For details, refer to "Important Check Points for Good Servicing".
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2005
K-ZZA. DEC 2005 Printed in Japan
1234
SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
A
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
- Safety Precautions for those who Service this Unit.
• When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.
Caution:
B
1. During repair or tests, minimum distance of 13cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by the manufacture.
C
Discord used batteries according to the manufacture's instructions.
- CD Section Precaution
1. You should conform to the regulations governing
the product (safety, radio and noise, and other
regulations), and should keep the safety during
servicing by following the safety instructions
described in this manual.
2. Before disassembling the unit, be sure to turn off
D
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
3. To protect the pickup unit from electrostatic discharge
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the
grating.
CAUTION
E
F
2
1234
DEH-3850MP/XU/ES
5678
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
0 Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
A
B
C
D
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
4.3 CD CORE UNIT(S10.5COMP1)............................................................................................................... 40
5. ELECTRICAL PARTS LIST ............................................................................................................................ 42
6.1 CD ADJUSTMENT................................................................................................................................... 46
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT .................................................... 48
6.4 SYSTEM MICROCOMPUTER TEST PROGRAM ................................................................................... 51
7. GENERAL INFORMATION ............................................................................................................................. 52
7.2.1 IC .......................................................................................................................................................... 56
OTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
• The > mark found on some component parts indicates the importance of the safety factor of the part.
A
Therefore, when replacing, be sure to use parts of identical designation.
• Screw adjacent to mark on the product are used for disassembly.
• For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
2.1 PACKING
B
"
4
C
D
E
F
8
1234
DEH-3850MP/XU/ES
5678
(1) PACKING SECTION PARTS LIST
Mark No.DescriptionPart No.
1Polyethylene BagCEG-162
2Cord AssyXDE7008
3Accessory AssyCEA4850
4Case AssyCXB3520
5Screw AssyCEA3849
6•••••
7ScrewCBA1650
*8Polyethylene BagCEG-127
9ScrewCRZ50P090FTC
10 ScrewTRZ50P080FTC
*11 Polyethylene BagCEG-158
12 HandleCNC5395
13 •••••
14 •••••
Mark No.DescriptionPart No.
15 BushCNV3930
16 Remote Control AssyCXC5719
*17 BatteryCEX1065
18 CartonContrast table(2)
19 Contain BoxContrast table(2)
20 ProtectorYHP5008
21 ProtectorYHP5009
22-1 Owner's ManualContrast table(2)
22-2 Owner's ManualContrast table(2)
22-3 Installation ManualContrast table(2)
22-4 Caution CardCRP1310
*22-5 Warranty CardContrast table(2)
(2) CONTRAST TABLE
DEH-3850MP/XU/ES , DEH-3850MP/XU/CN and DEH-3850MPH/XU/GS are constructed the same except for the
following:
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".
A
Large size
A-b
A-b
SCH diagram
Guide page
FM:-24dBs
AM:-24dBs
A-a
A-a
A-a
CN901
C
A-b
Detailed page
471/16
CD:0.35dBs
FM/AM TUNER UNIT
A-a
B
C
15.000MHz
XIN
VSS
VCC
CD-RESET
NC
NC
SYSTEM CONTROLLER
XOUT
TU
D
VCC
VSS
CE2
CE1
TUNPCK
TUNPDI
E
B
CN1801
F
A
16
1234
DEH-3850MP/XU/ES
15
000MH
VSS
TUNPCK
5678
A
A-b
TUNER AMP UNIT
A
B
>
3A
FM,AM:-2.9dBs
CD:10.45dBs
z
.
XOUT
TROLLER
TUNPDI
TUNPDO
C
332/16
AVCC
VREF
AVSS
600µH
CEK1208 10A
>
D
471/16
FM,AM:23.1dBs
CD:36.45dBs
E
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and
discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
For resistors and capacitors in the circuit diagrams, their resistance
values or capacitance values are expressed in codes: