Cucina |
Food processor |
HR7723/00
HR7724/16
Philips Domestic Appliances and Personal Care
Service Manual
PRODUCT INFORMATION
-The food processors are equipped with mechanical and thermal safety switches.
-Product meets the requirements regarding interference suppression on radio and TV.
-After the product has been repaired, it should function properly and has to meet the safety requirements as laid down officially established at this moment.
Automatic resettable cut-out (part of item 7)
-To prevent damage due to overheating, the appliance has been equipped with an automatic cut-out system. This system will automatically cut off the power supply when the appliance overheats.
If the appliance suddenly stops running:
-Unplug the appliance
-Set the knob to position 0
-Let the appliance cool down for 15 minutes
-Plug the appliance in again
-Switch the appliance on again
Safety lock (item 1)
TECHNICAL INFORMATION |
|
|
- Motor power |
: HR7723 - 600 W |
|
|
HR7724 - 700 W |
|
- Voltage |
: 230 V |
|
|
: 110 V |
|
- Frequency |
: 50 / 60 Hz |
|
- Colour |
: White |
|
- Cordset |
: 125 cm |
|
- Speed settings |
: 2 speeds + pulse |
|
- Bowl capacity |
: 2.5 l dry ingredients |
|
|
1.0 l liquids |
|
- Blender capacity |
: 1.0 l liquids |
|
|
2.0 l (max. contents) |
|
- Speeds unloaded |
: blender drive shaft 17000 rpm (max) |
|
|
acc. drive shaft |
2150 rpm (max) |
|
acc. drive shaft |
1400 rpm (min) |
- Weight in fancy box : HR7723/24 - 5100 g |
||
- Dimensions |
: HR7723/24 - 420 x 280 x 360 |
|
(l x w x h) |
|
|
- SAP coding |
: HR7723/00 |
|
|
HR7724/16 |
|
-Place the lid on the bowl in the right position.
The appliance will only function if the arrow on the applinace is directly opposite the mark on the lid of the food processor bowl and the same holds for the other accessoires. The built-in safety lock will now be deblocked and you can turn the appliance on.
Note that if both the blender jar and the bowl have been correctly mounted, only the blender will function.
Important:
-If the appliance is used without the blender jar, the appliance will not function if the screw cap has not been screwed onto the attaching hole for the blender.
Published by Philips Domestic Appliances and Personal Care |
Printed in the Netherlands |
© Copyright reserved |
Subject to modification |
4322 277 01090 02/11
HR7723/00 / HR7724/16
DISASSEMBLYAND RE-ASSEMBLY ADVISE
-A separate drawing shows how to disconnect the speed selection knob.
-The blender coupling on the motor shaft has been provided with the customary left-hand thread.
The drive coupling (item 11) can be detached by means of a hammer and a screwdriver. Strike the screwdriver with a short sharp blow and remove the drive coupling. Or block the acc. drive wheel (item 23) and thereby the rotor shaft, by sticking a pin through the hole (5 mm dia.) in the bottom plate.
-The top housing (item 29) can be removed by detaching the snap connections by sticking a pin (or a screwdriver) through the small round holes (3 mm dia.) in the bottom plate (item 27) and the housing (item 12).
The arrows in the drawing show the locations of the holes.
-In order to replace the speed selection knob, the locking lever (item 33) must be placed in its lowest position.
-The accessory drive shaft (item 15) has a locking piece (item 14).
-The assembly of the accessories depends on the national version.
-For specific versions, the component configuration may differ from the one shown on the exploded view. However, the actual components can be distinguished by their code numbers.
-Make sure that all functions, including the safety devices, are working correctly after you have completed the repair.
REPAIR INSTRUCTION
- No specific issues
OPTIONAL (ACCESSORIES)
- No specific issues
|
|
L2 |
Speed High |
|
|
|
|
brown |
R |
and Pulse |
|
|
F1 |
|
|
|
red |
|
|
||||
|
|
|
M1 |
|
|
||
|
|
|
|
|
|
||
|
|
|
D1 |
F2 |
|
BF |
white |
|
|
|
Speed Low 1N5406 |
brown |
|||
|
|
|
F1 |
|
|||
MAINS |
|
R1 |
|
|
|
|
Rotor |
|
|
C1 |
|
|
|
||
|
|
470k |
|
|
B |
yellow |
|
|
|
|
|
black |
|||
|
|
|
|
|
F2 |
|
|
blue |
N |
L1 |
N1 |
|
violet |
N |
|
|
|
|
Change-over switch in braking position
HR7723 / HR7724
PARTS LIST
Pos |
Service code |
Description |
|
|
|
1 |
4203 065 62110 |
Print + switch lever |
2 |
4822 214 12762 |
Print plate brake |
3 |
4203 065 62120 |
Coupling lever |
4 |
4822 532 13008 |
Rubber piece |
5 |
4822 462 11074 |
Air tunnel |
7 |
4822 361 11081 |
Motor 230 V |
|
4822 361 11082 |
Motor 110 V |
8 |
4822 466 11949 |
Coupling fork |
9 |
4203 065 60300 |
Flex |
10 |
4822 502 14593 |
Motor screw assy |
11 |
4203 065 62130 |
Blender coupling |
12 |
4203 065 64570 |
Housing |
13 |
4822 214 12767 |
Print plate |
14 |
4822 402 11076 |
Locking piece |
15 |
4822 535 10548 |
Drive spindle |
16 |
4203 065 62070 |
Rubber sealing |
17 |
4822 466 11948 |
Locking plate |
18 |
4822 535 10549 |
Spindle assy |
19 |
4822 530 10492 |
Rubber tube |
20 |
4822 492 11649 |
Compression spring |
|
|
|
Pos |
Service code |
Description |
|
|
|
|
|
21 |
4822 528 11265 |
Coupling piece |
|
22 |
4822 358 10257 |
Tooth belt |
|
23 |
4822 528 11266 |
Belt wheel |
|
24 |
4822 520 10851 |
Bearing |
|
25 |
4822 466 11947 |
Mounting plate |
|
27 |
4203 065 64610 |
Bottom plate |
|
28 |
4203 065 64620 |
Blender cover |
|
29 |
4203 065 64630 |
Housing top |
HR7723 |
|
4203 065 64640 |
Housing top |
HR7724 |
30 |
4822 492 11648 |
Snap return spring |
|
31 |
4203 065 64600 |
Switch knob |
HR7723 |
|
4203 065 62180 |
Switch knob |
HR7724 |
33 |
4203 065 62200 |
Locking lever |
|
|
|
|
|
2-4