Pioneer DV-393 Owners manual

DVD Player

DV-290-K DV-393-S DV-490V-S DV-490V-K

www.pioneerelectronics.com (US) www.pioneerelectronics.ca (Canada)

Operating Instructions

The lightning flash with arrowhead, within

an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D1-4-2-3_En

IMPORTANT NOTICE – THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED IN THE REAR.

PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND KEEP IN A SECURE AREA. THIS IS FOR YOUR SECURITY.

D1-4-2-6-1_En

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help.

D8-10-1-2_En

CAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION : THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.

D6-8-2-1_En

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

CAUTION – TO PREVENT ELECTRIC SHOCK DO

NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD.

RECEPTACLE OR OTHER OUTLET

WARNING – TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

D8-10-2_En

D1-4-2-1_En

UNLESS THE BLADES CAN BE

WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to lead, a chemical known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm.

Wash hands after handling

D36-P4_En

ATTENTION –

FULLY INSERTED TO PREVENT BLADE EXPOSURE. POUR PREVENIR LES CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVVERT.

D2-4-4-1_EF

his product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance : www.eiae.org.

K057_En

READ INSTRUCTIONS — All the safety and

operating instructions should be read before the product is operated.

RETAIN INSTRUCTIONS — The safety and

operating instructions should be retained for future reference.

HEED WARNINGS — All warnings on the product

and in the operating instructions should be adhered to.

FOLLOW INSTRUCTIONS — All operating and use

instructions should be followed.

CLEANING — The product should be cleaned only

with a polishing cloth or a soft dry cloth. Never clean with furniture wax, benzine, insecticides or other volatile liquids since they may corrode the cabinet.

ATTA CHMENTS — Do not use attachments not

recommended by the product manufacturer as they may cause hazards.

WATER AND MOISTURE — Do not use this

product near water — for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

ACCESSORIES — Do not place this product on an

unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

CART — A product and cart combination should be

moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

VENTILATION — Slots and openings in the cabinet

are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

POWER SOURCES — This product should be

operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

LOCATION – The appliance should be installed in a

stable location.

NONUSE PERIODS – The power cord of the

appliance should be unplugged from the outlet when left un-used for a long period of time.

GROUNDING OR POLARIZATION

• If this product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other), it will fit into the outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

• If this product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin, it will only fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug.

POWER-CORD PROTECTION — Power-supply

cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

OUTDOOR ANTENNA GROUNDING — If an

outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.

LIGHTNING — For added protection for this

product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

POWER LINES — An outside antenna system

should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

OVERLOADING — Do not overload wall outlets,

extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

ELECTRIC SERVICE EQUIPMENT

Fig. A

OBJECT AND LIQUID ENTRY — Never push

objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

SERVICING — Do not attempt to service this

product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

DAMAGE REQUIRING SERVICE — Unplug this

product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

• When the power-supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

• If the product has been dropped or damaged in any way.

• When the product exhibits a distinct change in performance — this indicates a need for service.

REPLACEMENT PARTS — When replacement parts

are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

SAFETY CHECK — Upon completion of any service

or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

WALL OR CEILING MOUNTING — The product

should not be mounted to a wall or ceiling.

HEAT — The product should be situated away from

heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

ANTENNA LEAD IN

GROUND CLAMP

WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

NEC — NATIONAL ELECTRICAL CODE

D1-4-2-2_En

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

D8-10-1-3_EF

CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the

unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.

D8-10-3a_En

For U.S. and Australia Model

C67-7-3_En

This product includes FontAvenue® fonts licenced by NEC corporation. FontAvenue is a registered trademark of NEC Corporation.

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period. K041_En

We Want You Listening For A Lifetime

Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing damage from loud noise is often undetectable until it is too late, this manufacturer

Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion-and, most importantly, without affecting your sensitive hearing.

Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.

To establish a safe level:

• Start your volume control at a low setting.

• Slowly increase the sound until you can hear it

comfortably and clearly, and without distortion.

Once you have established a comfortable sound level:

• Set the dial and leave it there.

Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all, we want you listening for a lifetime.

and the Electronic Industries Association’s Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise. This list of sound levels is included for your protection.

Decibel Level Example

30 Quiet library, soft whispers

Living room, refrigerator, bedroom away from traffic

40 50 Light traffic, normal conversation, quiet office 60 Air conditioner at 20 feet, sewing machine 70 Vacuum cleaner, hair dryer, noisy restaurant 80

Average city traffic, garbage disposals, alarm clock

at two feet.

THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE

Subway, motorcycle, truck traffic, lawn mower 100 Garbage truck, chain saw, pneumatic drill 120 Rock band concert in front of speakers,

thunderclap 140 Gunshot blast, jet plane 180 Rocket launching pad

Information courtesy of the Deafness Research Foundation.

S002_En

S001_En

Thank you for buying this Pioneer product.

Please read through these operating instructions so that you will know how to operate your model properly. After you have finished reading the instructions, put them in a safe place for future reference

Contents

01 Before you start

Features What’s in the box Hints on installation

Disc / content format playback compatibility

. . . . . . . . . . . . . . . . . . . . . . . . . . . 6

. . . . . . . . . . . . . . . . . . . . 7

. . . . . . . . . . . . . . . . . . 7

. . . . . . . . . . . . . . . . . . . . . . . 8

02 Connecting up

Easy connections Connecting using the S-video output Connecting using the component video

. . . . . . . . . . . . . . . . . . . . . . . . . . . 12

output Connecting to an AV receiver Connecting using HDMI (DV-490V only) About HDMI

. . . . . . . . . . . . . . . . . . . 11

. . . . 12

. . . . . . . . . . 13

. . . . . . . . . . . . . . . . . . . . . . . 15

03 Controls and displays

Front panel Remote control

. . . . . . . . . . . . . . . . . . . . . . . . 16

. . . . . . . . . . . . . . . . . . . . 17

04 Getting started

Switching on Using the on-screen displays Setting up the player for your TV Setting the language of this player’s on-screen displays Playing discs

. . . . . . . . . . . . . . . . . . . . . . 18

. . . . . . . . . . 18

. . . . . . . . 19

. . . . . . . . . . . . . . . . . . 19

. . . . . . . . . . . . . . . . . . . . . . 20

05 Playing discs

Scanning discs Playing in slow motion Frame advance/frame reverse Viewing a JPEG slideshow Browsing DVD or Video CD disc with the Disc Navigator Browsing WMA, MP3, DivX video and JPEG files with the Disc Navigator Looping a section of a disc

. . . . . . . . . . . . . . . . . . . . 24

. . . . . . . . . . . . . . . 24

. . . . . . . . . 25

. . . . . . . . . . . . 25

. . . . . . . . . . . . . . . . . . 25

. . . . . . 26

. . . . . . . . . . . . 27

. . 14

Using repeat play Using random play Creating a program list Searching a disc Switching subtitles Switching audio language/channels Zooming the screen Switching camera angles Displaying disc information

. . . . . . . . . . . . . . . . . . . .27

. . . . . . . . . . . . . . . . . .28

. . . . . . . . . . . . . . .29

. . . . . . . . . . . . . . . . . . . .30

. . . . . . . . . . . . . . . . . .30

. . . . .31

. . . . . . . . . . . . . . . . . .31

. . . . . . . . . . . . .31

. . . . . . . . . . . .31

06 Audio Settings and Video Adjust menus

Audio Settings menu Video Adjust menu

. . . . . . . . . . . . . . . . .32

. . . . . . . . . . . . . . . . . .33

07 Initial Settings menu

Using the Initial Settings menu Digital Audio Out settings Video Output settings Language settings Display settings Options settings Parental Lock

. . . . . . . . . . . . . . . .35

. . . . . . . . . . . . . . . . . . .36

. . . . . . . . . . . . . . . . . . . . .37

. . . . . . . . . . . . . . . . . . . .37

. . . . . . . . . . . . . . . . . . . . . .38

. . . . . . . . .34

. . . . . . . . . . . . .34

08 Additional information

Taking care of your player and discs Screen sizes and disc formats Resetting the player DVD-Video regions Selecting languages using the language code list Glossary Language code list Country/Area code list

Specifications . . . . . . . . . . . . . . . . . . . . . . 47

. . . . . . . . . . . . . . . . . . . . . . . . . . .42

. . . . . . . . . . . . . . . . . . . . . . . . . .44

. . . . . . . . . . . . . . . . . .42

. . . . . . . . . . . . . . . . . .46

. . . . . . . . . . . . . . . .46

. . . . .40

. . . . . . . . . .41

Before you start01

Chapter 1

Before you start

Features

• 24-bit/96 kHz compatible DAC

The integrated 24-bit/96 kHz DAC means that this player is compatible with high samplingrate discs, capable of delivering exceptional sound quality in terms of dynamic range, lowlevel resolution and high-frequency detail.

