![](/html/b2/b230/b23051abd30dad53347a67ee0bfa6501c7ec16f0eff82df3487438321da06100/bg1.png)
Step3
Mount the camera
Step2
Making connections
⇨
⇨
⇨
Step5
Configure the network
settings
⇨
Step4
Adjustment
Step1
Processing the ceiling or
wall
No operation is required in processing the ceiling or wall.
TOP
46 mm {1-13/16 inches}
83.5 mm
{3-5/16 inches}
24.5 mm
{15/16 inches}
6 mm {1/4 inches} wide ×
10 mm {3/8 inches}
length hole
Cable access hole
(The female thread for conduit is compliant
with ANSI NPSM (parallel pipe threads) 3/4
or ISO 228-1 (parallel pipe threads) G3/4.)
4 Screws
(M5, locally
procured)
Center of the adapter
box
Cable access hole
Ĺ
TOP mark (internal)
Adapter box
(Optional accessory)
ø30 mm
{1-3/16 inches}
23 mm {29/32 inches}
ASecure the adapter box to the wall.
Drill pilot holes and a cable hole
(see the illustration to the right
for their dimensions). (Drill pilot
holes only if making connections
through the cable hole from the
side.)
Be sure to face “TOP” inside the
adapter box upward.
Use 4 screws (M5:locally
procured) to directly secure the
adapter box to the wall.
Minimum pull-out strength:
724 N {163 lbf} (per 1 pc.)
To install this product outdoors,
be sure to waterproof the
screws and cable pass holes.
Use the adapter box mounting screw
(M4 × 35 mm {1- 3/8 inches}:accessory) for
installing the camera to temporarily install the
camera mount bracket to the left or right
hinge of the adapter box so that it can be
opened and closed.
Secure the camera mount bracket with
“
⇧
TOP/FRONT” facing upward.
When the wall is on one side or the other,
install the adapter box to the hinge on the
opposite side of the wall.
Secure the camera mount bracket to the
hinge of the adapter box using the following
tightening torque.
Recommended tightening torque:
0.78 N·m {0.58 lbf·ft}
【
Common
】Using a 5 mm {3/16 inches} hex wrench
(locally procured), loosen the TILT lock
screw by about 1 turn until the camera
faces downward and then temporarily
tighten the TILT lock screw.
Determine the position where the camera is to be mounted
on the ceiling or wall and drill a hole for securing the cam-
era and wiring as shown in the illustration to the right.
* Determine the diameter and depth of the hole according to the
size of fi xing screws or anchors (4 M5 screws, locally procured).
46 mm
{1-13/16 inches}
83.5 mm
{3-5/16 inches}
Cable access
hole ø30 mm
35 mm {1-3/8 inches}
{1-3/16 inches}
23 mm
{29/32 inches}
PGQX2092XAavs1016-2027Printed in China
WV-S1531LN
Network Camera
Model No. WV-S1531LTN / WV-S1531LN
WV-S1511LN
Installation Guide
Included Installation Instructions
Before attempting to connect or operate this product, please read these instructions carefully and
save this manual for future use.
Before reading this manual, be sure to read the Important Information(included in the CD-ROM).
For information about how to perform the settings and how to operate the camera, refer to the
Operating Instructions on the provided CD-ROM.
The model number is abbreviated in some descriptions in this manual.
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic System Networks Co., Ltd.
Fukuoka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Panasonic System Networks Co., Ltd. 2016
The model number and serial number of this
product may be found on the surface of the unit.
You should note the model number and serial
number of this unit in the space provided and
retain this book as a permanent record of your
purchase to aid identification in the event of
theft.
Model No.
Serial No.
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables
when connecting to computer or peripheral devices). Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate this
equipment.
For U.S.A.
CAN ICES-3(A)/NMB-3(A)
For Canada
WARNING:
• To prevent injury, this apparatus must be securely attached to the wall/ceiling in accordance with
the installation instructions.
• All work related to the installation of this product
should be made by qualified service personnel
or system installers.
• The installation shall be carried out in accordance with all applicable installation rules.
• The connections should comply with local electrical code.
• Batteries (battery pack or batteries installed)
shall not be exposed to excessive heat such as
sunlight, fire or the like.
CAUTION:
• Any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
• The network camera is only intended for a connection to an ethernet or PoE network without
routing to the outside plant.
Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them
to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment.
For more information about collection and recycling, please contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
Note for the battery symbol (bottom symbol)
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
: Direct current symbol
Important safety instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5)
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
6)
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
7) Only use attachments/accessories specified by the manufacturer.
8) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
9) Unplug this apparatus during lightning storms or when unused for long periods of time.
10) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
Troubleshooting
Open Source Software
This product contains open source software licensed under GPL (GNU General Public License),
LGPL (GNU Lesser General Public License), etc.
Customers can duplicate, distribute and modify the source code of the software under license of
GPL and/or LGPL.
Refer to the “readme.txt” file on the provided CD-ROM for further information about open source
software licenses and the source code.
Please note that Panasonic shall not respond to any inquiries regarding the contents of the source
code.
Before requesting service, refer to the Important Information (included in the CD-ROM) and
“Troubleshooting” in the Operating Instructions (included in the CD-ROM) and confirm the
trouble.
Waterproof tape
The following notations are used when describing the functions limited for specified models.
The functions without the notations are supported by all models.
:The functions with this notation are available when using the model WV-S1531LTN / WV-S1531LN.
:The functions with this notation are available when using the model WV-S1511LN.
About the user manuals
Product documentation is composed of the following documents.
• Installation Guide (this document): Explains installation, mounting, cable connections, and adjusting the
fi eld of view. This manual uses the WV-S1511LN as an example in the explanations.
• Important Information (included in the CD-ROM):
Provides basic information about the product.
• Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to
operate this camera.
Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.
When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the Adobe web site
and install it.
The external appearance and other parts shown in this manual may differ from the actual product within the
scope that will not interfere with normal use due to improvement of the product.
About notations
Standard accessories
Installation Guide (this document) ........................1 set
IMPORTANT SAFETY INSTRUCTIONS ............... 1 pc.
Warranty card*1 ...................................................1 set
CD-ROM*2 .......................................................... 1 pc.
Code label*3........................................................ 1 pc.
*1 This product comes with several types of warranties. Each warranty is only applicable to the products pur-
chased in the regions indicated on the relevant warranty.
*2 The CD-ROM contains the operating instructions and different kinds of tool software programs.
*3 This label may be required for network management. Use caution not to lose this label.
The following parts are used during installation procedures.
Camera mount bracket cover ............................. 2 pc.
Camera mount bracket cover fixing screw
(M3 x 6 mm {1/4 inches}) ..................................3 pcs.
(of them, 1 for spare)
Waterproof tape .................................................. 1 pc.
RJ45 waterproof connector cover ...................... 1 pc.
RJ45 waterproof connector cap ......................... 1 pc.
4P alarm cable ................................................... 1 pc.
2P power cable .................................................. 1 pc.
Safety wire ......................................................... 1 pc.
Wire lug fixing screw with a spring washer
M3 x 10 mm {3/8 inches} .................................2 pcs.
(of them, 1 for spare)
Safety wire lug .................................................... 1 pc.
Adapter box ....................................................... 1 pc.
Mounting screws for adapter box
(M5 × 20 mm {13/16 inches}) ...........................5 pcs.
(of them, 1 for spare)
Adapter box mounting screw
(M4 × 35 mm {1- 3/8 inches}) ............................ 1 pc.
Auxiliary handle .................................. 1 pc.
Auxiliary handle
Tear off the blue tape attached on camera arm before installing the camera.
Prepare the required parts for each installation method before starting the installation. The following
are the requirements for the various installation methods.
Preparations
Other items that are needed (not included)
Installation method
Recommended
screw
Description
of installation
method
Directly mount the camera onto the ceiling or wall
(when there is a space for wiring in the ceiling or the wall)
M5 screws/ 4pcs.
【Type 1】
Mount the camera to a junction box
* Only use metal junction boxes.
M4 screws/ 4pcs.
*2
【Type 2】
Mount the camera onto the ceiling or wall using the adapter
box (approx. 510
g
{1.13 lbs})
(when there is no space for wiring in the ceiling or the wall)
M5 screws/ 4pcs.
【Type 3】
*1 To mount the camera onto the ceiling or wall, the safety wire (accessory) must be attached.
Have an M6 bolt and nut or anchor (with the minimum pull-out strength of 724 N {163 lbf})
ready for securing the safety wire.
*2
Prepare a M4 screw with a washer with a diameter of 7.5 mm {5/16 inches} to 10 mm
{3/8inches} and a spring washer.
IMPORTANT:
For the screws or anchor bolts used in the above methods (【Type 1】 to 【Type 3】), be sure
to secure the minimum pull-out strength of 724 N {163 lbf} per screw or bolt.
