Pilz PSSu E AI SHT1 User Manual

Operating Manual PSSu E AI SHT1(-T)

Operating Manual PSSu E AI SHT1(-T)

PSSu E AI SHT1(-T)

Decentralised system PSSuniversal I/O

Operating Manual — No. 1001465-EN-03

This document is a translation of the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for internal purposes.

Suggestions and comments for improving this documentation will be gratefully received.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®, SafetyEYE®,
SafetyNET p®, the spirit of safety® are registered and protected trademarks of
Pilz GmbH & Co. KG in some countries.

SD means Secure Digital.

Preface

Contents

Contents

Contents Page

Chapter 1 Introduction

1.1 Validity of documentation 1-1

1.1.1 Retaining the documentation 1-1

1.1.2 Terminology: System environment A and B 1-1

1.2 Overview of documentation 1-2

1.3 Definition of symbols 1-3

Chapter 2 Overview

2.1 Module structure 2-1

2.1.1 Module features 2-1

2.2 Front view 2-2

Chapter 3 Safety

3.1 Intended use 3-1

3.2 Safety regulations 3-2

3.2.1 Use of qualified personnel 3-2

3.2.2 Warranty and liability 3-2

3.2.3 Disposal 3-2

Chapter 4 Function Description

4.1 Module features 4-1

4.1.1 Function description 4-1

Chapter 5 Installation

5.1 General installation guidelines 5-1

5.1.1 Dimensions 5-1

5.2 Installing the base module 5-3

5.3 Inserting and removing an electronic
module

5.3.1 Inserting an electronic module 5-4

5.3.2 Removing an electronic module 5-5

5.3.3 Changing an electronic module during
operation

5-4

5-5

Chapter 6 Wiring

6.1 General wiring guidelines 6-1

6.1.1 Mechanical connection of the base
modules

6.2 Terminal configuration 6-4

6.3 Connecting the module 6-6

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

6-1

1

Contents

Chapter 7 Technical Details

7.1 Technical details 7-1

7.2 Order reference 7-3

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany

2

Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

1 Introduction

1.1 Validity of documentation

11000IntroductionIntroduction1-1.1Validity of docume ntation1100Validity of documenta tion1-][BA Einf Gültigkeit_(T)

This documentation is valid for the product types PSSu E AI SHT1 and

Einf Einleitung

1.1.1 Retaining the documentation

Retaining the documentation1-Einf Aufbewahren

PSSu E AI SHT1-T. It is valid until new documentation is published.

This operating manual explains the function and operation, describes
the installation and provides guidelines on how to connect the product.

This documentation is intended for instruction and should be retained
for future reference.

1.1.2 Terminology: System environment A and B

Terminology: System environment A and B1-][BA Einf Begriffsdefinition Sys A + B

The PSSu system can be used in two different system environments.
The module's application area is described in the chapter "Intended
Use" of the manual.

The distinction is made between

 PSSu in system environment A
 PSSu in system environment B

The distinction is based on the application area of the PSSu system.

PSSu in system environment A may be used in the

 Decentralised system PSSu I/O with SafetyBUS p
 Decentralised system PSSu I/O with ST fieldbuses such as CANopen,

DeviceNet

 Not in the automation system PSS 4000

PSSu in system environment B may be used in the

 Automation system PSS 4000, e.g. with the

– Decentralised system PSSu I/O with SafetyNET p
– Control system PSSu PLC
– Control system PSSu multi

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

1-1

1 Introduction

1.2 Overview of documentation

1.2Overview of documentation1200Overview of documentation1-][BA Einf Übersicht E-Modul_ohne Betrieb

1 Introduction

The introduction is designed to familiarise you with the contents, struc­ture and specific order of this manual.

2 Overview

This chapter provides information on the product's most important fea­tures.

3 Safety

This chapter must be read as it contains important information on in­tended use.

4 Function Description

This chapter describes the product's individual components.

5 Installation

This chapter explains how to install the product.

