Peugeot 307 2007 Owner Manual

46
Automatic comfort
DUAL ZONE AUTOMATIC AIR CONDITIONING
The driver and his front passenger
can each adjust the temperature to
their requirements.
tions: temperature, air flow, air distri-
2.
adjustment.
3.
adjustment.
Automatic visibility
Air conditioning On/Off.
6.
Air distribution
adjustment.
Air flow adjustment.
8.
Air intake/
Air recirculation.
9.
This cruise control, of the new
generation, is linked with the speed
steady speed programmed by the
driver.
tivated, the vehicle speed must be
greater than 25 mph (40 km/h) with
at least fourth gear engaged for vehi-
cles fitted with a manual gearbox.
gearbox, the lever must be in posi-
tion
sequential mode.
When the cruise control function
enables you to display the distance
After a few seconds or when this
As soon as you reach the chosen
speed, press button
2
or
3
orises the speed and the display indi-
cates (e.g. at 70 mph (110 km/h)):
Selecting the function
Place switch
dicates:
and drive momentarily at a speed
greater than the memorised speed.
The value memorised flashes. When
the accelerator pedal is released, the
vehicle will return to the memorised
speed.
Press button
or the brake or
clutch pedal.
The display indicates (e.g. at 70 mph
* According to country.
CRUISE CONTROL*
When the vehicle becomes
stationary, after switching off the
the system checked.
When changing the memo-
can increase or decrease rapidly.
cruise control cannot prevent the
vehicle from exceeding the pro-
grammed speed.
speed limits, nor can it replace the
on the part of the driver.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned
correctly.
- never fit one mat on top of another.
After cancellation of the cruise con-
trol,
button
4
The display indicates (e.g. at 70 mph
To memorise a speed higher than the
Without using the accelerator:
press button
3
A brief press increases by 1 mph
An extended press increases by
5 mph (5 km/h).
A maintained press increases in
steps of 5 mph (5 km/h).
exceed the memorised speed un-
til the required speed is reached,
press button
or
3
Switching the function off
Place dial
in position
0
to switch
the system off.
Operating fault
function, the memorised speed is
erased, the dashes flash for a few
seconds:
To memorise a speed lower than the
press button
2
A brief press decreases by 1 mph
An extended press decreases by
5 mph (5 km/h).
An extended press decreases by
An extended press decreases by
A maintained press decreases in
steps of 5 mph (5 km/h).
This cruise control has a display on
the instrument panel to indicate the
steady speed programmed by the
driver.
tivated, the vehicle speed must be
greater than 25 mph (40 km/h) with
at least fourth gear engaged for vehi-
cles fitted with a manual gearbox.
gearbox, the lever must be in posi-
tion
or at least second gear must
When the cruise control function is ac-
tivated, pressing this button enables
you to display the distance recorder.
After a few seconds or when this
As soon as you reach the chosen
speed, press button
2
or
3
orises the speed and the display indi-
cates (e.g. at 70 mph (110 km/h)):
Selecting the function
Place switch
ON
The cruise control is not yet active
and no speed has been memo-
and drive momentarily at a speed
greater than the memorised speed.
The value memorised flashes. When
the accelerator pedal is released, the
vehicle will return to the memorised
speed.
Press button
or the brake or
clutch pedal.
The display indicates (e.g. at 70 mph
* According to country.
Instrument panel displayCRUISE CONTROL*
After cancellation of the cruise con-
trol,
button
4
The display indicates (e.g. at 70 mph
When the vehicle is stationary, af-
ter the ignition has been switched
off, the system no longer stores
any speed.
To memorise a speed higher than the
Without using the accelerator:
press button
3
A brief press increases by 1 mph
An extended press increases by
5 mph (5 km/h).
A maintained press increases in
steps of 5 mph (5 km/h).
exceed the memorised speed un-
til the required speed is reached,
press button
or
3
Switching the function off
Place dial
in the
OFF
position to
switch the system off.
Operating fault
function, the memorised speed is
erased, the dashes flash for a few
seconds:
the system checked.
