Philips FTL13E Schematic

Colour Television Chassis

FTL13E

CL 16532149_000.eps

110703

Contents Page Contents Page

1. Technical Specifications and Chassis Overview 2

2. Safety Instructions, Warnings and Notes 5

3. Directions for Use 6

4. Mechanical Instructions 18

5. Service Modes, Error Codes, and Fault Finding 21

6. Wiring Diagram, Block Diagrams and Overviews Wiring Diagram 33 Block Diagram Supply and Supply Lines 34 Testpoint Overv. Aux Supply and Power Supply 35 Block Diagram Video 36 Testpoint Overview Small Signal Board 37 Block Diagram Audio and Control 38 I2C IC’s overview 39

7. Circuit Diagrams and PWB Layouts Diagram PWB Audio and Supply, DC Protection (Diagram A1) 40 47-48 Filters (Diagram A2) 41 47-48 Audio Amplifier Left High (Diagram A3) 42 47-48 Audio Amplifier Left Low (Diagram A4) 43 47-48 Audio Amplifier Right High (Diagram A5) 44 47-48 Audio Amplifier Right Low (Diagram A6) 45 47-48 Supply & DC Protection (Diagram A7) 46 47-48 SSB: Connector (Diagram B1) 49 76-87 SSB: IF, I/O Videoprocessing (Diagram B2) 50 76-87 SSB: Feature Box (PICNIC) (Diagram B3A)51 76-87 SSB: Falconic (Diagram B3B)52 76-87 SSB: Eagle (Diagram B3C)53 76-87 SSB: 2FH Interface (Diagram B3D)54 76-87 SSB: HOP (Diagram B4) 55 76-87 SSB: OTC-Flash (Diagram B5A)56 76-87 SSB: Backlight Control (Diagram B5B)57 76-87 SSB: OTC-Flash (Diagram B5C)57 76-87 SSB: Audio Demodulator (Diagram B6A)58 76-87 SSB: Dolby Digital Decoder (Diagram B6B)59 76-87 SSB: Dolby Pro Logic Processor (Diagram B6C)60 76-87

Copyright 2003 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.

SSB: DC/DC-Convertor (Diagram B12) 61 76-87 SSB: Tun1/Tun2 (Diagram B13) 62 76-87 SSB: I/O Eur (Diagram B14A)63 76-87 SSB: I/O Eur (Diagram B14B)64 76-87 SSB: 2FH I/O (Diagram B14C)65 76-87 SSB: Audio I/O (Diagram B14D)66 76-87 SSB: PIP-HIP (Diagram B15A)67 76-87 SSB: PIP (Diagram B15B)68 76-87 SSB: PIP-Muppet (Diagram B15C)69 76-87 SSB: VGA RGB (Diagram B19A)70 76-87 SSB: HDI A/D Convertor (Diagram B19C)71 76-87 SSB: EPLD Control (Diagram B19D)72 76-87 SSB: EPLD OSD (Diagram B19E) 73 76-87 SSB: EPLD I/O (Diagram B19F) 74 76-87 SSB: I/O 2 (Diagram B20) 75 76-87 LED/Switch Panel (Diagram LD) 88 89 Side I/O (Diagram O) 90 91 Top Control (Diagram P) 92 93 Aux Supply (Diagram SA) 94 95-98 Power Supply (Diagram SP1) 99 101-

Doubler (Diagram SP2) 100 101-

8. Electrical Alignments 103

9. Circuit Descriptions, Abbreviation List, and IC Data Sheets 109

10 Spare Parts List 134 11 Revision List 144

102

Published by WO 0367 Service PaCE Printed in The Netherlands Subject to modification EN 3122 785 13450

EN 2 FTL13E1.

Technical Specifications, Connections, and Chassis Overview

1. Technical Specifications, Connections, and Chassis Overview

Index of this chapter:

1. Technical Specifications

2. Connections

3. Chassis Overview

Note: Figures below can deviate slightly from the actual situation, due to the different set executions.

1.1 Technical Specifications

1.1.1 Vision

Display type : TFT LCD, 15:9 Screen size : 30-inch (76 cm) Resolution (HxV) : WXGA 1280(*3)x768 Contrast ratio : 350:1 Light output : 450 cd/m^2 LCD response time : 16 ms Viewing angle : 176 deg. (H)

: 176 deg. (V) Tuning system : PLL Colour systems : PAL B/G, D/K, I

: SECAM B/G, D/K, L/L’ AV (playback only) : NTSC 4.43/3.58 Channel selections : 100 presets

: UVSH Aerial input : 75 ohm, IEC-type Dimensions (WxHxD) in mm : 891x489x110

1.1.2 Sound

Sound systems : FM-mono, AM-mono

: 2CS B/G, D/K

: NICAM B/G, D/K, I,

L/L'

Maximum power : 2 x 10 W_rms (int.)

1.1.3 Miscellaneous

Mains voltage : 95 - 264 V_ac Mains frequency : 50 / 60 Hz Ambient temperature : +5 to +45 deg. C Maximum humidity : 90 % R.H. Power consumption :

- Normal operation : ≈ 160 W

- Standby : < 2 W

1.2 Connections

1.2.1 Side I/O (Left Bottom Side)

TOP CONTROLS

Light sensor

Red

iTV only

LRSTB

Audio S-VideoCVBS-

Video

Centre In

No function

L R

PC Input (VGA)

Audio Out

Audio In

Figure 1-1 Rear connections

Hosiden: SVHS (Input)

1 - Y Ground H 2 - C Ground H 3 - Y 1 V_pp / 75 ohm j 4 - C 0.3 V_pp / 75 ohm j

Cinch (Input)

- CVBS 1 V_pp / 75 ohm jq

- Audio - L 0.5 V_rms / 10 kohm jq

- Audio - R 0.5 V_rms / 10 kohm jq

Headphone (Output)

- Headphone 32 - 600 ohm / 10 mW ot

Volume Program

L R

P/CHMENU/OK

FM ANT

ServiceEXT. 1/2/3/4 Mains

CL 36532053_066.eps

150703

1.2.2 Audio receiver (if present)

Audio - In (Cinch)

C - Audio - Centre jq

Audio - Out (Cinch)

R - Audio - R 0.5 V_rms / 1 kohm kq L - Audio - L 0.5 V_rms / 1 kohm kq

Audio - Out (Cinch)

R - Audio - R 0.5 V_rms / 1 kohm kq L - Audio - L 0.5 V_rms / 1 kohm kq

Technical Specifications, Connections, and Chassis Overview

EN 3FTL13E 1.

1.2.3 VGA

VGA (Input)

Figure 1-2 VGA connector

1 - Red 0.7 V_pp / 75 ohm j 2 - Green 0.7 V_pp / 75 ohm j 3 - Blue 0.7 V_pp / 75 ohm j 4 - Ground H 5 - Ground H 6 - Ground H 7 - Ground H 8 - Ground H 9 - 5V_DC_OUT +5 V_dc k 10 - Ground H 11 - Ground H 12 - DDC_SDA j 13 - H-sync 0 - 5 V j 14 - V-sync 0 - 5 V j 15 - DDC_SCL j

Cinch (Input)

- Audio - L 0.5 V_rms / 10 kohm jq

- Audio - R 0.5 V_rms / 10 kohm jq

- Y 0.7 V_pp / 75 ohm jq

- Pb 0.7 V_pp / 75 ohm jq

- Pr 0.7 V_pp / 75 ohm jq

1.2.4 SCARTs

121

CL96532137_056.eps

202

171199

Figure 1-3 SCART connector

External 1: RGB/YUV and CVBS - In/Out

1 - Audio - R 0.5 V_rms / 1 kohm k 2 - Audio - R 0.5 V_rms / 10 kohm j 3 - Audio - L 0.5 V_rms / 1 kohm k 4 - Audio Ground H 5 - Audio Ground H 6 - Audio - L 0.5 V_rms / 10 kohm j 7 - Blue / U 0.7 V_pp / 75 ohm j 8 - CVBS-status 0 - 1.3 V: INT

4.5 - 7 V: EXT 16:9

9.5 - 12 V: EXT 4:3 j

9 - Video Ground H 10 - N.C. 11 - Green / Y 0.7 V_pp / 75 ohm j 12 - N.C. 13 - Video Ground H 14 - Video Ground H 15 - Red / V 0.7 V_pp / 75 ohm j 16 - Status / FBL 0 - 0.4 V: INT

1 - 3 V: EXT / 75 ohm j 17 - Video Ground H 18 - Video Ground H 19 - CVBS-out 1 V_pp / 75 ohm k 20 - CVBS-in 1 V_pp / 75 ohm j 21 - Shielding Ground H

External 2: CVBS and SVHS - In/Out (for Recorder)

1 - Audio - R 0.5 V_rms / 1 kohm k 2 - Audio - R 0.5 V_rms / 10 kohm j 3 - Audio - L 0.5 V_rms / 1 kohm k 4 - Audio Ground H 5 - Audio Ground H 6 - Audio - L 0.5 V_rms / 10 kohm j 7 - C-out 0.7 V_pp / 75 ohm k 8 - CVBS-status 0 - 1.3 V: INT

4.5 - 7 V: EXT 16:9

9.5 - 12 V: EXT 4:3 j 9 - Video Ground H 10 - Easylink (P50) jk 11 - Green 0.7 V_pp / 75 ohm j 12 - N.C. 13 - Video Ground H 14 - Video Ground H 15 - C-in 0.7 V_pp / 75 ohm j 16 - Status / FBL 0 - 0.4 V: INT

1 - 3 V: EXT / 75 ohm j 17 - Video Ground H 18 - Video Ground H 19 - CVBS-out 1 V_pp / 75 ohm k 20 - CVBS-in 1 V_pp / 75 ohm j 21 - Shielding Ground H

External 3: CVBS - In

1 - Ground k 2 - Audio - R 0.5 V_rms / 10 kohm j 3 - Ground k 4 - Audio Ground H 5 - Ground H 6 - Audio - L 0.5 V_rms / 10 kohm j 7 - N.C. 8 - CVBS-status 0 - 1.3 V: INT

4.5 - 7 V: EXT 16:9

9.5 - 12 V: EXT 4:3 j

9 - Video Ground H 10 - N.C. 11 - N.C. 12 - N.C. 13 - Video Ground H 14 - Video Ground H 15 - N.C. 16 - N.C. 17 - Video Ground H 18 - Video Ground H 19 - N.C. 20 - CVBS-in 1 V_pp / 75 ohm j 21 - Shielding Ground H

External 4: CVBS - In

1 - Ground k 2 - Audio - R 0.5 V_rms / 10 kohm j 3 - Ground k 4 - Audio Ground H 5 - Ground H 6 - Audio - L 0.5 V_rms / 10 kohm j 7 - N.C. 8 - CVBS-status 0 - 1.3 V: INT

4.5 - 7 V: EXT 16:9

9.5 - 12 V: EXT 4:3 j

9 - Video Ground H 10 - N.C. 11 - N.C. 12 - N.C. 13 - Video Ground H 14 - Video Ground H 15 - N.C. 16 - N.C. 17 - Video Ground H 18 - Video Ground H 19 - N.C. 20 - CVBS-in 1 V_pp / 75 ohm j

EN 4 FTL13E1.

21 - Shielding Ground H

Aerial - In

- IEC-type Coax, 75 ohm D

1.3 Chassis Overview

Technical Specifications, Connections, and Chassis Overview

LED / MAINS SWITCH PANEL

AUDIO AMPLIFIER

SIDE I/O PANEL

Figure 1-4 PWB location

TOP CONTROL PANEL

AUX SUPPLY

POWER SUPPLY

SMALL SIGNAL PANEL

CL 36532053_054.eps

090703

Safety Instructions, Warnings, and Notes

2. Safety Instructions, Warnings, and Notes

EN 5FTL13E 2.

2.1 Safety Instructions

Safety regulations require that during a repair:

• Connect the set to the mains via an isolation transformer (> 800 VA).

• Replace safety components, indicated by the symbol h, only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard.

Safety regulations require that after a repair, the set must be returned in its original condition. Pay in particular attention to the following points:

• Route the wire trees correctly and fix them with the mounted cable clamps.

• Check the insulation of the mains lead for external damage.

• Check the strain relief of the mains cord for proper function.

• Check the electrical DC resistance between the mains plug

and the secondary side (only for sets which have a mains isolated power supply):

1. Unplug the mains cord and connect a wire between the

two pins of the mains plug.

2. Set the mains switch to the "on" position (keep the

mains cord unplugged!).

3. Measure the resistance value between the pins of the

mains plug and the metal shielding of the tuner or the aerial connection on the set. The reading should be between 4.5 Mohm and 12 Mohm.

4. Switch "off" the set, and remove the wire between the

two pins of the mains plug.

• Check the cabinet for defects, to avoid touching of any inner parts by the customer.

2.2 Warnings

• All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD w). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are connected with the same potential as the mass of the set by a wristband with resistance. Keep components and tools also at this same potential. Available ESD protection equipment: – Complete kit ESD3 (small tablemat, wristband,

connection box, extension cable and earth cable) 4822 310 10671.

– Wristband tester 4822 344 13999.

• Be careful during measurements in the high voltage

section.

• Never replace modules or other components while the unit is switched "on".

• When you align the set, use plastic rather than metal tools. This will prevent any short circuits and the danger of a circuit becoming unstable.

– Complete kit ESD3 (small tablemat, wristband,

connection box, extension cable and ground cable) 4822 310 10671.

– Wristband tester 4822 344 13999.

• Never replace modules or other components while the unit

is 'on’.

• Measure the voltages and waveforms with regard to the

chassis (= tuner) ground (H), or hot ground (I), depending on the tested area of circuitry. The voltages and waveforms shown in the diagrams are indicative. Measure them in the Service Default Mode (see chapter 5) with a colour bar signal and stereo sound (L: 3 kHz, R: 1 kHz unless stated otherwise) and picture carrier at 475.25 MHz (PAL) or

61.25 MHz (NTSC, channel 3).

• Where necessary, measure the waveforms and voltages

with (D) and without (E) aerial signal. Measure the voltages in the power supply section both in normal operation (G) and in standby (F). These values are indicated by means of the appropriate symbols.

• The semiconductors indicated in the circuit diagram and in the parts lists, are interchangeable per position with the semiconductors in the unit, irrespective of the type indication on these semiconductors.

2.3.2 Schematic Notes

• All resistor values are in ohms and the value multiplier is often used to indicate the decimal point location (e.g. 2K2 indicates 2.2 kohm).

• Resistor values with no multiplier may be indicated with either an "E" or an "R" (e.g. 220E or 220R indicates 220 ohm).

• All capacitor values are expressed in micro-farads (µ= x10^-6), nano-farads (n= x10^-9), or pico-farads (p= x10^-

12).

• Capacitor values may also use the value multiplier as the decimal point indication (e.g. 2p2 indicates 2.2 pF).

• An "asterisk" (*) indicates component usage varies. Refer to the diversity tables for the correct values.

• The correct component values are listed in the Electrical Replacement Parts List. Therefore, always check this list when there is any doubt.

2.3 Notes

2.3.1 General

• In order to prevent damage to ICs and transistors, avoid all high voltage flashovers.

• All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD, w). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are connected with the same potential as the mass of the set by a wristband with resistance. Keep components and tools also at this potential. Available ESD protection equipment:

EN 6 FTL13E3.

Preparation

Wall mounting instructions

For the wall mounting instructions follow the

illustrated steps xx to xx printed on the

separate template.

Make sure that the wall mount is being fixed

securely enough so that it meets safety

standards.The weight of the TV (excl.

packaging) is about 17 kg.

How to mount the supplied stand, see the

separate leaflet.

Note: other (not supplied) stands are optional

accessories. Consult your dealer.éPlace or hang the TV wherever you want,but

make sure that air can circulate freely through

the ventilation slots. Do not install the TV in a

confined space such as a book case or a

simular unit.