6 Wiring

This chapter describes the product's wiring.

7 Technical Details

This chapter contains the product's technical details and order refer­ence.

1-2

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

1 Introduction

1.3 Definition of symbols

1.3Definition of symbols1300Definition of symbols1-Einfhrung Zeichen

Information that is particularly important is identified as follows:

DANGER!

This warning must be heeded! It warns of a hazardous situation
that poses an immediate threat of serious injury and death and
indicates preventive measures that can be taken.

WARNING!

This warning must be heeded! It warns of a hazardous situation
that could lead to serious injury and death and indicates preven­tive measures that can be taken.

CAUTION!

This refers to a hazard that can lead to a less serious or minor
injury plus material damage, and also provides information on
preventive measures that can be taken.

NOTICE

This describes a situation in which the unit(s) could be damaged
and also provides information on preventive measures that can
be taken. It also highlights areas within the text that are of partic­ular importance.

INFORMATION

This gives advice on applications and provides information on
special features.

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

1-3

1 Introduction

1-4

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

2 Overview

2.1 Module structure

22000OverviewOverview2-2.1Module structure2100Module structure2-][BA Übersicht Aufbau

A module consists of

 Electronic module and
 Base module with

The base modules are the carrier units for the electronic modules and
are used to connect the field wiring. The electronic modules are inserted
on to the base modules and determine the module's function.

Details of the base modules that can be used are available in the chapter
entitled “Intended Use”.

– Screw terminals or
– Cage clamp terminals

2.1.1 Module features

Module features2-Geraetemerkmale_Zusatz BA Einleitung

][Merkmale_Ein_Aus SHT1

][Geraetemerkmal_T

][Merkmale_Zusatz ST/FS-Module Sys B

The product has the following features:

 1 Analogue current input

Current range:
0 … 0.6 A, single-pole, referenced to earth

 2 analogue current outputs

Current range:
0 .. 20mA, single-pole, referenced to earth

– Scaling of input current 1:100 and 1:200
– Evaluation via analogue input module with an input resistance =

115 Ohm, (e.g. PSSu E F AI I)

 T-type:

PSSu E AI SHT1-T: for increased environmental requirements

 For standard and failsafe applications in system environment B

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

2-1

2 Overview

2111

2212

2313

2414

11 21

12 22

13 23

14

O1+O0+

24

PSSu E
AI SHT1
312261
000000

001

O1-O0-

0VI0

(C) (C)

P S S u E
A I S H T 1

1

3

8

7

4

5

6

10

2

9

A

B

2.2 Front view

2.2Front view2200Front view2-BA_Fron tansicht

2-2

][BA_Frontansicht Legende SHT

Legend:

 A: Electronic module
 B: Base module
 1: Labelling strip with:

– Name of electronic module
– Order Number
– Serial number
– Hardware version number
–2D code

 2: Labelling strip for the terminal configuration on the base module
 3: Name of electronic module
 4: Connection level 1
 5: Connection level 2
 6: Connection level 3
 7: Connection level 4

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

2 Overview

2.2 Front view

 8: Square mounting holes (connection levels 1, 2, 3 and 4)

– With screw to loosen/tighten the screw terminal on base modules

with screw terminals

– With mechanism to operate the cage clamp on base modules with

cage clamp terminals

 9: Round connection holes (connection levels 1, 2, 3 and 4) for con-

necting the signal lines

 10: Mounting slot for colour marker to label the connection level (con-

nection levels 1, 2, 3 and 4)

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

2-3

2 Overview

2-4

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

3 Safety

3.1 Intended use

33000SafetySafety3-3.1Intended use3100Intended use3-][Gertebeschreibung SHT

][Gerätebeschreibung ST -Module Sys A + B

Bestimm_Verwend_ Zusatz-(T)

Bestimmung/Gertebeschreibung_Ausschluss

The module provides shunts to scale the current for analogue inputs.
The module may be used in conjunction with analogue current inputs
(e.g. PSSu E F AI I).

