How it Works
Philips
Loading...
FW-V795
Service manual
85 pgs20.3 Mb1
User Manual
35 pgs1.03 Mb0

Philips FW-V795 User Manual

VCD MP3-CD Mini Hi-Fi System
FW-V795
FW-V795
pg 001-035/V795/21-Eng 4/16/02, 6:42 PM1
1
3139 115 21281
Optimum disc playability : ensuring excellent picture quality
Constantly improving performance
As the penetration of the CD system has increased, and new applications like CD-ROM and Video CD have become commonplace, Philips Components - as the CD technology inventor and as one of the major suppliers of CD player modules in the industry - has constantly improved the performance of its products.
One of the ways in which this benefits users is by optimum disc playability. This is an important parameter for CD players other than CD Audio, and especially for the Video CD applications, because any loss of data from the disc will at best cause disturbances in the reproduced picture, and at worst can cause the player to lose track so that disc playing fails.
Presenting Super Error Correction
To ensure consistently good results when playing Video CD discs of all quality grades and conditions, Philips has introduced further improvements in the system's playability. These developments together are called Super Error Correction, a proprietary Philips technology optimizing the system's ability to handle less­than-perfect discs with the minimum disturbance to normal playing.
By effectively eliminating virtually all errors arising under normal playing conditions, Super Error Correction ensures that the picture quality as seen by the user is independent of disc play. The video encoding and processing during mastering of the disc, and the MPEG-1 decoding and video encoding in the signal processing stages, are now the only limiting factors for picture quality.
2
pg 001-035/V795/21-Eng 4/16/02, 6:42 PM2
3139 115 21281
5
4
3 2
1
§ ∞ ≤ £ ™
¡ ) (
^
6
7
CHANGE
3
DISC
DCV
3
CHANGER
DISC
1
DISC DIRECT PLAY
DISC
2
DISC
3
OPEN• CLOSE
CD/CD-R/CD-RW COMPATIBLE
CD SYNCHRO RECORDING
8
VCD MINI HIFI SYSTEM
STANDBY-ON
FW-
VOLUME
9
ECO POWER
MUSIC LEVEL
BAND
SOURCE
CDR/DVD
INTERACTIVE VU METER
ON•OFF LEVEL
DYNAMIC AMPLIFICATION CONTROL
CLOCK•
TITLE/
MP3-CD
M
LBU
A
E
M
NA
C
B
P
N
R
U
T
E
R
DEMO STOP/ CLEAR
DISPLAY
S
E
E
R
T
P
N
V
E
E
L
T
I
E
T
X
R
P
T
PLAY•
PAUSE
S
A
L
E
M
G
B
U
A
N
I
R
N
C
U
H
T
•
PROG
TIMER
VCD PAL/
NTSC
TAPE AUX
REPLAY
CD 1•2•3
TAPE 1•2
AUTO
DUBBING REC
TUNER
LEVEL
VOLUME
MIC/
G
I
ATION - JOG
V
A
N
D
N
U
O
S
D
S
C
E
D
L
N
B
I
U
D
O
E
R
R
R
C
U
N
I
S
V
A
C
0
! @ #
$ % ^
*
TAPE 1
3
pg 001-035/V795/21-Eng 4/16/02, 6:42 PM3
TAPE 2
&
3
3139 115 21281
4
pg 001-035/V795/21-Eng 4/16/02, 6:42 PM4
3139 115 21281
Index
English ------------------------------------------------ 6
-------------------------------------------------------- 36
Bahasa Melayu ----------------------------------- 65
Bahasa Indonesia -------------------------------- 95
English
Bahasa Melayu
Bahasa Indonesia
pg 001-035/V795/21-Eng 4/16/02, 6:42 PM5
CAUTION
Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.