When changing the memo-
can increase or decrease rapidly.
slippery roads or in heavy traffic.
cruise control cannot prevent the
vehicle from exceeding the pro-
grammed speed.
speed limits, nor can it replace the
on the part of the driver.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned
correctly.
- never fit one mat on top of another.
To memorise a speed lower than the
press button
2
A brief press decreases by 1 mph
An extended press decreases by
5 mph (5 km/h).
An extended press decreases by
An extended press decreases by
A maintained press decreases in
steps of 5 mph (5 km/h).
VISUAL AND AUDIBLE REAR PARKING ASSISTANCE
This system consists of four proximity
sensors, located in the rear bumper.
This detects any obstacle (person,
vehicle, tree, gate, etc.) behind the
vehicle. Nevertheless, it cannot de-
tect obstacles located just below the
An object, such as a stake, a road-
works cone or any other similar
object may be detected at the begin-
comes close to it.
this function will be disarmed
automatically when the vehicle is
towing a trailer or when a bicycle car-
attachment or bicycle carrier
the sensors are not covered with
gear is engaged, an audible signal
sors may be dirty.
The proximity information is given by:
- an audible signal, which becomes
- a graphic on the multifunction dis-
which transmit:
- on the right if an obstacle is detect-
ed on the right,
- on the left if an obstacle is detected
on the left,
- on the right and on the left if an ob-
stacle is detected in the centre.
When the distance between the rear
of the vehicle and the obstacle is
continuous and the "Danger" symbol
appears depending on the multifunc-
tion display.
again inactive.
when reverse gear is en-
gaged, the service warning
and a message on the multifunction
display.
Activation/Deactivation
Activation
The system is activated as soon as
This is accompanied by an audible
signal and displaying of the vehi-
cle, depending on the multifunction
display.
The system can be activat-
ed or deactivated from the
figuration menu.
The activation and deacti-
vation of the system are memorised
when the engine is switched off.
Switching the system off
Tilt the handle on the left-hand side
to hold the bonnet
open.
the strut in its
RUNNING OUT OF FUEL (DIESEL)
The repriming pump, the degas
screw and the transparent pipe are
sponding drawing):
OPENING THE BONNET
Bonnet strut
To close
the end of its travel.
- fill the fuel tank with at least five li-
tres of diesel,
- unclip the style cover to access the
- squeeze and release the manual
green connector,
- operate the starter until the engine
starts.
2 litre HDI 16V engine
- fill the fuel tank with at least five li-
tres of diesel,
- unclip the style cover to access the
- unscrew the degas screw,
- squeeze and release the manual
escaping via the degas screw,
- retighten the degas screw,
- operate the starter until the engine
starts.
ELECTRIC MIRRORS
STEERING WHEEL HEIGHT AND DEPTH ADJUSTMENT
ELECTRIC WINDOWS
Press or pull the switch lightly.
The window stops as soon as the
switch is released.
2. Passenger’s electric window.
3. Rear right electric window.
4. Rear left electric window.
switches.
Move control
6
to the right or
justed.
Move control
in all four direc-
tions to adjust.
Return control
6
to the centre
When parking the vehicle, the mir-
6
rearwards or au-
tomatically on locking the vehicle us-
49
When stationary, pull handle
A
to unlock the steering wheel.
Adjust the height and depth of
the steering wheel.
Lock it by pushing handle
fully.
50
Automatic operation:
Press or pull the switch firmly. One
touch completely opens or closes
the window.
65
CHECKING THE LEVELS
There are two marks on
the dipstick:
= maximum
= minimum
Oil change
According to the information given in
the servicing booklet.
Viscosity selection
the manufacturer’s requirements.
the coolant does not need to
When the engine is warm, the tem-
ate with the ignition off.
a particle emission filter, the fan
can operate after the vehicle has
stopped, even when the engine is
cold
after the engine has stopped before
carrying out any work.
top up the level.
Windscreen and headlamp
wash level
with particle emission filter)
accompanied by a message and an
audible signal, this indicates a low
diesel additive level.
This additive must be topped up.
as possible.
* According to engine.