The module may be used for standard applications in system environ­ment A and B.

The module PSSu E AI SHT1-T is suitable for use where there are in­creased environmental requirements (see Technical Details).

Intended use includes making the electrical installation EMC-compliant.
Please refer to the guidelines stated in the "PSSuniversal Installation
Manual". The module is designed for use in an industrial environment. It
is not suitable for use in a domestic environment, as this can lead to in­terference.

Bestimm_Verwend_B asismodule

Bestimm_Basismodule Ser

Bestimm_Verwend_B asismodule-T

Bestimm_Basismodule Ser-T

The following is deemed improper use in particular:

 Any component, technical or electrical modification to the module
 Use of the module outside the areas described in this manual
 Use of the module outside the technical details (see chapter entitled

"Technical Details")

The PSSu E AI SHT1 module may be used in conjunction with the fol­lowing base modules:

 PSSu BP 1/8S
 PSSu BP 1/8C
 PSSu BP 1/12S
 PSSu BP 1/12C
 PSSu BP-C 1/8S
 PSSu BP-C 1/8C
 PSSu BP-C 1/12S
 PSSu BP-C 1/12C

The module PSSu E AI SHT1-T may be used in conjunction with the fol­lowing base modules:

 PSSu BP 1/8S-T
 PSSu BP 1/8C-T
 PSSu BP 1/12S-T
 PSSu BP 1/12C-T
 PSSu BP-C 1/8S-T
 PSSu BP-C 1/8C-T
 PSSu BP-C 1/12S-T
 PSSu BP-C 1/12C-T

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

3-1

3 Safety

3.2 Safety regulations

3.2Safety regulations3200Safety regulation s3-

3.2.1 Use of qualified personnel

Use of qualified personnel3-Sich Qualif. Personal

The products may only be assembled, installed, programmed, commis­sioned, operated, maintained and decommissioned by competent per­sons.

A competent person is someone who, because of their training, experi­ence and current professional activity, has the specialist knowledge re­quired to test, assess and operate the work equipment, devices,
systems, plant and machinery in accordance with the general standards
and guidelines for safety technology.

It is the company's responsibility only to employ personnel who:

 Are familiar with the basic regulations concerning health and safety /

accident prevention

 Have read and understood the safety guidelines given in this descrip-

tion

 Have a good knowledge of the generic and specialist standards ap-

plicable to the specific application.

3.2.2 Warranty and liability

Warranty and liability3-Sich Gewhrleistung

3.2.3 Disposal

Disposal3-Si ch Entsorgung

All claims to warranty and liability will be rendered invalid if:

 The product was used contrary to the purpose for which it is intended
 Damage can be attributed to not having followed the guidelines in the

manual

 Operating personnel are not suitably qualified
 Any type of modification has been made (e.g. exchanging compo-

nents on the PCB boards, soldering work etc.).

 In safety-related applications, please comply with the mission time t

M

in the safety-related characteristic data.

 When decommissioning, please comply with local regulations regard-

ing the disposal of electronic devices (e.g. Electrical and Electronic
Equipment Act).

3-2

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

4 Function Description

I0

O0+

O1+

0V

O0-

O1-

I

O1

I

O0

I

I0

R

1

R

2

4.1 Module features

44000Function DescriptionFunction Description4-4.1Module features4100Module features4-

4.1.1 Function description

Function description4-][Funktionsbeschreibung BA SHT1

The electronic module PSSu E AI SHT1 contains two shunts for scaling
an input current I

tion O0+) and I
inputs.

