Pelco CM9700-MPS, CM9770-1024X112, CM9770L1024X128, CM9770L-96X64, CM9770L-96X80 Specsheet

PRODUCT SPECIFICATION

analog systems and controls

CM9770 Series Matrix

MICROPROCESSOR-BASED SWITCHER/CONTROLLER; 2,048 INPUTS; 512 OUTPUTS

Product Features

• Microprocessor-Based, Full Cross-Point Video Matrix

• High-Density Architecture Supports up to 256 Cameras and

32 Monitors in Each Bay

• Control up to 2,048 Cameras and 512 Monitors in a Single Node or

Expand Camera Capacity with a Multi-Node System (up to 24 Nodes)

• Full System Reports From CM9700-MGR Provide System Wiring and

Configuration Details

• Sixteen RS-422 COM Ports (Expandable to 120) and Two RS-232

Full-Duplex Ports Available on the CPU

• System Diagnostic LEDs Displayed on Front Panel

• Flash Technology Eases System Maintenance and Upgrades

• Logical Camera Selection and Priority Level Operation

• Multiplexer and DVR Control Via Keyboard

• Built-in Video Loss Detection

• Windows

• Factory Tested Prepackaged Systems

• ASCII Data Input to Interface Access Control and Other External

• Powerful Macro Programming

®

-Based System Management Software (Windows 2000,

XP) Includes Multilanguage Menus and On-Screen Help

Computer-Based Systems

The 9770 System is a full-featured video matrix switching control
system that allows users to view and control up to 2,048 cameras
and 512 monitors on a single node. Expanded monitor capacity in
the matrix bay allows implementation of larger systems with a
smaller footprint (less hardware) than other matrix systems.

The base configuration for the 9770 System is made up of a central
processing unit (CC1), matrix switching bay(s) (MXBs) with video
input/output modules, and keyboard controllers (KBDs). Optional
components can be added to enhance system capabilities.

Preconfigured, prepackaged systems make installation fast and
simple. The 9770 System features a user-friendly Windows-based
management system, which allows for easy system programming
and maintenance.

Optional Accessories

• “Hot Switch” and Backup CPU Ensure Uninterrupted Operation

• Redundant Power Supplies for Switching Bays

• Coaxitron

• Responds to 5,000 Alarms

• Network Interface Unit Allows Multiple Systems to Share Video and

• DVR Management

®

Translator Allows PTZ Communication Over Standard

Coaxial Cable

Control

All CM9770 Series systems require installation by a Pelco Certified Dealer/
Installer . This spe cific at ion s hee t ma y be us ed for pur pos e of info rma ti on only
and does not constitute approval or certification of receiving party. Proof of
certification must be provided pri or to shipmen t of CM9770 Sys tems contained
herein.

Macros allow activation of events based on schedule or alarm.
Macros may call system-wide sequences (tours); activate preset
positions on properly equipped cameras; and activate external
relays to control auxiliary functions such as locking doors (additional
equipment may be required).

The 9770 System also includes built-in video loss detection and
system diagnostic features, indicated by LEDs on the front panel of
the matrix bay. Flash technology incorporated into the system
design allows for easier system maintenance and upgrades.

Optional DVR management allows DVRs to be controlled directly
from the system keyboards. Suitable DVRs can be monitored for
operational conditions ensuring continuous recording.

International Standards

Organization Registered Firm;

ISO 9001 Quality System

C1555 / REVISED 11-2-10

SYSTEM COMPONENTS/TECHNICAL SPECIFICATIONS

Diagnostic Monitor Output One VGA
I/O Ports Sixteen RS-422 ports (expandable to 32); total

system capability is 120 ports*
Two RS-232 ports
One parallel printer port
One VGA output port
Two PC-AT compatible keyboard ports

CENTRAL PROCESSING UNIT (CC1)

The central processing unit communicates with external devices and accepts
commands from external computers, keyboards, graphical user interfaces
(GUIs), access control systems, casino data systems, programmable logic
controllers (PLCs), and lighting and intercom systems. An internal VGA card is
included for displaying system diagnostics and for programming. RS-422
COM ports are provided for communication with external devices such as
matrix switching bays, pan/tilt or dome receivers, and keyboards.