To maintain the reliability of
engines and emission control
systems, the use of additives
The level should always be
above the MIN mark and
close to the MAX mark.
“Changing a bulb - Front lights”).
at ambient temperature. The level
should always be above the MIN.
for your safety, we would ad-
vise that you use products
top up between changes. The
or the dipstick.
schedule.
the manufacturer, which fulfil DOT4
standards.
CHECKS
Where the handbrake travel
duction in the performance
of the system, the hand-
even between services.
Air filter and passenger
sion filter is maintained in accordance
with the manufacturer’s servicing
schedule, by a PEUGEOT dealer.
on the style of driving, in
are used in town, over short
distances.
status of the surfaces of the discs and
drums, contact a PEUGEOT dealer.
and characteristics.
To ensure best perform-
ance from components as important
as the power steering and the brak-
offers quite specific products.
To prevent damage to the electrical
to clean
the engine compartment is strictly
Avoid all prolonged contact of the
very corrosive.
following prolonged operation
of the vehicle at very low speed or at
at the exhaust on acceleration. This
vehicle or on the environment.
drains or onto the ground.
containers provided for this
At the start of winter, have
your battery checked by a
If you drive
them twice as often.
the thickness of the pads,
even between services.
This does not require an oil
change. Have the level checked
facturer’s servicing schedule.
To check the main levels
and certain components, in
accordance with the manu-
facturer’s servicing sched-
servicing booklet which correspond
to your vehicle’s engine.
CHECKS
Where the handbrake travel
duction in the performance
of the system, the hand-
even between services.
Air filter and passenger
sion filter is maintained in accordance
with the manufacturer’s servicing
schedule, by a PEUGEOT dealer.
on the style of driving, in
are used in town, over short
distances.
status of the surfaces of the discs and
drums, contact a PEUGEOT dealer.
and characteristics.
To ensure best perform-
ance from components as important
as the power steering and the brak-
offers quite specific products.
To prevent damage to the electrical
to clean
the engine compartment is strictly
Avoid all prolonged contact of the
very corrosive.
following prolonged operation
of the vehicle at very low speed or at
at the exhaust on acceleration. This
vehicle or on the environment.
drains or onto the ground.
containers provided for this
At the start of winter, have
your battery checked by a
If you drive
them twice as often.
the thickness of the pads,
even between services.
This does not require an oil
change. Have the level checked
facturer’s servicing schedule.
To check the main levels
and certain components, in
accordance with the manu-
facturer’s servicing sched-
servicing booklet which correspond
to your vehicle’s engine.
2
Rapid wipe.
Normal wipe.
Intermittent wipe.
0
AUTO
Automatic wipe or single
wipe.
Windscreen wash-wipe: pull the stalk
towards you.
LIGHTS STALK
Automatic switching on
of the lights.
of the ring forwards)
wards)
wards)
71
Vehicles fitted with a rear fog
Vehicles fitted with front fog
Wash-wipe
The position is indicated on the in-
strument panel by the corresponding
WINDSCREEN WIPERS STALK
Function Selection/Off.
2.
Decreasing of the speed.
3.
Increasing of the speed.
4.
Activation/Deactivation of the
system.
The values must be set with the en-
gine running.
98
CRUISE CONTROL
The cruise control or speed limiter
function appears on the instrument
alternate between the activated func-
tion display and the distance record-
er displays.
SPEED LIMITER
Function Selection/Off.
2.
Storing of a speed/Decreasing
of the stored speed.
3.
Storing of a speed/Increasing of
the stored speed.
Deactivation/Reactivation of the
cruise control.
the vehicle speed must be above ap-
at least fourth gear engaged on the
automatic gearbox).
Special front windscreen wiper
Within one minute of switching off
the ignition, operate the wipers
stalk to position the wiper blades
Lift the wiper arm, then unclip the
Fit the new blade and push back
the arm.
the shortest blade is fitted on
the vehicle’s right-hand windscreen
wiper arm.
To return the windscreen wipers
to their normal position, switch on
the ignition and operate the wiper
stalk.
