Connecting the unitsConnecting the unitsConnecting the units
DVD RDS AV RECEIVER
DVD RDS AV РЕСИВЕР
AVH-P4200DVD
AVH-P3200BT
Installation Manual
Руководствопоустановке
Printed in Thailand
ОтпечатановТаиланде
<CRD4451-A/N> UW
<KOMNX> <09L00000>
WARNING
• To avoid the risk of accident and the potential
violation of applicable laws, the front DVD or TV
(sold separately) feature should never be used
while the vehicle is being driven. Also, rear displays
should not be in a location where it is a visible
distraction to the driver.
• In some countries or states the viewing of images
on a display inside a vehicle even by persons
other than the driver may be illegal. Where such
regulations apply, they must be obeyed and this
unit’s DVD features should not be used.
CAUTION
• PIONEER does not recommend that you install
or service your display yourself. Installing or
servicing the product may expose you to risk
of electric shock or other hazards. Refer all
installation and servicing of your display to
authorized Pioneer service personnel.
• Secure all wiring with cable clamps or
electrical tape. Do not allow any bare wiring to
remain exposed.
• Do not drill a hole into the engine compartment
to connect the yellow lead of the unit to
the vehicle battery. Engine vibration may
eventually cause the insulation to fail at
the point where the wire passes from the
passenger compartment into the engine
compartment. Take extra care in securing the
wire at this point.
• It is extremely dangerous to allow the display
lead to become wound around the steering
column or gearshift. Be sure to install the
display in such a way that it will not obstruct
driving.
• Make sure that wires will not interfere with
moving parts of the vehicle, such as the
gearshift, parking brake or seat sliding
mechanism.
• Do not shorten any leads. If you do, the
protection circuit may fail to work properly.
WARNING
LIGHT GREEN LEAD AT POWER CONNECTOR
IS DESIGNED TO DETECT PARKED STATUS
AND MUST BE CONNECTED TO THE POWER
SUPPLY SIDE OF THE PARKING BRAKE SWITCH.
IMPROPER CONNECTION OR USE OF THIS LEAD
MAY VIOLATE APPLICABLE LAW AND MAY RESULT
IN SERIOUS INJURY OR DAMAGE.
Important
• This unit cannot be installed in a vehicle without
ACC (accessory) position on the ignition switch.
C
C
A
O
F
N
F
O
ACC position
• Use of this unit in conditions other than the
following could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm to
8 ohm (impedance value).
• To prevent short-circuit, overheating or malfunction,
be sure to follow the directions below.
— Disconnect the negative terminal of the battery
before installation.
— Secure the wiring with cable clamps or adhesive
tape. Wrap adhesive tape around wiring that
comes into contact with metal parts to protect
the wiring.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not connect the yellow cable to the battery
by passing it through the hole to the engine
compartment.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power with other
devices. The current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly to
ground.
— Never band together negative cables of multiple
speakers.
S
T
A
R
T
No ACC position
O
F
N
F
O
S
T
A
R
T
• When this unit is on, control signals are sent
through the blue/white cable. Connect this cable to
the system remote control of an external power amp
or the vehicle’s auto-antenna relay control terminal
(max. 300 mA 12 V DC). If the vehicle is equipped
with a glass antenna, connect it to the antenna
booster power supply terminal.
• Never connect the blue/white cable to the power
terminal of an external power amp. Also, never
connect it to the power terminal of the auto
antenna. Doing so may result in battery drain or a
malfunction.
• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
• The black cable is ground. Ground cables for
this unit and other equipment (especially, highcurrent products such as power amps) must be
wired separately. If they are not, an accidental
detachment may result in a fire or malfunction.
When connecting to separately sold power amp
Rear output
Front output
To rear output
To front output
Subwoofer output
This product
Blue/white
Connect to system control
terminal of the power amp
(max. 300 mA 12 V DC).
Blue/white (5*)
The pin position of the ISO connector will differ
depending on the type of vehicle. Connect 5*
and 6* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 5* and 6*.
•When you connect the separately sold
multi-channel processor (DEQ-P6600) to this
unit, do not connect anything to the speaker
leads and system remote control (blue/white).
•When you connect the multi-channel
processor to this unit, refer to multi-channel
processor’s installation manual for the
connection method.
Perform these connections when
using the optional amplifier.
(AVHP4200DVD
only)
To subwoofer
output
Blue/white (6*)
Connect to auto-antenna
relay control terminal
(max. 300 mA 12 V DC).
