Pioneer DEH-2200UB User Manual 2

CD RECEIVER AUTORADIO CD RADIO CD

DEH-2200UB

English Français Español

Owner’s Manual

Mode d’emploi

Manual de instrucciones

Presection

Before You Start

Thank you for purchasing this PIONEER product.

To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe WARNINGs and CAUTIONs in this manual.

Please keep the manual in a safe and accessible place for future reference.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

For Canadian model

This Class B digital apparatus complies with Canadian ICES-003.

or other reproductive harm. Wash hands after handling.

CAUTION: USE OF CONTROL OR ADJUSTMENT OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION: THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids.

! Always keep the volume low enough to hear

outside sounds.

! Avoid exposure to moisture. ! If the battery is disconnected or discharged,

any preset memory will be erased.

Important (Serial number)

The serial number is located on the bottom of this unit. For your own security and convenience, be sure to record this number on the enclosed warranty card.

About this unit

The tuner frequencies on this unit are allocated for use in North America. Use in other areas may result in poor reception.

WARNING

Handling the cord on this product or cords associated with accessories sold with the product will expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect

Before You Start

Presection

After-sales service for Pioneer products

Please contact the dealer or distributor from where you purchased this unit for after-sales service (including warranty conditions) or any other information. In case the necessary information is not available, please contact the companies listed below: Please do not ship your unit to the companies at the addresses listed below for repair without advance contact.

U.S.A.

Pioneer Electronics (USA) Inc. CUSTOMER SUPPORT DIVISION P.O. Box 1760 Long Beach, CA 90801-1760 800-421-1404

CANADA

Pioneer Electronics of Canada, Inc. CUSTOMER SATISFACTION DEPARTMENT 300 Allstate Parkway Markham, Ontario L3R 0P2 1-877-283-5901 905-479-4411

purchase details in our files in the event of loss or theft.

! Access owner's manuals, spare parts infor-

mation, service information, and much more.

Demo mode

Important

Failure to connect the red lead (ACC) of this unit to a terminal coupled with ignition switch on/off operations may lead to battery drain.

Demo mode

The demo automatically starts when the ignition switch is set to ACC or ON while the unit is turned off. Turning off the unit does not cancel demo mode. To cancel the demo mode, press DISP/ again to start. Operating the demo while the ignition switch is set to ACC may drain battery power.

/SCRL. Press DISP/ /SCRL

English

For warranty information please see the Limited Warranty sheet included with this unit.

In case of trouble

Should this unit fail to operate properly, please contact your dealer or nearest authorized PIONEER Service Station.

Visit our website

http://www.pioneerelectronics.com

! Learn about product updates (such as firm-

ware updates) for your product.

! Register your product to receive notices

about product updates and to safeguard











































Section

Operating this unit

Head unit

Part Part

1 DISP/

2 SRC/OFF 9 USB port

4 Disc loading slot b 1 to 6

5 h (eject) c a/b/c/d

6 CLOCK d BAND/ESC

/SCRL 8

MULTI-CONTROL

(M.C.)

(detach)

CAUTION

Use an optional Pioneer USB cable (CD-U50E) to connect the USB audio player/USB memory to the USB port. Since the USB audio player/USB memory is projected forward from the unit, it is dangerous to connect directly. Do not use the unauthorized product.

AUX input jack (3.5 mm stereo jack)

(list)

Part Operation

e VOLUME

f MUTE

g AUDIO Press to select an audio function.

h DISP/SCRL

i e Press to pause or resume.

j FUNCTION

LIST/

ENTER

Press to increase or decrease volume.

Press to mute. Press again to unmute.

Press to select different displays. Press and hold to scroll through the text information.

Press to select functions. Press and hold to recall the initial setting menu when the sources are off.

Press to display the disc title, track title, folder, or file list depending on the source. While in the operating menu, press to control functions.

Display indication





  





Remote control

Indicator State

(disc)

(artist)

Main dis-

play section

The disc (album) name is displayed. Album search refinement on the iPod browsing function is in use.

The disc (track) artist name is displayed. Artist search refinement on the iPod browsing function is in use.

! Tuner: band and frequency ! Built-in CD ,USB and iPod:

elapsed playback time and text information

Operating this unit

The track (song) name is displayed.

4 (song)

5 c

(folder) The list function is operated.

7 d

8 LOC The local seek tuning is on.

(loudness)

a 5 (stereo)

(repeat) Track or folder repeat is on.

dom)

(shuf-

fle)

(sound retriever)

A playable audio file has been selected while operating the list. Song search refinement on the iPod browsing function is in use.

An upper tier of folder or menu exists.

A lower tier of folder or menu exists. It flashes when a song/album related to the song currently playing is selected from iPod.

LOUD

The loudness is on.

The selected frequency is being broadcasted in stereo.

(ran-

Random play is on.

Shuffle function is on while the iPod source is being selected.

The sound retriever function is on.

