WARNING – To reduce the risk of FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:
1. Never use the appliance if the lamp housing is damaged, broken or missing.
2. Heed all warnings.
3. Do not look directly at lighted lamp.
4. If the appliance, power supply cord or cord has been damaged in any way, liquid has spilled or
objects have fallen into the appliance, the appliance has been exposed to rain or moisture, does
not operate normally or has been dropped or damaged, it should not be operated.
5. Read this user manual carefully before you use the appliance and save it for future reference.
6. Water and electricity are a dangerous combination. Do not use this appliance in wet
surroundings (e.g. in the bathroom or near a shower or swimming pool).
7. Make sure the adapter does not get wet.
8. Do not let water run into the appliance or spill water onto the appliance.
9. Do not immerse the appliance in water or rinse under the tap.
10. The adapter contains a transformer. Do not cut off the adapter to replace it with another plug,
as this causes a hazardous situation.
11. Only use the original adapter. If the adapter or any of the other accessories is damaged, do not
use. Call 1-866-832-4361 for assistance.
12. Do not use the adapter in or near a power outlet that contains an electric air freshener to
prevent damage to the adapter.
13. This appliance is for indoor use only.
14. Make sure the vents on the appliance remain open during use.
15. Protect the power cord from being walked on or pinched, particularly at plugs, outlet and point
where they exit from lamp.
16. The appliance has no on/off switch. To disconnect the appliance from the power source,
remove the plug from the wall outlet.
SAVE THESE INSTRUCTIONS
3
General
Buttons
First use
Menu
What’s in the box
Important information
Introduction
Icon explanation
Overview
Setting the clock time
Wake-up prole
10
11
12
6
7
FM
9
9
Lamp on/off
Radio on/off
Alarm on/off
Fall-asleep
16
17
18
19
Extra options
Snooze
Midnight light
Dawn duration time
20
21
22
Wake-up sound
Clock time
Display contrast
4
13
14
15
Demonstration mode
Charging your mobile phone
23
24
Storage25
Disposal25
Assistance25
90-Day Money-Back
Guarantee
26
Full Two-Year Warranty26
Troubleshooting27
5
What’s in the box
6
Important information
Warning
– Check if the voltage indicated on the adapter corresponds to the local voltage before you connect the appliance.
– This adapter transforms 100-240 volts to a safe, low voltage of less than 24 volts.
– The appliance is suitable for a voltage of 120 V AC and a frequency of 50/60 Hz.
– Close supervision is necessary when this appliance is used by, or near children or invalids.
– Children should be supervised to ensure that they do not play with the appliance.
Caution
– Do not drop the appliance on the oor, hit it hard or expose it to other heavy shocks.
– Place the appliance on a stable, level and non-slippery surface.
– Do not use the appliance at room temperatures lower than 50°F/ 10°C or higher than
95°F/35°C.
– Consult your doctor before you start using the appliance if you have suffered from or are suffering from serious depression.
– Do not use this appliance as a means to reduce your hours of sleep. The purpose of this appliance is to help you wake up more easily. It does not diminish your need for sleep.
– This appliance is only intended for household use, including similar use in hotels. Do not use
attachments not recommended by Philips North America LLC
General
– This appliance allows you to choose the light intensity level you want to wake up to.
– If you often wake up too early or with a headache, reduce the light intensity level and/or the
sunrise simulation time.
– If you share a bedroom with someone else, this person may unintentionally wake up from the
light of the appliance, even though this person is further removed from the appliance. This is the
result of differences in light sensitivity between people.
– The power consumption of the appliance is lowest when the radio and the lamp are turned off.
7
FCC Information
– This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
– This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
– This Class B digital apparatus complies with Canadian ICES-005.
8
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet from the support that
Philips offers, register your product at www.philips.com/welcome.
The Philips Wake-up Light helps you wake up more pleasantly. In the set sunrise simulation time
(default is 30 minutes), the light intensity of the lamp gradually increases to the set level and the light
color changes from deep morning red to bright daylight. The light gently prepares your body for
waking up at the set time. To make waking up an even more pleasant experience, you can use natural
wake-up sounds or the FM radio to wake up to.
The effects of the Wake-up Light
The Philips Wake-up Light gently prepares your body for waking up during the last 20 to 40 minutes
of sleep, depending on the sunrise simulation time you set. In the early morning hours our eyes are
more sensitive to light than when we are awake. During that period the relatively low light levels
of a simulated natural sunrise prepare our body for waking up and getting alert. People who use
the Wake-up Light wake up more easily, have a better overall mood in the morning and feel more
energetic. Because the sensitivity to light differs per person, you can set the light intensity of your
Wake-up Light to a level that matches your light sensitivity for an optimal start of the day.