Scaling is applied during evaluation via an analogue input module with
an input resistance of 115 Ohm, (e.g. PSSu E F AI I)

 Scaling factor with resistance R

O0+/O0-):

: II0 = 1:100

I

O0

 Scaling factor with resistance R

O1+/O1-):

: II0 = 1:200

I

O1

(connection I0). The two current outputs IO0 (connec-

I0

(connection O1+) are evaluated by analogue current

O1

= 1.163 Ohm (connections

1+R2

= 0.583 Ohm (connections

2

Example:

 Input current I
 Output current I
 Output current I

I0

= 500 mA

at R1 + R2 = 5 mA

O0

at R2 = 2.5 mA

O1

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

4-1

4 Function Description

4-2

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

5 Installation

12,6 mm

76 mm

52,1 mm8,1 mm

67,7 mm

12,6 mm

56,1 mm 71,8 mm

0,8 mm

128,9 mm

72,6 mm

(2.051")(0.319")

(0.496")

(2.858")

(0.496")

(2.99")

(2.209") (2.827")

(0.031")

(5.075")

(2.665")

5.1 General installation guidelines

55000InstallationInstallation5-5.1General installation guidelines5100General installation guidelines5-][Montage BA E-Modul Allgemein

Please also refer to the PSSuniversal Installation Manual.

5.1.1 Dimensions

Dimensions5-][Abmessungen 1xR + 1xRL

Base modules with four connection levels:

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

5-1

5 Installation

12,6 mm

76 mm

52,1 mm8,1 mm

67,7 mm

82,0 mm 71,8 mm

0,8 mm

72,6 mm

(2.051")(0.319")

(2.858")

(0.496")

(2.99")

(3.228") (2.827")

(0.031")

(2.665")

12,6 mm
(0.496")

154,6 mm

(6.087")

5.1 General installation guidelines

Base modules with six connection levels:

5-2

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

5 Installation

[2]

[1]

[3]

5.2 Installing the base module

5.2Installing the base module5200Installing the base module5-][Montage Basismodul

Prerequisite:

 The head module must be installed.
 If the head module does not have an integrated power supply, a sup-

ply voltage module must be installed to the right of the head module.

Please note:

 For mechanical reasons it is not possible to mix base modules with

screw terminals and base modules with cage clamp terminals.

 All contacts should be protected from contamination.
 The mechanics of the base modules are designed for 50 plug in/out

cycles.

Procedure:

 We recommend that you wire up the base modules before inserting

the electronic modules.

 Slot the groove on the base module on to the mounting rail from be-

low [1].

 Push the base module back [2] until you hear it lock into position.
 On the mounting rail, slide the base module to the left until you hear

the two lateral mounting hooks on the adjacent module lock into po­sition [3].

Schematic representation:

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

5-3

5 Installation

[2]

[1]

[1]

5.3 Inserting and removing an electronic module

5.3Inserting and removing an electronic module5300Inserting and removing an electronic module5-][Elektronikmodul stecken und ziehen

Please note:

 Only insert on to base modules that are already installed.
 Preferably these base modules should be ready wired.
 Electronic modules with outputs may only be inserted and removed

when the load is switched off. Unforeseeable error reactions may be
triggered if modules are inserted and removed under load.

 When an electronic module is plugged into a base module for the first

time, one part of the coding element remains on the electronic mod­ule, while its counterpart is fixed on to the base module. This is how
the base module is coded.

 The mechanics of the electronic modules are designed for 50 plug in/

out cycles.

5.3.1 Inserting an electronic module

Inserting an electronic module5-][Elektronikmodul stecken

Procedure:

 The electronic module must audibly lock into position [1].
 Mark the electronic module using the labelling strips [2].

Schematic representation:

5-4

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

5 Installation

[1]

[2]

[1]

5.3 Inserting and removing an electronic module

5.3.2 Removing an electronic module

Removing an electronic module5-][Elektronikmodul ziehen

Procedure:

 Press the locking mechanisms [1] together simultaneously.
 Pull out the electronic module [2].

Schematic representation:

5.3.3 Changing an electronic module during operation

Changing an electronic module during operation5-][Montage BA Hot Swapping ST

It is possible to change an electronic module during operation. However,
changing an electronic module during operation may cause an ST com­munication error. The configuration data is retained when a module is
changed.