BATTERY
To charge the battery using a
- Disconnect the battery starting with
the negative (-) terminal,
- Follow the instructions for use giv-
en by the battery charger manufac-
turer,
- Check that the terminals and con-
with sulphate (white or greenish de-
them,
- Reconnect the battery starting with
the negative (-) terminal.
2 minutes after switching off
the ignition.
the engine is running.
disconnecting the terminals.
fore disconnecting the battery. If they
do not operate normally following re-
connection of the battery, they must
tialisation of the electric windows"
and "Sunroof").
After every reconnection of the bat-
tery, switch on the ignition and wait
electronic systems to be initialised. If
slight difficulties are experienced
after this, please contact a PEUGEOT
dealer.
tery, the remote control key and the
section).
one month.
To start the vehicle from
another battery:
terminals of the two batteries,
- Connect one end of the green or
- Connect the other end of the green
or black cable to an earth point on
the broken down vehicle as far as
- Operate the starter, let the engine
- Wait for the engine to return to idle,
then disconnect the cables.
The batteries contain harm-
ful substances such as sul-
cordance with regulations and must
waste.
Take used remote control and vehi-
cle batteries to an approved collec-
tion point.
CHANGING A WINDSCREEN WIPER BLADE
ECONOMY MODE FUNCTION
After the engine has stopped, certain
functions (windscreen wiper, electric
windows, sunroof, courtesy lights,
audio equipment, telephone, dipped
for a combined duration of approxi-
charging the battery.
switching to economy mode mes-
sage appears on the multi-function
display and the active functions are
These functions are reactivated au-
tomatically next time the vehicle is
driven.
functions immediately, the engine
few minutes.
The time available to you will then be
double the duration for which the en-
gine is left running. However, this pe-
thirty minutes.
A flat battery prevents the
engine from starting.
LOAD REDUCTION FUNCTION
When driving, certain functions (air
conditioning, heated rear screen,
tomatic, once the battery charge is
sufficient.
at the risk of discharging the
switched off may be reactivated
if the telephone is be-
Without lifting
You must always use a tow bar.
The removable towing eye is inside
the spare wheel.
the removable towing eye is
Unclip the cover, by pressing the
Screw in the towing eye as far as
with a professional lifting device.
When towing with the engine
switched off, there is no brak-
TOWING YOUR VEHICLE
Unclip the top of the cover using a
coin,
Screw in the towing eye as far as
Special features of the
automatic gearbox
When towing with four wheels on the
ground, the following rules must be
obeyed:
- lever in position
- tow the vehicle at less than 30 mph
tance of 30 miles (50 km).
- do not add oil to the gearbox.
axle and the nose weight approach-
es the maximum permitted without
exceeding it.
towing a trailer on a slope
coolant.
As the fan is electrically controlled,
on the engine speed.
To lower the engine speed, reduce
your speed.
The maximum towing load on a long
slope depends on the gradient and
the outside temperature.
ant temperature.
the vehicle and switch off the engine
as soon as possible.
Tyres:
check the tyre pressures of the
towing vehicle and of the trailer, ob-
serving the recommended pressures.
towing increases the brak-
check the electrical signal-
Side wind:
take into acount the in-
creased sensitivity to side wind.
TOWING A TRAILER, CARAVAN, BOAT, etc.
We recommend the use of original
tested and approved from the design
stage of your vehicle and that the fit-
ting of the towbar is entrusted to a
Your vehicle is primarily designed
for transporting people and luggage
trailer.
and its driver must be particularly
careful.
Air density decreases with altitude,
thus reducing engine performance.
Above 1 000 metres, the maximum
towing load must be reduced by 10 %
and so on for every 1 000 metres of
altitude.
The rear parking assistance function
will be disarmed automatically when
a towbar is fitted.
Saloon:
when fitting transverse roof
for this purpose. To access these,
when fitting transverse roof
and follow the manufacturer’s fitting
on the roof rack, for a load-
40 cm (with the exception
of bicycle carriers):
80 kg
adapt the speed of the vehicle to
the profile of the road to avoid
damaging the roof bars and the
fixings on the roof.
