PHILIPS RQ1095, RQ1075 User Manual [fr]

K L

ENGLISH 6

FRANÇAIS 28

RQ1095, RQ1087, RQ1085, RQ1077, RQ1075

ENGLISH

Introduction

Thank you for buying this Philips shaver. Please read this user manual, as it contains information about the wonderful features of this shaver as well as some tips to make shaving easier and more enjoyable.

Important

Read this user manual carefully before you use the shaver, the Jet Clean System and the Power Pod. Save the user manual for future reference.

Danger

- Make sure the adapter does not get wet.

Warning

- Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.

- The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this causes a hazardous situation.

- These appliances are not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliances by a person responsible for their safety.

- Children should be supervised to ensure that they do not play with the appliances.

Caution

- Do not use the shaver, the Jet Clean System, the Power Pod or the adapter if it is damaged.

- Charge and store the shaver at a temperature between 5°C and 35°C.

ENGLISH 7

- Always put the protection cap on the shaver to protect the shaving heads when you are travelling.

- Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance.

- Only use the adapter supplied.

- If the adapter is damaged, always have it replaced with one of the original type in order to avoid a hazard.

- Only use the Jet Clean System with the original

HQ200 cleaning uid.

- Never immerse the Jet Clean System in water nor rinse it under the tap.

- Use and store the Jet Clean System at a temperature between 5°C and 35°C.

- Always place the Jet Clean System on a stable, level and horizontal surface to prevent leakage.

- Empty the cleaning chamber and clean it thoroughly by rinsing it with hot tap water every 15 days.

- Always place the Jet Clean System on a uid- resistant surface.

- The Jet Clean System thoroughly cleans but does not disinfect your shaver, therefore do not share the shaver with others.

- The cleaning chamber of the Jet Clean System is not dishwasher-proof.

- When the Jet Clean System is ready for use, do

not move it to prevent leakage of cleaning uid.

- Never immerse the Power Pod in water, nor rinse it under the tap.

ENGLISH8

Compliance with standards

- The shaver complies with the internationally approved IEC safety regulations and can be safely cleaned under the tap.

- These Philips appliances comply with all standards

regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this user manual, the appliances are safe to use based

on scientic evidence available today.

General

- The adapter transforms 100-240 volts to a safe low voltage of less than 24 volts.

Overview (Fig. 5)

A Protection cap B Shaving unit C Trimmer D Trimmer on/off slide E Shaver (RQ1090/RQ1062/RQ1060/RQ1052/

RQ1050)

F Shaver on/off button G Display H Shaver holder I Jet Clean System (RQ1005/RQ1000) J Jet Clean System on/off button K Cleaning symbol L Drying symbol M ’Cleaning chamber empty’ symbol N Cleaning chamber O Power Pod P Cleaning brush Q Adapter R Small plug

ENGLISH 9

The display

Before you use the shaver for the rst time, remove

the protective foil from the display.

The ve shaver types (RQ1090, RQ1062, RQ1060,

RQ1052 and RQ1050) have different displays, which

are shown in the gures below.

- RQ1090

- RQ1062/RQ1060

- RQ1052/RQ1050

Charging

- Charging takes approx. 1 hour.

- When you place the shaver in the Jet Clean System or in the Power Pod, the display automatically switches off after approx. 5 hours.

RQ1090

- When the shaver is charging, the minutes

indication and the plug symbol ash.

- The shaving minutes increase until the shaver is fully charged.

ENGLISH10

RQ1062/RQ1060

- When the shaver is charging, the plug

symbol ashes.

- First the arrowheads of the bottom charge level ash, then the arrowheads of the second level ash, and so on until the shaver is fully charged.

RQ1052/RQ1050

- When the shaver is charging, the battery symbol

ashes blue.

Battery fully charged

RQ1090

- When the battery is fully charged, the minutes indication is visible on the display and the plug symbol disappears from the display.

RQ1062/RQ1060

- When the battery is fully charged, all arrowheads and all charge level lights light up blue continuously and the plug symbol disappears from the display.

- When you remove the shaver from the Jet Clean System or the Power Pod, the arrowheads of the top charge level light up blue to indicate that the battery is full.

ENGLISH 11

RQ1052/RQ1050

- When the battery is fully charged, the battery symbol lights up blue continuously.

Battery low

RQ1090

- When the battery is almost empty (when there are only 5 or fewer shaving minutes left), the minutes indication and the plug symbol start to

ash.

- When you switch off the shaver, the shaving

minutes and the plug symbol continue to ash for

a few more seconds. You hear a beep when there are no minutes left.

RQ1062/RQ1060

- When the battery is almost empty (when there are only 5 or fewer shaving minutes left), the

battery symbol ashes red and the arrowheads of the bottom charge level ash blue.

- When you switch off the shaver, the battery symbol and the arrowheads of the bottom charge

level continue to ash for a few seconds.

RQ1052/RQ1050

- When the battery is almost empty (when there are only 5 or fewer shaving minutes left), the battery symbol lights up red.

- When you switch off the shaver, the battery

symbol starts to ash for a few seconds.

ENGLISH12

Remaining battery capacity

RQ1090

- The remaining battery capacity is indicated by the number of shaving minutes shown on the display.

RQ1062/RQ1060

- The remaining battery capacity is indicated by the

ashing arrowheads of a particular charge level

Clean shaver

For optimal shaving performance, we advise you to

clean the shaver after every use.

- The tap symbol ashes to remind you to clean the shaver.

Note: The displays of types RQ1062, RQ1060, RQ1052 and RQ1050 look different but show the same indication.

Replace shaving unit

For maximum shaving performance, we advise you

to replace the shaving unit every two years.