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

5-5

5 Installation

5-6

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

6 Wiring

DIN 5264-A

6.1 General wiring guidelines

66000WiringWiring6-6.1General wiring gu idelines6100Gene ral wiring guideline s6-][Verdrahtung BA Einleitung

][Verdrahtung ST analog

 Safe electrical isolation must be ensured for the voltage supply to the

sensors and actuators. Failure to do so could result in electric shock.

Please note:

 We recommend that you use shielded signal lines.
 On base modules with C-rail:

– Connect the shield to the terminals on the C-rail.
– Connect the C-rail with low impedance to the functional earth.

 On base modules without C-rail:

– Connect the shield as shown in the terminal configuration section.

The module connects the shield to the mounting rail.

– Connect the mounting rail to the functional earth via an earthing

terminal.

 In environments with strong EMC interference, base modules without

a C-rail provide better protection if the shield is connected.

][Verdrahtung Zusatz mit C

 Use copper wiring.
 The terminal configuration as stated on the front plate applies for base

modules with C-rail. The terminal configuration as stated in the tech­nical documentation applies for all other base modules.

6.1.1 Mechanical connection of the base modules

Mechanical connection of the base modules6-][Modulverdrahtung mech

Procedure:

 Use a flat blade screwdriver (DIN 5264-A)!

 Strip the wire back 8 mm.
 If necessary, label the connection level with a colour marker [3].
 Base module with screw terminals:

– Use a screwdriver to loosen the screw on the screw terminal [1]
– Insert the stripped cable into the round fixing hole [2], as far as it

will go.
– Tighten up the screw on the screw terminal.
– Check that the cable is firmly seated.

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

6-1

6 Wiring

2111

[1]

[3]

[2]

[4]

[5]

[6]

6.1 General wiring guidelines

 Base module with cage clamp terminals:

– Insert the screwdriver [4] into the square hole [1].
– Insert the stripped cable into the round fixing hole [2], as far as it

will go [5].
– Pull out the screwdriver [6].
– Check that the cable is firmly seated.

][Modulverdrahtung el Sys A + B

Please note:

 The minimum cable cross section for field connection terminals on the

2

base modules is 0.14 mm

 The maximum cable cross section for field connection terminals is:

– Digital inputs: 1.5 mm
– Digital outputs: 2.0 mm
– Inputs/outputs on the counter modules: 1.5 mm
– Analogue inputs/outputs: 1.5 mm
– Communication cables: 1.5 mm
– Test pulse outputs: 1.5 mm
– Power supply: 2.5 mm
– Functional earth: 2.5 mm

(AWG26)

2

(AWG16)

2

(AWG14)

2

(AWG16)

2

(AWG12)

2

(AWG12)

2

(AWG16)

2

(AWG16)

2

(AWG16)

6-2

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

6 Wiring

6.1 General wiring guidelines

 On base modules with screw terminals:

– If you use a multi-strand cable to connect the I/Os, it is recom-

mended that you use ferrules conforming to Parts 1 and 2 of DIN

46228, 0.14 ... 1.5 mm

To crimp the ferrules you can use crimp pliers (crimp form A or C)

conforming to EN 60947-1, such as the PZ 1.5 or PZ 6.5 from

Weidmüller, for example.
– Maximum torque setting: 0.8 Nm

 Use copper wiring.

2

, Form A or C, although this is not essential.