•Surround sound entertainment with Dolby Digital

Logos:

When connected to a suitable AV amplifier or receiver, this player gives great surround sound with Dolby Digital and DTS discs.

• PureCinema Progressive Scan video

When connected to a progressive scancompatible TV or monitor using the component video outputs, you can enjoy extremely stable, flicker free images, with the same frame refresh rate as the original movie.

• New Disc Navigator with moving pictures

The new Disc Navigator enables you play the first few seconds of each title or chapter in a thumbnail image on screen.

HDMI*3 digital interface (DV-490V only)

The HDMI (High Definition Multimedia Interface) interconnect provides high quality digital audio and video, all from a single userfriendly connector. HDMI is the first consumer electronics interface to support uncompressed standard, enhanced, or high-definition video plus standard to multi-channel surround

sound audio

and DTS*2 software

, all using one interface. You can

easily connect to a HDMI-equipped AV receiver or audiovisual device for high quality audio and video, and communication between the video source and (DTV) players, set-top boxes, and other audiovisual devices is also supported.

• DSP effects for enhanced playback

See

Audio Settings and Video Adjust menus

page 32.

• Picture zoom

See

Zooming the screen

• MP3 and WMA compatibility

See

Compressed audio compatibility

• JPEG compatibility

See

JPEG file compatibility

• DivX

See

Logos:

• Energy saving design

An auto power-off function switches the player into standby if not used for about 30 minutes.

Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

trademarks of Digital Theater Systems, Inc.

Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.

video compatibility

DivX video compatibility

Manufactured under license from Dolby

“DTS” and “DTS Digital Out” are registered

HDMI, the HDMI logo and High-Definition

on page 31.

on page 10.

on page 9.

Before you start

It is not possible to output SACD or DVDAudio sources from the HDMI connection of this player.

DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.

What’s in the box

Please confirm that the following accessories are in the box when you open it.

• Remote control

• AA/R6P dry cell batteries x 2

• Audio/video cable (red/white/yellow plugs)

• Operating instructions

• Warranty card

Putting the batteries in the remote

• Open the battery compartment cover and insert the batteries as shown.

Use two AA/R6P batteries and follow the indications ( Close the cover when you’re finished.

Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following:

• Don’t mix new and old batteries together.

• Don’t use different kinds of battery together—although they may look similar, different batteries may have different voltages.

• Make sure that the plus and minus ends of each battery match the indications in the battery compartment.

, 

Important

) inside the compartment.

• Remove batteries from equipment that isn’t going to be used for a month or more.

• When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.

• Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.

Hints on installation

We want you to enjoy using this product for years to come, so please use the following guidelines when choosing a suitable location:

Do...

• Use in a well-ventilated room.

• Place on a solid, flat, level surface, such as a table, shelf or stereo rack.

Don’t...

• Use in a place exposed to high temperatures or humidity, including near radiators and other heat-generating appliances.

• Place on a window sill or a place where the player will be exposed to direct sunlight.

• Use in an excessively dusty or damp environment.

• Place directly on top of an amplifier, or other component in your stereo system that becomes hot in use.

• Use near a television or monitor as you may experience interference—especially if the television uses an indoor antenna.

• Use in a kitchen or other room where the player may be exposed to smoke or steam.

Before you start01

• Use on a thick rug or carpet, or cover with cloth—this may prevent proper cooling of the unit.

• Place on an unstable surface, or one that is not large enough to support all four of the unit’s feet.

Disc / content format playback compatibility

This player is compatible with a wide range of disc types (media) and formats. Playable discs will generally feature one of the following logos on the disc and/or disc packaging. Note however that some disc types, such as recordable CD and DVD, may be in an unplayable format—see below for further compatibility information.

Please also note that recordable discs cannot be recorded using this player.

DVD-Video DVD-R DVD-RW

Audio CD CD-R

Video CD

CD-RW

• is a trademark of Fuji Photo Film Co. Ltd.

• Also compatible with KODAK Picture CD

This player supports the IEC’s Super VCD standard. Compared to the Video CD standard, Super VCD offers superior picture quality, and allows two stereo soundtracks to be recorded. Super VCD also supports the widescreen size.