Removing the front panel to protect your unit from theft

1 Press 2 Grab the front panel and remove.

Re-attaching the front panel

1 Slide the front panel to the left until it clicks.

2 Press the right side of the front panel until it is

Turning the unit on 1 Press SRC/OFF to turn the unit on.

Turning the unit off 1 Press SRC/OFF and hold until the unit turns off.

Selecting a source 1 Press SRC/OFF to cycle between:

Adjusting the volume 1 Tur n M.C. to adjust volume.

to release the front panel.

Front panel and the head unit are connected on the left side. Make sure that the front panel has been properly connected to the head unit.

firmly seated. If you can’t attach the front panel to the head unit successfully, try again. However, forcing the front panel into place may result in damage.

TUNER (tuner)—CD (built-in CD player)—USB (USB)/IPOD (iPod)—AUX (AUX)

Section

English

Basic Operations

Important

! Handle gently when removing or attaching

the front panel.

! Avoid subjecting the front panel to excessive

shock.

! Keep the front panel out of direct sunlight and

high temperatures.

! Remove any cables and devices attached to

this unit before detaching the front panel to avoid damage to the device or vehicle interior.

Notes

! When this unit’s blue/white lead is connected

to the vehicle’s auto-antenna relay control terminal, the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the source off.

! In this manual, iPod and iPhone will be re-

ferred to as iPod.

Section

Operating this unit

Use and care of the remote control

Using the remote control 1 Point the remote control in the direction of the

front panel to operate. When using for the first time, pull out the film protruding from the tray.

Replacing the battery 1 Slide the tray out on the back of the remote con-

trol.

2 Insert the battery with the plus (+) and minus (–)

poles aligned properly.

www.dtsc.ca.gov/hazardouswaste/

See perchlorate. (Applicable to California, U.S.A.)”

Important

! Do not store the remote control in high tem-

peratures or direct sunlight.

! The remote control may not function properly

in direct sunlight.

! Do not let the remote control fall onto the

floor, where it may become jammed under the brake or accelerator pedal.

Menu operations identical for function settings/audio adjustments/initial settings/lists

WARNING

! Keep the battery out of the reach of children.

Should the battery be swallowed, consult a doctor immediately.

! Batteries (batter y pack or batteries installed)

must not be exposed to excessive heat such as sunshine, fire or the like.

CAUTION

! Use one CR2025 (3 V) lithium battery. ! Remove the battery if the remote control is not

used for a month or longer.

! There is a danger of explosion if the battery is

incorrectly replaced. Replace only with the same or equivalent type.

! Do not handle the battery with metallic tools. ! Do not store the battery with metallic objects. ! If the battery leaks, wipe the remote control

completely clean and install a new battery.

! When disposing of used batteries, comply

with governmental regulations or environmental public institutions’ rules that apply in your country/area.

! “Perchlorate Material – special handling may

apply.

Returning to the previous display Returning to the previous list/category (the folder/category one level higher) 1 Press DISP/

Returning to the main menu Returning to the top tier of list/category 1 Press and hold DISP/

Returning to the ordinary display Canceling the initial setting menu 1 Press BAND/ESC.

Returning to the ordinary display from the list/category 1 Press BAND/ESC.

/SCRL.

Operating this unit

Tuner

Basic Operations

Selecting a band

1 Press BAND/ESC until the desired band (F1, F2,

F3 for FM or AM) is displayed.

Manual tuning (step by step) 1 Press c or d.

Seeking 1 Press and hold c or d, and then release.

You can cancel seek tuning by briefly pressing c or d. While pressing and holding c or d, you can skip stations. Seek tuning starts as soon as you release c or d.

Storing and recalling stations

You can easily store up to six stations for each band as presets.

% When you find a station that you want to store in memory, press one of the preset tuning buttons (1 to 6) and hold until the preset number stops flashing.

Stored radio station frequency can be recalled by pressing the preset tuning button.

# You can also recall stored radio stations by pressing a or b during the frequency display.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

After selecting, perform the following procedures to set the function.

BSM (best stations memory)

BSM (best stations memory) automatically stores the six strongest stations in the order of their signal strength. 1 Press M.C. to turn BSM on.

To cancel, press M.C. again.

Section

English

LOCAL (local seek tuning)

Local seek tuning lets you tune in only those radio stations with sufficiently strong signals for good reception.

1 Press M.C. to display the setting mode. 2 Tur n M.C. to select the desired setting.

FM: OFF—LEVEL 1—LEVEL 2—LEVEL 3—LEVEL 4

AM: OFF—LEVEL 1—LEVEL 2 Larger setting number is higher level. The highest level setting allows reception of only the strongest stations, while lower settings let you receive progressively weaker stations.

3 Press M.C. to confirm the selection.

Note

Operation is complete even if the menu is cancelled before being confirmed.

CD/CD-R/CD-RW and USB storage devices

Basic Operations

Playing a CD/CD-R/CD-RW 1 Insert the disc, label side up, into the disc loading

slot.

1 If a disc has already been inserted, press SRC/

OFF to select the built-in CD player.

Ejecting a CD/CD-R/CD-RW 1 Press h.