FITTING ROOF BARS
VERY COLD CLIMATE SCREEN*
The very cold climate screen is in-
stalled on the lower part of the front
of snow at the radiator cooling fan.
When the snow has cleared (tem-
very cold climate screen.
Offer up the very cold climate
screen facing the front bumper.
Put it in place by pressing at each
clip.
Insert a screwdriver into the hole
Use the screwdriver as a lever to
* According to country.
ACCESSORIES FOR YOUR 307
A wide range of accessories recom-
They all benefit from PEUGEOT’s
These accessories and parts, having
ability and safety, are all adapted to
your PEUGEOT vehicle.
The product range offered by PEUGEOT
Accessories is structured around
5
categories: PROTECTION - TOURING
-
TECHNOLOGY - STYLING -
or PVC door sills.
seats and child seats, audio/tele-
age, under shelf storage (saloon).
Trailer towbar which must be fitted by
the PEUGEOT network.
The fitting of electrical equip-
are not recommended by
failure of your vehicle’s electronic
system.
You are advised to contact a repre-
sentative of the Marque to be shown
the range of recommended equip-
screenwash, interior and
exterior maintenance and
cleaning products.
anti-theft alarm, window en-
graving, wheel locks, first
aid kit, warning triangle,
safety jacket, stolen vehicle
tracking system, dog guard,
snow chains.
audio systems, audio/tele-
free kit, entertainment
screen kit, CD changer,
speakers, DVD player, con-
seat covers compatible with
side air bags, aluminium
gear lever knob, fog lamps,
door deflectors, spoiler (sa-
wheels, trims, sport exhaust.
* When using a tailgate bicycle car-
the multifunction display configu-
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned
and secured correctly,
- never fit one mat on top of another.
warning triangle and a set of
spare bulbs available in the vehicle.
"PORSCHE TIPTRONIC SYSTEM" AUTOMATIC GEARBOX
Gear lever.
button.
3.
button.
one of the positions.
which corresponds to this position is
shown on the instrument panel dis-
VISUAL AND AUDIBLE REAR PARKING ASSISTANCE
A.
Switching on.
Detection.
Activation/Deactivation.
Activate or deactivate
the system by going to
the multifunction display
configuration menu.
When reverse gear is engaged, you
are guided by an audible signal, and
a graphic depending on the multi-
function display, during the reversing
Park.
Reverse.
Neutral.
Drive.
Manual mode.
S:
Sport programme.
Snow programme.
gears engaged.
* According to model.
Switching on the engine
With the handbrake applied, select
or
With the engine running, in position
or
with your foot on the brake,
or
the vehicle moves off immediately.
95
Coolant temperature indicator.
3.
Low fuel level warning light.
Fuel gauge.
Speedometer.
6.
Service indicator, oil level
cruise control/speed limiter.
Trip recorder zero reset button.
8.
Lighting rheostat button.
9.
Left-hand direction indicator.
Central STOP warning light.
Service warning light.
Handbrake, brake fluid level
and electronic brake force
distribution warning light.
Anti-lock braking system (ABS)
warning light.
Electronic stability control (ESP/
ASR) warning light.
warning light.
Emission control system
warning light.
Air bags warning light.
Passenger air bag disarmed
20.
Dipped beam headlamps
21.
Main beam headlamps indicator
Front fog lamps indicator light.
23.
Rear fog lamp indicator light.
Diesel engine preheating light.
25.
Engine oil pressure warning
26.
Battery charge warning light*.
PETROL/DIESEL INSTRUMENT PANEL DIALS: MANUAL GEARBOX
* According to country.
TECHNICAL DATA
DIMENSIONS (in mm)
estate
saloon 3 and 5 door versions
TECHNICAL DATA
THE IDENTIFICATION FEATURES OF YOUR 307
The label
on the driver’s door pillar,
- the wheel and tyre sizes,
- the brands of tyres* approved by
the manufacturer,
- the tyre pressures,
- the paint colour reference*.
The tyre pressure must be
checked when the tyre is
cold, at least once a month.
fuel consumption.
A. Manufacturer’s plate.
corner of the windscreen
* According to country.
WARNING LIGHTS AND INDICATORS
3.