About DualDisc playback

A DualDisc is a new two -sided disc, one side of which contains DVD content video, audio, etc. while the other side contains non-DVD content such as digital audio material.

The non-DVD, audio side of the disc is not compliant with the CD Audio specification and therefore may not play.

The DVD side of a DualDisc plays in this product.

For more detailed information on the DualDisc specification, please refer to the disc manufacturer or disc retailer.

CD-R/RW compatibility

• Compatible formats: CD-Audio, Video CD, ISO 9660 CD-ROM* containing MP3, WMA, JPEG or DivX video files *

ISO 9660 Level 1 or 2 compliant. CD physical format: Mode1, Mode2 XA Form1. Romeo and Joliet file systems are both compatible with this player.

• Multi-session playback: No

• Unfinalized disc playback: No

• File structure (may differ): Up to 299 folders on a disc; up to 648 folders and files (combined) within each folder

Fujicolor CD

• This unit will play DVD+R/+RW discs.

•

is a trademark of DVD Format/Logo

Licensing Corporation.

Before you start

DVD+R/DVD+RW compatibility

Only DVD+R/DVD+RW discs recorded in ‘Video Mode (DVD Video Mode)’ which have been finalized, can be played back. However, some editing made during the recording may not be played back accurately.

DVD-R/RW compatibility

• Compatible formats: DVD-Video, Video Recording (VR)* *

Edit points may not play exactly as edited; screen may go momentarily blank at edited points.

• Unfinalized playback: No

• WMA/MP3/JPEG file playback on DVD-R/ RW: No

Compressed audio compatibility

• Compatible formats: MPEG-1 Audio Layer 3 (MP3), Windows Media Audio (WMA)

• Sampling rates: 32 kHz, 44.1 kHz or 48 kHz

• Bit-rates: Any (128 Kbps or higher recommended)

• VBR (variable bit rate) MP3 playback: No

• VBR WMA playback: No

• WMA lossless encoding compatible: No

• DRM (Digital Rights Management) compatible: Yes (DRM-protected audio files will

DRM

• File extensions: .mp3, .wma (these must be used for the player to recognize MP3 and WMA files – do not use for other file types)

not

play in this player—see also

in the

Glossary

on page 44)

About WMA

The Windows Media® logo printed on the box indicates that this player can playback Windows Media Audio content.

WMA is an acronym for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA content can be encoded by using Windows

Media

Player version 7, 7.1, Windows Media®

Player for Windows Player 9 Series.

Microsoft, Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/ or other countries.

XP, or Windows Media®

About DivX

DivX is a media technology created by DivX, Inc. DivX media files contain compressed video. DivX files can also include advanced media features like menus, subtitles, and alternate audiotracks. This player can play DivX video files burned on CD-R/RW/ROM discs. Keeping the same terminology as DVD-Video, individual DivX video files are called "Titles". When naming files/titles on a CD-R/RW disc prior to burning, keep in mind that by default they will be played in alphabetical order.

Before you start01

Displaying DivX subtitle files

The font sets listed below are available for DivX external subtitle files. You can see the proper font set on-screen by setting the

Language

(in

Language settings

Subtitle

on page 36)

to match the subtitle file.

This player supports the following language groups:

Group 1: Albanian (sq), Basque (eu), Catalan (ca),

Danish (da), Dutch (nl), English (en), Faroese (fo), Finnish (fi), French (fr), German (de), Icelandic (is), Irish (ga), Italian (it), Norwegian (no), Portuguese (pt), RhaetoRomanic (rm), Scottish (gd), Spanish (es), Swedish (sv)

Group 2: Albanian (sq), Croatian (hr), Czech (cs),

Hungarian (hu), Polish (pl), Romanian (ro), Slovak (sk), Slovenian (sl)

Group 3: Bulgarian (bg), Byelorussian (be), Macedonian

(mk), Russian (ru), Serbian (sr), Ukrainian (uk)

Group 4: Hebrew (iw), Yiddish (ji) Group 5: Turkish (tr)

• Some external subtitle files may be displayed incorrectly or not at all.

• For external subtitle files the following subtitle format filename extensions are supported (please note that these files are not shown within the disc navigation menu): .srt, .sub, .ssa, .smi

• The filename of the movie file has to be repeated at the beginning of the filename for the external subtitle file.

• The number of external subtitle files which can be switched for the same movie file is limited to a maximum of 10.

DivX video compatibility

• Plays all versions of DivX

6) with standard playback of DivX®

DivX

video (including

media files.