ELECTRICAL

Input Voltage 120 VAC, 60 Hz or 230 VAC, 50 Hz, autoranging
Power Consumption 57 W

MATRIX SWITCHING BAY

Each bay includes a power supply and mounting baffle and will support
modules for up to 256 camera inputs and 32 monitor outputs. Multiple bays
can be used to expand a single CPU system to a maximum of 2,048 camera
inputs and 512 monitor outputs. An optional backup power supply module
(MPS) can be installed in each bay to provide redundancy.

ELECTRICAL

Input Voltage 100-240 VAC, 50/60 Hz, autoranging
Power Consumption 60 W maximum (fully populated)
Communication Full duplex RS-422 using an RJ-45 connector

VIDEO

Bandwidth 15 MHz
Signal-to-Noise Ratio -70.5 dB
Adjacent Channel Crosstalk -60.9 dB at 3.58 MHz
Differential Gain 0.51%
Differential Phase 0.38 degrees
Line Tilt 0.40%
Field Tilt 0.59%
Switching Time 16 mS
Inputs Card slots support up to 256 inputs per bay
Outputs Two output card slots for supporting 32 outputs

per bay
Video Input Level 0.5 to 2 Vp-p, RS-170 composite video
Impedance 75 ohms terminating (looping versions

available)

GENERAL

Operating Temperature 32° to 120°F (0° to 49°C)
Dimensions 19.50" D x 19.00" W x 7.00" H

Mounting Fits 19-inch EIA-standard rack (4 RUs)
Unit Weight 29.7 lb (13.5 kg)
Shipping Weight 43 lb (19.5 kg)

CERTIFICATIONS

• CE, Class A

• FCC, Class A

• UL/cUL Listed

•C-Tick

V-Sync The Pelco V-Sync signal (sent up the coax

Vertical Drive Input connector available on rear panel
Overall Frequency Response Flat to 8 MHz
Luminance Nonlinearity 20%

GENERAL

Operating Temperature 32° to 122°F (0° to 50°C), non-condensing
Dimensions

Matrix Bay 21.70" D x 19.00" W x 10.50" H

Mounting Baffle** 24.00" D x 19.00" W x 1.75" H

Mounting Fits 19-inch EIA-standard rack (matrix bay:

Unit Weight 33 lb (14.99 kg)

Shipping Weight 44 lb (19.96 kg)

CERTIFICATIONS

• CE, Class A

• FCC, Class A

• UL/cUL Listed

•C-Tick

(49.53 x 48.26 x 17.78 cm)

cable) provides a synchronization pulse which
allows roll-free switching between cameras
within the same matrix bay

(55.10 x 48.26 x 26.67 cm)

(60.96 x 48.26 x 4.45 cm)

6 RUs; mounting baffle: 1RU)

52 lb (23.59 kg), fully populated

62 lb (28.12 kg), fully populated

*The CM9700-CC1 is equipped with 16 RS-422 COM ports; total capacity can be expanded to 32 ports by adding two CM9700-SER serial communication cards (8 ports each).

Total system capability can be expanded to 120 RS-422 COM ports by adding three CM9700-SER-32 port expansion units (32 ports each) to the CC1.

**Included with each MXB unit. Total height of MXB with baffle installed is 12.25 inches (31 cm).

SYSTEM COMPONENTS AND ACCESSORIES

CM9700-VPP FRONT PANEL

MODELS

CONTROLLER

CM9700-CC1 CPU controller. Operates on 120 VAC, 60 Hz or

CM9700-SER Serial communication card (RS-422 SERCOM)

CM9700-SER-32 Port expansion unit; 32 serial communication

MATRIX BAY

CM9770-MXB

CM9700-MPS Matrix bay power supply (spare). 120 VAC,

CM9770-DFC Downframe card and cable assembly; connects

CM9770-VCC Video camera card capable of accepting up to

CM9770-RPC Rear panel video card; provides 32 BNC

CM9770-VMC Video monitor card providing 16 monitor

CM9770-RPM Rear panel monitor card; provides 16 BNCs to

CM9700-VPP Video patch panel; provides 32 BNC inputs for

CM9700-CBL-06FT 16-channel coaxial ribbon cable, 6 feet (1.82 m)
CM9700-CBL-10FT 16-channel coaxial ribbon cable, 10 feet (3.04 m)

230 VAC, 50 Hz. (4 RUs).

provides eight communications ports to
interface peripheral equipment (four maximum
per CPU).