5
3139 115 21281
Contents
English
General Information
Environmental Information ................................ 7
Supplied Accessories ........................................... 7
Acknowledgement ............................................... 7
Safety Information ................................................ 7
Preparations
Rear Connections .......................................... 8–10
Inserting batteries into the remote
control .................................................................. 10
Controls
Controls on the system and remote
control ........................................................... 11–13
Basic Functions
Plug and Play ........................................................ 14
Demonstration mode ........................................ 15
Switching the system on ................................... 15
Switching the system to Standby mode ........ 15
Switching the system to Eco Power Standby
mode ..................................................................... 15
Power Saving Automatic Standby .................... 15
Display mode....................................................... 16
Volume Control .................................................. 16
Sound Navigation ........................................ 16–17
CD/VCD/MP3-CD Operations
Discs for Playback .............................................. 18
Loading Discs ...................................................... 19
Disc Playback ....................................................... 19
Replace discs during playback.......................... 19
Select a desired track/passage ......................... 20
Programming the disc tracks .................... 20–21
Repeat ................................................................... 21
Title/Album Name ............................................. 21
VIDEO CD
Adjusting the TV System ................................... 22
OSD – On Screen Display ............................... 22
Playing a Video CD with PBC ................... 22–23
Return ................................................................... 23
Digest .................................................................... 23
A-B Repeat .......................................................... 23
Zoom .................................................................... 23
Resume ................................................................. 24
Slow ....................................................................... 24
Vocal ...................................................................... 24
Key Control ......................................................... 24
Echo ....................................................................... 24
Radio Reception
Storing Preset Radio Stations ................... 25–26
Tuning to Preset Radio Stations ...................... 26
Erasing a Preset Radio Station ........................ 26
Changing Tuning Grid ........................................ 26
Tape Operation/Recording
Tape Playback ...................................................... 27
General Information on Recording ................ 28
Preparation for Recording ............................... 28
One Touch Recording/Recording the
mixed sound ........................................................ 28
CD/VCD/MP3-CD Synchro Recording..............
......................................................................... 28–29
Dubbing Tapes ..................................................... 29
Karaoke
Microphone Mixing ............................................ 29
Clock/Timer
View Clock .......................................................... 30
Clock Setting ....................................................... 30
Timer Setting ................................................ 30–31
External Sources
Listening to External Sources .......................... 32
Maintenance.............................................. 32
Specifications ........................................... 33
Troubleshooting ............................. 34–35
6
pg 001-035/V795/21-Eng 4/16/02, 6:42 PM6
3139 115 21281
General Information
IMPORTANT! PLEASE NOTE THAT THE VOLTAGE SELECTOR LOCATED AT THE REAR OF THIS SYSTEM IS PRESET AT 220V FROM THE FACTORY. FOR COUNTRIES THAT OPERATE AT 110V-127V, PLEASE ADJUST TO 110V-127V BEFORE YOU SWITCH ON THE SYSTEM.
Environmental Information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet).
Your system consists of materials which can be recycled and reused if disassembled by a specialised company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
Acknowledgement
Energy Star
As an ENERGY STAR Partner, Philips has determined that this product meets the ENERGY STARR guidelines for energy efficiency.
R
Supplied accessories
– Remote control – Batteries (two AA size) for remote control – AM loop antenna – FM wire antenna – AC power cord – One Video cinch cable – One cinch cable (GN/BU) – Power booster amplifier package:
– one power booster amplifier – one pair of speakers – AC power cord
Safety Information
● Before operating the system, check that the
operating voltage indicated on the typeplate (or the voltage indication beside the voltage selector) of your system is identical with the voltage of your local power supply. If not, please consult your dealer.
● Place the system on a flat, hard and stable
surface.
● Place the system in a location with adequate
ventilation to prevent internal heat build-up in your system. Allow at least 10 cm (4 inches) clearance from the rear and the top of the unit and 5 cm (2 inches) from each side.
● Do not expose the system, batteries or discs to
excessive moisture, rain, sand or heat sources caused by heating equipment or direct sunlight.
● If the system is brought directly from a cold to a
warm location, or is placed in a very damp room, moisture may condense on the lens of the disc unit inside the system. Should this occur, the CD player would not operate normally. Leave the power on for about one hour with no disc in the system until normal playback is possible.