Playing songs on a USB storage device 1 Open the USB connector cover and plug in the

USB storage device using a USB cable.

Stop playing a USB storage device 1 You may disconnect the USB storage device at

anytime.

Selecting a folder 1 Press a or b.

Selecting a track 1 Press c or d.

Fast forwarding or reversing 1 Press and hold c or d.

Section

Operating this unit

Returning to root folder 1 Press and hold BAND/ESC.

Switching between compressed audio and CD-DA 1 Press BAND/ESC.

Notes

! When playing compressed audio, there is no

sound during fast forward or reverse.

! USB portable audio players that can be

charged via USB will be recharged when plugged in and the ignition switch is set to ACC or ON.

! Disconnect USB storage device from unit

when not in use.

! If plug and play is on and a USB storage de-

vice is present, depending on the type of device, the source may switch to USB automatically when you turn on the engine. Please change plug and play setting as necessary. Refer to USB (plug and play) on page 12.

Displaying text information

Selecting the desired text information 1 Press DISP/

CD TEXT discs: Play time—disc title—disc ar- tist name—track title—track artist name

WMA/MP3: Play time—folder name—file name —track title—artist name—album title—com- ment—bit rate—folder and track numbers

WAV: Play time—folder name—file name—sam- pling frequency—folder and track numbers

Scrolling the text information to the left 1 Press and hold DISP/

Notes

! Incompatible text stored with the audio file

may not be displayed or may be displayed incorrectly.

! Depending on the version of iTunes used to

write MP3 files onto a disc, comment information may be incorrectly displayed.

! When playing back VBR (variable bit rate)-re-

corded WMA files, the average bit rate value is displayed.

/SCRL.

! When playing back VBR (variable bit rate)-re-

corded MP3 files, VBR is displayed instead of bit rate value.

Selecting and playing files/ tracks from the name list

1 Press to switch to the file/track name list mode.

2 Use M.C. to select the desired file name (or folder name).

Changing file or folder name 1 Tur n M.C.

Playing 1 When a file or track is selected, press M.C.

Seeing a list of files (or folders) in the selected folder 1 When a folder is selected, press M.C.

Playing a song in the selected folder 1 When a folder is selected, press and hold M.C.

Note

Track title list will display the list of track titles on a CD TEXT disc.

Advanced operations using special buttons

Selecting a repeat play range 1 Press 6/

CD/CD-R/CD-RW

! DISC – Repeat all tracks ! TRACK – Repeat the current track ! FOLDER – Repeat the current folder

USB audio player/USB memory

! TRACK – Repeat the current file ! FOLDER – Repeat the current folder ! ALL – Repeat all files

Playing tracks in random order 1 Press 5/

Tracks in a selected repeat range are played in random order.

to cycle between the following:

to turn random play on or off.

Operating this unit

Pausing playback 1 Press 2/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich sound (sound retriever)

1 Press 1/S.Rtrv to cycle between:

OFF (off)—MODE 1—MODE 2 MODE 1 is effective for low compression rates,

and MODE 2 is effective for high compression rates.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

After selecting, perform the following procedures to set the function.

REPEAT (repeat play)

1 Press M.C. to display the setting mode. 2 Tur n M.C. to select a repeat play range.

For details, refer to Selecting a repeat play range on the previous page.

3 Press M.C. to confirm the selection.

RANDOM (random play)

1 Press M.C. to turn random play on or off.

PAUSE (pause)

1 Press M.C. to pause or resume.

S.RTRV (sound retriever)

Automatically enhances compressed audio and restores rich sound.

1 Press M.C. to display the setting mode. 2 Tur n M.C. to select the desired setting.

For details, refer to Enhancing compressed audio and restoring rich sound (sound retriever) on this

page.

3 Press M.C. to confirm the selection.

Note

Operation is complete even if the menu is cancelled before being confirmed.

iPod

Basic Operations

Playing songs on iPod 1 Open the USB connector cover and plug in an

iPod using the iPod Dock Connector to USB Cable.

Selecting a track (chapter) 1 Press c or d.

Fast forwarding or reversing 1 Press and hold c or d.

Notes

! The iPod’s battery will be charged if the igni-

tion switch is set to ACC or ON, while connected.

! While the iPod is connected to this unit, the

iPod cannot be turned on or off unless the control mode is set to IPOD.

! Disconnect headphones from the iPod before

connecting to this unit.

! The iPod will turn off about two minutes after

the ignition switch is set to OFF.

Displaying text information

Selecting the desired text information 1 Press DISP/

Play time—song title—artist name—album title —number of songs

Scrolling the text information to the left 1 Press and hold DISP/

Note

Incompatible text saved on the iPod will not be displayed by the unit.

Browsing for a song

1 Press to switch to the top menu of the list search.

/SCRL.

Section

English

Section

Operating this unit

2 Use M.C. to select a category/song.

Changing the name of song or category

1 Tur n M.C.

PLAYLISTS (playlists)—ARTISTS (artists)—ALBUMS (albums)—SONGS (songs)—PODCASTS

(podcasts)—GENRES (genres)—COMPOSERS (composers)—AUDIOBOOKS (audiobooks)

Playing 1 When a song is selected, press M.C.