To prevent any unsafe situations, no naked

flame sources, such as lighted candles, should

be placed on or in the vicinity.Avoid heat,

direct sunlight and exposure to rain or water.

The equipment shall not be exposed to

dripping or splashing and no objects filled with

liquids, such as vases,shall be placed on it.

“

Insert the aerial plug firmly into the aerial

socket x at the bottom of the TV. For best

picture quality use the suppressor-aerial cable

supplied.‘To connect your computer, see p. 20.

To connect other peripherals, see p. 17.

If you dispose of a Cinema Link combination

(Cinema Link Audio receiver and/or Cinema

Link video recorder and/or DVD player), see

the separate supplied instruction manual.

In order to obtain the best result, please use

only the supplied antenna cables between the

TV and videorecorder, and between

videorecorder and antenna connector.(Insert the mains cord supplied into the mains

at the bottom of the TV and in the wall socket

having a mains voltage of 220-240V.

To prevent damaging the power (AC) cord

which could cause a fire or electric shock, do

not place the TV on the cord.

Remote control

: Insert the 2 batteries

supplied (Type R6-1,5V).

The batteries supplied do

not contain the heavy

metals mercury and

cadmium. Please check on

how to dispose of

exhausted batteries

according to local regulations.

Switch the TV on

: Press the power switch B

at the right side of the TV.

An indicator on the front of the TV lights up

and the screen comes on. If the TV is in

standby mode, press the

-P+

keys or the B

key on the remote control.

min.

Keys on top of the TV

Should your remote be lost or broken you can still

change some of the basic settings with the keys on top

of your TV.

Press:

• the V

key to adjust the volume;

• the

-P/CH+

keys to select the TV channels or sources.

The

MENU/OK

key can be used to summon the main

menu without the remote control.

Use:

• the V - and + keys and the

P/CH-

and

P/CH+

keys

to select menu items in the directions as shown;

• the

MENU/OK

key to confirm your selection.

Note:

When activated via the

MENU/OK

key on top of the TV,

only

Exit

lets you dismiss the menu.

Navigate to

Exit

and press the

MENU/OK

key.

MENU/OK - V + - P/CH +

Setup

Install

Exit

Picture Sound Features

Contents

Preparation ...................................................................................... 2

Keys on top of the TV ................................................................... 2

Your remote control .................................................................. 3-4

To use the menus ........................................................................... 5

Select the menu language and country ..................................... 5

Store TV channels .......................................................................... 6

Automatic installation ............................................................6

Manual installation................................................................... 6

Give name ................................................................................. 7

Reshuffle the programme list................................................. 7

Select favourite TV channels ................................................. 7

TV setup menu ............................................................................... 7

General ...................................................................................... 8

Source ........................................................................................ 9

Decoder .................................................................................... 9

Demo ............................................................................................... 9

Installation

TV menu

Picture menu .................................................................... 10-11

Sound menu ........................................................................... 11

Features menu................................................................. 11-12

NEX

IEW

/Teletext guide ...................................................... 13-14

Teletext ..................................................................................... 15-16

Connect peripheral equipment

Connecting and selecting equipment ............................... 17-20

Audio and Video equipment keys ............................................. 21

Record with your recorder with Easy Link ........................... 21

Tips ................................................................................................ 22

Operation

EasyLink features are based on the “one touch operation” approach.This

means that a sequence of actions are executed at the same time in both the

television and the video cassette recorder, provided both are fitted with the

EasyLink function and connected with the eurocable supplied with your video

recorder.

End of life directives

Philips is paying a lot of attention to

producing environmentally-friendly in

green focal areas.Your new TV contains

materials which can be recycled and

reused. At the end of its life specialised

companies can dismantle the

discarded TV to concentrate the

reusable materials and to minimise

the amount of materials to be

disposed of.

Please ensure you dispose of your old

TV according to local regulations.

Help?

If this instruction manual does

not give an answer or if ‘Tips’ do

not solve your TV problem, you

can call your Local Philips

Customer or Service Centre. See

the supplied World-wide

guarantee booklet.

Please, have the Model and

Product number which you can

find at the back of your

television set or on the

packaging, ready, before calling

the Philips helpline.

Model: 30PF9975

Product No: ...........................................

Care of the screen

See Tips, p. 22.

EnglishDeutschFrançaisNederlandsItaliano

∂ППЛУИО¿

3. Directions for Use

Directions for Use

i On Screen information

Press to display (when available) information about the selected TV

channel and programme.

Menu/Remote control info

When a menu is on screen, press

to display info on the selected menu

item.While the menu info is displayed, press any key to display remote

control info.The normal function of the key is not executed.

no function

h Active control

see p. 11.

q Picture format

Press this key repeatedly or press the cursor up/down to select another

picture format:Auto format, Super zoom, 4:3, Movie Expand 14:9,Movie

Expand 16:9, Subtitle zoom,Wide screen or 16:9.

Auto format makes the picture fill the screen as much as possible.

In case of subtitles in the bottom black bar,Auto format makes the

subtitles visible.

In case of a broadcaster logo in the corner of the top black bar, the logo

disappears from the screen.

Super zoom removes the black bars on the sides of 4:3 programs with

minimal distortion.

When in Movie Expand 14:9, Movie Expand 16:9, Super zoom or Subtitle

zoom picture format, you can make subtitles visible with the cursor

up/down.

Note:With signals via

EXT5

or the

VGA IN

connector less picture formats are

selectable.

Auto format Super zoom 4:3 Movie Expand 14:9

Movie Expand 16:9 Subtitle zoom Wide screen 16:9

Select

VCR DVD SAT AMP CD

123

456

789

‡π

†

Active Control

Use of the remote control RC4301

B Standby

Press to switch the TV on or off.

When switched off, a red indicator on

the TV lights up.When acquiring

NEX

IEW

, see p. 14,an orange

indicator lights up and after a period

of max. 1 hour the TV is switched to

full standby and the red indicator

lights up.

®Ò‡π†

Audio and Video equipment keys,

see p. 21.

® Instant record

See Record with your recorder

with EasyLink, p. 21.

U Time display

The time is displayed on the

screen.

Q Surround mode

Incredible surround

With stereo transmission, and

when Incredible surround is

selected, it seems as though the

loudspeakers are spread further

apart from one another.

Virtual Dolby surround

Optimal with Dolby surround

signals. Enables you to

experience the effect of Dolby

surround Pro Logic, reproducing

a rear sound effect. See Sound

menu, 3D effect, p. 11.

Note:You can make the same

selection in the Sound menu,

surround mode, p. 11.

Ì Cinema Go

See separate Cinema Link

booklet supplied.

NEX

IEW

On/Off see p. 13

S Freeze

To freeze the picture.

Dependent on the input signal,

the function may not be possible.

VCR DVD SAT AMP CD

See ‘Audio- and Video equipment

keys’, p. 21.

v Select your computer or

other peripherals

See p. 18.

x Pixel Plus demo

on/off

In the right part Pixel Plus and

Digital Natural Motion are

switched on.

b Teletext

On/Off see p. 15

Press this key

• to activate your choice, when in

the menus.

• to display the programme list.

Main menu

on/off see p. 5

To adjust the volume.¬Interrupt the sound or restore it.

P Programme selection

To browse through the TV

channels and sources stored in

the favourite list.

0/9 Digit keys

To select a TV channel.

For a two digit programme

number,enter the second digit

before the dash disappears.To

switch immediately to a selected

one digit TV channel, keep the

digit key pressed a bit longer.

0 Previous TV channel

Press to display the previously

selected TV channel.

Note: For most keys pressing a key once will activate the function. Pressing a second time will de-activate it.

When a key enables multiple options, a small list will be shown.Press repeatedly to select the next item in the list.

The list will be removed automatically after 4 seconds or press

to remove immediately.

Remark: in VGA mode only some keys are valid.

Select

VCR DVD SAT AMP CD

123

456

789

‡π

†

Active Control

EN 7FTL13E 3.

EN 8 FTL13E3.

Select

Automatic install

in the Install menu.

Note: All channels must be unlocked in order to autoprogram. If

requested, enter your code to unlock all channels. (See TV,

Features menu, Childlock, p. 12.)

Press the cursor down.

The autoprogramming option label

Start

appears.

“

Press the cursor right.

‘

The message

Searching

appears and the progress of

autoprogramming is displayed.

If a cable system or a TV channel which broadcasts ACI

(Automatic Channel Installation) is detected, a programme list

appears.Without ACI broadcast,the channels are numbered

according your language and country selection.You can use

Reshuffle to renumber them. See p. 7.

It is possible that the cable company or the TV channel displays a

broadcast selection menu. Layout and items are defined by the cable

company or the TV channel. Make your choice with the cursor and

press the

key.

After language and country are set correctly, you can now search for and store the TV channels in two

different ways:using Automatic Installation or Manual Installation (tuning-in channel by channel).

Select your choice with the cursor right.

Automatic install

Install Start

Install

Manual installation

Automatic installation

Searching for and storing TV channels is done channel by

channel.You must go through every step of the Manual

Installation menu.

Select

Manual install

in the Install menu.

Press the cursor down.

Follow the instructions on screen.

Note: Search or direct selection of a TV channel.

If you know the frequency, the C- or S-channel number, enter the

3 or 2 digits of the frequency or the channel number directly with

the digit keys 0 to 9 (e.g. 048).Press the cursor down to proceed.

Repeat to search for another TV channel.

Manual install

Install

Selection mode

System

Programme

Fine tune

Store

Store TV channels

To use the menus

Press the

key on the remote control to summon the

main menu.At any moment you can exit the menu by

pressing the

key again.

Note: If you have connected equipment with Cinema Link, more

menu items are present.

Use the cursor in the up/down direction to select the

Setup, Demo

Install

menu.

Use the cursor left/right to select

Picture

Sound

Features

Note: Sometimes not all the menu items are visible on the screen

(indicated by a cluster of blue balls). Use the cursor down or right

to reveal all items.

“

Use the cursor in the left/right direction to select the menu

item.‘Use the cursor up/down again to select the control you

want to select or to adjust.

Note: Items temporary not available or not relevant are displayed in a

light grey colour and cannot be selected.

Select

VCR DVD SAT AMP CD

‡π

†

cursor to select

adjustments

key to

activate

return or switch

main menu on/off

Installation

Press the

key on the remote control.

Use the cursor down to select

Install

“

Use the cursor right to select

Language

Follow the instructions on screen.

‘

Use the cursor up/down to select your preferred language

and press the

key to confirm your selection.

(

Use the cursor right to select

Country

Select the country where you are now located and press

the

key.

Select

Other

when none of the countries applies.

Proceed with the

Install

menu.

Setup

Demo

Install

Picture Sound Features

Install

Language Country Automatic Manual Give name Reshuffle Favourite

install install programmes

The installation menu contains the following items:

EasyLink

If your video recorder has an EasyLink function, during installation, the language, country and available channels are

automatically transmitted to the video recorder.

Language

English

Deutsch

Français

Install

Country

Austria

Belgium

Croatia

Install

Select the menu language and country

Directions for Use

General

Menu background

Select

Ye s

to turn the menu background

on or off.

Factory settings

This resets the picture and sound settings to

their predefined factory values, but maintains

the channel installation settings.

NEX

IEW

provider

Select a TV broadcaster that provides

NEX

IEW

data. How to make use of

NEX

IEW

see p. 13.

OSD (On Screen Display)

Select

OSD

Select

Normal

to activate extended channel

and programme information.

Minimum

will

display reduced channel information.

Note:When subtitles is switched on, see Features,

p.12, display of the programme number is not

possible

Programme title

Select

Programme title Yes

When selected

Ye s

, after the selection of a TV

programme or after pressing the i key on

the remote control, a TV channel which

broadcasts teletext may transmit the name of

the TV channel or the programme title.

When selected

, the programme title will

only appear after pressing the i key, and not

after the selection of a TV channel.

Teletext level 2.5

Some broadcasters offer the opportunity to

see more colours, other background colours

and nicer pictures in the teletext pages.

Select

Teletext level 2.5

Press the cursor right to select

Teletext level

2.5 On

to take advantage of this feature.

“

Press the cursor right again to select

Teletext

level 2.5 Off

if you like the more neutral

teletext layout.

The selection made is valid for all channels

which broadcast teletext level 2.5.

Note: It may take a few seconds before teletext

broadcast switches over to Teletext level 2.5.

Auto Surround

Sometimes the broadcaster transmits special

signals for Surround Sound encoded

programmes.

The TV automatically switches to the best

surround sound mode when

Auto Surround

switched

Set/Change code

The Child lock feature (see TV, Features, p. 12)

allows you to lock channels to prevent others

from watching certain programmes.To watch

locked channels, a 4-digit code must be

entered.The Set/Change code menu item

allows you to create or change a Personal

Identification Number (PIN).

Select

Set/Change code

If no code exists yet, the menu item is set to

Set code

If a code has previously been entered, the menu

item is set to

Change code

. Follow the

instructions on screen.

Important:You have forgotten your code !

Select

Change code

in the General menu and

press

Press the cursor right and enter the overriding

code 8-8-8-8.

“

Press the cursor again and enter a new

personal 4-digit code.The previous code is

erased and the new code is stored.

This menu allows you to change various settings that are presumably adjusted less frequently than most

other settings.

Press the

key on the remote control to get information about the selected menu item.

It is possible to change the name stored in the

memory or to assign a name to a TV channel or

external for which a name has not yet been

entered.A name with up to 5 letters or numbers

can be given to the programme numbers 0 to 99.

Note : It is not possible to rename the VGA source.

Select

Give Name

in the Install menu and

press the cursor down.

Select the programme number.

Note: keep the cursor up/down pressed to scroll

through the programme list quickly.“Press the cursor right.

A keyboard appears on the screen.

Press the cursor right to enter the keyboard.

Press the cursor up/down, left/right to select

the first character and press

. Repeat for

every character you want to enter.

Select

Space

to enter a space;

Delete

to erase

the highlighted character in the name entered;

Shift

to display upper- or lowercase characters

on the keyboard;

Special

to display special

characters on the keyboard. Press

confirm.

‘

Press the cursor left repeatedly when you have

finished the name giving.

(

Select another programme number and repeat

steps

“

‘

Give name

pπ

® Space ® Delete

ABCDEFG 123

HIJKLMN 456

OPQRSTU 789

VWXYZ 0

® Shift ® Special

Give name

Install

VCR1

BBC1

BBC2

CNN

TVE

.....

Reshuffle the programme list

You can change the order of the stored TV

channels.

Select

Reshuffle

in the Installation menu.

Follow the instructions on screen.

Select Favourite TV channels

A VGA source always belongs to the list of

Favourite programmes

Select

Favourite programmes

in the Install

menu.

Select your programme number with the

cursor up/down.

“

Select

Ye s

with the cursor right.

‘

Repeat

and

“

for every TV channel or

external you want to make a favourite or a

non-favourite TV channel or external.

TV Setup

The Setup menu contains items that control the settings

of the TV’s functions,features,services and peripherals

you may have connected.

The

General

menu allows you to change settings that

will typically be accessed only occasionally.

The

Source

menu allows you to select a source.

The

Decoder

menu allows you to define one or more

programme numbers as decoder programme numbers.

General

Menu background

Factory settings

NEX

IEW

provider

OSD

Programme title

Teletext level 2.5

Auto surround

Set/Change code

Setup

EN 9FTL13E 3.

EN 10 FTL13E3.

Press the cursor right to select

Picture

Select the menu items in the Picture menu with the cursor

up/down.“Adjust the settings with the cursor left/right or enter the list of

submenu items with the cursor right. Select a submenu item

with the cursor up/down.

Note:To remove the menu background before adjusting the picture

settings, see Select TV setup, General, p. 8.

Smart picture

Select

Smart picture

to display a list of predefined picture

settings, each corresponding with specific factory settings.

Personal

refers to the personal preference settings of picture in

the picture menu.

Digital options

Pixel Plus is the most ideal setting, doubles the horizontal

resolution and increases the number of lines with 33%.

