Panasonic VL-VN1500 Installation And Operating Instructions Manual
Installation and Operating Instructions
Video Intercom System — Door Station
Model No. VL-VN1500
Thank you for purchasing a Panasonic product.
Please follow all instructions in this document and save it for future reference.
Carefully read the information found in the section titled "Important safety information" in
particular.
This system is an auxiliary system; it is not designed to provide complete protection from
property loss. Panasonic will not be held responsible in the event that property loss occurs
while this system is in operation.
Note to the installer
R This document includes instructions for both installation and operation. See the
section titled "Installation" for installation instructions.
R Please read this document carefully, and install the product safely and correctly by
following the instructions.
R Only use attachments/accessories specified by the manufacturer.
R The installation shall be carried out in accordance with all applicable installation rules.
Table of Contents
Introduction
System overview .................................................3
Included items .....................................................3
Optional items
About this document ...........................................4
.....................................................3
Important information
Important safety information ...............................5
Important safety instructions ...............................5
Privacy and rights of portrait ...............................5
Data security .......................................................6
Disclaimer ...........................................................6
Other important information ................................6
General information ............................................7
For India only ......................................................8
For Europe ..........................................................8
Preparation
Device diagrams .................................................9
Installation
Installation cautions ..........................................10
Information about power connection .................10
Power over Ethernet (PoE) connection ............10
Installing the power supply unit (sold
separately) ........................................................10
Installing the door station ..................................12
Installing the relay box (sold separately) ..........15
Wire and cable specifications ...........................17
Other information
Specifications ....................................................18
Cleaning ............................................................19
Open source software notice ............................19
2
System overview
Th
is document explains basic information required
to install and configure a VL-VN1500 Door Station
for use with a Video Intercom System that is
comprised of the following devices.
R VL-MN1000 Room Monitor
R VL-VN1900 Lobby Station
R VL-VN1500 Door Station
R VL-VN1700 Control Box
Main features
Ca
mera features
R When a visitor calls you, you can view the
image from the door station camera on your
room monitor, and confirm who the visitor is
before talking or opening the door.
Other features
R The built-in card reader can be used to open a
door connected to an electric lock (user
supplied).
Included items
The following items are included in addition to the
door station.
Item Quantity
Mounting base 1
Introduction
Item Quantity
2-pin terminal block
ed to connect wires to the R1/R2
Us
connection terminals.
DC plug
s
ed to connect the power supply
U
unit to the door station.
1
1
Optional items
e following items are sold separately. Please
Th
contact your nearest Panasonic dealer for sales
information.
Compatible accessories (as of March, 2017)
Item Model no.
Power Supply Unit
ower supply unit that can be
P
used to power the door station
when no PoE power supply is
available.
Relay Box
ed to connect an electric lock
Us
(user supplied) to the door
station.
*1
VL-PS240
VL-RLY1
Screw (3 mm ´ 5
Used to secure the door station to
the mounting base.
Screw (3.8 mm ´
Used to secure the mounting base
to the wall.
mm)
2
0 mm)
*1 This product complies with the IEEE 802.3af
wer-over-Ethernet (PoE) standard. If PoE is
Po
available on your network, this product can
receive the necessary power from the network
through the Ethernet cable and no power
1
4
supply unit is needed. If PoE is not available,
you will need to connect a power supply unit to
the product.
Compatible system devices (as of March, 2017)
Item Model no.
Room Monitor
-compatible room monitor with
IP
touch screen. Typically installed
inside a residence.
VL-MN1000
3
Introduction
Item Model no.
Lobby Station
-compatible lobby station with
IP
colour screen, phonebook
features, and connection
terminals for external electric
lock, access controller, etc.
Typically installed in a lobby.
Control Box
lows the system to
Al
accommodate up to 2000 SIP
devices.
VL-VN1900
VL-VN1700
About this document
Terms and illustrations
R Mo
del number suffixes (e.g., the "BX" in
"VL-VN1500") are omitted unless necessary.
R Design and specifications are subject to change
without notice.
R Illustrations may vary slightly from the actual
product.
Trademarks
FARE is a registered trademark of NXP B.V.
R MI
and is used under license.
R All other trademarks identified herein are the
property of their respective owners.
4
Important safety information
WARNING
CAUTION
To
prevent severe injury and loss of life/property,
read this section carefully before using the product
to ensure proper and safe operation of your
product.
Note:
R If you are connecting a VL-PS240 power supply
unit to the product, refer to the documentation
included with the power supply unit for
additional safety information.
Preventing fi
R Leave installation work to the dealer.
Installation work requires technique and
experiences. Failure to observe this may
cause fire, electric shock, injury, or damage
to the product. Consult the dealer.
R Do not disassemble or modify the product.