Seeing a list of songs in the selected category 1 When a category is selected, press M.C.

Playing a song in the selected category 1 When a category is selected, press and hold M.C.

Searching by alphabet in the list 1 When a list for the selected category is displayed,

press

2 Tur n M.C. to select a letter. 3 Press M.C. to display the alphabetical list.

If alphabet search is aborted, NOT FOUND is displayed.

to switch to alphabet search mode.

Note

Depending on the number of files in the iPod, there may be a delay when displaying a list.

Advanced operations using special buttons

Selecting a repeat play range 1 Press 6/

! ONE – Repeat the current song ! ALL – Repeat all songs in the selected list

Playing all songs in a random order (shuffle all) 1 Press 5/

Pausing playback Refer to Pausing playback on the previous page.

to cycle between the following:

to turn shuffle all on.

Playing songs related to the currently playing song You can play songs from the following lists.

! Album list of currently playing artist ! Song list of currently playing album ! Album list of currently playing genre

1 Press and hold M.C. to switch to the link play

mode.

2 Tur n M.C. to change the mode; press to select.

! ARTIST – Plays an album of currently playing

artist.

! ALBUM – Plays a song of currently playing

album.

! GENRE – Plays an album of currently playing

genre. The selected song/album will be played after the currently playing song.

The selected song/album may be cancelled if you operate functions other than link search (e.g. fast forward and reverse). If no related albums/songs are found, NOT FOUND is displayed. Depending on the song selected to play, the end of the currently playing song and the beginning of the selected song/album may be cut off.

Operating this unit’s iPod function from your iPod This function is not compatible with the following iPod models.

! iPod nano 1st generation ! iPod 5th generation

This unit’s iPod function allows you to conduct operations from your iPod and listen to it using your car ’s speakers. 1 Press 4/IPOD to switch the control mode.

! IPOD – This unit’s iPod function can be oper-

ated from the connected iPod. ! AUDIO – This unit’s iPod function can be op-

erated from this unit.

Enhancing compressed audio and restoring rich sound (sound retriever) Refer to Enhancing compressed audio and r estoring rich sound (sound retriever) on the previous page.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select FUNCTION.

3 Turn M.C. to select the function.

After selecting, perform the following procedures to set the function.

Operating this unit

REPEAT (repeat play)

! Refer to REPEAT (repeat play) on page 9.

However the repeat range is different from CD/ USB storage device. Refer to Selecting a repeat play range on the previous page.

SHUFFLE (shuffle)

1 Press M.C. to display the setting mode. 2 Tur n M.C. to select your favorite setting.

! SONGS – Play back songs in the selected list

in random order.

! ALBUMS – Play back songs from a randomly

selected album in order.

! OFF – Cancel random play.

3 Press M.C. to confirm the selection.

SHUFFLE ALL (shuffle all)

1 Press M.C. to turn shuffle all on.

To turn off, set SHUFFLE in the FUNCTION menu to off.

LINK PLAY (link play)

1 Press M.C. to display the setting mode. 2 Tur n M.C. to change the mode; press to select.

For details about the settings, refer to Playing songs related to the currently playing song on the

previous page.

CTRL (control mode)

1 Press M.C. to select your favorite setting.

For details about the settings, refer to Operating this unit’s iPod function from your iPod on the previous page.

PAUSE (pause)

! Refer to PAUSE (pause) on page 9.

AUDIO BOOK (audiobook speed)

The playback speed of audiobook can be changed.

1 Press M.C. to display the setting mode. 2 Tur n M.C. to select your favorite setting.

! FASTER – Playback faster than normal speed ! NORMAL – Playback in normal speed ! SLOWER – Playback slower than normal

speed

3 Press M.C. to confirm the selection.

S.RTRV (sound retriever)

Section

English

Notes

! Operation is complete even if the menu is can-

celled before being confirmed.

! Switching the control mode to IPOD pauses

song playback. Operate the iPod to resume playback.

! The following functions are still accessible

from the unit even if the control mode is set to IPOD.

— Volume — Fast forward/reverse — Track up/down — Pausing — Switching the text information

! When the control mode is set to IPOD, opera-

tions are limited as follows: — Only CTRL (control mode), PAUSE (pause)

and S.RTRV (sound retriever) functions are available.

— Browse function cannot be operated from

this unit.

Audio Adjustments

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option and press to select AUDIO.

3 Turn M.C. to select the audio function.

After selecting, perform the following procedures to set the audio function.

FAD/BAL (fader/balance adjustment)

You can change the fader/balance setting.

1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between fader and balance. 3 Tur n M.C. to adjust speaker balance.

Adjustment range (front/rear): F15 to R15 Adjustment range (left/right): L15 to R15 FR 0 is the proper setting when only two speakers are used.

EQUALIZER (equalizer recall)

! Refer to S.RTRV (sound retriever) on page 9.