You may consider to select Movie Plus in case a halo effect

should disturb you. Dependent on your own preference, select

Progressive scan.

Dynamic contrast

Sets the level at which the TV automatically enhances the details

in dark, middle and light areas of the picture.

DNR

This sets the level at which noise is measured and reduced in

the picture.

Colour enhancement

This makes the colours more vivid and improves the resolution

of details in bright colours.

Hue

This compensates for the colour variations in NTSC encoded

transmissions.

Picture format

This will adjust the size of the picture dependent on the

broadcast format and your preferred setting.

TV menu

Press the

key on the remote control to summon the main menu.

Note: Dependent on the input signal, one or more menu items may not be selectable.

Press the i key on the remote control to get information about the selected menu item.

Picture Sound Features

Smart picture

Contrast

Brightness

Colour

Sharpness

Tint

Digital options

Dynamic contrast

DNR

Colour enhancement

(Hue)

Picture format

Picture menu

Source

This menu allows you to indicate the peripheral

you connected to one of the external inputs.

Press the cursor right to enter the list of types

of peripherals attached to the selected input.

Select the peripheral device with the cursor

up/down.

Once you have selected the source type,e.g. DVD,

this source will automatically be selected when

your remote control is in DVD mode, see p. 3,and

when you press the v key on the remote

control.

Centre input - Centre in volume

When you have connected a surround receiver

to the TV, see p. 18, the loudspeakers of the TV

can act as centre speaker, making a separate

centre speaker unnecessary.

Select

Centre input On

Cinema Link

(in

case you have connected a Cinema Link

Surround receiver).

When having selected

you can adjust the

Centre in volume with the cursor left/right to

correct volume level differences of the external

audio receiver and speakers.

Note:This is not the case with a Cinema Link

surround receiver.

Source

EXT1

EXT2

EXT3

EXT4

YPbPr

FRONT

Centre input

Centre in volume

Setup

If a decoder or a descrambler is connected, see

p. 17, you can define one or more programme

numbers as decoder programme numbers.

Select

Decoder

with the cursor right.

Select

Programme

“

Select the programme number under which

you have stored the programme coming from

your decoder.‘Select

Status

• Select the input used to connect your

decoder:

None

EXT1

EXT2

• Select

None

if you do not want the selected

programme number being activated as a

decoder programme number.

Note: Select

EXT2

when the decoder is connected to

your EasyLink video recorder.

Decoder

Programme

Status

Setup

Demo

The Demo menu allows to demonstrate the TV

features separately or in a continuous loop.

Auto demo

has been selected the demo will

automatically present the features sequentially in a

loop. Press one of the cursor keys to stop the Auto

demo.

If one of the features has been selected, this

particular feature demo will run only once, and the

Demo menu will reappear.

Note:The Dealer demo is not part of the automatic

sequence and can only be activated separately.

Auto demo

......

Dealer demo - Digital options

- Light sensor

- Comb filter

Setup

Demo

Install

Directions for Use

Programme list

Press the

key to switch over to the

selected TV channel or external.

Select subtitles

The subtitle page must be stored for each TV

channel:

Switch on teletext and select the proper

subtitle page from the index. Switch off

teletext.

Subtitle On

will automatically display them on

the selected TV channels if subtitles are in the

transmission.A symbol will indicate that the

mode is on.

Select

On during mute

when you want to

have the subtitles automatically displayed only

when the sound has been muted with the ¬

key on the remote control.

Child lock

Note: A VGA source can not be locked.

Select

Child lock

Press the cursor right to enter the Child lock

menu.You’re summoned to enter your code.

Note:You have to re-enter your code each time you

enter the child lock menu.

Important:You have forgotten your code !

See p. 8.

“

Select one of the menu items of the child lock

menu:

•

Lock

if you want to lock all channels and

externals.

•

Custom lock

and press the cursor right.

Select:

Lock after

if you want to lock all programmes

from a certain time onwards.

Press the cursor right and enter the time with

the cursor up/down and right. Press the

key to validate.

Programme lock

if you want to lock a certain

TV channel or external;

• Select

Unlock

to disable all locks you have set.

On timer

Select

On timer

with the cursor down.

Select

with the cursor right.

“

Press the cursor right again to enter the

programme list.

‘

Select the TV channel or external you want

your TV to switch to on a selected time and

day.(Press the cursor right again to select a day of

the week or to select

Daily

Press the cursor right once again to enter the

time with the digit keys or with the cursor

up/down and press the

key to activate.

Press the

key to turn off the menu.

Note:To check your timer settings, press the i

key.

Zoom

Note: Dependent on the input signal, Zoom may not be

selectable.

Select

Zoom

with the cursor down and press

the ok key.

Press the

key to select one of the zoom

magnifications (x1, x4,x9, x16).

“

Additionally you can shift the selected zoom

window over the screen with the cursor keys

up/down, left/right.‘Press the

key to turn off the zoom

function.

Child lock

Lock

Custom lock

Unlock

Lock after

Programme lock

VCR1

BBC2

CNN

TVE

π.....

Sunday

Monday

.......

Daily

15:45

On timer

Off

The TV continuously measures and corrects all

incoming signals in order to provide the best

picture possible.

Press the h key on the remote control.éThe Active Control menu appears.“Press the cursor up/down to select the Active

Control values

Off

Minimum

Medium

(recommended) or

Maximum

The picture settings are being optimised

continuously and automatically which is

displayed by bars.The menu items can not be

selected.

‘

Press the cursor right to select

Smart

Picture

(

Press the cursor up/down to select one of the

predefined picture settings.

Press the cursor right to select

Active

Display

Press the cursor up/down to select

Show bars

one of the Dual screen demos or

Off

When you select Dynamic contrast, Pixel Plus,

Digital Noise Reduction or Digital Natural

Motion, the TV screen is divided into two parts:

in the left part the selected picture quality

setting is switched off; in the right part it is

switched on.

Note: Dependent on the input signal, one or more

Dual screen demos may not be selectable.

Press the h key again to switch off the Active

Control menu.

Active Control

Press the cursor right to select

Sound

Select the menu items in the Sound menu with the cursor

up/down and adjust the settings with the cursor

left/right.Remember,control settings are at normal mid-range

levels when the bar scale is centred.

Smart sound

Select Smart sound to display a list of predefined sound settings,

each corresponding with specific factory settings of Treble and

Bass.

Personal

refers to the personal preference settings of

sound in the sound menu.

Notes:

- Some menu items are only available in case of a Cinema Link

configuration and when the Cinema Link is activated. Others are

steered by the audio receiver instead of by the TV.See the separate

Cinema Link booklet supplied.

- Dual X is only available with dual sound transmission.

- Mono/Stereo is only selectable in case of analogue stereo

transmission.

- Nicam/Analogue is only selectable in case of Nicam transmission.

Sound

Smart sound

Equalizer

Volume

Balance

Loudness

Headphone volume

Surround mode

(Dual I-II)

(Mono/Stereo)

(Nicam/Analogue)

(3D effect)

AVL

Delta volume

Sound

OffOnOn during mute

Features

Programme list

Subtitle

Sleeptimer

Child lock

On timer

Zoom

Features menu

Press the cursor right to select

Features

Select the menu items with the cursor

up/down and adjust the settings with the

cursor left/right.

Use the on-screen Menu-Info

for more

information about the menu items.

EN 11FTL13E 3.

EN 12 FTL13E3.

1414

Teletext Guide

Enter with the digit keys, the teletext page number that contains the programme information for the

current channel.

Press the cursor right to move the puck over the selection ball.

“

Use the cursor up/down to scroll through the different programmes.

• If the selected programme contains a page number with an optional subcode referring to a page with

more info about the programme, press the

key to display the information.Press the

key again

to return to the programme guide page.

• If the selected programme guide page satisfies the VPT requirements,

- it will be possible to record, remind, watch or lock programmes:

- the TV will remember the last selected teletext page number of that channel that contains programme

guide information and indicates which programme starts at what time. Every time you press the æ

key, the teletext programme guide page of the selected TV channel will be available.

• When necessary you can select the subpage number by moving the cursor to the pageball and

pressing right.

Note:You must enter the teletext pagenumber for each channel.You can change the channels also by moving

the cursor up/down in the list in the left of the page.

Basic functions

Press one of the grey x,red ®, green U, yellow Q or blue Ì keys to activate a

NEX

IEW

Teletext Guide function.The keys appear in grey if the function is not available.

Review

: this menu provides a list of programmes that are marked as reminders, those that have to be

recorded and those that are locked.This menu can be used to change or remove marked

programmes.

Record

: to programme the recording of the video recorder (if it has a

NEX

IEW

Link function and is

connected to

EXT. 2

Remind

: automatically switch on the TV if it is in standby or by displaying a message if the TV is on.

Lock

: to lock certain programmes to prevent recording or watching.

For the functions Record, Remind or Lock, a small menu pops up in which you can choose the

interval: once, daily or weekly, or clear an earlier made record, remind or lock setting.The default

interval is set to

Once

.To confirm the frequency, press the

key.

Watch

: to watch the selected and currently broadcast programme.

Acquisition and updating of

NEX

IEW

information

Acquisition and updating of

NEX

IEW

is done when you are watching the TV channel of the selected

NEX

IEW

provider, see Setup menu, p. 8,or when the TV is switched to standby;

Acquisition of fresh data will happen once during the night.

Note: it may be necessary to put the TV in standby mode when all

NEX

IEW

information is outdated, e.g. when

returning from holiday.

Review Record Remind Watch Lock

BBC1

BBC2

ITV

CH4

CH5

page ball

selection ball

channel list

Mon 05 Feb 16.35

100 1

BBC CEEFAX

LIONS RECORD ANOTHER WIN 430

Index 100 News 300

BBC Info 110 Headlines 305

Children 120 Weather 400

Cookery 150 Sports 415

Education 200 Radio 500

subpages

scroll ball

1313

NEX

IEW

/ Teletext guide

NEX

IEW

is an electronic guide that allows you to look up programmes as you would in a

newspaper or a TV magazine.You can sort the programmes by subject (films, sport...),obtain

detailed information and programme your video recorder if it comes with the

NEX

IEW

Link

function.

Important note: The

NEX

IEW

service is only available on certain programmes and in certain

countries.When no

NEX

IEW

information is broadcast, the teletext programme guide appears in its place.This is

based on teletext programme information (if available) and offers most functions of

NEX

IEW

Note:The broadcaster is responsible for the content of the information.

Call

NEX

IEW

/ Teletext guide

Press the æ key on the remote control to call the

NEX

IEW

/Teletext guide.A menu appears with

the message

One moment please

.After a while you obtain:

•a

NEX

IEW

page, if the selected channel broadcasts this service (the

NEX

IEW

logo is displayed),

• a teletext page, if the selected channel does not broadcast

NEX

IEW

•

No information available

is displayed if neither

NEX

IEW

nor teletext are transmitted. In this case,

select another channel.

Display of a

NEX

IEW

page

The information is set by the channel that transmits the

NEX

IEW

service. See also Setup menu,

General,

NEX

IEW

provider, p. 8.

This logo is only displayed

during a

NEX

IEW

transmission or when one

of the externals is selected.

No logo indicates a teletext

programme guide

Programme name and

broadcast time

Review Record Remind Watch Lock

Mon 03

Tue 04

Wed 05

Thu 06

Fri 07

Sat 08

puck

function keys

NEX

IEW

guides

BBC1 18.00 BBC News

BBC2 18.00 The Simpsons

CNN 18.00 World News

FR2 18.00 On a tout essayé!

CH5 18.15 Tomorrow Never Dies

Menu 18.00 Channel Theme

Mon

Feb

18.00

NEX

IEW

guides

Use the cursor key left/right to select

Time

Channel

Theme

, the

Date

guide.

The

Time guide

provides an overview of all programme titles active in the selected time block.The

Channel guide

provides an overview of all programmes that are broadcast by a single channel during

one day. With the

Date guide

you can choose a specific date.The

Theme guide

displays a list of all

programmes at the selected date, that matches with the selected category.

Going through the menu guide, the TV is collecting the sorting criteria to finally display a list of

programme events.

Press the OK key to select the guide type.“Move the puck down and to the right to select the programmes.

If available a summary or commentary on the programme is displayed at the bottom of the screen.‘Use the cursor up/down to scroll through the programmes.

Directions for Use

1616

Teletext menu

Press the

key to activate the menu.

Press the cursor up/down to select the menu

items.“Press the cursor right to activate.

Reveal

Reveals/conceals hidden information on a page,

such as solutions to riddles and puzzles.

Press the cursor right to activate.

Favourite

This list contains up to eight favourite teletext

pages. Only the pages of the current channel

can be selected.

Press the cursor right to enter the list.

Press the cursor right again to add the current

page or to select one of the favourite pages to

the list.“Press the

key to watch the page.

‘

Use the 0 key to browse through the list of

favourite pages.

Selecting a word

On the keyboard on screen you can type in a

random word you want to search for in the

teletext pages.Whether upper- or lowercase is

used has no influence.

Press the cursor right to enter the keyboard.éPress the cursor left/right, up/down to select

the characters, words or functions.

“

Press the

key to confirm each character

selected.

‘

Select

Cancel

to cancel the word;

Space

enter a space;

Delete

to delete the last

character selected;

Shift

to switch between

lowercase or capital characters;

Special

display special characters on the keyboard and

press the

key.

(

Press the cursor left repeatedly to return to

the Teletext menu again.

Searching a word

Type in the word on screen or select a word

from the history list on the right and press

Select

and press

again.The

message Searching appears.

“

To cancel the searching or to search for a new

word, select

Keyboard

and press

‘

When a word is not found, a message appears.

When the word is found, it is highlighted in the

teletext page.To continue the search,press the

key.

Cycle subpages (if available)

Makes the subpages cycle automatically.

Press the cursor right to activate and to de-

activate again.

Timed page

To display a specific page from a selected TV

channel at a certain time.

Press the cursor right and select

Ye s

Enter the time and pagenumber with the

cursor keys or the digit keys.

Notes:

- Teletext does not have to remain switched on, but

you should watch the TV channel you have

selected the specific page from.

- It is not possible to display a timed page when in

VGA mode.

“

Press the cursor left to return to the TV menu

again.

Language

If the displayed characters on screen do not

correspond with the characters used by the

teletext broadcaster, you can change the

language group here.

Select

Group 1

Group 2

with the cursor

right.

Press the

key to leave the Teletext

menu.

102 03 04 05 06 07 08 09 10 11 12

TELETEXT

BBC1

Red Green Yellow Blue

puck

Cancel Accept

Space Delete

ABCDEFG 1 2 3

HIJKLMN 4 5 6

OP QRSTU 7 8 9

V W X Y Z 0

Shift Special

WORD

NAME

FOOTBALL

1515

Switch Teletext on and off

Press b to switch the teletext on.

Select a Teletext page

- Enter the desired page number with the digit

keys, the cursor keys up/down, left/right or

with the

-P+

key.

- Select the options at the bottom of the screen

with the colour keys.

Previously selected teletext page

(Only possible in case there is no list of favourite

teletext pages available. See p. 17.)

Press the 0 key.

Select the index teletext page

Press the grey colour key † to display the

main index (usually p.100).

Only for T.O.P teletext broadcasts :

Press i. AT.O.P. overview of the teletext

subjects available is displayed.

Select with the cursor up/down, left/right the

desired subject and press the

key.

Not all TV channels broadcast T.O.P. teletext.

Select subpages

When a selected teletext page consists of

different subpages, a list of available subpages

appears on the screen.

Press the cursor left or right to select the next

or previous subpage.

Enlarge a Teletext page

Press q repeatedly to display the upper

teletext part, the lower teletext part and then

to return to the normal teletext page size.

When the teletext page is enlarged, you can

scroll the text, line by line using the cursor

up/down.

Hypertext

With hypertext you can quickly jump to a

pagenumber or search for a specific word

shown on the current teletext page.&Press the

key to highlight the first word or

a number on the page.