• File extensions: .avi and .divx (these must be used for the player to recognize DivX video files).

Note that all files with the .avi extension are recognized as MPEG4, but not all of these are necessarily DivX video files and therefore may not be playable on this player.

DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.

JPEG file compatibility

• Compatible formats: Baseline JPEG and EXIF 2.2* still image files up to a resolution of 3072 x 2048. *

File format used by digital still cameras.

• Progressive JPEG compatible: No

• File extensions: .jpg (must be used for the player to recognize JPEG files – do not use for other file types)

PC-created disc compatibility

Discs recorded using a personal computer may not be playable in this unit due to the setting of the application software used to create the disc. In these particular instances, check with the software publisher for more detailed information.

Discs recorded in packet write mode (UDF format) are not compatible with this player.

Check the DVD-R/RW or CD-R/RW software disc boxes for additional compatibility information.

• Official DivX® Certified product.

Connecting up

Chapter 2

Connecting up

Easy connections

• Before making or changing any connections, switch off the power and disconnect the power cable from the AC outlet.

• The setup described here is a basic setup that allows you to play discs using just the cables supplied with the player. In this setup, stereo audio is played through the speakers in your TV.

• The following illustrations show the DV-393, but connections for the DV-490V are the same except where indicated.

A/V IN

VIDEO OUT

COAXIAL

S-VIDEO

OUT

COMPONENT VIDEO OUTDIGITAL AUDIO OUT

AUDIO OUT

Yel low

White

Red

To power

outlet

Important

• This player is equipped with copy protection technology. Do not connect this player to your TV via a VCR using audio/video or S-video cables, as the picture from this player will not appear properly on your TV. (This player may also not be compatible with some combination TV/VCRs for the same reason; refer to the manufacturer for more information.)

• When connecting to your TV as shown above, do not set the

Video Output settings

on page 35) to

Progressive

Component Out

setting (See

Connecting up02

S-VIDEO

OUT

AUDIO OUT

COAXIAL

COMPONENT VIDEO OUTDIGITAL AUDIO OUT

VIDEO OUT

S-VIDEO

OUT

AUDIO OUT

COAXIAL

COMPONENT VIDEO OUTDIGITAL AUDIO OUT

VIDEO OUT

1 Connect the VIDEO OUT and AUDIO OUT L/R jacks to a set of A/V inputs on your TV.

Use the supplied audio/video cable, connecting the red and white plugs to the audio outputs and the yellow plug to the video output. Make sure you match up the left and right audio outputs with their corresponding inputs for correct stereo sound.

See below if you want to use a component or S-video cable for the video connection.

2Plug into a power outlet.

Note

• Before unplugging the player from the power outlet, make sure you first switch it into standby using either the front panel

STANDBY/ON

control, and wait of the

button, or the remote

-OFF-

message to



disappear from the player’s display.

• For the above reasons, do not plug this player into a switched power supply found on some amplifiers and AV receivers.

Connecting using the S-video output

If your TV (or other equipment) has an S-video (S1) input, you can use the S-video output on this player instead of the standard (composite) output for a better quality picture.

• Use an S-video cable (not supplied) to connect the S-VIDEO OUT to an S-video input on your TV (or monitor or AV receiver).

Line up the small triangle above the jack with the same mark on the plug before plugging in.

S-VIDEO

Connecting using the component video output

You can use the component video output instead of the standard video out jack to connect this player to your TV (or other equipment). This should give you the best quality picture from the three types of video output available.

• Use a component video cable (not supplied) to connect the COMPONENT VIDEO OUT jacks to a component video input on your TV, monitor or AV receiver.

COMPONENT

VIDEO IN

Connecting up

Watching progressive scan video from the component video outputs

This player can output progressive scan video from the component video output. Compared to interlace video, progressive scan video effectively doubles the scanning rate of the picture, resulting in a very stable, flicker-free image.

To set up the player for use with a progressive scan TV, see When the player is set to output progressive scan video, the front panel display.

• When

Progressive

the video) jacks.

• If you want to display video on more than one monitor simultaneously, make sure the player is set to

• If you connect a TV that is not compatible with a progressive scan signal and switch the player to progressive, you will not be able to see any picture at all. In this case, switch everything off and reconnect using the supplied video cable (see

connections

Video Output settings

PRGSVE

Important

Component Out

, there is no video output from

VIDEO OUT

on page 11), then switch back

Interlace

(see below).

on page 35.

indicator lights in the

(page 35) is set to

(composite) and S (S-

Interlace

Easy

resolution will be reset to its default—see

Resetting the output resolution to the default setting with HDMI connection

page 15.)