● The mechanical par ts of the set contain self-
lubricating bearings and must not be oiled or lubricated.
● When the system is switched to Standby
mode, it is still consuming some power. To disconnect the system from the power supply completely, remove the AC power plug from the wall socket.
English
pg 001-035/V795/21-Eng 4/16/02, 6:42 PM7
7
3139 115 21281
Preparations
English
AM loop
antenna
speaker
(right)
E
F
LR
AUX/ CDR
IN
BOOSTER
OUT
SUBWOOFER
OUT
+
R
— —
L
+
SPEAKERS 6Ω
VIDEO OUT
(CVBS)
C
AM ANTENNA
Television
D
B
FM ANTENNA
VIDEO
L
AUDIO
OUT
R
IN
FM wire antenna
speaker
(left)
AC
MAINS
VOLTAGE SELECTOR
110V­127V
220V­240V
A
booster
speaker
(right)
BOOSTER IN
R
SPEAKERS 6Ω
—
RLR
—
DO NOT OPEN
CAUTION
RISK OF ELECTRIC SHOCK
NE PAS OUVRIR
AVIS
RISQUE DE CHOC ELECTRIQUE
POWER SWITCH
L
+
L
+
OFF
AC MAINS
VOLTAGE
SELECTOR
110V­127V
ON
220V­240V
Rear Connections
The type plate is located at the rear of the system.
A Pow er
Before connecting the AC power cord to the wall outlet, ensure that the following are done; – If your system is equipped with a Voltage Selector, set the VOLTAGE SELECTOR to the local power line voltage. – All other connections have been made.
booster speaker
(left)
VOLTAGE SELECTOR
110V­127V
220V­240V
AC power cord
AC power cord
WARNING! – For optimal performance, use only the original power cable. – Never make or change any connections with the power switched on.
To avoid overheating of the system, a safety circuit has been built in. Therefore, your system may switch to Standby mode automatically under extreme conditions. If this happens, let the system cool down before reusing it (not available for all versions).
8
pg 001-035/V795/21-Eng 4/16/02, 6:42 PM8
3139 115 21281
Preparations
B Antennas Connection
Connect the supplied AM loop antenna and FM antenna to the respective terminals. Adjust the position of the antenna for optimal reception.
AM Antenna
● Position the antenna as far as possible from a TV,
VCR or other radiation source.
FM Antenna
● For better FM stereo
reception, connect an outdoor FM antenna to the FM ANTENNA terminal.
C Speakers Connection
Front Speakers
Connect the speaker wires to the SPEAKERS (FRONT) terminals, right speaker to "R" and left speaker to "L", coloured (marked) wire to "+" and black (unmarked) wire to "-".
1
2
D Video Out Connection
Connect the VIDEO OUT (CVBS) terminal at the rear of the system to the TV or VCR VIDEO IN for viewing or recording.
Note: – To avoid magnetic interference, do not position the front speakers too close to the TV.
E Connecting other equipment to your
system
Connect the audio left and right OUT terminals of a TV, VCR, Laser Disc player, DVD player or CD Recorder to the AUX/CDR IN terminals.
Note: – If you are connecting equipment with a mono output (a single audio out terminal), connect it to the AUX/CDR IN left terminal. Alternatively, you can use a “single to double” cinch cable (still be mono sound).
F Power Booster Connection
VOLUME
7
6
BOOSTER IN
R
1
SPEAKERS 6Ω
RLR
2 4
DO NOT OPEN
CAUTION
RISK OF ELECTRIC SHOCK
NE PAS OUVRIR
AVIS
RISQUE DE CHOC ELECTRIQUE
L
POWER SWITCH
ON
OFF
–
+
AC MAINS
L
–
+
VOLTAGE SELECTOR
110V-
220V-
127V
240V
English
5
3
● Fully inser t the stripped por tion of the speaker
wire into the terminal as shown.
