Panasonic wv-q2041s Operation Manual

Before attempting to mount this product,

please read these instructions carefully and save this manual for future use.

Rack Mount Bracket

These Rack Mounting Brackets are used for mounting such as the WJ-NT304, etc.

Model Nos.

WV-Q204/1S WV-Q204/2S

INSTALLATIONS

The installation described below should be made by qualified service personnel or system installers. Important: Recommended tightening torque is M3: 0.78 N·m (8 kgf·cm).

■ Mounting in a Rack

WV-Q204/1S can mount the WJ-NT304 on the rack. WV-Q204/2S can mount side by side up to two WJ-NT304S on the rack.

Illustrations as shown below are examples to install WJ-NT304 and WJ-NT304S.

1. Remove the four rubber feet from the bottom of the WJ-NT304.

● Mounting one WJ-NT304 with the WV-Q204/1S

2. Fix the mounting brackets (large and small) on both sides of the WJ-NT304 with the eight supplied screws (M3x8) as shown below.

Rubber feet

Rack mounting bracket (small)



Rack mounting bracket (large)

● Mounting two WJ-NT304 with the WV-Q204/2S

2. Place the joint metals on the WJ-NT304S as shown below and fix them with the supplied screws (M3x6) Note: Remove two screws from the rear of the WJ-NT304 beforehand.

3. Install the WJ-NT304S with the rack mounting brackets in the rack by using four screws (not included).

Cautions:

• Do not block the ventilation opening or slots in the cover to prevent the appliance from overheating. Always keep the temperature in the rack within +45°C (113°F).

• Secure the rear of the appliance to the rack by using additional mounting brackets (procured locally) if the rack is subject to vibration.

Mounting two WJ-NT304S

STANDARD ACCESSORIES

WV-Q204/1S: Mount Screw

Binding head (M3 x 8) .................. 8 pcs.

Specifications are subject to change without notice.

WV-Q204/2S: Mount Screw

Binding head (M3 x 8) ................. 8 pcs.

Flat head (M3 x 6) ...................... 12 pcs.

For further informations, refer to Operating Instructions of System Unit. When install the unit except CCTV system unit, use supplied tapping screws.

Fix the mounting brackets (small) on both sides of the WJ-NT304S with the eight supplied screws (M3x8) as shown below.

For U.S., Canadian and Puerto Rican fields:

Panasonic System Solutions Company,

Unit Company of Panasonic Corporation of North America

Security Systems

www.panasonic.com/security For customer support, call 1.877.733.3689

Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094 Zone Office Eastern: Three Panasonic Way, Secaucus, New Jersey 07094 Central: 1707 N. Randal Road, Elgin, IL 60123 Southern: 1225 Northbrook Parkway, Suwanee, GA 30024 Western: 6550 Katella Ave., Cypress, CA 90630

Panasonic Canada Inc.

5770 Ambler Drive,Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 http://www.panasonic.ca

Panasonic Sales Company

Division of Panasonic Puerto Rico Inc. San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina P.R. 00985(809)750-4300

For European and other fields:

Matsushita Electric Industrial Co., Ltd.

Osaka, Japan

http://panasonic.net

Rack mounting bracket (small)

Joint metal

Rack mounting bracket (small)

Rack mounting screws

Remove 2 screws from the rear beforehand.