Subwoofer
Front speakerFront speaker
Rear speaker
Connect with RCA cables
(sold separately)
System remote control
LeftRight
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Subwoofer
Rear speaker
Connecting the unitsConnecting the unitsConnecting the unitsConnecting the units
Connecting the power cord
Navigation unit can
be connected
(AVIC-F220 (sold
separately)).
Please contact your dealer to
inquire about the
connectable navigation unit.
Note:
Depending on the kind of vehicle,
the function of 2* and 4* may be
different. In this case, be sure to
connect 1* to 4* and 3* to 2*.
2*
4*
ellow (2*)
Y
Back-up
(or accessory)
Red (4*)
Accessory
(or back-up)
Orange/white
Connect to lighting switch terminal.
Black (chassis ground)
Connect to a clean, paint-free metal location.
ISO connector
Note:
In some vehicles, the ISO connector may be divided into
. In this case, be sure to connect to both connectors.
two
When you connect the separately sold
multi-channel processor (DEQ-P6600) to this
unit, do not connect anything to the speaker
leads and system remote control (blue/white).
26 pin cable (Supplied with Navigation unit)
Insert the 26 pin cable in the
direction indicated in the figure.
1*
3*
ellow (1*)
Y
Connect to the constant 12 V
supply terminal.
Red (3*)
Connect to terminal controlled by
ignition switch (12 V DC).
AUX jack (3.5 ø) (AVH-P4200DVD)
Use a mini plug cable to connect with auxiliary device.
Microphone input (AVH-P3200BT)
RGB input
This product
Fuse (10 A)
Antenna input
Connect leads of the same
color to each other.
Fuse resistor
Fuse resistor
Speaker leads
White: F
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left or subwoofer
Green/black: Rear left or subwoofer
Violet: Rear right or subwoofer
Violet/black: Rear right or subwoofer
ront lef
t
(AVHP4200DVD
only)
4 m
Wired remote
input
Hard-wired
remote control
adaptor can be
connected (sold
separately).
Microphone
(AVH-P3200BT only)
Fuse resistor
Connection method
1. Clamp
Note:
· The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner’s Manual or dealer.
Light green
Used to detect the ON/OFF status of the parking brake. This lead
must be connected to the power supply side of the parking brake
switch.
Blue/white
Connect to system control terminal of the power
amp (max. 300 mA 12 V DC).
Blue/white (6*)
Blue/white (5*)
The pin position of the ISO
connector will differ depending on
the type of vehicle. Connect 5* and
6* when P
type. In another type of vehicle,
never connect 5* and 6*.
in 5 is an antenna control
Connect to auto
(max. 300 mA 12 V DC).
Violet/white
Of the two lead wires connected to the back lamp, connect the one
in which the voltage changes when the gear shift is in the
REVERSE (R) position. This connection enables the unit to
sense whether the car is moving forwards or backwards.
Yellow/black
If you use an equipment with Mute function
the Audio Mute lead on that equipment. If not, keep the Audio
Mute lead free of any connections.
the lead.
-antenna relay control terminal
Notes:
· Change the initial setting of this unit (refer to the Operation Manual). The
subwoofer output of this unit is monaural.
· When using a subwoofer of 70 W (2 Ω) , be sure to connect with V
Violet/black leads of this unit. Do not connect anything to Green and
Green/black leads.
ower supply side
P
Ground side
, wire this lead to
2. Clamp
firmly with
needle-nosed pliers.
Parking brake
switch
iolet and
Connecting the system (AVH-P4200DVD only)
Microphone
for hands-free phoning
(supplied with Bluetooth adapter)
IP-BUS input
This product
Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
1.5 m
Bluetooth adapter
(e.g. CD-BTB200)
(sold separately)
Black
IP-BUS cable
(Supplied with Bluetooth adapter)
When connecting with supplied USB cable (AVH-P4200DVD
only)
Microphone
for hands-free phoning
(supplied with Bluetooth adapter)
IP-BUS input
This product
1.5 m
Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
1.5 m
USB cable
(supplied with this unit)
Connect to sparately sold
USB device.