Refer servicing to an authorised service centre
when service is required. Disassembling the
product or manipulating the product in a way not
described in the documentation may expose
you to dangerous voltages and other risks.
R Do not touch the product or the power supply
unit during an electrical storm. There may be a
remote risk of electric shock from lightning.
R Never install wiring during a lightning storm.
R Do not connect non-specified devices.
R When opening holes in walls for installation or
wiring, or when securing the power cable, make
sure you do not damage existing wiring and
ductwork.
R Do not make any wiring connections when the
power outlet is turned on.
R Do not install the product and power supply unit
in the following places:
– Places where the product and power supply
– Places where there is a high concentration of
R Do not push any objects through the openings
of the product.
R If any of the following conditions occur,
disconnect the Ethernet (LAN) cable from the
product, disconnect the power supply unit from
the power outlet, and then refer servicing to an
authorised service centre.
re, electric shock and short circuits
unit may be splashed with water or chemicals
dust or high humidity
Important information
– The product emits smoke, an abnormal smell
makes unusual noise
or
– The power cables are damaged or frayed
– Metal objects have been dropped inside the
product
R When existing wires are used, it is possible that
they contain AC voltage. Contact an authorised
service centre.
Preventing accidents, injuries, and property
mage
da
R Do not use the product in unstable areas or
areas prone to strong vibrations. This may
cause the product to fall, resulting in damage to
the product or injury.
R If the wiring passes outdoors, use a conduit and
a surge protector.
R If the wiring passes underground, use a conduit,
and do not make any connections underground.
R Install the product securely adhering to the
instructions in this document to prevent it from
falling off the wall. Avoid installing onto
low-strength walls, such as gypsum board, ALC
(autoclaved lightweight concrete), concrete
block, or veneer (less than 18 mm thick) walls.
R Do not put your ear(s) near the speaker, as loud
sounds emitted from the speaker may cause
hearing impairment.
Important safety instructions
When using this product, basic safety precautions
should always be followed to reduce the risk of
fire, electric shock, or personal injury.
Use only the power supply unit indicated in this
document.
SAVE THESE INSTRUCTIONS
Privacy and rights of portrait
Wh
en installing or using the product, please take
into consideration the rights of others with regard
to privacy.
R It is generally said that "privacy" means the
ability of an individual or group to stop
information about themselves from becoming
5
Important information
known to people other than those whom they
oose to give the information. "Rights of
ch
portrait" means the right to be safe from having
your own image taken and used indiscriminately
without consent.
Data security
In
order to use the system safely and correctly, the
data security guidelines (listed below) must be
observed. Failure to do so may result in the
following.
R Loss, leakage, falsification or theft of user
information.
R Unauthorised or illegal use of the system by a
third party.
R Interference or suspension of service caused by
a third party.
What is user information?
User information is defined as the following types
of information.
R Information stored in the product
– System event information
– System and device settings
R Information stored on the computer that is used
by the setup tool
– Resident names and room numbers
– System and device settings
Data security guidelines
R Observe proper management of passwords.
– Passwords can be used to program the
system, open doors, etc. Select passwords
that are difficult to guess, change them
regularly, and keep them secret. Assign a
unique password to each device.
R Protect user information when sending the
product to be repaired, or when handing it
over to a third party.
– Use the product's reset function to initialise
the product before when sending the product
to be repaired or handing it over to a third
party.
– Note that user information may be deleted or
initialized when the product is repaired.
– Refer all repairs to a trusted Panasonic
service centre.
R Protect user information stored on the
computer used to configure the system.
– When user information is stored on a
computer, the confidentiality of that
information becomes the responsibility of the
installer. Take precautions to prevent the
authorised use of the computer and the
un
setup tool used for performing system
configuration or maintenance.
– Connect the computer to the network only
when performing system configuration or
maintenance, and disconnect the computer
from the network as soon as the work is
complete.
– Before disposing of the computer, ensure that
data cannot be retrieved from it by formatting
the hard disk and/or rendering it physically
unusable.
R Protect user information when disposing of
the product.
– Use the product's reset function to initialise
the product before disposing of the product.
Disclaimer
R Re
corded data may be altered or deleted as a
result of incorrect operations, exposure to static
electricity, accidents, malfunction, repairs or
other operations.
R To the maximum extent permitted by law,
Panasonic assumes no responsibility for injuries
or property damage resulting from failures
arising out of improper installation or operation
inconsistent with this document.
Other important information
en you leave the product unused for a long
R Wh
period of time, unplug it from the power outlet.
R If you stop using this product, remove it from the
walls to prevent it from falling off.
R When power fails, this product cannot be used.
R Panasonic may not be liable for damages due to
external factors such as power failures.
6
Loading...