Notes: – For optimal sound performance, use the supplied speakers. – Do not connect more than one speaker to any one pair of +/- speaker terminals. – Do not connect speakers with an impedance lower than the speakers supplied. Please refer to the SPECIFICATIONS section of this manual.
pg 001-035/V795/21-Eng 4/16/02, 6:42 PM9
1 Connect the BOOSTER OUT (Right and
Left) terminals of the mini system to the power booster amplifier BOOSTER IN (Right and Left) terminals respectively.
2 Connect the speaker wires to the BOOSTER
SPEAKERS terminals, right speaker to "R" and left speaker to "L", coloured (marked) wire to "+" and black (unmarked) wire to "-".
9
3139 115 21281
Preparations
3 Set the VOLTAGE SELECTOR to the local
English
power line voltage.
4 Plug in the AC mains to the wall socket. 5 Switch on the POWER SWITCH to activate
the power booster amplifier.
6 Press STANDBY ON button to switch the
system ON or to Standby mode.
7 Rotate the VOLUME control to adjust the
loudness of the power booster amplifier.
Inserting batteries into the Remote Control
Insert two batteries (Type R06 or AA) into the remote control with the correct polarity as indicated by the + and - symbols inside the battery compar tment.
CAUTION! – Remove batteries if they are exhausted or not to be used for a long time. – Do not use old and new or different types of batteries in combination. – Batteries contain chemical substances, so they should be disposed off properly.
10
pg 001-035/V795/21-Eng 4/16/02, 6:42 PM10
3139 115 21281
Controls (main system’s illustration on page 3)
Controls on the system and remote control
1 ECO POWER
– to switch the system on or to Eco Power
Standby mode.
2 STANDBY ON y
– to switch the system on or to Standby mode.
3 DISPLAY SCREEN
– to view the current status of the system.
4 DISC TRAYS 5 DISC CHANGE
– to change disc(s).
6 DISC 1 / DISC 2 / DISC 3
– to select a disc tray for playback.
7 OPEN•CLOSE
– to open or close the disc tray.
8 INTERACTIVE VU METER
– to show the VU (volume unit) meter in music or
volume mode depending on the display mode selected.
9 VOLUME
– to increase or decrease the volume.
0 Tape Deck Operation
AUTO REPLAY
– to select continuous playback in either AUTO
PLAY or ONCE mode only.
DUBBING
– to dub a tape.
REC
– to start recording on tape deck 2.
! SOUND NAVIGATION
– to select the desired sound feature : DSC or
VAC.
@ JOG CONTROL
– to select the desired sound effect for the
selected sound feature.
DSC ..................DIGITAL, ROCK, POP, NEWAGE,
CLASSIC or ELECTRIC.
VAC ..................HALL, CONCERT, CINEMA,
DISCO, ARCADE or CYBER.
# INCREDIBLE SURROUND (IS)
– to activate or deactivate the surround sound
effect.
$ wOOx ON•OFF
– to select enhanced or normal wOOx sound
effect.
wOOx LEVEL
– to select a desired wOOx level : WOOX 1,
WOOX 2 or WOOX 3.
% MIC/LEVEL
– to connect microphone jack. – to adjust the mixing level for karaoke or
microphone recording.
^ ç
– to open the tape deck door.
& TAPE DECK 2 * TAPE DECK 1 ( SOURCE – to select the following:
VCD PAL/NTSC / (CD 1•2•3)
– to select disc tray 1, 2 or 3 (this system can
playback normal CD/VCD/MP3-CD format disc).
– (on the system only) to select corresponding
video output for NTSC or PAL system of your TV set (except Multi-system TV).
TUNER / (BAND)
– to select waveband : FM or MW.
TAPE / (TAPE 1• 2)
– to select tape deck 1 or 2.
AUX / (CDR/DVD)
– to select a connected external source :
CDR/DVD or AUX (auxiliary) mode.
English
pg 001-035/V795/21-Eng 4/16/02, 6:42 PM11
11
3139 115 21281
Loading...
+ 24 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use