Bluetooth adapter
(e.g. CD-BTB200)
(sold separately)
Black
IP-BUS cable
(Supplied with Bluetooth adapter)
When connecting with optional CD-IU200V cable (AVHP4200DVD only)
Microphone
for hands-free phoning
(supplied with Bluetooth adapter)
Dock connector
Interface cable
(CD-IU200V) (sold separately)
1.5 m
IP-BUS cable
(Supplied with Bluetooth adapter)
Bluetooth adapter
(e.g. CD-BTB200)
(sold separately)
AUX input (AUX)
This product
IP-BUS input
1.5 m
Wired remote input
Hard-wired remote control adaptor
can be connected (sold separately).
iPod with video capabilities
(sold separately)
USB input
USB cable
Black
Connecting the unitsConnecting the unitsConnecting the unitsConnecting the units
When connecting with a rear view camera
When this product is used with a rear view camera, it is possible to automatically switch from
the video to rear view image when the gear shift is moved to REVERSE (R).
WARNING
USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY
RESULT IN INJURY OR DAMAGE.
CAUTION
• The screen image may appear reversed.
• The rear view camera function is to be used as an aid for backing into a tight parking spot. Do
not use this function for entertainment purposes.
• Objects in the rear view may appear closer or more distant than they actually are.
CAUTION
Rear view camera input (R.C IN)
To video output
RCA cable (sold separately)
This product
• It is necessary to set Camera Polarity properly in System when connecting the rear view camera.
(AVH-P4200DVD only)
Fuse resistor
Violet/white
Of the two lead wires connected to the back lamp, connect the one
in which the voltage changes when the gear shift is in the
REVERSE (R) position. This connection enables the unit to
sense whether the car is moving forwards or backwards.
You must use a camera
which outputs mirror
reversed images.
Rear view camera
(sold separately)
When connecting with a multi-channel processor
Microphone
for hands-free phoning
(supplied with Bluetooth adapter)
This product
To SWR
IP-BUS cable (supplied with
multi-channel processor)
IP-BUS input
To SWL
Optical
output
Black
RCA cable (supplied with
multi-channel processor)
Wired remote input
Hard-wired remote
control adaptor
can be connected
(sold separately).
(A
VH-P4200DVD only)
Optical cable connection box
(supplied with multi-channel processor)
Optical cable
(supplied with
multi-channel processor)
Blue
Blue
Bluetooth adapter
(e.g. CD-BTB200)
(sold separately)
(AVH-P4200DVD only)
Black
Connecting and installing the optical cable connection box
WARNING
• Avoid installing the optical cable connection
box in locations where the operation of safety
devices such as airbags is prevented by this
unit. Otherwise, there is a danger of a fatal
accident.
• Avoid installing the optical cable connection
box in locations where the operation of the
brake may be prevented. Otherwise, it may
result in a traffic accident.
• Fix the optical cable connection box securely
with the hook and loop fastener or lock tie. If
the unit is loose, it disturbs driving stability,
which may result in a traffic accident.
CAUTION
• Install this unit using only the parts supplied with
this unit. If other parts are used, this unit may be
damaged or could dismount itself, which leads to
an accident or other problems.
• Do not install this unit near the doors where
rainwater is likely to be spilled on the unit. Incursion
of water into the unit may cause smoke or fire.
Connecting the optical cable
1. Connect the optical cable and ground
lead to the main unit.
Connect the optical cable so that it does not
protrude from the main unit, as shown in the
illustration. Fasten the ground lead to the
protrusion on the back of the main unit.
Screw
2. Connect the optical cable to the optical
cable connection box.
optical cable
Installing the optical cable
connection box
• When installing the optical cable
connection box with the hook and loop
fastener.
Install the optical cable connection box
using the hook and loop fastener in the
ample space of the console box.
Hook fastener
Loop fastener
• When installing the optical cable
connection box with the lock tie.
Wrap the optical cable and connection box with
the protection tape and fasten with the power
code using the lock tie.
Wrap with the protection tape
When connecting the external video component and the display
Display with RCA
input jacks (sold
separately)
To video input
To audio input
Rear monitor output (V OUT)
Video input (V IN)
Rear audio output
(REAR AUDIO OUT)
This product
• It is necessary to change AV Input in System when connecting the external video component.
Audio input
(L IN, R IN)
(AVH-P4200DVD only)
To audio outputs
RCA cables
(sold separately)
Mini pin plug cable
(sold separately)
To video output
External video
component (sold
separately)
Fasten with the lock tie
When using a display connected to rear video output
This product’s rear video output and rear audio output are for connection of a display to
enable passengers in the rear seats to watch the DVD, etc.
WARNING
Never install the display in a location where it is visible to the driver while driving.
Loading...
+ 5 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.