(SERCOM) ports per unit. Up to three units can
be added to a CC1. (Check with Pelco’s System
Applications Department before adding to an
existing CM9700-CC1). Includes interconnect­ing cables and adapters for DB9 and RJ45
connectors. Data interface can be RS-232 or
RS-422. (4 RUs).

Video matrix bay equipped with CM9700-MPS
power supply. 100-240 VAC, 50/60 Hz,
autoranging (6 RUs).

60 Hz or 230 VAC, 50 Hz.

multiple matrix bays for expansion purposes.

32 camera inputs. Also requires a rear panel
card (CM9770-DFC, CM9770-RPC).

connectors used to connect camera inputs to
matrix bay.

outputs; requires CM9770-RPM.

connect monitor outputs to matrix bay; also
interfaces video output signals from video
output card.

bringing video inputs into the system or 32 BNC
connections for looping video out of the system;
includes 16-channel coaxial ribbon cable, 3 feet
(0.91 m).
(3 VPP units = 2 RUs; actual height of each VPP
is 1.07 inches [2.7 cm])

OPTIONAL COMPONENTS

The following components are compatible with the 9770 System:

KEYBOARDS
CM9760 Keyboard Controller

The CM9760 keyboard controller allows the user to control the system. The
keyboard includes a variable speed, vector-solving joystick with zoom control
knob for pan/tilt/zoom (PTZ) and dome control. From the keyboard, the user
can control GPI-activated devices, receivers, camera/monitor switching, and
multiplexer screen functions, and create single/dual patterns, zones, zone
labels, presets and preset recalls. The user can also arm and disarm alarms
as well as implement stand-alone, direct mode operation. Twenty-four
programmable soft keys can be individually labeled allowing logical camera
selection based on the camera’s field of view rather than camera numbers.

CM9760-KBD Full-function desktop variable speed keyboard,

CM9760-KBD-B Full-function desktop variable speed keyboard,

CM9760-KBR Full-function 19-inch EIA rack mount keyboard

A suffix of -US, -UK, -AU, or –EU, designating a region-specific power
cord, is added to the above model numbers when ordering. For example, a
CM9760-KBD-US is a desktop keyboard (white finish) with a power cord
for use in the United States.

KBD200A Keyboard Controller

The KBD200A provides control of camera/monitor switching; reset, pattern,
and sequence operation; local and receiver auxiliary operation; and
multiplexer screen functions. The KBD200A also provides push-button control
of PTZ functions. (A KBDKIT is required for power.)

KBD200A Desktop keyboard with full switching

KBD300A Keyboard Controller

The KBD300A provides control of camera/monitor switching; preset, pattern,
and sequence operation; local and receiver auxiliary operation; and
multiplexer screen functions. The KBD300A also provides joystick control of
PTZ functions. (A KBDKIT is required for power.)

KBD300A Desktop keyboard with full switching

NETWORK INTERFACE UNIT

The CM9700-NW1 network interface unit allows multiple systems to share
video and control.

CM9700-NW1 Network interface unit; network CPU and

white finish; 100-240 VAC, 50/60 Hz.

black finish; 100-240 VAC, 50/60 Hz.

(4 RUs); available in black finish only;
100-240 VAC, 50/60 Hz.

capabilities, plus push-button control of PTZ
functions. 12 VAC or ±12 VDC. (Requires
KBDKIT for power.)

capabilities, plus joystick control of PTZ
functions. 12 VAC or ±12 VDC. (Requires
KBDKIT for power.)

software necessary for joining two or more
independent systems together. (4 RUs).

