Panasonic WV-Q152S, WV-Q152C User Manual

Ceiling Mount Bracket

Operating Instructions

WV-Q152C

Model Nos. WV-Q152S

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

No model number suffix is shown in this manual.

NM0806-1096 3TR004562BAA Printed in Japan

Preface

This bracket is exclusively designed to mount the network camera, DG-NS202, on a wall. The network camera shall be mounted on this bracket after mounting this bracket on a ceiling.

• WV-Q152C: Clear dome cover

• WV-Q152S: Smoked dome cover (approx. 50 % of transmittance)

Precautions

• Refer installation work to the dealer.

Installation work requires technique and experiences. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.

• Use only the specified camera.

Failure to observe this may cause a fall of an inappropriate camera resulting in injury or accidents. Mount WV-NS202 on this bracket exclusively.

• Avoid installing this bracket in the locations where salt damage occurs or corrosive gas is produced.

Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera may occur.

• The screws and fixation mechanisms shall be tightened securely.

Failure to observe this may cause a fall of the camera resulting in injury.

• Select an installation area that can support the total weight.

If a selected area is too weak to support the total weight, a fall of the product may occur resulting in injury. Installation work shall be started after sufficient reinforcement.

• Periodic inspections shall be conducted.

Rust on the metal parts or screws may cause a fall of the product resulting in injury. Consult the dealer for the inspections.

• The measures of protection against a fall of the camera shall be taken.

Failure to observe this may cause injury. Be sure to install the safety wire.

• Do not rub the edges of metal parts with your hand.

Failure to observe this may cause injury.

• Make sure that the installation area is strong enough to hold the total weight of the camera assembly (approx. 1.2 kg {2.6 lbs.}) before installation.

• The pull-out strength of the installation area shall be 196 N {20 kgf} or more per 1 screw. If a ceiling board such as plaster board is too weak to support the total weight, the area shall be sufficiently reinforced or the optional direct ceiling mount bracket for the camera, WV-Q105, shall be used.

• Procure 4 screws (M4 or M6) securing the camera mounting bracket (supplied with the camera) according to the material of the installation area. In this case, wood screws and nails should not be used. For mounting a camera on a concrete wall, use an anchor bolt (for M6) or an AY plug bolt (M4 or M6) manufactured by Matsushita Electric Works, Ltd. for securing. (Recommended tightening torque M4: 1.6 N·m {16 kgf·cm}, M6: 5.0 N·m {51 kgf·cm})

• Avoid installing in the following locations.

• Locations where it may get wet from rain or water splash (not only outdoor)

• Locations where a chemical agent is used such as a swimming pool

• Locations subject to steam and oil smoke such as a kitchen

• Locations where radiation or x-ray emissions are produced

• Locations where it may be damaged by briny air such as seashores

• Locations where the temperature is not within –10 °C - +50 °C {14 °F- 122°F}.

• Locations subject to vibrations (This product is not designed for on-vehicle use.)

• Locations where the temperature may rapidly change such as the peripheral areas of the air outlets of air conditioners or doors facing outside. (In case of installing the camera in such locations, the dome cover may become foggy or condensation may be caused on the cover.)

• The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area. After tightening the screws or bolts, perform visual check to ensure tightening is enough and there is no backlash.

• The protection sheet attached to the dome cover shall be peeled off after installation.

Major Operating Controls and Their Functions

* If a microphone is used, mount the microphone on the rubber-made microphone stand. Unless the

microphone is used, cut the rubber with a nipper or conduct another treatment.

LOCK

PEN

Notch for network cable, monitor output cable, etc.

Dome cover

Ceiling mount bracket

Hole for microphone cable

Microphone stand*

Installations

Be sure to read "Precautions" before installation. The Installation Guide of the network camera, WVNS202, shall be read as well.

1. Install the inner shell.

Slide the covers located on the both lateral sides of the camera and put the inner shell on the camera until the hooks inside the inner shell are held in the holes of the camera (until a click is heard).

Important: Put the inner shell down on the cam-

era until the outside cover of the camera cannot be seen from the opening (from which the camera lens is visible) of the inner shell. If this integration is not successfully performed, the inner shell may be removed or the hidden part at the top of the screen may become larger in the WIDE mode.

Cover

Hook

Put on until a click is heard

Inner shells

How to remove the inner shell

Press the inner shell from the front and rear sides inward (at the same vertical position as the hooks) to bend the shell and remove the shell from the camera.

Press from the front and rear sides inward to bend

(To be continued reverse page)

Anchor bolt (Procured locally)

Safety wire angle (WV-Q105 supplied)

Safety wire (WV-Q105 supplied)

Ceiling board such as plaster board

Ceiling mount bracket

Inner shell

Dome cover

Mounting screws (4 pcs.) WV-Q105 supplied)

WV-Q105 (option)

e Turn this bracket clockwise until the projection of the camera mounting bracket aligns with

"LOCK" of this bracket.

Specifications

Ambient temperature: –10 °C to +50 °C {14°F - 122°F} Dimensions: 185 mm {7-5/16"} in diameter x 163 mm {6-7/16"} in height Weight: Approx. 230 g Finish: Main body: ABS resin with silver metallic coating

Dome cover: Acrylic resin

Safety wire

Safety wire hook

Projection of camera mounting bracket

2. Mount the camera.

The camera shall be mounted on the camera mounting bracket (supplied with the camera) after mounting this bracket on a ceiling. For further information, refer to the operating instructions of WV-NS202.

w Mount this bracket on the camera with align-

ing the projection of the camera mounting bracket with "OPEN" of this bracket.

Important: Use caution not to catch the

cables.

Standard Accessories

Operating Instructions (this book) ....................... 1 pc.

The following are for installation.

Inner shell ............................................................ 1 pc.

Installations

(continued)

3. Install this bracket.

q Connect the safety wire locked on this

bracket to the safety wire hook. Make sure that the apical ring of the safety wire is engaged with the safety wire hook of the camera by pulling the safety wire after connection.

For European and other fields:

Matsushita Electric Industrial Co., Ltd.

Osaka, Japan

http://panasonic.net

For U.S., Canadian and Puerto Rican fields:

Panasonic System Solutions Company,

Unit Company of Panasonic Corporation of North America

Security Systems

www.panasonic.com/security For customer support, call 1.877.733.3689

Executive Office: Three Panasonic Way 2H-2, Secaucus,

New Jersey 07094

Zone Office Eastern: Three Panasonic Way, Secaucus, New Jersey 07094 Central: 1707 N. Randal Road, Elgin, IL 60123 Southern: 1225 Northbrook Parkway, Suwanee, GA 30024 Western: 6550 Katella Ave., Cypress, CA 90630

Panasonic Canada Inc.

5770 Ambler Drive,Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 http://www.panasonic.ca

Panasonic Sales Company

Division of Panasonic Puerto Rico Inc.

San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina P.R. 00985(809)750-4300

Note: When the camera lens is pointed in the horizontal direction, the inner shell interferes with

the camera’s view, and consequently about upper half of the monitor screen is hidden in the WIDE mode.

LOCK

PEN

OPEN

LOCK

LOCK OPEN