6.
7.
cruise control/speed limiter.
8.
Trip recorder zero reset button.
9.
and electronic brake force
distribution warning light.
Anti-lock braking system (ABS)
warning light.
warning light.
warning light.
Air bags warning light.
20.
22.
23.
25.
26.
27.
28.
Sport programme indicator light.
29.
Gear lever position indicator.
30.
Snow programme indicator light.
PETROL/DIESEL SPORT INSTRUMENT PANEL DIALS: MANUAL/AUTOMATIC GEARBOX
* According to country.
Coolant temperature indicator.
3.
Low fuel level warning light.
Fuel gauge.
Speedometer.
6.
Service indicator, oil level
cruise control/speed limiter.
Trip recorder zero reset button.
8.
Lighting rheostat button.
9.
Snow programme indicator light.
Sport programme indicator light.
Left-hand direction indicator.
Central STOP warning light.
Service warning light.
Handbrake, brake fluid level
and electronic brake force
distribution warning light.
Anti-lock braking system (ABS)
warning light.
Electronic stability control
warning light.
20.
Emission control system
warning light.
21.
Air bags warning light.
Passenger air bag disarmed
23.
Dipped beam headlamps
24.
Main beam headlamps indicator
25.
Front fog lamps indicator light.
26.
Rear fog lamp indicator light.
Engine oil pressure warning
28.
Battery charge warning light*.
PETROL INSTRUMENT PANEL DIALS: AUTOMATIC GEARBOX
* According to country.
WARNING LIGHTS AND INDICATORS
22
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and
trip distances).
the total and trip distances are
displayed for 30 seconds when the
the driver’s door, as well as on lock-
vated (see corresponding section).
Service indicator
This indicates when the next service
facturer’s servicing schedule.
The point at which the next service
cator zero reset (see corresponding
section). It is determined by two pa-
- the distance travelled,
- the time which has elapsed since
the last service.
the distance remaining before
the next service may be weighted
INSTRUMENT PANEL DISPLAY
a few seconds, then the actual gear
engaged is displayed.
This comes on when the
programme on
the automatic gearbox is se-
This comes on when the
programme on the
automatic gearbox is selected.
Automatic gearbox indicator
This is displayed if a gear is
tor between two positions).
operation
WARNING LIGHTS AND INDICATORS
24
Your PEUGEOT dealer carries out
this operation after each service.
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
Switch on the ignition.
The display begins a countdown.
When the display shows
after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least five
will not be registered.
When the ignition is switched on,
the engine oil level is indicated for
a few seconds, after the service
Oil level correct
Oil level gauge fault
tion of the engine oil
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
accompanied by an
audible signal and
a message on the
oil which could damage the engine.
check using the dipstick, it is essen-
tial that the level is topped up.
There are 2 marks on the
dipstick:
- never exceed level A,
- in position B, top up the
ed to your engine.
A
= max.
= min.
Service indicator zero re-set
25
With the lights on, press the button to
vary the intensity of the lighting of the
the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
Trip recorder zero reset
With the ignition on, press the button
alternate between the distance re-
corder and cruise control or speed
WARNING LIGHTS AND INDICATORS
26
TRIP COMPUTER
Press the button, located at the
end of the
wipers stalk
the various items of trip computer
data in succession.
The trip computer data is the follow-
Press the control for more than
two seconds to reset the distance
travelled, the average consump-
tion and the average speed to
zero.
Zero reset
- the range,
- the current consumption,
- the distance travelled,
- the average consumption,
- the average speed.
27
- the current information
tab with:
- the range,
- the current
consumption,
- the distance
travelled,
Press the button, located at the
end of the
wipers stalk
the various trip computer tabs in
succession:
When the route required is dis-
than two seconds.
- the route
tab with:
- the distance
travelled,
- the average
consumption,
- the average speed,
for the first route.
- the route
tab with:
- the distance
travelled,
- the average
consumption,
- the average speed,
for the second route.
and
are independent
permits, for example, daily
calculations, and route
monthly
calculations.
TRIP COMPUTER
Loading...
+ 76 hidden pages