CM9700-VPP video patch panels can be mounted horizontally into a standard
EIA rack. A cable management bracket is attached to each end of the video
patch panel.

SYSTEM COMPONENTS AND ACCESSORIES

Pelco, the Pelco logo, and other trademar ks associated with Pelco products referred

to in this publication are trademarks of Pelco, Inc. or its affiliates. A ll other

product names and services are the property of t heir respective companies.

Product specifications and availability are subjec t to change without notice.

©Copyright 2010, Pelco, Inc. All rights reserved.

CM9700 CC1

CAMERA 1 CAMERA 257

MONITOR 1

MONITOR 16

MONITOR 17

MONITOR 32

CM9765-MXB

CAMERA 704

CM9765-MXB

CM9765-MXB

CM9765-MXB

CM9765-MXB

CM9765-MXB

MISCELLANEOUS

CM9760-ALM Alarm interface unit; connects directly to each

CM9760-CDU-T Code distribution unit; 16-channel RS-422

CM9760-CXTA Coaxitron

CM9760-DMR Data merger and port expander unit; this unit

CM9760-DMR-X Same as CM9760-DMR except 230 VAC, 50 Hz.
CM9760-HS Hot switch interface unit; changeover unit that

CM9760-MDA Master distribution amplifier; inserts master

CM9760-MDA-X Same as CM9760-MDA except 230 VAC, 50 Hz.
CM9700MDD-EVS Matrix digital decoder (NET5301R optimized for

system; each unit can monitor up to 64 alarms

and up to four units can be connected in a

series from one SERCOM port. (1 RU).

transmit only (two data wires and ground)

distributor. Primarily used for wiring up to

16 pan/tilt/zoom receivers in a “star”

configuration. (1 RU).

®

translator; generates Coaxitron
signals for Pelco Coaxitron receivers; each
translator supports up to 16 receivers. (1 RU).

allows multiple CM9700-CC1 units to control
multiple pan/tilt/zoom cameras and allows
multiple keyboards to communicate through
one CC1 port. (1 RU).

monitors the status of a primary CC1 in a
9770 system: three components, 1 RU each.

time and date from the CM9700-CC1 and a
programmable title of up to 24 characters on
one to sixteen video signals. (3 RUs).

use with matrix) that converts digital video
streams from Endura products into analog
video to be viewed and controlled on a Pelco
CM9700 Series matrix switcher.

CM9760-REL Relay interface unit; connects directly to each

system and provides dry contact switching for
direct or automatic control of peripheral
equipment; each unit provides up to 64 SPST
contact outputs. (1 RU).

CM6800E-48X8 Satellite video matrix switcher. Allows the user

to distribute switching capability around a
facility, reducing the number of coaxial cable
runs to the matrix and allowing monitoring at
the satellite switch location. Supports up to
48 inputs, or up to 96 inputs in a 96x16
configuration. (3 RUs).

®

Multiplexers Genex Series MX4009 (9-channel) and MX4016

Genex

(16-channel) multiplexers. (1 RU).

COMPATIBLE RECEIVERS

Spectra® Series Spectra dome multiple protocol receiver.
ERD97P21-U Pelco P protocol receiver.
LRD41C21-1/-2/-3 Legacy
LRD41C22-1/-2/-3 Same as LRD41C21 Series except variable

®

Esprit

Integrated pan/tilt positioning receiver.

Coaxitron Coaxitron translator allows Coaxitron control of

®

ExSite

RU = Rack Unit. One RU is equivalent to 1.75 inches (4.45 cm) of vertical

space. Identifies number of rack units required to mount component in a
19-inch EIA-standard rack mount.

®

‚ fixed speed receiver with presets.

speed receiver.

PTZ cameras.
Integrated explosionproof positioning system.

Pelco, Inc. Worldwide Headquarters:

3500 Pelco Way, Clovis, California 93612-5699 USA

USA & Canada Tel: [phone] • FAX: [phone]
International Tel: [phone] • FAX: [phone]
www.pelco.com