Select screws according to the material of the location that the camera will be mounted to.
In this case, wood screws and nails should not be used.
If the mounting location such as plaster board is too weak to support the total weight, the
area shall be sufficiently reinforced.
Preparations
【1】
Attaching the safety wire.
A Pass the safety wire (accessory)
through the wire mounting hole in
the safety wire lug (accessory).
Safety wire
(accessory)
Wire fitting
Wire mounting hole
Safety wire lug (accessory)
B Fit the Safety wire lug to the camera.
Recommended tightening torque: 0.59 N·m {0.44 lbf·ft}
* The safety wire is not shown in the subsequent
illustrations.
Wire lug fixing screw with a spring washer (accessory)
(M3 x 10 mm {3/8 inches})
Safety wire lug (accessory)
【2】
Remove the front cover.
Loosen the four front cover fixing screws and
remove the front cover.
IMPORTANT:
Because the front cover is temporarily removed
when installing or adjusting the camera, make
sure no liquid enters the camera at these times.
Front cover
4 Front cover
fixing screws
Installation
The installation tasks are explained using 5 steps.
Remove the camera using the reverse order of the installation procedures.
Step 1 Processing the ceiling or wall *There are 3 methods to install the camera to a ceiling or wall.
⇧
TOP/FRONT mark
TILT lock screw
Camera
mount
bracket
【
Type 1
】
Directly mount the camera onto the ceiling or
wall.
Note:
When installing on a wall, drill a cable access hole
closer to the top side.
When installing on a ceiling, drill a cable access hole
so that it comes to closer to the direction in which
the camera is pointed.
When running the cable using the side cable access
hole of the camera, the "cable access hole" indicated in the right figure is not required. (For the side
cable access hole of the camera, see the figure of
B
in 【Type 1】 of "Step3 Mount the camera".)
46 mm
Cable access hole
ø30 mm
{1-3/16 inches}
83.5 mm
{3-5/16 inches}
35 mm {1-3/8 inches}
{1-13/16 inches}
<Ceiling>
Direction in which the
camera is pointed
⇐
【
Type 2
】
Mount the camera to a junction box.
Note:
When junction boxes or the like are used, it is recommended that 2 pieces be used side by
side. (Securing the camera to one junction box and making connections to the other makes
cable connections easy.)
【
Type 3
】
Mount the camera onto the ceiling or wall using the Adapter box (accessory)
* The following explains an example of mounting the camera on a wall.
BTemporarily secure the camera mount bracket and camera to the adapter box.
Adapter box mounting screw (accessory)
M4 × 35 mm {1- 3/8 inches}
hinges
Adapter box
(accessory)
Camera mount
bracket
⇧
TOP/FRONT
mark
IMPORTANT:
Be sure to install the camera at least 2 m 80 cm {9.2 feet}
from the floor (the distance between the lowest part of the
installed camera and the floor).
WV-S1531LN
S3125A
![](/html/b2/b230/b23051abd30dad53347a67ee0bfa6501c7ec16f0eff82df3487438321da06100/bg2.png)
【1】Change the direction the camera is facing from directly down to facing up
and temporarily fi x the camera in place.
【2】Fit a pin cable (locally procured) to the
MONITOR OUT jack on the camera
and connect an adjustment monitor.
【3】 Insert an SD memory card into the
SD memory card slot, if necessary.
Refer to the "Important Information" on the
provided CD-ROM for how to insert/remove
the SD memory card.
【4】Turn on the camera.
【5】Adjust the angle of the camera.
A
Using a 5 mm {3/16 inches} hex wrench (locally
procured), loosen the PAN lock screw on the
base of camera arm. To direct the camera to the
left, turn the camera arm part clockwise when
viewed from the front. To direct the camera to the
right, turn it counterclockwise.
(Panning range: ±180 °)
BUsing a 5 mm {3/16 inches} hex wrench (locally
procured), loosen the TILT lock screw in the middle of camera arm and roughly adjust the direction of the camera. (Tilting range: 0 ° to 100 °)
CTemporarily tighten PAN lock screw and TILT lock
screw to prevent the camera from moving.
DUsing a 5 mm {3/16 inches} hex wrench (locally
procured), loosen the YAW lock screw and rotate
the camera to adjust the tilt of the camera.
(Yawing range: -190 ° to +100 °)
TILT rotation part
PAN rotation part
Camera arm part
YAW rotation par t
【6】Adjust the zoom and focus.