For more information about the Wake-up Light, see www.philips.com.
Icon explanation
Wake-up prole
Wake-up soundFall-asleep
Clock timeNatural sounds
Display contrastRadio
LampDawn duration
Midnight lightRelaxing nature sounds
FM
FM radio
9
Overview
FM
Display
Menu buttons - press to activate
Navigating through the menu
Press the MENU button
to enter the menu
Press the + or – button
to select a menu setting
123
Note:
To exit the menu, either press the MENU button or wait for 30 seconds.
10
Press SELECT to confirm
16-20in/
40-50cm
Place the Wake-up Light 16-20in/40-50cm from your head, for example on a bedside table.
First use - placing the Wake-up light
First use - setting the clock time
You have to set the clock time when you plug in the appliance for the rst time. When there has
been a power failure, the set clock time will be saved for up to 8 hours, with a minimum of 4 hours.
1
4
2
3
5
11
Setting your wake-up prole
When you set your wake-up prole, you set the wake-up time (steps 1 – 6), the light intensity
(steps 7 and 8) and the sound level (steps 9 and 10) you want to wake up to. You can set two
different wake-up times, for example if you want to wake up at a different time in the weekend
than on weekdays. The procedure to set the wake-up prole and wake-up sound is the same for
both.
1
4
8
5
9
OFF
20
6
10
2
3
7
OFF
20
12
Setting your wake-up sound
You can use natural wake-up sounds or the FM radio as a wake-up sound. The Wake-up Light has
seven built-in natural sounds.
1
4
4
2
5
5
3
6
6
13
Adjusting the clock time
To set the clock time, choose between a 12-hour and a 24-hour clock and then adjust the time.
1
4
12H / 24H
5
2
67
3
8
14
Setting the display contrast
You can adjust the display contrast from level level 0 (off) to level 4. Choose a level that is optimal
for you to see the display at night. The Wake-up Light will automatically adjust the contrast level
when your bedroom becomes brighter.
12
4
3
4
1
15
Switching the lamp on/off
Press the lamp on/off button to switch on the lamp and use it as a bedside lamp. You can adjust the light
intensity by pressing the + and – buttons. To switch off the lamp, press the lamp on/off button again.
1
2
1
20
3
16
FM
Switching the FM radio on/off
Press the FM on/off button to switch on the FM radio.
1
2
FM
1X
3
4
1
FM / USBFM / USB
Note:
To scan radio frequencies automatically, press and hold the menu - or + button for approx. 2 seconds.
20
17
Switching the alarm on/off
Press alarm 1 or alarm 2 if you want to switch the alarm on or off. The corresponding icon appears
on the display when you switch on the alarm. It disappears when you switch off the alarm. When you
switch on the alarm, the hour indication starts to ash. If necessary, you can now adjust the alarm time.
1
3
4
2
5
Note:
If you want to adjust the light level or volume to wake up to, you have to use the menu.
See chapter ‘Setting your wake-up prole’.
18
Fall-asleep
To use the fall fall-asleep function you need to select a timer and a sound setting.
1. Press the fall-asleep button to switch on the fall-asleep function. The fall-asleep time ashes on the
display for a few seconds.
2. Press the + or – button to adjust the time (5 to 60 minutes). Press the ‘SELECT’ button to conrm
the timer setting.
3. The last used sound ashes on the display. Press the + or – button to select the sound
(OFF, relaxing sound 1 (R1), relaxing sound 2 (R2), radio). Press the ‘SELECT’ button to conrm
the sound setting.
To switch off the fall-asleep function, press the fall-asleep button again. The fall-asleep icon disappears
from the display.
Note: If you press the fall-asleep button without setting the time or the sound, the lamp goes on and
then dims gradually over 30 minutes.
1
5 - 60 min.
2
60 min
5
3
4
19
Snooze
When the alarm sound is played at the set time, you can tap on the top of the Wake-up Light to
snooze for a while. The lamp stays on, but the alarm sound stops. After 9 minutes, the alarm sound is
automatically played again.
1
9 min.
Note:
The alarm 1 or alarm 2 icon ashes on the display when the alarm is snoozed.
20
Midnight light
The midnight light can be effortlessly activated when tapping the top of the device two times
(two taps, not too hard or soft, about half a second apart). Its dim, subtle orange light is intended
to provide just enough light to nd your way in the dark.