Use the cursor up/down, left/right to select any

other word or number you want to search for.“Press the

key to confirm.The search starts.

A message appears at the bottom of the screen

to indicate the searching, or that the word or

page is not found.

‘

Use the cursor up to exit hypertext.

Most TV channels broadcast information via teletext.This TV has a 1200 pages memory that will store

most broadcasted pages and subpages to reduce waiting time. After each programme change, the

memory is refreshed.

Teletext

LIONS RECORD ANOTHER WIN 430

Index 100 News 300

BBC Info 110 Headlines 305

Children 120 Weather 400

Cookery 150 Sports 415

Education 200 Radio 500

Lottery 230 Travel 550

Finance 240 Subtitling 888

Music 280 TV Listings 600

Red Green Yellow Blue

102 «03040506070809101112»

BBC CEEFAX 102 Mon 05 Feb 16.35.22

BBC CEEFAX

EN 13FTL13E 3.

EN 14 FTL13E3.

Multi channel Surround receiver

Connect the audio cable to the multi channel Surround receiver

and to

AUDIO OUT L

and

at the bottom of your TV 1.

If you want the loudspeakers of your TV to act as centre

speaker, also connect an audiocable to the multi channel

Surround receiver and to the

CENTRE IN

at the bottom of

your TV 2.

“

Select

Centre Input On

in the Source menu. See p. 9.

The loudspeakers of the TV will now only produce centre

sound, the loudspeakers connected to the audio receiver will

produce Surround Sound.The volume has to be controlled via

the multi channel Surround receiver.

Note: No sound will be heard when a TV channel or external source is

blocked via the Child lock menu (see p. 12).

S•VIDEO

VIDEO AUDIO

CENTRE IN

OUT

AUDIO

Front connections

Camera or Camcorder

Connect your camera or camcorder as shown.éConnect to

VIDEO

2 and

AUDIO L

3 for mono

equipment. For stereo equipment also connect

AUDIO R

S-VHS quality with an S-VHS camcorder is obtained by

connecting the S-VHS cables with the

S-VIDEO

input 1 and

audio inputs 3.

Do not connect cable 1 and 2 at the same time. This may cause

picture distortion !

Headphone

Insert the plug into the headphone socket L as shown.éPress ¬ on the remote control to switch off the internal

loudspeakers of the TV.

The headphone impedance must be between 8 and 4000 Ohm.The

headphone socket has a 3.5 mm jack.

In the Sound menu select

Headphone volume

to adjust the

headphone volume.

ANTENNA

SERVICE

S•VIDEO

VIDEOAUDIO

S•VHSVH

AUDIO

VID

EO I

VIDEOIN

S•VHS

AUDIO

VIDEO IN

1 2

Press the v key on the remote control repeatedly, or select Source in the Setup menu (see p.9) to

select

EXT1

EXT2

EXT3

EXT4

YPbPr

FRONT

VGA

according to where you connected your

equipment.

Remark : Most equipment (decoder,recorder) carries out the switching itself, when it is switched on.

To select connected equipment

There is a wide range of audio and video equipment that can be connected to your TV.

The following connection diagrams show you how to connect them.

Note:

EXT1

can handle CVBS and RGB;

EXT2

CVBS, Y/C and RGB;

EXT3

and

CVBS;

EXT5

Y-Pb-Br 480p, 576p,

1080i;

VGA IN

can hancle VGA,SVGA, XGA and 480p, 576p, 1080i.

It is preferred to connect peripherals with RGB output to

EXT1

EXT2

as RGB provides a better picture quality.

Note: If your recorder is provided with the EasyLink function,it should be connected to

EXT2

to benefit from the

EasyLink functionality.

Recorder (

VCR

DVD

)

Note: Do not place your recorder too close to the screen as some recorders may be susceptible for signals out of the

display. Keep a minimum distance of 0,5 m to the screen.

EXT 1

ANTENNA

S•VIDEO

VIDEO AUDIO

EXT 2

VCR 1 DECODER

CABLE

ANTENNA

S•VIDEO

VIDEO AUDIO

EXT

CABLE

VCR 1

Connect Peripheral Equipment

Connect the aerial cables 1, 2 and, to obtain the

optimum picture quality, eurocable 3 as shown.

If your recorder does not have a euroconnector, the

only possible connection is via the aerial cable.You will

therefore need to tune in your recorder’s test signal and

assign it programme number 0 or store the test signal

under a programme number between 90 and 99, see

Manual installation, p. 6.

See the handbook of your recorder.

Decoder and Recorder

Connect a eurocable 4 to your decoder and to the

special euroconnector of your recorder. See also the

recorder handbook. See Decoder,p.9. You can also

connect your decoder directly to

EXT1

with a

eurocable.

Other equipment

(satellite receiver, decoder,DVD, games, etc.)

Connect the aerial cables 1, 2 and 3 as shown

(only if your peripheral has TV aerial in-/output).

Connect your equipment with a eurocable 4 or 5 to

one of the euroconnectors

EXT1

to obtain a

better picture quality.

Look for the test signal of your peripheral in the same

way as you do for a recorder.“Make a selection in the Setup, Source menu, p. 9.

S•VIDEO

VIDEO AUDIO

DVD

EXT 5

DVD player

With Component Video Output Connectors

(EXT5/YPbPr

)

Connect the three separate component video cables to

the DVD player’s

(Pb) and

(Pr) jacks and to the

Y, Pb and Pr jacks on the TV.

Connect the audio cable to the DVD player’s

AUDIO L

and

jacks and to the

and

audio

EXT5

jacks on the

TV.

Directions for Use

Recorder or DVD with EasyLink

The recorder (VCR or DVD+RW) or DVD can

be operated with the remote control via the

Recorder

DVD

menu on screen.

Press the

key on the remote control.

Select the

Recorder

DVD

menu with the

cursor up/down.

“

Press the cursor left/right, up/down to select

one of the recorder or DVD functions.

The key ® for recording can be operated in the TV

mode.

If your EasyLink recorder has the system standby

function, when you press the B key for 3 seconds,

both TV and the recorder are switched to standby.

Ò p ‡ π † ® Ï

Rwd Play Stop Play Ffw Rec Eject

Recorder

Ò p ‡ π † Ï

Prev. Play Stop Play Next Eject

DVD

Connect your computer

EXT 2

AUDIO

RECEIVER

EXT 5

EXT 1

EXT 4

EXT 3

CINEMA LINK Y

PrR

AUDIO

FUNCTION

AUDIO

OUT

CENTRE

MAINS

ANTENNA

SERVICE

S•VIDEO

VIDEO

VGA

AUDIO

Connect one end of a VGA cable 1 to the video card

of the computer and the other end to the

VGA

connector at the bottom of the TV.

Fix the connectors firmly with the screws on the plug.

In case of a Multimedia computer,connect the audio

cable 2 to the audio outputs of your Multimedia

computer and to the

AUDIO R

(right) and

left)

inputs

of the side panel.

The

VGA IN

connector allows the following TV and

monitor display modes:

EDTV 640/720 x 480p

720 x 576p

HDTV 1920 x1080i

VGA 640 x 480 60 Hz

SVGA 800 x 600 56 Hz

XGA 1024 x 768 60 Hz

Note:

If possible, use the XGA1024x768@60Hz video mode to

obtain the best image quality for your LCD monitor.

See the separate supplied Cinema Link instruction manual.

Attention: the sound info on screen will not correspond with the actual sound reproduction.

Cinema Link surround receiver

OUT

EN 15FTL13E 3.

MAINS

75 ANTENNA

SERVICE

EXT 4

EXT 3

EXT 1

CINEMA LINK

EXT

YPbPrR

EXT 5

AUDIO

FUNCTION

R OUT

AUDIO

VGA

CENTRE

VCR

ENTRE

LINK

INEM

Recorder

DVD/

VCR

EXT

CENTRE

VCR

MAINS

75 ANTENNA

SERVICE

EXT 4

EXT 3

EXT 1

CINEMA LINK

YPbPrR

EXT 5

AUDIO

FUNCTION

R OUT AUDIO

VGA

Recorder

DVD/

CENTRE OUT

DI A

LINK

CINEMA

EN 16 FTL13E3.

Tips

Care of the screen

Do not rub or strike the screen with anything hard as this may scratch, mar, or

damage the screen permanently.

Unplug the set before cleaning the screen. dust the TV by wiping the screen and

the cabinet with a soft, clean cloth.If the screen requires additional cleaning, use

a clean, damp cloth;do not use liquid cleaners or aerosol cleaners.

Poor Picture • Have you selected the correct TV system in the manual installation menu?

• Is your TV or house aerial located too close to loudspeakers, non-earthed audio

equipment or neon lights, etc.?

• Mountains or high buildings can cause double pictures or ghost images.

Sometimes you can improve the picture quality by changing the direction of the

aerial.

• Is the picture or teletext unrecognisable? Check if you have entered the correct

frequency. See Installation, Manual installation, p. 6.

• Are brightness,sharpness and contrast out of adjustment? Select Factory settings in

the Setup, General menu, p. 8.

No Picture • Are the supplied cables connected properly ? (The aerial cable to the TV, the

other aerial to your recorder, the VGA cables to the display, the power cables.)

• Has the child lock been switched off ?

• Is your PC switched on ?

• Do you see a black screen and the indicator in front of the TV lights up green,

this means that the display mode is not supported. Switch your VGA-source to a

correct mode.

• In case of weak or bad signal,consult your dealer.

Digital distortion The low quality of some digital picture material may be the cause of digital image

distortion. In this case select the Soft setting using the Picture menu,Smart Picture,

without changing the picture settings manually.

No sound • No sound on any channel? Check the volume isn’t at minimum.

• Is the sound interrupted with the mute key

No solution found Switch your TV off and then on again once.Never attempt to repair a defective

for your picture or TV yourself. Check with your dealer or call a TV technician.

sound problem ?

Menu Have you selected the wrong menu? Press the menu key again to exit from the

menu.

NEX

IEW

Orange indicator on front of the TV during standby / No

NEX

IEW

info:

See Acquisition and updating of

NEX

IEW

information, p. 14.

Displayed time is wrong:

The broadcaster on programme number one does not transmit the correct local

date and time. Use Reshuffle in the installation menu to place another broadcaster

on programme number one.

Remote control • Check if the remote control is in the correct mode.

• If your TV no longer responds to the remote control, the batteries may be dead.

• You can still use the

MENU/OK

key and the -/+ keys on top of your TV.

Standby Your TV consumes energy in the standby mode. Energy consumption contributes

to air and water pollution. Power consumption: 2 W.

No stable or not Check if you have selected the correct VGA mode in your PC. See the separate

synchronised VGA instruction manual with the monitor.

picture

Miscellaneous . Ambient temperature: + 5~ + 35°C

. Mains: 50/60 Hz Auto Voltage ranging from 198 V to 264 V

. Power consumption: around 170 W

. Standby consumption: 1 W

. Weight (excl. packaging): 17 kg

. Dimensions (wxhxd): 891x489x110

Tips

Audio- and video equipment keys

Record with your recorder with EasyLink

This system remote control operates the following Philips equipment:TV,VCR,

DVD, SAT (RC5),AMP (+TUNER), CD;

Press the

Select

key to operate any of the equipment indicated in the display.

Another device can be selected by pressing Select repeatedly within 2 seconds.The

led will blink slowly to indicate the device.

Press one of the keys on the remote control to operate the peripheral equipment.

To return to TV mode press Select while the led is blinking.

When no action is taken within 60 seconds, the remote goes back to TV mode.

Note:When the

Select

key is pressed and hold for more than 2 seconds, the RC5/RC6

system select command is transmitted.

Select

VCR DVD SAT AMP CD

123

456

789

‡π

†

Active Control

B to switch to standby

S for pause (

VCR

DVD

CD)

® for record

Ò for rewind (

VCR

);

search down (

DVD

AMP

)

‡ for stop

π for play

† for fast forward (

VCR

);

search up (

DVD/AMP

)

æ to select your choice of subtitle

language (

DVD

);

RDS news/TA (

AMP

);

to shuffle play (

)

b to select a

DVD

title;

RDS display (

AMP

);

info on screen (

)

i display information

to switch the menu on or off

- P +

for chapter, channel, track

selection

0 to 9 digit entry

0 tape index (

VCR

select a DVD chapter,

select a frequency (

AMP

)

U VCR timer

Q surround on/off (

AMP

CD)

cursor up/down

to select the next or the

previous disc (

CD)

cursor left/right

to select the previous or

following track (

)

search up/down (

AMP

)

In TV mode, it is possible to start a direct recording of the programme which is being displayed on the TV

screen. Continue to press the ® record key on the remote control for more than 2 seconds.

Note: Switching programme numbers on your TV does not disturb recording !

When recording a programme from a peripheral connected to

EXT 1

EXT 3, EXT 4,EXT 5

FRONT

, you can

not select another TV programme on the screen.

Attention:

Recording from

EXT 5

will only have black and white pictures !

Additionally the DVD, SAT and CD indicator can be programmed to operate the

DVD-R, SAT (RC6),CD-R instead.

Press the

Select

key repeatedly until no LED is lit.

To program

DVD-R

, press the

key + digit 2.

To program

SAT (RC6)

, press the

key + digit 4.

To program

CD-R

, press the

key + digit 6.

From now on, when the corresponding (

DVD

SAT

) indicator is selected,

the remote control will operate your DVD-R, SAT (RC6) or CD-R.

Note:To return to the modes programmed in the factory, either remove the batteries for a

few minutes, or press the

key + digit 1 (DVD mode);or + digit 3 (SAT-RC5) or +

digit 5 (CD mode).

Directions for Use

Table of TV frequencies.

Frequenztabelle der Fernsehsender.

Liste des fréquences des émetteurs.

Frequentietabel TV-Zenders.

Tabella delle frequenze delle trasmittenti.

Lista de las frecuencias de las emisoras.

Lista das frequências dos emissores.

Liste over TV senderne.

Tabell over TV-frekvenser.

Tabell över TV-frekvenser.

TV-taajuustaulukko.

Kατάλογος συχνοτήτων ποµπών.

Spisok hastot peredathikov.

A televizió−adóállomások frekvenciáinak a listája.

Lista częstotliwości stacji nadawczych.

Seznam frekvenčních pásem vysílačů.

Zoznam frekvenčných pásiem vysielačov.

The frequencies used by a cable company may differ from the

frequencies on the table. Consult your cable company or your

dealer for detailed information.

In Kabelfernsehanlagen können Abweichungen von den in den

Frequenztabellen aufgeführten Frequenzen vorkommen. Bitte

wenden Sie sich an Ihren Fachhändler oder Ihre

Kabelfernsehgesellschaft, die Ihnen die zutreffenden Frequenzen

mitteilt.FLes fréquences utilisées par une société de télédistribution

peuvent être différentes de celles sur la liste des fréquences.

Consultez votre société de télédistribution ou votre revendeur

pour des informations plus détailées.

De frequenties die gebruikt worden door een kabelmaatschappij

kunnen verschillen van deze op de tabel. Raadpleeg uw

kabelexploitant of uw handelaar voor meer informatie.

Le frequenze usate per una società di teledistribuzione possano

essere differenti di quelle nella tabella. Consultate la società di

teledistribuzione o il vostro rivenditore per informazione specifica.

Las frecuencias utilizadas por las empresas de distribución de

señal por cable, pueden ser diferentes de las que se encuentran

en esta tabla. Consulte con su compañia de distribución de

televisión por cable o con su distribuidor para que le proporcionen

una información más detallada.

As frequências utilizadas por uma sociedade de teledistribuição

podem ser diferentes das indicadas na lista de frequências.

Consultar a sociedade de teledistribuição ou o vendedor para

informações mais detalhadas.