Section

Operating this unit

There are six stored settings DYNAMIC (dynamic), VOCAL (vocal), NATURAL (natural), CUSTOM (cus- tom), FLAT (flat) and POWERFUL (powerful).

! When FLAT is selected no adjustments are made

to the sound.

1 Press M.C. to display the setting mode. 2 Tur n M.C. to select the equalizer.

DYNAMIC—VOCAL—NATURAL—CUSTOM— FLAT—POWERFUL

3 Press M.C. to confirm the selection.

TONE CTRL (equalizer adjustment)

You can adjust the bass/mid/treble level. ! Adjusted equalizer curve settings are stored in

CUSTOM.

1 Press M.C. to display the setting mode. 2 Press M.C. to select BASS (bass)/MID (mid)/TRE-

BLE (treble).

3 Tur n M.C. to adjust the level.

Adjustment range: +6 to -6

LOUDNESS (loudness)

Loudness compensates for deficiencies in the lowand high-frequency ranges at low volume.

1 Press M.C. to display the setting mode. 2 Tur n M.C. to select the desired setting.

OFF (off)—LOW(low)—HIGH (high)

3 Press M.C. to confirm the selection.

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the vo-

lume level of each source to prevent radical changes in volume when switching between sources. ! Settings are based on the FM volume level, which

remains unchanged. Before adjusting source levels, compare the FM volume level with the level of the source you wish to adjust.

! The AM volume level can also be adjusted with

source level adjustments.

1 Press M.C. to display the setting mode. 2 Tur n M.C. to adjust the source volume.

Adjustment range: +4 to –4

3 Press M.C. to confirm the selection.

Notes

! When selecting FM as the source, you cannot

switch to SLA.

! Operation is complete even if the menu is can-

celled before being confirmed.

Initial Settings

1 Press SRC/OFF and hold until the unit turns off.

2 Press M.C. and hold until CLOCK SET appears in the display.

3 Turn M.C. to select the initial setting.

After selecting, perform the following procedures to set the initial setting.

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode. 2 Press M.C. to select the segment of the clock dis-

play you wish to set. Hour—Minute As you select segments of the clock display, the selected segment flashes.

3 Tur n M.C. to adjust the clock.

AUX (auxiliary input)

Activate this setting when using auxiliary device connected to this unit.

1 Press M.C. to turn AUX on or off.

USB (plug and play)

This setting allows you to switch your source to USB / IPOD automatically. 1 Press M.C. to turn the plug and play on or off.

ON – When USB storage device/iPod is con-

nected, the source is automatical ly switched to USB/IPOD. If you disconnect your USB storage device/iPod, this unit’s source is turned off. OFF – When USB storage device/iPod is con- nected, the source is not switched to USB/IPOD automatically. Please change the source to USB/

IPOD manually.

ILLUMI (illumination color)

You can select the desired illumination color.

1 Press M.C. to display the setting mode. 2 Tur n M.C. to select the desired setting.

RED (red)—GREEN (green)

3 Press M.C. to confirm the selection.

Note

Operation is complete even if the menu is cancelled before being confirmed.

Operating this unit

Using the AUX source

1 Insert the stereo mini plug into the AUX input jack.

2 Press SRC/OFF to select AUX as the source.

Note

AUX cannot be selected unless the auxiliary setting is turned on. For more details, refer to AUX (auxiliary input) on the previous page.

Turning the clock display on or off

% Press CLOCK to turn the clock display on or off.

Note

The clock display disappears temporarily when you perform other operations, but the clock display appears again after 25 seconds.

Section

English

Section

Connections

WARNING

! Use speakers over 50 W (output value) and be-

tween 4 W to 8 W (impedance value). Do not use 1 W to 3 W speakers for this unit.

! The black cable is ground. When installing

this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly connected to metal parts of the car’s body. The ground wire of the power amp and the one of this unit or any other device must be connected to the car separately with different screws. If the screw for the ground wire loosens or falls out, it could result in fire, generation of smoke or malfunction.

Ground wire

Other devices (Another electronic device in the car)

Metal parts of car’s body

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.

POWER AMP

— Secure the wiring with cable clamps or ad-

hesive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring.

— Place all cables away from moving parts,

such as the gear shift and seat rails.

— Place all cables away from hot places,

such as near the heater outlet.

— Do not connect the yellow cable to the bat-

tery by passing it through the hole to the engine compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables. — Never cut the insulation of the power cable

of this unit in order to share the power with other devices. The current capacity of the cable is limited.

— Use a fuse of the rating prescribed. — Never wire the negative speaker cable di-

rectly to ground.

— Never band together negative cables of

multiple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this cable to the system remote control of an external power amp or the vehicle’s auto-antenna relay control terminal (max. 300 mA 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction.

ACC position No ACC position

! Use this unit with a 12-volt battery and nega-

tive grounding only. Failure to do so may result in a fire or malfunction.

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions below. — Disconnect the negative terminal of the

battery before installation.