AAs shown in the left figure, open the zoom cover and insert the auxiliary handle (accessory) into
the zoom knob. Then, loosen the knob by rotating the handle to the left, and move the handle
between TELE and WIDE to obtain the desired field of view.
Then, lock the zoom knob by rotat-
ing it back to the right. Remove the auxiliary handle and close the zoom cover.
A
Adjust the viewing angle by pressing the WIDE
or TELE buttons as shown in the right fi gure.
B
Adjust the focus by pressing the auto focus (AF) button.
Adjust the camera angle and field of view by repeating
steps 【5】 through 【6】. When the desired angle and
field of view are achieved, fix each part by tightening
the corresponding lock screw.
Recommended tightening torque
:
PAN lock screw: 2.7 N·m {2.0 lbf·ft}
TILT lock screw: 9.0 N·m {6.6 lbf·ft}
YAW lock screw: 2.7 N·m {2.0 lbf·ft}
【7】Fix each part by tightening the
corresponding lock screw.
Zoom knob
【8】Remove a pin cable.
【9】Mount the front cover to the camera, and
then fasten it with the 4 fi xing screws.
Recommended tightening torque: 0.59 N·m {0.44 lbf·ft}
*As shown in the right figure, fasten the front cover fi x-
ing screws along the diagonal direction.
【10】Secure the safety wire (accessory) to
the ceiling or wall.
【11】Remove the Protection cover.
When the camera has been installed, remove the protection
cover from the front cover. After removal, be sure not to touch
the clear part of the front cover.
46 mm
83.5 mm
B
Using 2 camera mount bracket cover
fixing screws (M3 x 6 mm {1/4 inches}:
accessory), secure the Camera mount
bracket covers (accessory) to the
Camera mount bracket.
Recommended tightening torque:
0.59 N·m {0.44 lbf ft}
C
Using the camera mount bracket cover
fixing screws (M3×6 mm{1/4 inches}:
accessory), install the camera mount
bracket cover (accessory) with the camera facing downward.
Recommended tightening torque:
0.59 N·m {0.44 lbf ft}
BLoosen the PAN lock screw about 1 turn until the
camera faces upward and use the 2 lower screws
(M5:locally procured) to secure the camera.
* 2 upper screws (M5), Minimum pull-out
strength: 724 N {163 lbf} (per 1 pc.). Secure
the camera through the holes in side B of the
camera mount bracket.
A
Use the 2 upper screws (M5:locally procured) to secure the camera.
TELE button
WIDE button
Auto focus
button (AF)
Step5 Configure the network settings
Configure the setting of the camera after temporarily invalidating the firewall software. Once the
camera configuration is completed, return to the original state.
Contact the network administrator or your Internet service provider for information about configuring
the settings of the network.
【2】Click the [Run] button next to [IP Setting Software].
⇒
[Panasonic IP Setting] screen will be displayed.
The MAC Address / IP address of the detected camera will be displayed.
【1】Insert the provided CD-ROM into theCD-ROM drive of your PC.
The License Agreement will be displayed. Read the Agreement and choose “I accept the term in
the license agreement”, and click [OK].
⇒The launcher window will be displayed.
Note:
If the launcher window is not displayed,
double click the “CDLauncher.exe” file
on the CD-ROM.
Refer to “Using the CD-ROM” in the
Operating Instructions on the provided
CD-ROM for further information about
CDLauncher
Note:
For more information on the following content, refer to the Operating Instructions.
Please set [Time & date] on the [Basic] screen of “Setup” before using the camera.
It is impossible to display H.265 (or H.264) or MJPEG images, receive/transmit audio, display
logs, and use full-screen display when the viewer software “Network Camera View 4S” is not
installed on the PC.
Depending on the environment of your PC, it may take time for images to be displayed.
At the time of purchase, the audio input and output connectors are set to “Off”.If needed,
change the setting on the “Audio” screen in “Setup”.
Due to security enhancements in “IP Setting Software”, “Network settings” cannot be
changed when around 20 minutes have passed after turning on the power of the camera to
be configured. (When the effective period is set to “20 min” in the “Easy IP Setup
accommodate period”.) However, settings can be changed after 20 minutes for cameras in
the initial set mode.
Defocus may be caused by the reinstalled front cover. In this case, perform the auto focus
function from the setup menu.
If images are not displayed, set the Web browser to compatibility view. For details on how to
configure, refer to our website (http://security.panasonic.com/support/info/)
【3】Select the camera you want to configure (A), and click [Network Settings]
(B) to change the network settings. Then, click [Access Camera] (C).