Frekvenser benyttet af kabel operatører kan være afvigende fra

disse, kantakt deres kabel operatør eller forhandler for næmere

informa-tion.NFrekvensene som benyttes pa et kabelnett kan avvike fra de

som er oppfört i tabellen. Kontakt ditt kabel-TV selskap eller din

forhandler for næmere opplysninger.SFrekvenserna som används i kabel-TV-näten kan avvika från

frekvenserna i tabellen. Kontakta ditt kabel-TV-bolag eller din

radiohandlare för vidare information.

Kaapeliyhtiöden käyttämät taajuudet voivat poiketa taulukossa

olevista taajuuksista. Tarkat tiedot saat kaapeliyhtiösta tai myyjältä.

Οι συχντητες που χρησιµοποιούνται απ µια εταιρεία τηλεµετάδοσης

είναι δυνατν να είναι διαφορετικές απ αυτές που περιέχει ο κατάλογος.

(Συµβουλευθείτε την εταιρεία τηλεµετάδοσης ή τον πωλητή για

λεπτοµερέστερες πληροφορίες).

CEI

Hastoty na kotoryx peredaòt telakampaniä mogut

otlihatæsä ot hastot na dannoj tablice. (Obratitæsä k

Vaπej telekampanii ili Vaπemu prodavcu za

dopolnitelænoj informaciej.

Egy televizió−adóállomás sugárzáshoz használt frekvenciatar−

tományai lehetnek a táblázatban közöltektől eltérőek is. (Abban

az esetben, ha bővebb információkra van szüksége, forduljon az

eladóhoz.)PLOperator sieci telewizyjnej może stosować inne częstotliwości,

niż te, które figurują na tablicy (bardziej szczegółowych infor−

macji na ten temat zasięgnąć u operatora lub sprzedawcy).

Frekvence používané některými televizními společnostmi se

mohou lišit od údajů uvedených v tomto seznamu. Informujte se

blíže u příslušné společnosti nebo v prodejně, kde jste televizor

koupili.SKFrekvencie používané niektorými spoločnosami televízneho

prenosu sa môžu liši od údajov uvedených v tomto zozname.

Informujte sa bližšie u príslušnej spoločnosti alebo v predajni,

kde ste televízor kúpili.

EUROPE

CH ..FREQ (MHz)

E2.............48.25

E3.............55.25

E4.............62.25

E5...........175.25

E6...........182.25

E7...........189.25

E8...........196.25

E9...........203.25

E10.........210.25

E11.........217.25

E12.........224.25

S1...........105.25

S2...........112.25

S3...........119.25

S4...........126.25

S5...........133.25

S6...........140.25

S7...........147.25

S8...........154.25

S9...........161.25

S10.........168.25

S11.........231.25

S12.........238.25

S13.........245.25

S14.........252.25

S15.........259.25

S16.........266.25

S17.........273.25

S18.........280.25

S19.........287.25

S20.........294.25

H1 ..........303.25

H2 ..........311.25

H3 ..........319.25

H4 ..........327.25

H5 ..........335.25

H6 ..........343.25

H7 ..........351.25

H8 ..........359.25

H9 ..........367.25

H10 ........375.25

H11 ........383.25

H12 ........391.25

H13 ........399.25

H14 ........407.25

H15 ........415.25

H16 ........423.25

H17 ........431.25

H18 ........439.25

H19 ........447.25

21...........471.25

22...........479.25

23...........487.25

24...........495.25

25...........503.25

26...........511.25

27...........519.25

28...........527.25

29...........535.25

30...........543.25

31...........551.25

32...........559.25

33...........567.25

34...........575.25

35...........583.25

36...........591.25

37...........599.25

38...........607.25

39...........615.25

40...........623.25

41...........631.25

42...........639.25

43...........647.25

44...........655.25

45...........663.25

46...........671.25

47...........679.25

48...........687.25

49...........695.25

50...........703.25

51...........711.25

52...........719.25

53...........727.25

54...........735.25

55...........743.25

56...........751.25

57...........759.25

58...........767.25

59...........775.25

60...........783.25

61...........791.25

62...........799.25

63...........807.25

64...........815.25

65...........823.25

66...........831.25

67...........839.25

68...........847.25

69...........855.25

E-EUROPE

CAN..FREQ (MHz)

R1 ..........49.75

R2 ..........59.25

R3 ..........77.25

R4 ..........85.25

R5 ..........93.25

R 6 .......175.25

R 7 .......183.25

R 8 .......191.25

R 9 .......199.25

R10 ......207.25

R11 ......215.25

R12 ......223.25

S1 ........105.25

S2 ........112.25

S3 ........119.25

S4 ........126.25

S5 ........133.25

S6 ........140.25

S7 ........147.25

S8 ........154.25

S9 ........161.25

S10 ......168.25

S11 ......231.25

S12 ......238.25

S13 ......245.25

S14 ......252.25

S15 ......259.25

S16 ......266.25

S17 ......273.25

S18 ......280.25

S19 ......287.25

S20 ......294.25

H1 ........303.25

H2 ........311.25

H3 ........319.25

H4 ........327.25

H5 ........335.25

H6 ........343.25

H7 ........351.25

H8 ........359.25

H9 ........367.25

H10 ......375.25

H11 ......383.25

H12 ......391.25

H13 ......399.25

H14 ......407.25

H15 ......415.25

H16 ......423.25

H17 ......431.25

H18 ......439.25

H19 ......447.25

21.........471.25

22.........479.25

23.........487.25

24.........495.25

25.........503.25

26.........511.25

27.........519.25

28.........527.25

29.........535.25

30.........543.25

31.........551.25

32.........559.25

33.........567.25

34.........575.25

35.........583.25

36.........591.25

37.........599.25

38.........607.25

39.........615.25

40.........623.25

41.........631.25

42.........639.25

43.........647.25

44.........655.25

45.........663.25

46.........671.25

47.........679.25

48.........687.25

49.........695.25

50.........703.25

51.........711.25

52.........719.25

53.........727.25

54.........735.25

55.........743.25

56.........751.25

57.........759.25

58.........767.25

59.........775.25

60.........783.25

61.........791.25

62.........799.25

63.........807.25

64.........815.25

65.........823.25

66.........831.25

67.........839.25

68.........847.25

69.........855.25

FRANCE

CAN..FREQ (MHz)

2..............55.75

3..............60.50

4..............63.75

5..............176.0

6..............184.0

7..............192.0

8..............200.0

9..............208.0

10............216.0

B............116.75

C............128.75

D............140.75

E............159.75

F............164.75

G ...........176.75

H............188.75

I.............200.75

J............212.75

K............224.75

L............236.75

M...........248.75

N ...........260.75

O ...........272.75

P............284.75

Q ...........296.75

H1..........303.25

H2..........311.25

H3..........319.25

H4..........327.25

H5..........335.25

H6..........343.25

H7..........351.25

H8..........359.25

H9..........367.25

H10........375.25

H11........383.25

H12........391.25

H13........399.25

H14........407.25

H15........415.25

H16........423.25

H17........431.25

H18........439.25

H19........447.25

21..........471.25

22..........479.25

23..........487.25

24..........495.25

25..........503.25

26..........511.25

27..........519.25

28..........527.25

29..........535.25

30..........543.25

31..........551.25

32..........559.25

33..........567.25

34..........575.25

35..........583.25

36..........591.25

37..........599.25

38..........607.25

39..........615.25

40..........623.25

41..........631.25

42..........639.25

43..........647.25

44..........655.25

45..........663.25

46..........671.25

47..........679.25

48..........687.25

49..........695.25

50..........703.25

51..........711.25

52..........719.25

53..........727.25

54..........735.25

55..........743.25

56..........751.25

57..........759.25

58..........767.25

59..........775.25

60..........783.25

61..........791.25

62..........799.25

63..........807.25

64..........815.25

65..........823.25

66..........831.25

67..........839.25

68..........847.25

69..........855.25

ITALY

CAN..FREQ (MHz)

A..............53.75

B ..............62.25

C ..............82.25

D............175.25

E ............183.75

F.............192.25

G............201.25

H............210.25

H1..........217.25

S1 ..........105.25

S2 ..........112.25

S3 ..........119.25

S4 ..........126.25

S5 ..........133.25

S6 ..........140.25

S7 ..........147.25

S8 ..........154.25

S9 ..........161.25

S10 ........168.25

S11 ........231.25

S12 ........238.25

S13 ........245.25

S14 ........252.25

S15 ........259.25

S16 ........266.25

S17 ........273.25

S18 ........280.25

S19 ........287.25

S20 ........294.25

H1..........303.25

H2..........311.25

H3..........319.25

H4..........327.25

H5..........335.25

H6..........343.25

H7..........351.25

H8..........359.25

H9..........367.25

H10........375.25

H11........383.25

H12........391.25

H13........399.25

H14........407.25

H15........415.25

H16........423.25

H17........431.25

H18........439.25

H19........447.25

21...........471.25

22...........479.25

23...........487.25

24...........495.25

25...........503.25

26...........511.25

27...........519.25

28...........527.25

29...........535.25

30...........543.25

31...........551.25

32...........559.25

33...........567.25

34...........575.25

35...........583.25

36...........591.25

37...........599.25

38...........607.25

39...........615.25

40...........623.25

41...........631.25

42...........639.25

43...........647.25

44...........655.25

45...........663.25

46...........671.25

47...........679.25

48...........687.25

49...........695.25

50...........703.25

51...........711.25

52...........719.25

53...........727.25

54...........735.25

55...........743.25

56...........751.25

57...........759.25

58...........767.25

59...........775.25

60...........783.25

61...........791.25

62...........799.25

63...........807.25

64...........815.25

65...........823.25

66...........831.25

67...........839.25

68...........847.25

69...........855.25

EN 17FTL13E 3.

Personal Notes:

EN 18 FTL13E4.

Mechanical Instructions

4. Mechanical Instructions

Index of this chapter:

1. Service Positions

2. Assy / PWB Removal

3. Re-assembly

Notes:

• Figures below can deviate slightly from the actual situation, due to the different set executions.

• Follow the disassemble instructions in described order.

4.1 Service Positions

First, put the TV set in its service position. Therefore, place it upside down on a table top (use a protection sheet or a foam cushion).

4.1.1 The Foam Bars

does not take much space, has no risk of over heating, and/or falling. The stands can be mounted and removed quickly and easily with use of the provided screws, which can be tightened and loosened manually without the use of tools

Caution: Only use the screws provided, otherwise it is possible to damage the monitor inside.

4.2 Assy/PWB Removal

4.2.1 Rear Cover

Warning: Disconnect the mains power cord before you remove the rear cover. First, unscrew the rear cover:

1. Remove the screws that secure the rear cover. The screws are located at the top, bottom, left and right side, also there are three deeper located screws next to the stands.

2. Lift the rear cover from the cabinet. Make sure that wires and flat foils are not damaged during cover removal.

4.2.2 Side I/O Panel

CL 36532051_002.eps

Figure 4-1 Foam bars

The foam bars (order code 3122 785 90580) can be used for all types and sizes of Flat TVs. By laying the plasma or LCD TV flat on the (ESD protective) foam bars, a stable situation is created to perform measurements and alignments. By first placing a mirror flat on the table under the TV you can easily see if something is happening on the screen. The stand is also handy to replace the screen.

4.1.2 The Aluminium Stands

190603

Figure 4-3 Side I/O panel

1. Disconnect the cable of the panel

2. To replace the complete bracket, remove the two fixing

screws on either side of the panel.

3. To get the panel out, push the two brackets out and lift the panel off.

4. Remove the panel.

4.2.3 Main switch/LED panel

CL 36532051_001.eps

Figure 4-2 Aluminium stands

The aluminium stands (order code 3122 785 90480) can also be used to do measurements and alignments, also they are very suitable to perform duration tests. With this stands the set

040703

Figure 4-4 Main switch/LED Panel.

Mechanical Instructions

EN 19FTL13E 4.

1. Disconnect the cable on the rear of the panel.

2. Remove the two fixing screws as shown on the photo.

4.2.4 Small Signal Panel

Figure 4-5 Small Signal Panel

1. Disconnect all cables from the panel.

2. Caution: The connectors of the LVDS cable are very

fragile, be careful not to damage them.

3. Remove the fixing screws of the panel.

4.2.6 Auxiliary Supply

Figure 4-7 Auxiliary Supply

1. Disconnect all cables from the panel.

2. Remove the fixing screws of the panel.

4.2.7 Main Power Supply

4.2.5 Audio Amplifier

Figure 4-6 Audio Amplifier

1. Disconnect all cables from the panel.

2. Remove the fixing screws on the panel.

Figure 4-8 Wall mounting bracket

1. Remove the screws on both the top and bottom of the mounting bracket.

2. Remove the bracket before accessing the Main Power Supply panel.

EN 20 FTL13E4.

Mechanical Instructions

Notes:

• As soon as you have removed the plastic back cover, you must replace the speaker-box sealing foam (12nc: 3104 303 10791). This, to ensure that the loudspeakers are airtight. Do not stretch the foam during mounting. Pay special attention to the corners, to make sure that the foam is not stretched and that it is pushed in the corners.

• While re-assembling, make sure that all cables are placed and connected in their original position

Figure 4-9 Main Power Supply

1. Disconnect the cables from the panel.

2. Remove the fixing screws on each side of the panel.

4.2.8 LCD Panel

Figure 4-10 LCD Display

Make sure that the power is switched “off” and that the necessary cables are disconnected. To replace the LCD panel (including the backlight), please remove all the panels first (including the two mounting brackets), as mentioned above.

1. Remove the five fixing screws on the border of the panel with a no. 10 Torx screwdriver.

2. Remove the four fixing screws on the panel with a no. 20 Torx screwdriver.

3. Lift the LCD panel including the backlights out of the frame.

4.3 Set Re-assembly

To re-assemble the whole set, execute all processes in reverse order.

Service Modes, Error Codes, and Fault Finding

5. Service Modes, Error Codes, and Fault Finding

EN 21FTL13E 5.

Index of this chapter:

1. Test points

2. Service Modes

3. Problems and solving tips (related to CSM)

4. ComPair

5. Error Codes

6. The blinking LED procedure

7. Protections

8. Repair tips

9. Software downloading

5.1 Test Points

The chassis is equipped with test points printed on the circuit board assemblies.

Perform measurements under the following conditions:

• Service Default Mode.

• Video: colour bar signal.

• Audio: 3 kHz left, 1 kHz right.

5.2 Service Modes

Service Default Mode (SDM) and Service Alignment Mode (SAM) offer several features for the service technician, while the Customer Service Mode (CSM) is used for communication between a Philips Customer Care Centre (P3C) and a customer.

There is also the option of using ComPair, a hardware interface between a computer (see requirements below) and the TV chassis. It offers the ability of structured troubleshooting, test pattern generation, error code reading, software version readout, and software upgrading. Minimum requirements: a Pentium processor, Windows 95/ 98, and a CD-ROM drive (see also paragraph “ComPair”).

5.2.1 Service Default Mode (SDM)

Purpose

• To create a pre-defined setting, to get the same measurement results as given in this manual.

• To override SW protections.

• To start the blinking LED procedure.

Specifications

• Tuning frequency: 475.25 MHz for PAL/SECAM.

• Colour system: SECAM L for France or PAL B/G for the

rest of Europe.

• All picture settings at 50 % (brightness, colour, contrast).

• All sound settings at 50 %, except volume at 25 %.

• All service-unfriendly modes (if present) are disabled, like: – (Sleep) timer. – Child/parental lock. – Blue mute. – Automatic volume limiter (AVL). – Auto switch-off (when no video signal was received for

10 minutes).

– Skip/blank of non-favourite pre-sets. – Smart modes. – Auto store of personal presets. – Auto user menu time-out.

How to enter SDM

Use one of the following methods:

• Use the standard RC-transmitter and key in the code “062596”, directly followed by the “MENU” button. Note: It is possible that, together with the SDM, the main

menu will appear. To switch it off, push the “MENU” button again.

• Short for a moment the two solder pads (item 9018) on the SSP, with the indication “SDM”. Activation can be performed in all modes, except when the set has a problem with the main microprocessor. Caution: If the SDM is entered via the pins, all the software-controlled protections are de-activated.