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

6-3

6 Wiring

2111

2212

2313

2414

2111

2212

2313

2414

6.2 Terminal configuration

6.2Terminal configuration6200Terminal configuration6-][Klemmenbelegung SHT1

Base module Terminal configuration

Screw terminals:
PSSu BP 1/8S
PSSu BP 1/8S-T

Without C-rail:

11: Output O0+

Cage clamp terminals:
PSSu BP 1/8C
PSSu BP 1/8C-T

Screw terminals:
PSSu BP-C 1/8S
PSSu BP-C 1/8S-T

Cage clamp terminals:
PSSu BP-C 1/8C
PSSu BP-C 1/8C-T

21: Output O1+

12: Output O0-

22: Output O1-

13-23: Shield connection
(13-23 linked within the base module)

14: Input I0

24: 0 V analogue
With C-rail:

11: Output O0+

21: Output O1+

12: Output O0-

22: Output O1-

13-23: C-rail supply,
shield connection
(13-23 linked within the base module)

14: Input I0

6-4

24: 0 V analogue

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

6 Wiring

2111

2212

2313

2414

2616

2515

2111

2212

2313

2414

2616

2515

6.2 Terminal configuration

Base module Terminal configuration

Screw terminals:
PSSu BP 1/12S
PSSu BP 1/12S-T

Cage clamp terminals:
PSSu BP 1/12C
PSSu BP 1/12C-T

Without C-rail:

11: Output O0+

21: Output O1+

12: Output O0-

22: Output O1-

13-23: Shield connection
(13-23-16-26 linked within the base
module)

14: Input I0

24: 0 V analogue

15: Output O0-

25: Output O1-

16-26: Shield connection
(13-23-16-26 linked within the base
module)

Screw terminals:
PSSu BP-C 1/12S
PSSu BP-C 1/12S-T

Cage clamp terminals:
PSSu BP-C 1/12C
PSSu BP-C 1/12C-T

With C-rail:

11: Output O0+

21: Output O1+

12: Output O0-

22: Output O1-

13-23: C-rail supply,
shield connection
(13-23-16-26 linked within the base
module)

14: Input I0

24: 0 V analogue

15: Output O0-

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

25: Output O1-

16-26: C-rail supply,
shield connection
(13-23-16-26 linked within the base
module)

6-5

6 Wiring

2111

2212

2414

2313

PSSu E AI SHT1

O0+

O0-

O1+

O1-

I0 0V

0V

I0+

2111

2212

2313

2414

PSSu E F AI I

0V

I0-

n.c.

n.c.

0V

I0+

2111

2212

2313

2414

PSSu E F AI I

0V

I0-

n.c.

n.c.

F1

6.3 Connecting the module

6.3Connecting the module6300Connecting the module6-][Ansc hluss SHT1

Input circuit
Current range 0 ... 600 mA

single-pole, referenced to earth

6-6

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

NOTICE

Input I0 must be protected with a circuit breaker F1, 1 A, charac­teristic C.

7 Technical Details

7.1 Technical details

77000Technical DetailsTechnical Details7-7.1Technical details7100Technical details7-][Technische Daten PSSu Analoge SHT

Technical details

Application range Standard
Support in system environment A no
Support in system environment B yes

Electrical data

Inputs

Number of analogue inputs 1
Type of analogue inputs Current
Input range 0 … 0.6 A
Max. power dissipation of the module 0.50 W
Max. current for max.120 s 2.0 A

Outputs

Number of analogue outputs 2
Output range 0 .. 20mA
Output variable error at 25° C 1.0 %
Scaling
Analogue output O0 1:100
Analogue output O1 1:200
Internal resistance
Connection O0+/O0- 1.163 Ohm
Connection O1+/O1- 0.583 Ohm

Environmental data
Climatic suitability EN 60068-2-14, EN 60068-2-1, EN 60068-2-2,

EN 60068-2-30, EN 60068-2-78

Ambient temperature in accordance with EN 60068-2-14 -40 - 70 °C T-type

0 - 60 °C base type

Storage temperature in accordance with EN 60068-2-1/-2 -40 - 70 °C
Climatic suitability in accordance with EN 60068-2-30,

EN 60068-2-78

Condensation temporary T-type

Max. operating height above sea level 2000 m base type

EMC EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,

Vibration to EN 60068-2-6
Frequency 10 - 150 Hz
Max. acceleration 1g
Shock stress

