Panasonic TY S50PX20U User Manual

Placement

Assembly Instructions

TY-S42PX20U TY-S50PX20U Display stand

The tools required:

Plus (Phillips) (+) screwdriver

IMPORTANT

A study of the assembly instructions will not only save you time, but may prevent possible damage to your new stand. Assistance may be required for some assembly procedures.

CAUTION : THIS STAND IS DESIGNED ONLY FOR USE WITH A PANASONIC PLASMA TV. APPLIED MODEL : TH-42PX20, TH-50PX20

Use with other appliances may result in instability causing possible injury.

Your hardware pack contains / Replacement parts

Assembly screws Glass shelf fastening screws Glass shelf support fastening

screws (Black screws) ( × 4) Rear cord cover fastening

THEA118 × 4 THEA102N × 8 Support pole fastening screws

Support pole (Right) Support pole (Left) Cord clamps

Assembly screws (Black screws)

screws (Black screws) ( × 3)

XSB4+12FZ × 7XST5+12 × 4 XYN5+F55FZ × 4

STEP 1

∗ Install the plasma TV by referring to the following illustration. ∗ Do not hold the plasma TV at the bottom of the front panel.

1. Align the support pole insertion holes of the plasma TV with the support poles (1 each), and lower the plasma TV until the poles stop. Slightly lift the left and right sides of the plasma TV and remove the corner protection pads attached to the bottom.

2. Fasten the plasma TV and support poles

∗ Position by placing your hands at the

points indicated in the illustration.

STEP 2

• To thread wiring, remove the terminal cover and pass wires along the

grooves in the rear cord cover, along the groves in the left and right side panels, and along the groves in the cord holder under the glass shelf.

∗ Some equipment may have short cords. In such an instance, thread

the wiring over the minimum distance, as indicated by the dotted line in the diagram.

• After threading wiring, fasten with cord clamps (× 6) so that the cords

do not protrude from the grooves. Finally, attach the terminal cover.

If there are any cord clamps

need them if you use the unit to house more equipment in the future.

∗ The top glass shelf is specifically for the center speaker and AV

amp. If you place a video deck here, it may badly affect the picture.

Plasma TV installation and fastening method

using assembly screws (black screws) (× 4)

Support pole insertion hole

To use with equipment such as a video deck

left over, store them carefully. You will

Lift and remove

Support pole (Left)

Assembly screws (Black screws)

Support pole (Right)

∗ Wire over the minimum distance

(Back)

Cord clamps

Corner protection pad

Power cord

TBLA3196 × 1 Glass shelf supports (Right) Glass shelf supports (Left) Casters (Wheels)

TBLA3194 × 2

Replacement parts

Bottom cap (Right)

TBLB3107 × 1

TBLA3197 × 1 TBLB3111 × 6

TBLA3195 × 2 TBLB3074 × 4

Bottom cap (Left)

TBLB3108 × 1

Screws

XTB4+10B × 4

To maintain appearance we recommend the following:

Painted Surfaces:Use a damp cloth for cleaning. Do not use any abrasive or chemically treated cleaners. NOTE: As with all indoor furniture, this unit should not be exposed to direct sunlight, extreme temperatures or moisture, as this can result in serious irreparable damage.

For improvement purposes, design and specifications are subject to change without notice.

REPLACEMENT PARTS LIST

TY-S42PX20U

Ref. Description

Top crosspiece Bottom panel Side panel (Left) Side panel (Right)

Rear cord cover Glass shelf Cord holder

Qty. Part No.

1 TBLA0116 1 TBLH0548 1 TBLA0104 1 TBLA0103 1 TBLB3080 1 TKGA0127 1 TBLA3184

When making a part (s) inquiry or for out of warranty purchases please quote part no. & description.

PANASONIC SERVICES COMPANY

20421 84th Avenue South, Kent, Washington 98032 Tel. : 1-800-833-9626 Fax : 1-800-237-9080

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3 Tel. : (905) 624-8447

TQZH507 Printed in Japan

TY-S50PX20U

Part No.

TBLA0117 TBLH0550 TBLA0104 TBLA0103 TBLB3110 TKGA0129 TBLA3217

Assembly & Placement Manual

Assembly

STEP 1

1. Securely insert the casters (× 4) into the bottom panel.

2. Align the dowels of the side panels (left and right) with the dowel holes in the bottom panel and insert.

STEP 2

1. Align the support pole (right) with the notch on the right side of the top crosspiece, and securely fasten with the support pole fastening screws screwdriver. Fasten the support pole (left) to the left side in the same manner.

2. Insert the rear cord cover fastening screws (black screws) the back of the top crosspiece and partially fasten. Slide the 3 notches in the rear cord cover behind the screws and securely fasten the screws.

3. Align the dowels of the side panels (left and right) with the dowel holes in the top crosspiece and insert. Securely fasten with assembly screws

Attaching of bottom panel, side panels and casters

Side panel (Left)

Bottom panel

Dowels

Dowel holes

Front

Casters

Attaching of top crosspiece and rear cord cover

(× 2) using a Phillips head (+)

(× 3) into the screw holes on

(× 4).

Side panel (Right)

Support pole fastening screws

Support pole (Right)

Rear cord cover fastening screws (Black screws)

Side panel (Left)

Model No.

Top crosspiece

Notches

Rear cord cover

Assembly screws

TY-S42PX20U TY-S50PX20U

Dowels

Dowel holes

Notches

Side panel (Right)

STEP 3

1. Align the dowels in the glass shelf supports (left) (× 2) with the dowel holes in the side panel (left) and insert. Securely fasten with the glass shelf support fastening screws (black screws)

2. Attach the glass shelf supports (right) manner.

3. Insert a cord holder in parallel with the glass shelf supports (left and right), and align the dowels of the cord holder with the dowel holes in the glass shelf supports. Attach the other cord holder to the other glass shelf supports in the same manner.

4. Attach the caution label to one glass shelf on the right side, facing the front. Insert the glass shelf in parallel with the grooves in the glass shelf supports (left and right), and securely fasten to the bottom of the (left and right) glass shelf supports using the glass shelf fastening screws

(× 4). Fit the other glass shelf

in the same manner.

Attaching of glass shelf and cord holder

(×1).

in the same

The tools required:

Plus (Phillips) (+) screwdriver

∗∗

∗ Do not use electric powered screwdrivers.

∗∗

Side panel (Left)

Glass shelf supports (Left)

Glass shelf support fastening screws (Black screws)

Glass shelf supports (left and right)

Dowel / hole

Cord holder

Glass shelf

Glass shelf fastening screws

∗ Position the glass shelf such that the caution

label is on the top surface, on the near side.

∗ Do not load either glass shelf with equipment

weighing over 12 kg (26 Ib.). Do not load the bottom storage area with equipment weighing over 20 kg (44 Ib.).

Dowel holes

Caution label

TQZH507 Printed in Japan