 9, a TV image displays.

07Watching TV

VOLUME +/–

Plasma Display (right view)

ENTER

Changing the volume and sound

Using i +/– on the remote control unit

•To increase the volume, press i +.

•To decrease the volume, press i –.

• VOLUME +/– on the Plasma Display operates the

same as i +/–.

Using e on the remote control unit

e mutes the current sound output.

Press e.

•“M” appears on the screen.

Press e again to cancel the mute mode.

•Pressing i + can also cancel the mute mode.

English

Volume adjustment

Muting

07 Watching TV

Using g on the remote control unit

ENTER

NICAM Broadcasts

Stereo

Bilingual

Monaural

Stereo

NICAM STEREO

AAA

BBB

NICAM p

CCC

NICAM MONO

DDD

STEREO

Each time you press g, MTS toggles as shown below.

mode

ppp

mode MONO mode

MONO

Setting

MONOppp

AAA

NICAM STEREO

BBB

NICAM pp

CCC

NICAM MONO

DDD

STEREO

AAA

MONO

BBB

MONO

CCC

MONO

DDD

MONO

A2 Broadcasts

Bilingual

Monaural

Stereo

MAIN+SAP

BTSC Broadcasts

Stereo+SAP

Monaural

• In each of the sound multiplex mode selected using the g button, the display changes depending on broadcasting signals being received.

• Once the MONO mode is selected, the Plasma Display System sound remains mono even if the system receives a stereo broadcast. You must switch the mode back to p or pp mode if you want to hear

stereo sound again.

EEE

DUAL p

FFF

MONO

GGG

STEREO

HHH

MAIN(SAP)

JJJ

STEREO(SAP)

KKK

MONO

EEE

DUAL pp

FFF

MONO

GGG

STEREO

HHH

SAP(MAIN)

JJJ

SAP(STEREO)

KKK

MONO

EEE

MONO

FFF

MONO

GGG

MONO

HHH

MONO

JJJ

MONO

KKK

MONO

• Selecting a sound multiplex mode while the input source is INPUT 1 to 4 or PC does not change the type of sound. In this case, sound is determined by the video source.

Using the multiscreen functions

Splitting the screen

Use the following procedure to select the 2-screen or picture-in-picture mode.

ENTER

• The multiscreen function cannot display images from

the same input source at the same time. If you make such an attempt, a warning message appears.

• When you press HOME MENU, the single-screen

mode is restored and the corresponding menu is displayed.

• When in the 2-screen mode, images displayed on the

right screen may look less fine, depending on images.

Freezing images

Use the following procedure to capture and freeze one frame from a moving image that you are watching.

07Watching TV

English

2-screen

Picture-in-picture

Press

c to select the display mode.

• Each time you press switched among 2-screen, picture-in-picture, and single-screen.

Press / to select a screen to be active.

•“

z” appears on the active screen, which outputs

sound.

To select the desired input source, press the appropriate input source button.

If watching TV programs, press P+/P– to change the channel.

c, the display mode is

Normal image Still image

Press d.

•A still image appears on the right screen while a moving image is shown on the left screen.

Press d again to cancel the function.

•With the screen split, any image cannot be frozen.

• When this function is not available, a warning message appears.

08 Basic Adjustment Settings

Using the menu

AV mode menus

Home Menu Item Description Page

Picture AV Selection Select from the five display mode options; STANDARD, DYNAMIC, MOVIE,

Contrast Adjusts the picture between light and shade. 36 Brightness Adjusts picture brightness. 36 Color Adjusts color intensity. 36 Tint Adjusts skin color to a more natural tone for all color system. 36 Sharpness Adjusts picture sharpness. 36 Pro Adjust

Reset All image adjustment settings return to the factory defaults. 36

Sound Tr eble Adjusts the treble weaker or stronger. 41

Bass Adjusts the bass weaker or stronger. 41 Balance Adjusts audio output between left and right speakers. 41 Reset All audio adjustment settings return to the factory defaults. 41 FOCUS Shift the sound coming direction (sound images) upward and produces clear

Front Surround Provides three-dimensional sound effects and/or deep, rich bass. 42

GAME, and USER. 35

Adjusts the levels of PureCinema, Color Temp, MPEG NR, DNR, CTI, DRE, and Color Management.

sound contours. 41

37–40

Power Control Energy Save Saves power by decreasing picture brightness. 42

No Signal off Places the system into the standby mode when no signal is received for

No Operation off Places the system into the standby mode when no operation is performed