- To remind you to replace the shaving unit, the

shaving unit symbol ashes (all types) and you

hear a beep when you switch off the shaver (RQ1090 only). This happens at the end of 7 successive shaves to remind you to replace the shaving unit.

ENGLISH 13

Note: The displays of types RQ1062, RQ1060, RQ1052 and RQ1050 look different but show the same indication.

Travel lock

You can lock the shaver when you are going to travel. The travel lock prevents the shaver from being switched on by accident.

Activating the travel lock

1 Press the on/off button for 3 seconds to enter

the travel lock mode.

, The lock symbol appears on the display (all

types) and you hear a beep (RQ1090 only) to indicate that the travel lock has been activated.

Note: The displays of types RQ1062, RQ1060, RQ1052 and RQ1050 look different but show the same indication.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

, The motor starts running to indicate that the

travel lock has been deactivated.

The shaver is now ready for use again.

Note: When you place the shaver in the plugged-in Power Pod or Jet Clean System, the travel lock is automatically deactivated.

Blocked shaving heads

- If the shaving heads are blocked, the shaving unit symbol and the tap symbol with exclamation mark

ash. In this case, the motor cannot run because

the shaving heads are soiled or damaged.

ENGLISH14

Note: The displays of types RQ1062, RQ1060, RQ1052 and RQ1050 look different but show the same indication.

- When this happens, you have to clean the shaving unit or replace it.

- The shaving unit symbol and the tap symbol

with exclamation mark continue to ash until you

unblock the shaving heads.

Charging

Charging takes approx. 1 hour. A fully charged shaver has a shaving time of up to 65 minutes, which is enough for approx. 21 shaves. The actual shaving time is calculated by the shaver. If you have a heavy beard, the shaving time may be less than 65 minutes. The shaving time may also vary over time, depending on your shaving behaviour and beard type.

Quick charge

After the shaver has charged for 5 minutes, it contains enough energy for one shave.

Charging in the Power Pod

1 Put the small plug in the Power Pod.

2 Put the adapter in the wall socket.

3 Pull at the top of the lid (1) and remove it (2).

ENGLISH 15

4 First insert the top of the shaver into the

Power Pod (1) and then press the bottom part into the Power Pod (2).

Note: The shaver cannot be placed in the Power Pod when the protection cap is on the shaving unit.

, The display shows that the shaver is charging

(see chapter ‘The display’).

Charging in the Jet Clean System

1 Put the small plug in the Jet Clean System.

2 Put the adapter in the wall socket.

3 Place the shaver upside down in the holder

with the display pointing towards the front of the Jet Clean System.

Note: RQ1090,RQ1062,RQ1060 only: when you turn the shaver upside down, the indications on the display are also turned upside down so you can still see the remaining battery capacity.

4 Press the shaver tightly into the holder to lock

it into place.

Note: The shaver cannot be placed in the Jet Clean System when the protection cap is on the shaving unit.

, The display shows that the shaver is charging

(see chapter ‘The display’).

Using the shaver

Shaving

1 Press the on/off button once to switch on the

shaver.

ENGLISH16

, The display lights up for a few seconds.

2 Move the shaving heads over your skin. Make

both straight and circular movements.

- Shaving on a dry face gives the best results.

- Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system.

3 Press the on/off button once to switch off the

shaver.

, The display lights up for a few seconds and then

shows the remaining battery capacity (RQ1090/ RQ1062/RQ1060 only).

Trimming

You can use the trimmer to groom your sideburns and moustache.

1 Pull the shaving unit off the shaver.

2 Press the on/off button once to switch on the

shaver.

, The display lights up for a few seconds.

3 Press the trimmer slide forwards to slide out

the trimmer.

4 You can now start trimming.

5 Press the trimmer slide backwards to retract

the trimmer.

6 Press the on/off button once to switch off the

shaver.

, The display lights up for a few seconds and then

shows the remaining battery capacity (RQ1090/ RQ1062/RQ1060 only).

ENGLISH 17

7 Insert the lug of the shaving unit into the slot

in the top of the shaver (1). Then press the shaving unit downwards (2) to attach it to the shaver (‘click’).

Cleaning and maintenance

Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance.

- The best and most hygienic way to clean the shaver is in the Jet Clean System. You can also rinse the shaver under the tap or clean it with the brush supplied.

- Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.

- Clean the shaver after every shave for optimal shaving performance.

- You can clean the outside of the shaver with a damp cloth.

- Regular cleaning guarantees better shaving performance.

Cleaning the shaving unit in the Jet Clean System

The Jet Clean System has three cleaning programs: the eco program, the normal program and the intensive program. The shaver automatically chooses the appropriate cleaning program.

Preparing the Jet Clean System for use

Fill the cleaning chamber before rst use.

1 Put the small plug in the Jet Clean System.

ENGLISH18

2 Put the adapter in the wall socket.

, The holder automatically moves to the highest

position.

3 Simultaneously press the release buttons on

both sides of the cleaning chamber (1). Then lift the Jet Clean System off the cleaning chamber (2).

, The cleaning chamber remains behind.

4 Unscrew the cap from the bottle with cleaning

uid and remove the airtight seal.

5 Fill the cleaning chamber with HQ200 cleaning

uid up to the MAX indication.

6 Place the Jet Clean System back onto the

cleaning chamber.

Make sure the release buttons click back into place.

Using the Jet Clean System

1 Place the shaver in the holder.

, The display shows that the shaver is charging

(see chapter ‘The display’).

2 Press the on/off button on the Jet Clean

System to start the cleaning program.

, The shaver display stops showing the charging

indication.

+ 36 hidden pages