• Use the DST-emulation feature of ComPair.

• Use the “DEFAULT” button on the Dealer Service Tool

(RC7150).

After entering this mode, “SDM” will appear in the upper right corner of the screen.

How to navigate

When you press the “MENU” button on the RC transmitter, the set will toggle between the SDM and the normal user menu (with the SDM mode still active in the background).

How to exit SDM

Use one of the following methods:

• Switch the set to STANDBY via the RC-transmitter.

• Press the “EXIT” button on the DST.

• Via a standard customer RC-transmitter: key in “00”-

sequence.

5.2.2 Service Alignment Mode (SAM)

Purpose

• To perform (software) alignments.

• To change option settings.

• To easily identify the used software version.

• To view operation hours.

• To display (or clear) the error code buffer.

Specifications

• Operation hours counter.

• Software version.

• Option settings.

• Error buffer reading and erasing.

• Software alignments.

How to enter SAM

Use one of the following methods:

• Via a standard RC transmitter: key in the code “062596” directly followed by the “OSD [i+]” button. After entering SAM with this method a service warning will appear on the screen, you can continue by pressing any digit key on the RC.

• Short for a moment the two solder pads (item 9017) on the SSP with the indication "SAM". Depending on the software version, it is possible that a service warning will appear. You can continue by pressing any digit key on the RC.

• Use the DST-emulation feature of ComPair.

• Press the ALIGN button on the DST while the set is in the

normal operation

After entering this mode, “SAM” will appear in the upper right corner of the screen.

Contents of SAM:

• OPERATION HOURS. Displays the accumulated total of operation hours (not the standby hours).

• HARDWARE INFO. – ROM VERSION. Displays the date of the software and

the software version of the ROM (example: TL13EU_1.0_01234 = AAAABB_X.Y_NNNNN).

• AAAA= the chassis name.

EN 22 FTL13E5.

Service Modes, Error Codes, and Fault Finding

• BB= the region: EU= Europe, AP= Asia Pacific

PAL/Multi, AN= Asia Pacific NTSC, US= USA, LT= LATAM.

• X.Y= the software version, where X is the main

version number (different numbers are not compatible with one another) and Y is the sub version number (a higher number is always compatible with a lower number).

• NNNNN= last five digits of 12nc code software.

– SW VERSION EPLD. Displays the software version of

the EPLD.

• ERRORS. (followed by maximal 10 errors). The most

recent error is displayed at the upper left (for an error explanation see paragraph “Error Codes”).

• DEFECTIVE MODULE. Here the module that generates

the error is displayed. If there are multiple errors in the buffer, which are not all generated by a single module, there is probably another defect. It will then display the message “UNKNOWN” here.

• RESET ERROR BUFFER. When you press the “OK”

button, the error buffer is reset.

• ALIGNMENTS. This will activate the “ALIGNMENTS” sub-

menu.

• DEALER OPTIONS. Extra features for the dealers.

• SERVICE OPTIONS. Extra features for Service.

• INITIALISE NVM. When an NVM was corrupted (or

replaced) in the former EM3 chassis, the microprocessor replaces the content with default data (to assure that the set can operate). However, all pre-sets and alignment values are gone now, and option numbers are not correct. Therefore, this was a very drastic way. In this chassis, the procedure is implemented in another way: The moment the processor recognises a corrupted NVM, the “initialise NVM” line will be highlighted. Now, you can do two things (dependent of the service instructions at that moment): – Save the content of the NVM via ComPair for

development analysis, before initialising. This will give the Philips Service department an extra possibility for diagnosis (e.g. when Development asks for this).

– Initialise the NVM (same as in the past, however now it

happens conscious).

• STORE. All options and alignments are stored when

pressing the “OK”-button

• FUNCTIONAL TEST. All devices are tested via the “OK”

button. Eventual errors are displayed in the error buffer. The error buffer is not erased, the content returns when this test is terminated.

• DAILY MENUS. With the “OK” button, you can go to the

normal user menu. SAM is still active in the background. With the “MENU” button, you return from the user menu to SAM menu. This feature can be helpful to quickly change some settings in the user menu.

• SW MAINTENANCE.

• UPGRADE. More info see paragraph Software

downloading.

• EVENTS. Not useful for service purposes. In case of

specific software problems, the development department can ask for this info.

• BDM INFO. Broadcast Debug Menu info. The purpose of this menu is to debug the broadcast, not the TV. The menu gives an overview of what is received on the current preset. Following items are displayed:

P r e s e t n r : -- UTC: - - : - - : -- P r e s e t n a m e : ----- LTO: - - : - - : -- Time: - - : - - : -- C N I N V M : ---- Date: - - / - - / ---- C N I F 1 : ---- C N I F 2 : ---- Time TXT: - - : - - : -- C N I V P S : ---- Time 8/30 F1: - - : - - : -- M o r n i n g P r o g : --- Date 8/30 F1: - - / - - / ---- N a m e 8 / 3 0 F 1 : ----- LTO 8/30 F1: - - : - - : -- N a m e 8 / 3 0 F 2 : ----- N a m e T X T : ----- WSS G1: - - - - S i g n a l S t r e n g t h :--- WSS G2: - - - - WSS G3: - - - E P G S e r v i c e : --- WSS G4: - - -

CL 36532017_055.eps

240403

Figure 5-1 Broadcast debug menu overview

Table 5-1 Broadcast debug menu explanation

Item Source Description

Presetnr Set Presetnumber of the current

selected preset.

Presetname Set Presetname of the current se-

lected preset.

CNI NVM Broadcaster CNI number stored in NVM for

the current preset.

CNI F1 Broadcaster CNI number from transmitted

Packet 8/30 Format 1.

CNI F2 Broadcaster CNI number from transmitted

Packet 8/30 Format 2.

CNI VPS Broadcaster CNI number from transmitted

VPS line.

Morning Prog Broadcaster "ARD" or "ZDF" according to

dedicated bit in 8/30 Format 1.

Name 8/30 F1 Broadcaster Name extracted from status

message of 8/30 Format 1.

Name 8/30 F2 Broadcaster Name extracted from status

message of 8/30 Format 2.

Name TXT Broadcaster Name extracted from TXT

header.

Signal Strength

FBX Noise figure measured for se-

lected preset.

EPG Service Set EPG Service stored in NVM for

current preset displayed as "TXT", "MCP", "SCP", "OCP".

UTC Set UTC (Universal Time Code for-

merly known as Greenwich Mean Time) used in the set.

LTO Set LTO (Local Time Offset) used

in the set. Used by EPG for all Nextview displays. (= Time TXT header - Time 8/30 F1 )

Time Set Current time running in the set.

Was extracted at startup, then maintained by software.

Date Set Current date running in the set.

Was extracted at startup, then maintained by software.

Time TXT Broadcaster TXT header time from the se-

lected preset. Time 8/30 F1 Broadcaster UTC time from 8/30 Format 1. Date 8/30 F1 Broadcaster Date from 8/30 Format 1. LTO 8/30 F1 Broadcaster LTO from 8/30 Format 1. WSS G1 Broadcaster WSS Group 1 (Aspect Ratio)

bits 0 1 2 3 WSS G2 Broadcaster WSS Group 2 (Enhanced

Services) bits 4 5 6 7 WSS G3 Broadcaster WSS Group 3 (Subtitles) bits 8

9 10 WSS G4 Broadcaster WSS Group 4 (Reserved) bits

11 12 13

How to navigate

• In SAM, you can select the menu items with the “CURSOR UP/DOWN” key on the RC-transmitter. The selected item will be highlighted. When not all menu items fit on the screen, move the “CURSOR UP/DOWN” key to display the next/previous menu items.

• With the “CURSOR LEFT/RIGHT” keys, it is possible to: – (De) activate the selected menu item. – Change the value of the selected menu item. – Activate the selected submenu.

How to exit SAM

Use one of the following methods:

• Press the “MENU” button on the RC-transmitter, or

Service Modes, Error Codes, and Fault Finding

EN 23FTL13E 5.

• Switch the set to STANDBY via the RC-transmitter, or

• Press the “EXIT” button on the DST.

5.2.3 Customer Service Mode (CSM)

Purpose

When a customer is having problems with his TV-set, he can call his dealer. The service technician can than ask the customer to activate the CSM, in order to identify the status of the set. Now, the service technician can judge the severity of the complaint. In many cases, he can advise the customer how to solve the problem, or he can decide if it is necessary to visit the customer. The CSM is a read only mode; therefore, modifications in this mode are not possible.

How to enter CSM

Use one of the following methods:

• Press the “MUTE” button on the RC-transmitter

simultaneously with the “MENU” button on the TV (top control) for at least 4 seconds.

• Key in the code “123654” via the standard RC transmitter.

Note: Activation of the CSM is only possible if there is no (user) menu on the screen!

How to navigate

By means of the “CURSOR-DOWN/UP” knob on the RCtransmitter, you can navigate through the menus.

Contents of CSM

CUSTOMER SERVICE MENU 1

• SOFTWARE VERSION (example: TL13EU_1.0_01234).

Displays the built-in software version. In case of field problems related to software, software can be upgraded (for more details, see paragraph Software downloading). You will find details of the software versions in the chapter “Software Survey” of the “Product Survey - Colour Television” publication. This publication is generated four times a year.

• SOFTWARE VERSION EPLD. The 12NC-number of the

built-in EPLD software.

• FEATURE BOX. The 12NC-number of the built-in Feature

Box software.

• SET TYPE. This information is very helpful for a helpdesk/

workshop as reference for further diagnosis. In this way, it is not necessary for the customer to look at the rear of the TV-set.

• CODE 1. Gives the latest five errors of the error buffer. As

soon as the built-in diagnose software has detected an error the buffer is adapted. The last occurred error is displayed on the leftmost position. Each error code is displayed as a 3-digit number. When less than 10 errors occur, the rest of the buffer is empty (000). See also paragraph Error Codes for a description.

• CODE 2. Gives the first five errors of the error buffer. See

also paragraph Error Codes for a description.

• VOLUME. Gives the last status of the volume as set by the

customer. The value can vary from 0 (volume is minimum) to 100 (volume is maximum). Volume values can be changed via the volume key on the RC-transmitter.

• BRIGHTNESS. Gives the last status of the brightness as

set by the customer. The value can vary from 0 (brightness is minimum) to 100 (brightness is maximum). Brightness values can be changed via the “CURSOR LEFT” and “CURSOR RIGHT” keys on the RC-transmitter after pressing the “MENU” button and selecting “PICTURE” and “BRIGHTNESS”.

• CONTRAST. Gives the last status of the contrast as set by

the customer. The value can vary from 0 (contrast is minimum) to 100 (contrast is maximum). Contrast values can be changed via “CURSOR LEFT” and “CURSOR RIGHT” keys on the RC-transmitter after pressing the

“MENU” button and selecting “PICTURE” and “CONTRAST”.

CUSTOMER SERVICE MENU 2

• COLOUR. Gives the last status of the colour saturation, as

set by the customer. The value can vary from 0 (colour is minimum) to 100 (colour is maximum). Colour values can be changed via “CURSOR LEFT” and “CURSOR RIGHT” keys on the RC-transmitter after pressing the “MENU” button and selecting “PICTURE” and “COLOUR”.

• HUE. Only relevant for NTSC-signals (e.g. some NTSC-

DVD-discs).

• SHARPNESS. Gives the sharpness value. The value can

vary from 0 (sharpness is minimum) to 7 (sharpness is maximum). In case of bad antenna signals, a too high value of the sharpness can result in a noisy picture. Sharpness values can be changed via the “CURSOR LEFT” and “CURSOR RIGHT” keys on the RC-transmitter after pressing the “MENU” button and selecting “PICTURE” and “SHARPNESS”.

• HEADPHONE VOLUME. Gives the last status of the

headphone volume, as set by the customer. The value can vary from 0 (volume is minimum) to 100 (volume is maximum). Headphone volume values can be changed via the “CURSOR LEFT” and “CURSOR RIGHT” keys on the RC-transmitter after pressing the “MENU” button and selecting “SOUND” and “HEADPHONE VOLUME”.

• SURROUND MODE. Indicates the by the customer

selected surround mode (or automatically chosen mode). Possible values are “OFF”, “INCREDIBLE SURROUND” OR “DOLBY VIRTUAL”. These settings can be influenced after pressing the “MENU” button and selecting “SOUND” and SURROUND MODE”. It can also have been selected automatically by signalling bits (internal software).

• TUNER FREQUENCY. Indicates the frequency the

selected transmitter is tuned to. The tuner frequency can be changed via the “CURSOR LEFT” and “CURSOR RIGHT” keys for fine tune after opening the installation menu and selecting “INSTALL” and “MANUAL INSTALL”.

• DIGITAL OPTION. Gives the selected digital mode,

“PROGRESSIVE SCAN”, “MOVIE PLUS” or “PIXEL PLUS”. Change via “MENU”, “PICTURE”, “DIGITAL OPTIONS”.

• TV SYSTEM. Gives information about the video system of

the selected transmitter.

– BG: PAL BG signal received. – DK: PAL DK signal received. – I: PAL I signal received. – L/La: SECAM L/La signals received. – M: NTSC M signal received with video carrier on 38.9

MHz.

• BALANCE. Indicates the balance settings, between “-50”

and “+50”. Change via “MENU”, “SOUND”, and “BALANCE”. Not applicable for Dolby Pro Logic sets.

CUSTOMER SERVICE MENU 3

• CENTRE MODE. Indicates if centre mode is set “ON” or

“OFF”. When centre mode is on, all TV speakers are used as one centre speaker. Change Centre mode via “MENU”, “SETUP”, “SPEAKERS”, and “CENTRE MODE”.

• DNR. Gives the selected DNR setting (Dynamic Noise

Reduction), “OFF”, “MINIMUM”, “MEDIUM”, or “MAXIMUM”. Change via “MENU”, “PICTURE”, “DNR”

• NOISE FIGURE. Gives the noise ratio for the selected

transmitter. This value can vary from 0 (good signal) to 127 (average signal) and to 255 (bad signal). For some software versions, the noise figure will only be valid when “Active Control” is set to “medium” or “maximum”.

• SOURCE. Indicates which source is used and the video/

audio signal quality of the selected source. (Example: Tuner, Video/NICAM) Source: “TUNER”, “EXT1”, “EXT2”, “EXT3”, “EXT4”, “SIDE”, “AV1”, “AV2”, “AV3” or “AV4”. Video signal quality: “VIDEO”, “S-VIDEO”, “RGB 1FH”, “YPBPR 1FH 480P”, “YPBPR 1FH 576P”, “YPBPR 1FH

EN 24 FTL13E5.

Service Modes, Error Codes, and Fault Finding

1080I”, “YPBPR 2FH 480P”, “YPBPR 2FH 576P”, “YPBPR 2FH 1080I”, “RGB 2FH 480P”, “RGB 2FH 576P” or “RGB 2FH 1080I”. Audio signal quality: “STEREO”, “SPDIF 1”, “SPDIF 2”, or “SPDIF”.

• AUDIO SYSTEM. Gives information about the audio

system of the selected transmitter: “ANALOGUE MONO”, “ANALOGUE STEREO”, “PCM 2/0”, “DD 1/0”, “DD 2/0 LtRt”, “DD 2/0 L0R0”, “DD 2/1”, “DD 2/2”, “DD 3/0”, “DD 3/ 1”, “DD 3/2”, “DD 1+1”, “MPEG 1/0”, “MPEG 2/0”, “MPEG 2/0 LtRt”, “MPEG 2/1”, “MPEG 2/2”, “MPEG 3/0”, “MPEG 3/1”, “MPEG 3/2”, “MPEG 1+1” or “MPEG 2+2”.

• TUNED BIT. Gives information about the tuning method of

the stored pre-set. If a channel is found via “automatic installation”, you will see the value “YES”. When you change this (automatically found) frequency via “fine tune” adjustment (installation menu - manual installation), the displayed value will change to “NO”. Therefore, when you see the value “NO” in this line, it is an indication that the received channel is a non-standard signal (e.g. of a VCR).