Connections

Connection diagram

This product

Antenna jack

Section

English

Power amp (sold separately)

Connect with RCA cables (sold separately)

Fuse (10 A)

Yellow Connect to the constant 12 V supply terminal.

Red Connect to terminal controlled by ignition switch (12 V DC).

Black (chassis ground) Connect to a clean, paint-free metal location.

Front speaker Front speaker

Left Right

Rear speaker Rear speaker









Rear output

White

White/black

Green

Green/black

System remote control

Blue/white Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.

Gray

Gray/black

Violet

Violet/black









Rear speaker Rear speaker





Perform these connections when using the optional amplifier.





Section

Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires dril-

ling of holes or other modifications to the vehicle.

! Do not install this unit where :

— it may interfere with operation of the vehi-

cle.

— it may cause injury to a passenger as a re-

sult of a sudden stop.

! The semiconductor laser will be damaged if it

overheats. Install this unit away from hot places such as near the heater outlet.

! Optimum per formance is obtained when the

unit is installed at an angle of less than 60°.

60°

DIN front/rear mount

This unit can be properly installed either from

“Front” (conventional DIN front-mount) or “Rear” (DIN rear-mount installation, utilizing

threaded screw holes on the sides of unit chassis). For details, refer to the following installation methods.

DIN Front-mount

1 Insert the mounting sleeve into the dashboard.

For installation in shallow spaces, use the supplied mounting sleeve. If there is enough space, use the mounting sleeve that came with the vehicle.

2 Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.

Dashboard

Mounting sleeve

3 Install the unit as illustrated.

Use commercially available parts when installing.

Nut

Firewall or metal support

Screw

Screw (M48)

# Make sure that the unit is installed securely in place. An unstable installation may cause skipping or other malfunctions.

Metal strap

DIN Rear-mount

1 Determine the appropriate position where the holes on the bracket and the side of the unit match.

Installation

Section

2 Tighten two screws on each side.

Screw

Mounting bracket Dashboard or console

! Use either truss (5 mm × 8 mm) or flush

surface (5 mm × 9 mm) screws, depending on the bracket screw holes.

Removing the unit

1 Extend top and bottom of the trim ring outwards to remove the trim ring. (When reattaching the trim ring, point the side with the groove down.)

Trim ring

! Releasing the front panel allows easier ac-

cess to the trim ring.

English

Fastening the front panel

If you do not plan to detach the front panel, the front panel can be fastened with the supplied screw.

Screw

2 Insert the supplied extraction keys into both sides of the unit until they click into place.

3 Pull the unit out of the dashboard.

Appendix

Additional Information

Troubleshooting

Symptom Cause Action

The display automatically returns to the ordinary display.

The repeat play range changes unexpectedly.

A subfolder is not played back.

NO XXXX appears when a display is changed (e.g., NO TITLE).

The display is illuminated when the unit is turned off.

The unit is malfunctioning. There is interference.

You did not perform any operation within about 30 seconds.

Depending on the repeat play range, the selected range may change when selecting another folder or track, or when fast forwarding/reversing.

Subfolders cannot be played when FOLDER (folder repeat) is selected.

No text information embedded

Demo mode is on.

You are using a device, such as a cell phone, that transmits electromagnetic waves near the unit.

Perform operation again.

Select the repeat play range again.

Select another repeat play range.

Switch the display or play another track/file.

Press DISP/ SCRL to cancel demo mode.

Move electrical devices that may be causing the interference away from the unit.

Error messages

When you contact your dealer or your nearest Pioneer Service Center, be sure to note the error message.

Built-in CD Player

Message Cause Action

ERROR-11, 12, 17, 30

ERROR-10, 11, 12, 15, 17, 30, A0

ERROR-15 The inserted disc

ERROR-22, 23 Unsupported CD

FRMT READ There is some-

NO AUDIO The inserted disc

SKIPPED The inserted disc

PROTECT All the files on

Dirty disc Clean disc. Scratched disc Replace disc. Electrical or me-

chanical

is blank

format

times a delay between the start of playback and when you start to hear any sound

does not contain any playable files

contains DRM protected WMA files

the inserted disc are embedded with DRM

Turn the ignition switch OFF and back ON, or switch to a different source, then back to the CD player.

Replace disc.

Wait until the message disappears and you hear sound.

Replace disc.

USB storage device

Message Cause Action

NO DEVICE When plug and

play is off, no USB storage device is connected.

FRMT READ There is some-

times a delay between the start of playback and when you start to hear any sound

! Turn the plug and play on. ! Connect a compatible USB storage device.

Wait until the message disappears and you hear sound.

Additional Information

NO AUDIO

No songs Transfer the audio

The connected USB storage device has security enabled

SKIPPED The connected

USB storage device contains WMA files embedded with Windows Mediaä DRM 9/10

PROTECT All the files in the

USB storage device are embedded with Windows Media DRM 9/10

N/A USB The USB storage

device connected to is not supported by this unit.

CHECK USB The USB connec-

tor or USB cable has shortcircuited.