Sleep Timer Automatically places the system into the standby mode when the selected

Option Position Adjusts the vertical and horizontal positions of displayed images. 56

WSS Allows you to view information in the wide screen mode when wide screen

4:3 Mode Select the aspect ratio of video signals. 60 Color System Select the color system compatible with images on the screen. 57 Side Mask With the 4:3 screen size selected, sets the brightness of the gray side masks

HDMI Input Allows the HDMI terminal to accept digital video and audio signals. 53

Setup Auto Installation Allows you to set up TV channels and select a language to be used for

Program Setup Sets up TV channels. 31–34 Password Prevents other persons from changing important settings. 61–62 Language Select the language to be used for on-screen display such as menus and

15 minutes. 43

for three hours. 43

time elapses. 61

signals are included in Teletext data. 59

that appear at both sides of the screen. 60

on-screen display. 30

instructions and the one to be used in the TELETEXT mode. 34

PC mode menus

Home Menu Item Description Page

Picture AV Selection Select from the two display mode options; STANDARD and USER. 35

Contrast Adjusts the picture between light and shade. 36 Brightness Adjusts picture brightness. 36 RedAdjusts red color intensity. 36 Green Adjusts green color intensity. 36 Blue Adjusts blue color intensity. 36 Reset All image adjustment settings return to the factory defaults. 36

Sound Tr eble Adjusts the treble weaker or stronger. 41

Bass Adjusts the bass weaker or stronger. 41 Balance Adjusts audio output between left and right speakers. 41 Reset All audio adjustment settings return to the factory defaults. 41 FOCUS Shifts the sound coming direction (sound images) upward and produces

clear sound contours. 41

Front Surround Provides three-dimensional sound effects and/or deep, rich bass. 42

Power Control Energy Save Saves power by decreasing picture brightness. 42

Power Management Automatically places the system into the standby mode when no signal is

received from the personal computer. 44

08Basic Adjustment Settings

English

Sleep Timer Automatically places the system into the standby mode when the selected

Option Auto Setup Automatically optimizes image positions and clock. 56

Manual Setup Allows you to manually adjust image positions and clock. 57

time elapses. 61

08 Basic Adjustment Settings

Menu operation keys

Use the following keys on the remote control to operate the menu. For detailed menu operations, see appropriate pages that describe individual functions.

HOME MENU:Press to open or close the Home

menu.

/ :Press to select a menu item. For

some menu items, you can select parameters using these keys.

/ :Press to select a parameter or adjust-

ment level for menu items.

ENTER:Press to proceed to lower menu

levels. For some menu items, you need to press this key to complete selections.

RETURN:Press to return to upper menu levels.

Press / to select “Channel Allocation”, and then press / to select “Normal”, “Air (US Type)” or “Cable (US Type)”.

• The table in page 65 shows which option you should usually select in your country or region.

Item Description

Normal Scans to locate your regional broadcasting

Air (US Type) Searches for the same broadcasting

Cable (US Type) Searches for the same broadcasting

Auto Installation

Language

Channel Allocation

Installation

frequencies. The earlier the frequencies identified, the smaller the channel numbers used.

frequencies as for receiving over air in the U.S. This selection is effective when the system is receiving over air.

frequencies as for watching cable TV in the U.S. This selection is effective when the system is receiving from a cable TV company.

English

Air (US Type)

Setting up TV channels automatically

This section describes how to automatically search and set up TV channels.

Using Auto Installation

When the Plasma Display System is switched on for the first time after purchase, the initial auto installation is initiated. You can automatically set language, country and channels in successive operations.

Press / to select “Language”, and then press

/ to select a language.

Auto Installation

Language

Channel Allocation

Installation

•You can select from among five languages; English, Spanish, Portuguese, Traditional chinese and Simplified chinese.

English

Cable (US Type)

Start

Press / to select “Start”, and then press ENTER.

• Auto Installation automatically starts.

•To quit Auto Installation in progress, press

RETURN.

After Auto Installation has been finished, press HOME MENU to exit the menu.

•You can start Auto Installation from the Home menu after moving to another country, for example. Before doing steps 1 to 4 above, do the following steps 1 to 3.

1 Press HOME MENU. 2 Press / to select “Setup”, and then press

ENTER.

3 Press / to select “Auto Installation”, and then

press ENTER.

• The password entry screen appears. Enter your 4-digit password using buttons 0 – 9.

• If no channel is found, check the antenna connections, and then retry Auto Installation.

+ 235 hidden pages