Note:
Select the camera with same MAC address as the MAC address printed on the camera that you
want to configure.
A
B
【4】When the administrator registration window is displayed, enter “User
name”,“Password” and “Retype password” by following the instructions
displayed on the screen, and then click the [Set] button.
IMPORTANT:
When the camera is used over the Internet, setting user authentication to “Off” may lead
to unintended access by a third party. Please leave user authentication set to “On”.
【5】When live images from the camera are displayed, the network connection
is complete.
Please keep your user name and password in a safe place free from public view to ensure
security. After completing the registration, the camera will automatically be re-connected and
the authentication window will be displayed. Enter the registered user name and password.
The default setting of user
authentication is “On”. For
further information, refer
to the “Preface” section in
the Operating
Instructions.
The camera body is waterproof, but the cable ends, inside the adapter box (accessory) are not
waterproof. Apply waterproof treatment on the connecting part as shown below.
【6】
Adequate waterproof treatment is required for the cables when installing the
camera with cables exposed.
Apply some waterproof tape (accessory) as shown
in the right.
<Waterproof treatment for other cables than the Ethernet cable>
Step2 Making connections
■
Refer to the Important Information on the provided CD-ROM
for details about each cable.
*Make sure to use the
stereo mini plug.
【4
】
Audio input cable* (white)
【5
】
Audio output cable* (black)
12 V DC (red)
GND (black)
【2】
12 V DC power
supply terminal
【2】2P power
cable (accessory)
【3
】
4P alarm cable
(accessory)
【3
】
Alarm input/output cable
Ethernet cable (category 5e or better, straight)
【1
】
RJ45 (female) Network cable
IMPORTANT:
Turn off each system’s power supply (PoE hub or device to supply power to the camera) before
making a connection.
The 12 V DC power supply shall be insulated from the commercial AC power.
【1】
Connect an Ethernet cable (category 5e or better, straight) to RJ45
(female) network cable.
*
The maximum cable length is 100 m {328 feet}
.
IMPORTANT:
If the procedure for the RJ45 waterproof connector (accessory) part is not correctly followed, the
waterproofing may be compromised. Do not install the camera where the RJ45 waterproof
connector is exposed to constant rain or moisture.
The external dimensions of the Ethernet cable are from ø5 mm {ø3/16 inches} to ø6.5 mm {ø1/4inches}.
AFirst pass the Ethernet cable through the RJ45
waterproof connector cap (accessory) and then
through the RJ45 waterproof connector cover
(accessory). Next, use a specialized tool (locally
procured) to crimp the RJ45 plug (locally procured)
to the end of the Ethernet cable.
•
Take care not to remove the rubber parts from
inside the RJ45 waterproof connector cover.
BInsert the RJ45 plug into the RJ45 waterproof jack
connected to the camera.
C
Connect the RJ45 waterproof connector cover to the
RJ45 waterproof jack and then rotate the RJ45
waterproof connector cover until the "⇦" marks align.
D
Connect the RJ45 waterproof connector cap to the
RJ45 waterproof connector cover and rotate the
RJ45 waterproof connector cap until there is no gap
between it and the RJ45 waterproof connector cover.
RJ45
plug
(locally
pocured)
RJ45
waterproof
connector
cover
(accessory)
RJ45
waterproof
connector
cap
(accessory)
Ethernet
cable
RJ45
waterproof
jack
Connect the output cable of the AC adaptor to the 2P power cable (accessory).
【2】
When connecting an AC adaptor or an external power supply, use the 2P
power cable (accessory) to connect it to the camera.
【3】
If needed, connect the 4P alarm cable (accessory).
4P alarm cable (accessory)
GND (Black)
ALARM IN3 (Alarm input / AUX output) (Gray)
ALARM IN2 (Alarm input / Alarm output) (Red)
ALARM IN1 (Alarm input / Black & white input / Auto time adjustment input)
(Green)
Caution:
A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO THE
EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.
ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED
POWER SOURCE (IEC/EN/UL/CSA 60950-1).
Note:
The default of EXT I/O terminals is "Off". Refer to the Operating Instructions on the provid-
ed CD-ROM for further information about the EXT I/O terminal settings.
【4】
If needed, connect a microphone or the line out of an external device to the
audio input cable.
【5】
If needed, connect a powered speaker to the audio output cable.
Note:
The audio output can be switched to the monitor output. Refer to the "Operating
Instructions" on the provided CD-ROM for descriptions of how to switch the output.
