P-DUKE FDC60-12S05, FDC60-12D3305, FDC60-12D15, FDC60-12D12, FDC60-12D05 Datasheet
...
•60 WATTS OUTPUT POWER
•2:1 WIDE INPUT VOLTAGE RANGE
•DESIGN MEET SAFETY STANDARD
•SIX-SIDED CONTINUOUS SHIELD
•HIGH EFFICIENCY UP TO 90%
•3.94” X 2.76” X 0.75” PACKAGE
•FIXED SWITCHING FREQUENCY
The FDC60 series offer 60 watts of output power from a 3.94 x 2.76 x 0.75 inch package. The FDC60 series have 2:1 wide input voltage of 9-18, 18-36 and 36-75VDC. The FDC60 features 1600VDC of isolation, short-circuit and over-voltage protection, as well as six sided shielding. Designed meets the safety of EN60950 and UL1950. All models are particularly suited to telecommunications, industrial, mobile telecom and test equipment applications.
T E C H N I C A L S P E C I F I C AT I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted
OUTPUT SPECIFICATIONS
Output power |
|
|
60 Watts max |
Voltage accuracy |
Full load and nominal Vin |
|
± 2% |
Voltage adjustability |
|
|
± 10% |
|
|
|
|
Minimum load (Note 1) |
FDC60-XXD3305 3.3V output |
800mA, min |
|
Others |
|
10% of FL |
|
|
|
||
Line regulation |
LL to HL at Full Load |
|
± 0.5% |
|
|
|
|
Load regulation |
10% to 100% FL |
|
± 0.5% |
Cross regulation (Note 2) |
|
± 5% |
|
|
|
|
|
Ripple and noise |
20MHz bandwidth |
1%/p-p of Vout max |
|
|
|
|
|
Temperature coefficient |
|
|
I0.02% / ºC, max |
|
|
||
Transient response recovery time 25% load step change |
500uS |
||
|
|
|
|
Over voltage protection |
3.3V output |
|
3.9V |
5V output |
|
6.2V |
|
Zener diode clamp |
12V output |
|
15V |
|
15V output |
|
18V |
Short circuit protection |
Hiccup, automatics recovery |
||
INPUT SPECIFICATIONS
|
|
12V nominal input |
9 – 18VDC |
|
Input voltage range |
24V nominal input |
18 – 36VDC |
||
|
|
48V nominal input |
36 – 75VDC |
|
Input filter |
|
|
|
Pi type |
|
|
|
|
|
Input surge voltage |
12V input |
|
36VDC |
|
24V input |
|
50VDC |
||
100mS max |
|
|
||
|
48V input |
|
100VDC |
|
|
|
|
||
Input reflected ripple (Note 3) Nominal Vin and full load |
40mAp-p |
|||
|
|
|
||
Start up time |
Nominal Vin and constant resistor load |
25mS typ |
||
|
|
|
|
|
Remote ON/OFF |
|
DC-DC ON |
Open or 3.5V < Vr < 12V |
|
|
|
|||
Remote off input current |
DC-DC OFF |
Short or 0V < Vr < 1.2V |
||
Nominal input |
|
30mA |
||
GENERAL SPECIFICATIONS
Efficiency |
|
See table |
|
|
|
Isolation voltage |
|
1600VDC, min |
|
|
|
Isolation resistance |
|
109ohms, min |
Isolation capacitance |
|
1000pF, max |
|
|
|
Switching frequency |
|
200KHz, typ |
|
|
|
Design meet safety standard |
|
UL1950, EN60950 |
|
|
|
Case material |
|
Nickel-coated copper |
|
|
|
Base material |
|
Non-conductive black plastic |
|
|
|
Potting material |
|
Epoxy (UL94-V0) |
|
|
|
Dimensions |
|
3.94 X 2.76 X 0.75 Inches |
|
(100.2 X 70.0 X 19.0 mm) |
|
|
|
|
Weight |
|
280g (9.86oz) |
|
|
|
MTBF (Note 4) |
|
1.533 x 106 hrs |
ENVIRONMENTAL SPECIFICATIONS |
||
Operating temperature range |
-25ºC ~ +71ºC (with derating) |
|
|
|
|
Maximum case temperature |
|
+95ºC |
|
|
|
Storage temperature range |
|
-25ºC ~ +100ºC |
|
|
|
Thermal impedance |
|
5.2ºC/watt |
|
|
|
Thermal shock |
|
MIL-STD-810D |
|
|
|
Vibration |
10~55Hz, 2G, 30minutes along X,Y and Z |
|
|
|
|
Relative humidity |
|
5% to 95% RH |
|
|
|
EMC CHARACTERISTICS |
|
|
Conducted emissions |
EN55022 |
Level A |
|
|
|
Radiated emissions |
EN55022 |
Level A |
|
|
|
Conducted immunity |
EN61000-4-6 |
Perf. Criteria2 |
|
|
|
Radiated immunity |
EN61000-4-3 |
Perf. Criteria2 |
|
|
|
Surge |
EN61000-4-5 |
Perf. Criteria2 |
|
|
|
Fast transient |
EN61000-4-4 |
Perf. Criteria2 |
|
|
|
ESD |
EN61000-4-2 |
Perf. Criteria2 |
|
|
|
Loading...