 STANDBY/ON

DV-490V



Connecting to an AV receiver

To enjoy multichannel surround sound you need to connect this player to an AV receiver using the digital audio output.

In addition to a digital connection, we recommend also connecting using the stereo analog connection.

You’ll probably also want to connect a video output to your AV receiver. You can use any of the video outputs available on this player (the illustration shows a standard (composite) connection).

Switching the video output to interlace using the front panel controls

Switch the player to standby then, using the front panel controls, press while pressing

Interlace

DV-490V only:

• using HDMI, disconnect the HDMI cable before resetting the player to interlace output. (If left connected, the HDMI output



If the player is connected



STANDBY/ON

to switch the player back to

Connecting up02

S-VIDEO

OUT

AUDIO OUT

COAXIAL

COMPONENT VIDEO OUTDIGITAL AUDIO OUT

VIDEO OUT

S-VIDEO OUT

AUDIO OUT

COAXIAL

COMPONENT VIDEO OUT

DIGITAL AUDIO OUT

VIDEO OUT

HDMI OUT

S-VIDEO

OUT

AUDIO OUT

COAXIAL

COMPONENT VIDEO OUTDIGITAL AUDIO OUT

VIDEO OUT

S-VIDEO OUT

AUDIO OUT

COAXIAL

COMPONENT VIDEO OUT

DIGITAL AUDIO OUT

VIDEO OUT

HDMI OUT

1 Connect the DIGITAL AUDIO OUT COAXIAL jack on this player to a coaxial digital input on your AV receiver.

DIGITAL IN

AV receiver

DV-490V

AV receiver

DV-393

Use a coaxial cable (similar to the supplied video cable) to connect the

AUDIO OUT

jack to a coaxial input on your AV

COAXIAL DIGITAL

receiver.

2 Connect the analog AUDIO OUT L/R and VIDEO OUT jacks on this player to a set of analog audio and video inputs on your AV receiver.

(COAXIAL)

DIGITAL IN (COAXIAL)

AV receiver AUDIO/

VIDEO IN

• You can use the S-video or component video jacks to connect to the AV receiver if you prefer.

Connecting using HDMI (DV490V only)

If you have a HDMI equipped monitor or display, you can connect it to this player using a commercially available HDMI cable.

The HDMI connector outputs uncompressed digital video, as well as almost every kind of digital audio that the player is compatible with, including DVD-Video, Video CD/Super VCD, CD and MP3.

1 Use an HDMI cable to connect the HDMI OUT interconnect on this player to an HDMI interconnect on a HDMI-compatible monitor.

HDMI

connector

HDMI-compatible display

Connecting up

• The arrow on the cable connector body should be face up for correct alignment with the connector on the player.

Note

• This unit has been designed to be compliant with HDMI (High Definition Multimedia Interface) . Depending on the component you have connected, using a DVI connection may result in unreliable signal transfers.

• When you change the component connected to the HDMI output, you will also need to change the HDMI settings to match the new component (see on page 35, and However, the settings for each component are then stored in memory (for up to 2 components).

• The HDMI connection is compatible with

44.1 kHz/48 kHz, 16 bit/20 bit/24 bit 2 channel linear PCM signals, as well as Doldy Digital, DTS and MPEG audio bitstream.

HDMI Resolution

HDMI Color

on page 36 to do this).

HDMI Out

on page 36

Visual Interface (DVI) in one specification. HDCP is used to protect digital content transmitted and received by DVI-compliant displays.

HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multi-channel surround-sound audio. HDMI features include uncompressed digital video, a bandwidth of up to 2.2 gigabytes per second (with HDTV signals), one connector (instead of several cables and connectors), and communication between the AV source and AV devices such as DTVs.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.

Resetting the output resolution to the default setting with HDMI connection

Switch the player to standby then, using the front panel controls, press while pressing

480P





STANDBY/ON

to switch the player back to

 STANDBY/ON

DV-490V



About HDMI

HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for use with DVD players, DTV, set-top boxes, and other AV devices. HDMI was developed to provide the technologies of High Bandwidth Digital Content Protection (HDCP) as well as Digital

+ 33 hidden pages