IMPORTANT:
Stretch the tape by approx. twice (see the illustration) and wind it
around the cable. Insufficient tape stretch causes insufficient
waterproofing.
Stretch the tape to
about twice.
Wind the tape in a halfoverlapping manner.
Waterproof tape
(accessory)
(Red: 12 V DC side, Black: GND side)
Step 3 Mount the camera *There are 3 methods to install the camera to a ceiling or wall.
【
Type 1
】
Directly mount the camera onto the ceiling or wall.
【
Type 2
】
Mount the camera to a junction box.
【
Type 3】Mount the camera onto the ceiling or wall using the Adapter box (accessory)
Side B (upper)
⇧
TOP/
FRONT mark
2 PAN lock screws
(the other one is on
the opposite side)
2 upper screws
(M5:locally
procured)
TILT lock screw
Camera
mount
bracket
Note:
When installing on a wall, install the
camera mount bracket so that “⇧ TOP/
FRONT” faces upward.
When installing on a ceiling, install the
camera mount bracket so that “⇧ TOP/
FRONT” is aligned with the direction in
which the camera is pointed.
To run the cables to the side, pull out the
cables from the side cable access hole
provided at the side of the camera
mount bracket (see the illustration of
step B).
* 2 lower screws (M5), Minimum pull-out
strength: 724 N {163 lbf} (per 1 pc.). Secure
the camera through the holes in side B of the
camera mount bracket.
2 lower screws
(M5:locally procured)
Side cable
access hole
Side cable
access hole
2 Camera mount
bracket cover fixing
screws (accessory)
2 Camera mount bracket
covers (accessory)
Note:
When wiring cables on the side, use a
nipper to cut open a side cable
access hole of the camera mount
bracket cover, and then pass the
cable through.
As shown in the illustration to the lower right, install the camera to a junction box
using 4 fi xing screws (M4 screw with a washer with a diameter of 7.5 mm {5/16 inches} to
10 mm {3/8inches} and a spring washer
: locally procured) via the holes in side B of the
camera mount bracket.
*Minimum pull-out strength: 724 N {163 lbf} (per 1 pc.))
Note:
For installation procedures, refer to
step A, B, and C in
【
Type 1】.
Camera mount bracket
Side B (upper)
4 fixing screws
(M4:locally procured)
Junction
box
*The following explains an example of mounting the camera on a wall.
A
Using 4 M5 x 20 mm {13/16 inches} Mounting screws for adapter box (accessory), secure
the camera mount bracket to the adapter box via the holes in side A of the camera
mount bracket in the order of the top 2 holes to bottom 2 holes.
Recommended tightening torque: 1.86 N·m {1.37 lbf ft}
Note:
For installation procedures, refer to
step A and B in
【
Type 1】 .
2 Camera mount
bracket cover fixing
screws (accessory)
2 Camera mount
bracket covers (accessory)
4 Mounting screws for adapter box
(M5 x 20 mm {13/16 inches}:accessory)
Side A
(lower)
Step 4 Adjustment
SD memory card
(Ensure that the label
faces the lens.)
Auto focus (AF)
button
Auxiliary handle
(accessory)
MONITOR OUT jack
IMPORTANT:
Avoid touching the tilting part near the caution label
when you change the tilting angle to secure the camera.
Do not adjust the PAN rotation part more than ±180 °.
This may cause cables to be wrenched.
Note:
Any of the PAN, TILT and YAW lock screw can be adjusted by loosening them about 1 turn. Do
not unscrew them more than necessary.
Make sure the camera is supported by hand when loosening lock screws and adjusting the
direction of the camera.
Caution label
PAN lock
screw
TILT lock
screw
YAW lock screw
IMPORTANT:
Each bolt and nut or anchor (M6:locally pro-
cured) for securing the safety wire (accessory)
must have the minimum pull-out strength of
724 N {163 lbf}.
Be sure to secure the safety wire (accessory)
to the foundation of a structure or an area that
is strong enough.
Safety wire
(accessory)
■
When the camera is installed to the ceiling
■
When the camera is mounted on the wall
Bolt and nut or anchor
(M6:locally procured)
Safety wire
(accessory)
4 Front cover fixing screws
Front cover
A
B
C
D
WIDE
TELE
Bolt and nut or anchor
(M6:locally procured)
Adapter box
(accessory)
Zoom cover
C
*For WV-S1531LTN, the PAN lock screw
is also provided at the rear side. Tighten
it in the same manner as the front side.
x2