The connected USB storage device consumes more than 500 mA (maximum allowable current).

ERROR-18 Not compatible

USB device

files to the USB storage device and connect.

Follow the USB storage device instructions to disable the security.

Play an audio file not embedded with Windows Media DRM 9/10.

Transfer audio files not embedded with Windows Media DRM 9/10 to the USB storage device and connect.

Connect a USB Mass Storage Class compliant device.

Check that the USB connector or USB cable is not caught in something or damaged.

Disconnect the USB storage device and do not use it. Turn the ignition switch to OFF, then to ACC or ON and then connect only compliant USB storage devices.

Disconnect your device and replace it with a compatible USB storage device.

Communication

ERROR-19

ERROR-23 USB storage de-

failure

vice is not formatted with FAT16 or FAT32

Perform one of the following operations. –Turn the ignition switch OFF and back ON. –Disconnect or eject the USB storage device. –Change to a different source. Then, return to the USB source.

USB storage device should be formatted with FAT16 or FAT32.

iPod

Message Cause Action

NO DEVICE When plug and

play is off, no USB storage device or iPod is connected.

FRMT READ There is some-

times a delay between the start of playback and when you start to hear any sound

ERROR-19 Communication

failure

iPod failure Disconnect the

ERROR-16, 18 Old iPod firm-

ware versions iPod failure Disconnect the

! Turn the plug and play on. ! Connect a compatible iPod.

Wait until the message disappears and you hear sound.

Disconnect the cable from iPod. Once iPod’s main menu is displayed, reconnect cable. Reset the iPod.

cable from iPod. Once iPod’s main menu is displayed, reconnect cable. Reset the iPod.

Update the iPod version.

cable from iPod. Once iPod’s main menu is displayed, reconnect cable. Reset the iPod.

Appendix

English

Appendix

Additional Information

iPod operates

CHECK USB

NO SONGS No songs Transfer songs to

STOP No songs in the

correctly but does not charge

current list

Check if the connection cable for iPod shorted out (e.g., not caught in metal objects). After checking, turn the ignition switch OFF and back ON or disconnect the iPod and reconnect.

iPod. Select a list that

contains songs.

Handling guideline

Discs and player

Use only discs featuring either of following two logos.

Use 12-cm disc. Do not use 8-cm disc or an adapter for 8-cm disc.

Use only conventional, fully circular discs. Do not use shaped discs.

Do not insert anything other than a CD into the CD loading slot.

Do not use cracked, chipped, warped, or otherwise damaged discs as they may damage the player.

Unfinalized CD-R/CD-RW disc playback is not possible.

Do not touch the recorded surface of the discs.

Store discs in their cases when not in use.

Avoid leaving discs in excessively hot environments including under direct sunlight.

Do not attach labels, write on or apply chemicals to the surface of the discs.

To clean a CD, wipe the disc with a soft cloth outward from the center.

Condensation may temporarily impair the player’s performance. Leave it to adjust to the warmer temperature for about one hour. Also, wipe any damp discs with a soft cloth.

Playback of discs may not be possible because of disc characteristics, disc format, recorded application, playback environment, storage conditions, and so on.

Road shocks may interrupt disc playback.

Read the precautions for discs before using them.

USB storage device

Address any questions you have about your USB storage device to the manufacturer of the device.

Connections via a USB hub are not supported.

Do not connect anything other than a USB storage device.

Do not leave the USB storage device in any place with high temperatures.

Firmly secure the USB storage device when driving. Do not let the USB storage device fall onto the floor, where it may become jammed under the brake or accelerator pedal.

Depending on the USB storage device, the following problems may occur.

! Operations may vary. ! This unit may not recognize the storage device. ! The file may not be played back properly. ! The device may generate noise in the radio.

iPod

Do not leave the iPod in direct sunlight for extended amounts of time. Extended exposure to direct sunlight can result in iPod malfunction due to the resulting high temperature.

Do not leave the iPod in any place with high temperatures.

To ensure proper operation, connect the dock connector cable from the iPod directly to this unit.

Additional Information

Firmly secure the iPod when driving. Do not let the iPod fall onto the floor, where it may become jammed under the brake or accelerator pedal.

For details, refer to the iPod’s manuals.

About iPod settings ! You cannot operate the iPod Equalizer on Pioneer

products. We recommend that you set the iPod Equalizer to off, before connecting to this unit.

! You cannot set Repeat to off on the iPod when

using this unit. Repeat is automatically changed to All when connecting the iPod to this unit.

DualDiscs

DualDiscs are two-sided discs that have a recordable CD for audio on one side and a recordable DVD for video on the other. Since the CD side of DualDiscs is not physically compatible with the general CD standard, it may not be possible to play the CD side with this unit. Frequent loading and ejecting of a DualDisc may result in scratches on the disc. Serious scratches can lead to playback problems on this unit. In some cases, a DualDisc may become stuck in the disc loading slot and will not eject. To prevent this, we recommend you refrain from using DualDisc with this unit. Please refer to the information from the disc manufacturer for more detailed information about DualDiscs.