• SURROUND SPEAKERS. Not applicable in this set.

• ON TIMER. Indicates if the “On Timer” is set “ON” or “OFF”

and if the timer is “ON” also displays start time, start day and program number. Change via “MENU”, “TV”, “FEATURES”, and “ON TIMER”.

• PRESET LOCK. Indicates if the selected preset has a child

lock: “LOCKED” or “UNLOCKED”. Change via “MENU”, “TV”, “FEATURES”, “CHILD LOCK”, and “CUSTOM LOCK”.

• CHILD LOCK. Indicates the last status of the general child

lock: “UNLOCK”, “LOCK”, or “CUSTOM LOCK”. Change via “MENU”, “TV”, “FEATURES”, “CHILD LOCK”, and “LOCK”.

CUSTOMER SERVICE MENU 4

• AGE LOCK. Indicates the last status of the EPG rating for

child lock: “OFF”, “4 YEARS”, “6 YEARS”, “8 YEARS”, “10 YEARS”, “12 YEARS”, “14 YEARS” or “16 YEARS”. This is only displayed if child lock is set to “CUSTOM LOCK”

• LOCK AFTER. Indicates at what time the child lock is set:

“OFF” or e.g. “18:45” (lock time). This is only displayed if child lock is set to “CUSTOM LOCK”

• CATEGORY LOCK. Indicates the last status of the EPG

theme childlock: “MOVIES”, “NEWS”, “SHOWS”, “SPORTS”, “CHILDREN”, “MUSIC”, “CULTURE”, or “SERIES”. This is only displayed if child lock is set to “CUSTOM LOCK”. It is possible that more than one value is shown.

• PROGRAM CATEGORY. Indicates the theme of the

selected transmitter: “MOVIES”, “NEWS”, “SHOWS”, “SPORTS”, “CHILDREN”, “MUSIC”, “CULTURE”, or “SERIES”.

• TV RATINGS LOCK. Only applicable for US.

• MOVIE RATINGS LOCK. Only applicable for US.

• V-CHIP TV STATUS. Only applicable for US.

• V-CHIP MOVIE STATUS. Only applicable for US.

• OPTIONS 1. Gives the option codes of option group 1 as

set in SAM (Service Alignment Mode).

• OPTIONS 2. Gives the option codes of option group 2 as

set in SAM (Service Alignment Mode).

CUSTOMER SERVICE MENU 5

• AVL. Indicates the last status of AVL (Automatic Volume

Level): “ON” or “OFF”. Change via “MENU”, “TV”, “SOUND”, “AVL”

• DELTA VOLUME. Indicates the last status of the delta

volume for the selected preset as set by the customer: from “-12” to “+12”. Change via “MENU”, “TV”, “SOUND”, “DELTA VOLUME”.

How to exit CSM

Use one of the following methods:

• After you press a key on the RC-transmitter (with exception of the “CHANNEL”, “VOLUME” and digit (0-9) keys), or

• After you switch the TV-set “OFF” with the mains switch.

5.3 Problems and Solving Tips (related to CSM)

Note: Below described problems are all related to the TV

settings (visible in the CSM menu). The procedures to change the value (or status) of the different settings are described above. New value(s) are automatically stored.

5.3.1 Picture Problems

Snowy/noisy picture

1. Check in CSM line NOISE FIGURE. In case the value is "127" or higher, and the value is also high on other programs, check the aerial cable/aerial system. For some software versions, the noise figure will only be valid when “Active Control” is set to “medium” or “maximum”.

2. Check in CSM lines SHARPNESS and NOISE FIGURE. In case the value of line SHARPNESS is "3" or "4" and the value of line NOISE FIGURE is high ("127" or higher), decrease the "Sharpness” value.

Picture too dark

1. Press “Menu”, “TV”, “Picture”, “Smart Picture”. In case the picture improves, increase the “Brightness” or the “Contrast” value. The new value(s) are automatically stored (in “personal” pre-set) for all TV channels.

2. Check in CSM line BRIGHTNESS and CONTRAST. If the value of these lines is low (< "10"), increase the “Brightness” or the “Contrast” value via the user menu.

Picture too bright

1. Press “Menu”, “TV”, “Picture”, “Smart Picture”. In case the picture improves, decrease the “Brightness” or the “Contrast” value. The new value(s) are automatically stored (in “personal” pre-set) for all TV channels.

2. Check in CSM lines BRIGHTNESS and CONTRAST. If the value of these line is high (> 50), decrease the “Brightness” value or increase the “Contrast” value via the user menu.

White line around picture elements and text

1. Press “Menu”, “TV”, “Picture”, “Smart Picture”. In case the picture improves, decrease the “Sharpness” value. The new value is automatically stored (in “personal” pre-set) for all TV channels.

2. Check in CSM line “Sharpness”. If the value is high, decrease it. The new value is automatically stored for all TV channels.

No picture

Check in CSM line TUNED BIT. In case the value is “No”, install the required program again. Open the installation menu and perform manual installation.

No picture

No proper signal is received. Check the aerial cable/aerial system.

No picture or unstable picture

A scrambled or decoded signal is received.

Black and white picture

Check in CSM line COLOUR. In case the value is low (< "10"), increase the “Colour” value via the user menu. The new value is automatically stored for all TV channels.

No colours/colour lines around picture elements or colours not correct or unstable picture

1. Check in CSM line TV SYSTEM. If a “strange” system pops up, something has gone wrong during installation. Reinstall the channel.

2. If in CSM line TV SYSTEM is “L”, the installed system for this pre-set is “France”, while “West Europe” is required. Install the required program again: open the installation

Service Modes, Error Codes, and Fault Finding

EN 25FTL13E 5.

menu and perform manual installation. Select system “West Europe”.

Menu text not sharp enough

1. Press “MENU”, “TV”, “PICTURE”, “SMART PICTURE”. In case picture improves, decrease the contrast value. The new value(s) are automatically stored for all TV channels.

2. Check line 8 “Contrast”. The value of line 8 is high (> 50). Decrease the contrast value.

5.3.2 Sound Problems

No sound from left and right speaker

Check line 6 “Volume”. The value is low. Increase the value of “Volume”. The new value(s) are automatically stored (in “personal” pre-set) for all TV channels.

Sound too loud for left and right speaker

Check line 6 “Volume”. The value is high. Decrease the value of “Volume”. The new value(s) are automatically stored (in “personal” pre-set) for all TV channels.

5.4 ComPair

5.4.1 Introduction

ComPair (Computer Aided Repair) is a service tool for Philips Consumer Electronics products. ComPair is a further development on the European DST (service remote control), which allows faster and more accurate diagnostics. ComPair has three big advantages:

• ComPair helps you to quickly get an understanding on how to repair the chassis in a short time by guiding you systematically through the repair procedures.

• ComPair allows very detailed diagnostics (on I2C level) and is therefore capable of accurately indicating problem areas. You do not have to know anything about I2C commands yourself because ComPair takes care of this.

• ComPair speeds up the repair time since it can automatically communicate with the chassis (when the microprocessor is working) and all repair information is directly available. When ComPair is installed together with the SearchMan electronic manual of the defective chassis, schematics and PWBs are only a mouse click away.

and click on the correct oscillogram you see on the oscilloscope). You can answer by clicking on a link (e.g.

text or a waveform picture) that will bring you to the next step in the faultfinding process.

By a combination of automatic diagnostics and an interactive question / answer procedure, ComPair will enable you to find most problems in a fast and effective way.

Beside fault finding, ComPair provides some additional features like:

• Up- or downloading of pre-sets.

• Managing of pre-set lists.

• Emulation of the Dealer Service Tool (DST).

• If both ComPair and SearchMan (Electronic Service

Manual) are installed, all the schematics and the PWBs of the set are available by clicking on the appropriate hyperlink.

Example: Measure the DC-voltage on capacitor C2568 (Schematic/Panel) at the Mono-carrier.

– Click on the “Panel” hyperlink to automatically show

the PWB with a highlighted capacitor C2568.

– Click on the “Schematic” hyperlink to automatically

show the position of the highlighted capacitor.

5.4.3 Stepwise Start-up

Under normal circumstances, a fault in the power supply, or an error during start-up, will switch the television to protection mode. ComPair can take over the initialisation of the television. In this way, it is possible to distinguish which part of the startup routine (hence which circuitry) is causing the problem. Take notice that the transition between two steps can take some time, so give the set some time to reach a stable state. During the transition time, the LED can blink strangely.

Stepwise start- up explanation

This is realised via ComPair and is very helpful when a protection is activated (see also chapter “Protections”). The following diagram shows the start-up procedure of the set. Every step of the stepwise start-up (also called trapped startup) in the diagram corresponds with the number of times the led blinks.

5.4.2 Specifications

ComPair consists of a Windows based faultfinding program and an interface box between PC and the (defective) product. The ComPair interface box is connected to the PC via a serial or RS232 cable. For this chassis, the ComPair interface box and the TV communicate via a bi-directional service cable via the service connector.

The ComPair faultfinding program is able to determine the problem of the defective television. ComPair can gather diagnostic information in two ways:

• Automatic (by communication with the television): ComPair can automatically read out the contents of the entire error buffer. Diagnosis is done on I2C level. ComPair can access the I2C bus of the television. ComPair can send and receive I2C commands to the micro controller of the television. In this way, it is possible for ComPair to communicate (read and write) to devices on the I2C busses of the TV-set.

• Manually (by asking questions to you): Automatic diagnosis is only possible if the micro controller of the television is working correctly and only to a certain extends. When this is not the case, ComPair will guide you through the faultfinding tree by asking you questions (e.g. Does the

screen give a picture? Click on the correct answer: YES / NO) and showing you examples (e.g. Measure test-point I7

EN 26 FTL13E5.

Service Modes, Error Codes, and Fault Finding

ON/OFF switch to ON

start time extraction

start P50 recording

start EPG loading

stand-by bit = off

Step 1

OFF

OTC gets supply voltage

OTC resets, Initialise IO

pins

Read NVM identification

enable watchdog

Stand-by

Activate MSP reset

Put Stand-by line LOW

Keep sound amplifiers muted with

sound enable = high

+5V and +8V is switched on

t<500ms

t<250ms

+8V and +5V get their nominal

level, detected by the OTC

Activate protection algorithms for +8V and +5V

and I²C (start I²C protection the moment the

component is initialised).

Step 2

Read rest of NVM information

Initialize HIP: IF, source selection, 2fh input, video processing

Switch on the syncoutput: set_syncout_tristate= off

Initialize 3D Combfilter (US

Deactivate reset MSP and

Step 3

only)

Initialize PICNIC

Initialize EPLD

Initialize tuner

Start TXT acquisition

and time extraction

Initialize MSP

Stand-by bit set ?

t<1500ms

t>400ms

yes

Semi stand-by

Figure 5-2 Stepwise start-up diagram.

Switch On LCD

Step 5

CL 36532053_064.eps

100703

Service Modes, Error Codes, and Fault Finding

EN 27FTL13E 5.

Note (*):

• When the set is in stepwise mode and, due to stepping-up, a protection is activated, the set will really go into protection (blinking LED). The set will not leave the stepwise-mode however. If state X is the state where the set went to protection, stepwise start-up will return to state X-1. At state (X-1) diagnostic measurements can be performed. Also, in the short time the set is in state X but not yet in protection, you can also do some measurements.

5.4.4 How To Connect

1. First, install the ComPair Browser software (see the Quick Reference Card for installation instructions).

2. Connect the RS232 interface cable between a free serial (COM) port of your PC and the PC connector (marked with “PC”) of the ComPair interface.

3. Connect the mains adapter to the supply connector (marked with “POWER 9V DC”) of the ComPair interface.

4. Switch the ComPair interface “OFF”.

5. Switch the television set “OFF” with the mains switch.

6. Connect the ComPair interface cable between the

connector on the rear side of the ComPair interface (marked with “I2C”) and the ComPair connector at the rear side of the TV.

7. Plug the mains adapter in a mains outlet, and switch the interface “ON”. The green and red LEDs light up together. The red LED extinguishes after approx. 1 second while the green LED remains lit.

8. Start the ComPair program and read the “Introduction” chapter.

5.5 Error Codes

5.5.1 Introduction

The error code buffer contains all detected errors since the last time the buffer was erased. The buffer is written from left to right, new errors are logged at the left side, and all other errors shift one position to the right. When an error has occurred, the error is added to the list of errors, provided the list is not full or the error is a protection error. When an error occurs and the error buffer is full, then the new error is not added, and the error buffer stays intact (history is maintained), except when the error is a protection error. To prevent that an occasional error stays in the list forever, the error is removed from the list after 50+ operation hours. When multiple errors occur (errors occurred within a short time span), there is a high probability that there is some relation between them.

5.5.2 How to read the Error Buffer

Use one of the following methods:

• On screen via the SAM (only if you have a picture). Examples:

– 0 0 0 0 0: No errors detected – 6 0 0 0 0: Error code 6 is the last and only detected

error

– 9 6 0 0 0: Error code 6 was first detected and error code

9 is the last detected error

• Via the blinking LED procedure (when you have no picture). See next paragraph.

• Via ComPair.

EXTERNAL 2

AUDIO EXTERNAL 1

SERVICE

CONNECTOR

PC VCR I2CPower

9V DC

Figure 5-3 ComPair Unit

5.4.5 How To Order

ComPair order codes (EU/AP/LATAM):

• Starter kit ComPair32/SearchMan32 software and ComPair interface (excl. transformer): 3122 785 90450.

• ComPair interface (excluding transformer): 4822 727

21631.

• Starter kit ComPair32 software (registration version): 3122 785 60040.

• Starter kit SearchMan32 software: 3122 785 60050.

• ComPair32 CD (update): 3122 785 60070 (year 2002,

3122 785 60110 (year 2003).

• SearchMan32 CD (update): 3122 785 60080 (year 2002), 3122 785 60120 (year 2003).

• ComPair interface cable: 3122 785 90004.

• ComPair firmware upgrade IC: 3122 785 90510.

• Transformer Europe: 4822 727 21632.

• Transformer UK: 4822 727 21633.

CL96532156_029.eps

190600

5.5.3 How to clear the Error Buffer

Use one of the following methods:

• By activation of the “RESET ERROR BUFFER” command in the SAM menu.

• With a normal RC, key in sequence “MUTE” followed by “062599” and “OK”.

• When you transmit the commands “DIAGNOSE” - “99” “OK” with ComPair (or with a DST).

• If the content of the error buffer has not changed for 50+ hours, it resets automatically.

5.5.4 Error Codes

In case of non-intermittent faults, clear the error buffer before you begin the repair. This to ensure that old error codes are no longer present. Before clearing the buffer, write down the content, as this history can give you significant information. If possible, check the entire contents of the error buffer. In some situations, an error code is only the result of another error code and not the actual cause (e.g., a fault in the protection detection circuitry can also lead to a protection). There are various errors:

• I2C device errors.

• I2C bus errors.

• Protection errors.

• Errors not related to an I2C device, but of importance: – FALCONIC (ERROR 26): at start-up, after initialisation

of the PICNIC, the presence of the FALCONIC can be checked.

– EAGLE (ERROR 27): at start-up, after initialisation of

the PICNIC, the presence of the Eagle can be checked.

Note: If you encounter any problems, contact your local support desk.

EN 28 FTL13E5.