EN 60068-2-27 15g

EN 60068-2-29 10g

Protection type in accordance with EN 60529
Mounting (e.g. cabinet) IP54
Housing IP20
Terminals IP 20

93 % r. h. at 40 °C

not permitted base type

5000 m T-type

EN 61000-4-5, EN 61000-4-6, EN 61000-6-2,
EN 61000-6-4

11 ms

16 ms

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

7-1

7 Technical Details

7.1 Technical details

Environmental data
Airgap creepage in accordance with EN 60664-1,

EN 61131-2

Overvoltage category II
Pollution degree 2

Mechanical data

Housing material
Front PC
Bottom PC
Coding PA
Dimensions
Height 76.0 mm
Width 12.6 mm
Depth 60.2 mm
Weight 29 g
Mechanical coding
Type E
Colour light grey

Technische Daten_Satz No rmen

The standards current on 2009-10 apply.

7-2

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

7 Technical Details

7.2 Order reference

7.2Order reference7200Order reference7-Bestel ldaten

Order reference

Description Order no.

PSSu E AI SHT1
(Electronic module, base type)

PSSu E AI SHT1-T
(Electronic module, T-type)

][Bestelldaten Basismodule Analog mit -T

Base modules Order no.

PSSu BP 1/8S
(Base module without C-rail with screw terminals)

PSSu BP 1/8S-T
(Base module without C-rail with screw terminals, T-type)

PSSu BP 1/8C
(Base module without C-rail with cage clamp terminals)
PSSu BP 1/8C-T
(Base module without C-rail with cage clamp terminals,
T-type)
PSSu BP-C 1/8S
(Base module with C-rail with screw terminals)
PSSu BP-C 1/8S-T
(Base module with C-rail with screw terminals, T-type)
PSSu BP-C 1/8C
(Base module with C-rail with cage clamp terminals)
PSSu BP-C 1/8C-T
(Base module with C-rail with cage clamp terminals,
T-type)
PSSu BP 1/12S
(Base module without C-rail with screw terminals)
PSSu BP 1/12S-T
(Base module without C-rail with screw terminals, T-type)
PSSu BP 1/12C
(Base module without C-rail with cage clamp terminals)
PSSu BP 1/12C-T
(Base module without C-rail with cage clamp terminals,
T-type)
PSSu BP-C 1/12S
(Base module with C-rail with screw terminals)
PSSu BP-C 1/12S-T
(Base module with C-rail with screw terminals, T-type)
PSSu BP-C 1/12C
(Base module with C-rail with cage clamp terminals)
PSSu BP-C 1/12C-T
(Base module with C-rail with cage clamp terminals,
T-type)

312 261

314 261

312 600

314 600

312 601

314 601

312 610

314 610

312 611

314 611

312 618

314 618

312 619

314 619

312 620

314 620

312 621

314 621

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

7-3

7 Technical Details

7-4

Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

...

1001465-EN-03, 2012-02 Printed in Germany

© Pilz GmbH & Co. KG, 2011

[phone]
[e-mail]

Pilz GmbH & Co. KG
Felix-Wankel-Straße 2
73760 Ostfildern, Germany
Telephone: [phone]
Telefax: [phone]
E-Mail: [e-mail]
Internet: www.pilz.com

Technical support

In many countries we are
represented by our subsidiaries
and sales partners.

Please refer to our homepage
for further details or contact our
headquarters.

InduraNET p

®

, Pilz

®

, PIT

®

, PMCprotego

®

, PMI

®

, PNOZ

®

, Primo

®

, PSEN

®

, PSS

®

, PVIS

®

, SafetyBUS p

®

, SafetyEYE

®

, SafetyNET p

®

, the spirit of safety

®

are registered and protected trademarks

of Pilz GmbH & Co. KG in some countries. We would point out that product features may vary from the details stated in this document, depending on the status at the time of publication and the scope

of the equipment. We accept no responsibility for the validity, accuracy and entirety of the text and graphics presented in this information. Please contact our Technical Support if you have any questions.

Contact address