Compressed audio compatibility (disc, USB)

WMA

File extension: .wma

Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to 384 kbps (VBR)

Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

Windows Media Audio Professional, Lossless, Voice/ DRM Stream/Stream with video: No

MP3

File extension: .mp3

Bit rate: 8 kbps to 320 kbps

Appendix

English

Sampling frequency: 16 kHz to 48 kHz (32, 44.1, 48 kHz for emphasis)

Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3 tag Version 2.x is given priority over Version 1.x.)

M3u playlist: No

MP3i (MP3 interactive), mp3 PRO: No

WAV

File extension: .wav

Quantization bits: 8 and 16 (LPCM), 4 (MS ADPCM)

Sampling frequency: 16 kHz to 48 kHz (LPCM), 22.05 kHz and 44.1 kHz (MS ADPCM)

Supplemental information

Only the first 32 characters can be displayed as a file name (including the file extension) or a folder name.

This unit may not operate correctly depending on the application used to encode WMA files.

There may be a slight delay when starting playback of audio files embedded with image data.

Disc

Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers.)

Playable folders: up to 99

Playable files: up to 999

File system: ISO 9660 Level 1 and 2, Romeo, Joliet

Multi-session playback: Yes

Packet write data transfer: No

Regardless of the length of blank section between the songs of the original recording, compressed audio discs play with a short pause between songs.

USB storage device

Playable folder hierarchy: up to eight tiers (A practical hierarchy is less than two tiers.)

Playable folders: up to 500

Playable files: up to 15 000

Playback of copyright protected files: No

Appendix

Additional Information

Partitioned USB storage device: Only the first partition can be played.

There may be a slight delay when starting playback of audio files on a USB storage device with numerous folder hierarchies.

CAUTION

Pioneer accepts no responsibility for data lost on the USB storage device even if that data is lost while using this unit.

iPod compatibility

This unit supports only the following iPod models. Supported iPod software versions are shown below. Older versions may not be supported.

! iPod nano 4th generation (software version 1.0.3) ! iPod nano 3rd generation (software version 1.1.3) ! iPod nano 2nd generation (software version 1.1.3) ! iPod nano 1st generation (software version 1.3.1) ! iPod touch 2nd generation (software version 2.2.1) ! iPod touch 1st generation (software version 2.2.1) ! iPod classic 120GB (software version 2.0.1) ! iPod classic (software version 1.1.2) ! iPod 5th generation (software version 1.3) ! iPhone 3G (software version 2.2.1) ! iPhone (software version 2.2.1)

Depending on the generation or version of the iPod, some functions can not be operated.

Operations may vary depending on the software version of iPod.

When using an iPod, iPod Dock Connector to USB Cable is required.

Pioneer CD-IU50 interface cable is also availabl e. For details, consult your dealer.

Compatible file: MP3 (.mp3)/WAV (.wav)/AAC (.m4a)

Compatible format: AAC (16 Kbps to 320 Kbps), AAC VBR, Protected AAC (Purchased from iTunes Music Store)/MP3 (16 Kbps to 320 Kbps), MP3 VBR/Audible (Format 2, 3, 4), Apple Loss less, AIFF, WAV

Audio Book, Podcast: Yes

CAUTION

Pioneer accepts no responsibility for data lost on the iPod even if that data is lost while using this unit.

Sequence of audio files

The user cannot assign folder numbers and specify playback sequences with this unit.

Example of a hierarchy

 

Level 1 Level 2 Level 3 Level 4



  

Disc

Folder selection sequence or other operation may differ depending on the encoding or writing software.

USB storage device

Playback sequence is the same as recorded sequence in the USB storage device. To specify the playback sequence, the following method is recommended.

1 Create the file name including numbers that

specify the playback sequence (e.g., 001xxx.mp3 and 099yyy.mp3).

2 Put those files into a folder. 3 Save the folder containing files on the USB

storage device.

However, depending on the system environment, you cannot specify the playback sequence. For USB portable audio players, the sequence is different and depends on the player.

: Folder

: Compressed audio file 01 to 05: Folder number 1 to 6: Playback sequence

Additional Information

Appendix

iTunes

Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.

MP3

Supply of this product only conveys a license for private, non-commercial use and does not convey a license nor imply any right to use this product in any commercial (i.e. revenuegenerating) real time broadcasting (terrestrial, satellite, cable and/or any other media), broadcasting/streaming via internet, intranets and/ or other networks or in other electronic content distribution systems, such as pay-audio or audio-on-demand applications. An independent license for such use is required. For details, please visit http://www.mp3licensing.com.

WMA

iPod

English

iPod is a trademark of Apple Inc., registered in the U.S. and other countries. “Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

iPhone

Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc.

iPhone is a trademark of Apple Inc. “Works with iPhone” means that an electronic accessory has been designed to connect specifically to iPhone and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

Specifications

General

Power source ............................. 14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system ................... Negative type

Maximum current consumption

..................................................... 10.0 A

+ 52 hidden pages