Table 5-2 Table Errors

Error Device Description Def. item Def. Module indication Diagram

1 M24C32 NVM, spontaneous blinking error 1 7011 Control B5a 3 SAA4978 PICNIC 7713 Feature Box B3a 4 Supply 5 V 5V protection / +5V Supply B5a 5 Supply 8 V 8V protection / +8V Supply B5a 6 Slow I2C bus blocked Spontaneous blinking error 6 / Slow I2C Blocked /

8 TDA932x HIP High-end Input Processor 7323 Chroma IF IO B2 13 UV1318/... Tuner protection 1T01 Tuner B13 14 MSPxxxx ITT sound processor 7A02 Audio module B6a 18 Fast I2C bus blocked Spontaneous blinking error 18 / Fast I2C Blocked / 21 M62320P I/O Expander 7P56 Video Dual Screen B15b 26 SAA4992 Falconic 7718 +3V (FBX) Supply B3b 27 T8F24EF Eagle 7724 +3V (FBX) Supply B3c 32 M29W400BT Flash Ram (EPG) 7012 EPG Memory B5a 53 AD9883A AD converter 2fh input 7L01 HD B19c 55 DC/DC converter One of the voltages is not ok + protection error / Supply / 56 EPLD EPLD error 7V01 Video control B19d,f 83 TEA6422 Source select matrix audio 7I17 Audio Source Select B14d

Service Modes, Error Codes, and Fault Finding

Note:

• Error codes 1, 6, or 18 are protection codes and in this case, supplies of some circuits will be switched “OFF”. Also, in protection, the LED will blink the number of times equivalent to the most recent error code.

5.6 The Blinking LED Procedure

5.6.1 Introduction

Via this procedure, you can make the contents of the error buffer visible via the front LED. This is especially useful for fault finding, when there is no picture.

When the SDM is entered, the front LED will show (blink) the contents of the error-buffer. Error-codes > 10 are shown as follows: – A long blink of 750 ms (which is an indication of the decimal

digit),

– A pause of 1.5 s, – “n” short blinks (where “n” = 1 - 9), – When all the error-codes are displayed, the sequence

finishes with a LED blink of 3 s,

– The sequence starts again.

Example: Error 12 9 6 0 0. After activation of the SDM, the front LED will show: – 1 long blink of 750 ms (which is an indication of the decimal

digit) followed by a pause of 1.5 s,

– 2 short blinks followed by a pause of 3 s, – 9 short blinks followed by a pause of 3 s, – 6 short blinks followed by a pause of 3 s, – 1 long blink of 3 s to finish the sequence, – The sequence starts again.

Note: If errors 1, 6, or 18 occur, the LED always gives the last occurred error even if the set is NOT in service mode.

5.6.2 How to Enter

Use one of the following methods:

• Enter the SDM (only via soldering pads marked “SDM” on SSP). The blinking front LED will show the entire contents of the error buffer (this works in “normal operation” mode and in “protection” mode).

• Transmit the commands “MUTE” - “062500” - “OK” with a normal RC. The complete error buffer is shown. Take notice that it takes some seconds before the blinking LED starts.

• Transmit the commands “MUTE” - “06250x” - “OK” with a normal RC (where “x” is a number between 1 and 5). When x= 1 the last detected error is shown, x= 2 the second last

error, etc.... Take notice that it takes some seconds before

the blinking LED starts.

• “DIAGNOSE X” with the DST (where “x” is a number between 1 and 5). When x= 1 the last detected error is

shown, x= 2 the second last error, etc.... When x = 0 all

errors are shown.

5.7 Protections

5.7.1 Introduction

This chassis has only one microprocessor (OTC), which remains active during Standby. This because power of the microprocessor and the attached memory chip set is coming from the 3V3 supply, which is derived from the 5V Standbycircuitry. Therefore, in both Power-on as in Standby mode, the microprocessor is connected to this power supply.

If a fault situation is detected, an error code will be generated and if necessary, the set is put in protection mode. The protection mode is indicated by the blinking of the front LED at a frequency of 3 Hz (or by a coded blinking in special cases).

The content of the error buffer can be read via the service menu (SAM), the blinking LED procedure or via DST/ComPair.

To get a quick diagnosis, this chassis has three service-modes implemented:

• The Customer Service Mode (CSM).

• The Service Default Mode (SDM). Start-up of the set in a

predefined way.

• The Service Alignment Mode (SAM). In this mode, items of the set can be adjusted via a menu.

You can enter both SDM and SAM modes via the “service pads” on the SSP, via an RC-transmitter (DST or standard RC), or via ComPair. It is not possible to enter the SAM in “standby”; the TV has to be in “normal operation” mode.

The “Protection Diagram” shows the structure of the protection system. See diagram below.

Service Modes, Error Codes, and Fault Finding

5.7.4 Hardware Protection

EN 29FTL13E 5.

TUNER

FAST I2C BUS BLOCKED

SLOW I2C BUS BLOCKED

EPLD

FBX

3D COMB (US)

DC_PROT (from audio)

+8V_CON

+5V_CON

DC/DC

PROTECTION

IRQ-DIGITAL (98)

+8V SENSE (105)

+5V SENSE (106)

I2C

Figure 5-4 Protection diagram.

There are several types of protections:

• I2C related protections.

• OTC related protections (via polling on I/O pins or via

algorithms).

• Hardware protection All protections are explained below.

5.7.2 I2C Related Protections

In normal operation, some registers of the I2C controlled ICs are refreshed every 200 ms. During this sequence, the I2C busses and the I2C ICs are checked. An I2C protection will take place if the SDA and SCL lines are short-circuited to ground, or to each other. An I2C error will also occur, if the power supply of the IC is missing.

DC/DC protection: When a 3V3 supply is short-circuited the DC/DC converter switches off and goes in protection. The FBX, EPLD IC, and 3D comb IC (US only) have no supply voltage and give no acknowledge. In this case, the set should go into protection. An error code is written in the NVM: DC/DC error.

FBX protection: the FBX protection is not available any more. It is replaced by the DC/DC protection.

5.7.3 OTC Related Protections

If a protection is detected at an OTC input, the OTC will start to scan all protection inputs every 200 ms for 5 times. If the protection on one of the inputs is still active after 1 s, the microprocessor will put the set in the protection mode. Before the scanning is started, a so-called “ESD refresh” is carried out. This is done, because the interrupt on one of the inputs is possibly caused either by a flash or by ESD. As a flash or ESD can influence IC settings, the HIP, MSP, 3D Comb (US only) and wireless module (not used in this set) are initialised again, to ensure the normal picture and sound conditions of the set.

8 V and 5 V protections: The microprocessor senses the presence of the 8 V and 5 V (via the “+5V_CON” and “+8V_CON” lines). If one (or both) of these voltages is (are) not present, an error code is stored in the error buffer of the NVM, and the set is put in the protection mode.

Audio DC protection: The OTC senses if the audio module is in protection via IRQ-DIGITAL (pin 98 of OTC). If this is the case, the OTC puts the set in protection.

OTC

CL 36532053_065.eps

100703

Short-circuiting the 3V3 supply from the DC/DC converter will shut down the DC/DC converter. The absence of the 3V3 supply line is also sensed via I2C (see description DC/DC protection above), this is useful if there is something wrong in the detection circuit of the DC/DC converter. There are no hardware protections in this chassis, which switch off the supply.

5.8 Repair tips

5.8.1 3V3 Supply (DC/DC converter)

As mentioned above, the DC/DC converter is switched “off” when something goes wrong (detection of a missing 3V3 supply at one of the devices supplied by the 3V3). Because of this, the set goes to protection (I2C protection). Error code 55 is logged. For further diagnoses, you need to overrule the I2C protection: put the set in Service Default Mode by means of the solder pads on the SSB. The DC/DC converter is still not working because it is switched “off” by the 3V3_FAULT line (schematic B12). Now you have some possibilities:

1. First, measure the impedance over diode 6U06. In normal conditions, you should measure approximately 120 ohm (if possible, verify this with another set). If the impedance is much too low, do not try to start up the converter as mentioned below. Remind that if FET 7U03 is shortcircuited, this will also influence your measurement.

2. Desolder coils 5U05 and 5U06, connect an external 3V3 supply at capacitor 2U23 (current limitation to 500 mA) and a second external 3V3 supply at capacitor 2U31 (current limitation to 800 mA). The normal working current of the 3V3_SIM line is approximately 400 mA and the normal working current for the 3V3_DCDCFBX line is approximately 700 mA. Therefore, if one of the currents exceeds their nominal value you can determine in which circuit the overload is situated. If the set would start up and you have normal picture, there is probably no overload but a problem in the detection circuits.

3. If you do not have two external power supplies, you can do the following: Desolder coils 5U02, 5U03, and 5U04 (you must desolder all three, otherwise the circuit could be damaged), connect an external power supply of 3V3 at the cathode of diode 6U06. Make sure to limit the current of this external supply to approximately 1200 mA. If the supplied current exceeds 1100 mA (approximately normal working current) you can conclude that one of the devices supplied by 3V3 is short-circuited.

4. Another possibility is to force the converter to start up by short-circuiting (and keep short-circuited) resistor 3U25 (B12). Caution: Be aware that this can damage the set. Even if you measure approximately 120 ohm over diode 6U06, there can still be something wrong in the converter itself. By short-circuiting resistor 3U25, the internal protection of the converter is disabled.

5.8.2 ComPair

This chassis does not have an IR transmitting LED (as in MGsets). Therefore, a “Service” (ComPair) connector is implemented at the rear side of the set, which is directly accessible (as in A10-, EM2E-, EM3E and EM5E-sets). In addition to this, there is also a blinking LED procedure to show the contents of the error buffer.

When you use ComPair, you have the possibility to activate a “stepwise start-up” mode. With this mode, you can initiate the start-up sequence step by step. This also means that in certain

EN 30 FTL13E5.

Service Modes, Error Codes, and Fault Finding

steps, some protections are not activated. This is sometimes very convenient during repair.

5.8.3 Protections

Activating SDM via the “service pads” will overrule the processor-controlled protections, but not the hardware protections. This means, that the A/D-input protections (5 and 8 V) and the I2C “not-acknowledging” info of FBX + EPLD + 3D Comb (US) and of the tuner are overruled. Caution: When doing this, the service technician must know what he is doing, as it could lead to damaging the set.

Table 5-3 Repair tips

Phenomenon Possible Cause Repair tip

No picture, LED blinking at 3 Hz.

No picture, LED blinking with code 6-6-6 or 18-18-18.

No picture, LED blinking with code 1-1-1.

No RC-reception. Blue LED does not echo RCcommands.

Picture is not synchronised.

Picture is distorted. Check video-path in Serv-

Picture with horizontal stripes.

No menu, no OSD. Probably a defective uP. Measure test points B61to B64 on diagram B5A. No NextView (EPG). IC7012 defective or not

No Teletext. IC7007 defective or not

Problems caused by EPG (Electronic Program Guide). The TV set "hangs".

NexTView EPG is not functioning only Teletext guide.

Various symptoms, due to missing local supply voltage.

Set is in protection due to various causes. For error codes see error-code list.

No communication on slow I2C- or fast I2C-bus.

No communication on NVM-I2C bus to the uP.

uP circuitry or RC-receiver is defective.

The sync is derived in the HIP.

ice Default Mode.

Pixel Plus processing is malfunctioning

powered.

powered. Problems with NexTView

EPG broadcasts.

EPG version 2C3 is switched off during production.

An interrupted fuse, NFRresistor or connection.

5.8.4 Power Supply

The simplest way to repair the power supply is to check (and replace if necessary) the components that are marked grey on schematic SP1.

5.8.5 AUX Supply

First, determine whether one or more of the secondary diodes (6044, 6021, 6291, 6293) are short-circuited. If this is not the case, check (and replace if necessary) the components that are marked grey on schematic SA.

You have no picture, so:

- Read the error buffer via ComPair (error buffer is accessible when set is in protection, compare-file will guide you to this)

- Read the blinking LED information via standard remote command <mute>06250x<ok>.

- Or you read the error code sequence via standard remote command <mute>062500<ok>. When you have found the error, check the circuitry related to the supply voltage and I2Ccommunication or the circuitry that triggers the protection.

As processor cannot communicate with one of the 2 busses it the standby-led spontaneously starts blinking 6-6-6-etc or 18-18-18-etc... If in the error buffer somewhere is an error 6 or 18, these will have the highest priority starting the mentioned blinking. Measure dependent of the error on the I2C-bus which device is loading the bus. (Use I2C-overview)

As the uP cannot communicate with the NVM I2C bus, it spontaneously starts blinking 1-1-1. Note: when there is no access to the NVM, a lot of picture setting can go wrong.

In case the set does react on a local keyboard operation, you must check the RC-receiver circuitry (diagram LD).

Check crystals in the HIP circuit on bad contacts.

Investigate whether there is an error code present in the error buffer. In case there is one, check the I2C-bus and/or supply lines (see overview supply lines).Measure and check signal path Tuner-HIP-FBX-EPLD.

Check functionality on circuitry (B3a, B3b, and B3c) of PICNIC (7713), FALCONIC (7718, EAGLE (7724) and/or field memories (7714, 7717, 7719, 7722 and 7723. Tip: the whole Pixel Plus chipset (3 ICs + 5 Field Memories) can be diagnosed via ComPair.

Check circuitry around IC7012 on diagram B5A.

Check circuitry around IC7007 on diagram B5A. Check also B61 to B64 around uP on diagram B5A.

To switch from EPG 2C3 to Teletext guide. Press for 4 seconds, simultaneously the Menu button on the TV and digit 0 on the remote. The option settings for NexTView type and Flashram will not change.

To switch from Teletext guide to EPG 2C3. Press for 4 seconds, simultaneously the Menu button on the TV and digit 1 on the remote. The option settings for NexTView type and Flashram will not change.

When no symptom or error code leads you to a specific circuitry, use the supply lines overview (see supply lines overview), for a quick scan of all supply lines.

+ 114 hidden pages

Philips FTL13E Schematic

Specifications and Main Features

Frequently Asked Questions

User Manual

1. Technical Specifications, Connections, and Chassis Overview

1.1 Technical Specifications

1.1.1 Vision

1.1.2 Sound

1.1.3 Miscellaneous

1.2 Connections

1.2.1 Side I/O (Left Bottom Side)

Figure 1-1 Rear connections

Hosiden: SVHS (Input)

Cinch (Input)

Headphone (Output)

1.2.2 Audio receiver (if present)

Audio - In (Cinch)

Audio - Out (Cinch)

Audio - Out (Cinch)

1.2.3 VGA

VGA (Input)

Figure 1-2 VGA connector

Cinch (Input)

1.2.4 SCARTs

Figure 1-3 SCART connector

External 1: RGB/YUV and CVBS - In/Out

External 2: CVBS and SVHS - In/Out (for Recorder)

External 3: CVBS - In

External 4: CVBS - In

Aerial - In

1.3 Chassis Overview

Figure 1-4 PWB location

2. Safety Instructions, Warnings, and Notes

2.1 Safety Instructions

2.2 Warnings

2.3.2 Schematic Notes

2.3 Notes

2.3.1 General

3. Directions for Use

4. Mechanical Instructions

4.1 Service Positions

4.1.1 The Foam Bars

4.2 Assy/PWB Removal

4.2.1 Rear Cover

4.2.2 Side I/O Panel

Figure 4-1 Foam bars

4.1.2 The Aluminium Stands

Figure 4-3 Side I/O panel

4.2.3 Main switch/LED panel

Figure 4-2 Aluminium stands

Figure 4-4 Main switch/LED Panel.

4.2.4 Small Signal Panel

Figure 4-5 Small Signal Panel

4.2.6 Auxiliary Supply

Figure 4-7 Auxiliary Supply

4.2.7 Main Power Supply

4.2.5 Audio Amplifier

Figure 4-6 Audio Amplifier

Figure 4-8 Wall mounting bracket

Figure 4-9 Main Power Supply

4.2.8 LCD Panel

Figure 4-10 LCD Display

4.3 Set Re-assembly

5. Service Modes, Error Codes, and Fault Finding

5.1 Test Points

5.2 Service Modes

5.2.1 Service Default Mode (SDM)

Purpose

Specifications

How to enter SDM

How to navigate

How to exit SDM

5.2.2 Service Alignment Mode (SAM)

Purpose

Specifications

How to enter SAM

Contents of SAM:

Figure 5-1 Broadcast debug menu overview

How to navigate

How to exit SAM