To deactivate this function, tap the top twice again.
1
Notes:
- The midnight light function cannot be activated when the lamp is already on (because the lamp was
switched on, during the wake-up period, during snoozing and when the fall-asleep function is active).
- To disable the midnight light function, press the light on/off button for 5 seconds. ‘OFF’ appears on
the display.
- To enable the midnight light function again, press the light on/off button for 5 seconds. ‘ON’ appears
on the display.
21
Adjusting the dawn duration time
The dawn duration time is the time in which the light intensity of the lamp gradually increases to the
set level before the alarm sound is played. The default dawn duration time is 30 minutes, but you can
reduce the dawn duration time to 20-25 minutes or increase it to 35-40 minutes.
1. Simultaneously press and hold alarm 1 and alarm 2.
2. The default dawn duration time of 30 minutes appears on the display.
3. Press the + and – button to adjust the minutes.
1
+
2
40 min
20
3
22
Demonstration mode
If you want a quick demonstration (90 seconds) of the gradually increasing light intensity and sound
level, switch on the test function of the appliance.
1. Press and hold the alarm 1 or alarm 2 button for at least 3 seconds.
2. The appliance starts the demonstration of the corresponding alarm.
3. To switch off the demonstration, press and hold the previously pressed alarm button for
3 seconds again.
1
> 3 sec.
2
90 sec.
3
> 3 sec.
Audio feedback
When you press a menu button, you hear a click. If you do not want to hear clicks when you press
a button, press and hold the FM button for 5 seconds to switch off the audio feedback. You hear
one click as a conrmation. To activate, press and hold the FM button again. You hear two clicks to
conrm that the audio feedback is activated.
Button backlight
The menu buttons have a backlight to help you to nd the buttons. If you move your ngers close to
the buttons, the backlight lights up. If you don’t press the button, the backlight goes out after a few
seconds.
23
Charging your mobile phone
1
You can use the USB port to charge your mobile phone.
2
iPhone
17:45
24
24
Storage
– Clean the appliance with a soft cloth.
– Do not use abrasive cleaning agents, pads or cleaning solvents like alcohol, acetone, etc., as this
may damage the surface of the appliance.
– If the appliance will not be used for an extended period of time, remove the power cord from
the wall outlet and store the appliance in a safe, dry location where it will not be crushed,
banged, or subject to damage.
– Do not wrap the power cord around the appliance when storing it.
– This appliance has no other user-serviceable parts. For assistance, call 1-866-832-4361.
Disposal
Your product is designed and manufactured with high quality materials and components, which can
be recycled and reused. For recycling information, please contact your local waste management
facilities or visit www.recycle.philips.com
Assistance
www.philips.com/support
For assistance visit our website: www.philips.com/support or call toll free: 1-866-832-4361.
25
90-Day Money-Back Guarantee
If you are not fully satised with your Philips Wake-up Light, send the product back and we’ll refund
you the full purchase price.
The Wake-up Light must be shipped prepaid by insured mail, insurance prepaid, have the original sales
receipt, indicating purchase price and the date of purchase, and the money-back guarantee return
authorization form enclosed. We cannot be responsible for lost mail.
The Wake-up Light must be postmarked no later than 90 days after the date of purchase. Philips
reserves the right to verify the purchase price of the Wake-up Light and limit refunds not to exceed
suggested retail price.
To obtain a Money-Back Guarantee Return Authorization form, call 1-866-832-4361.
Delivery of refund check will occur 6-8 weeks AFTER receipt of returned product.
Full Two-Year Warranty
Philips North America LLC (USA) and Philips Electronics Ltd (Canada) warrant this new product
against defects in materials or workmanship for a period of two years from the date of purchase, and
agree to repair or replace any defective product without charge.
IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse, lack
of reasonable care, the afxing of any attachment not provided with the product or loss of parts or
subjecting the product to any but the specied voltage or batteries.*
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/support for assistance. It
is suggested that for your protection you return shipments of product by insured mail, insurance
prepaid. Damage occurring during shipment is not covered by this warranty.
NOTE: No other warranty, written or oral, is authorized by Philips North America LLC.
This warranty gives you specic legal rights, and you may also have other rights which vary from
state to state, province to province or country to country. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above exclusion and limitations may not
apply to you.
* Read enclosed instructions carefully.
In US Manufactured for: Philips Personal Health, a division of Philips North America LLC,
P.O. Box 10313, Stamford, CT 06904.