Please read these instructions before operating your set and retain them for future reference.
English
TQB0E0221
Welcome
Dear Panasonic Customer,
We hope that you have many years of enjoyment from your new TV. The Quick Start Guide section at the be gin ning of
this instruction book will allow you to use the TV as quickly as possible. We recommend that you then read the complete
instruction book, and keep it to refer to as you explore the range of advanced features that this LCD TV offers.
Contents
Warnings and Precautions ......................................... 3
• This TV set is designed to operate on AC 220-240 V, 50
/ 60 Hz.
• To prevent damage which might result in elec tric shock
or fi re, do not expose this TV set to rain or excessive
moisture. This TV must not be exposed to dripping or
splashing water and ob jects fi lled with liq uid, such as
vases, must not be placed on top of or above the TV.
• Keep unneeded small parts and other objects out
of the reach of small children. These objects can be
accidentally swallowed. Also, be careful about packaging
materials and plastic sheets.
• WARNING: HIGH VOLTAGE!!!
Do not remove the rear cover as live parts are accessible
when it is removed. There are no user serviceable parts
inside.
Ensure that the mains plug is easily accessible.
• TV Games / Home Computers
Extended use of TV games or home computers with
any television set can cause a ‘shadow’ on the screen.
This type of LCD panel phenomenon, can be limited by
observing the following points:
• Reduce the brightness and contrast levels to a minimum
viewing level.
• Do not allow a still picture to be displayed for an extended
period, as this can cause a permanent after-image to remain
on the LCD TV screen.
•
Examples of still pictures include logos, video games, computer
images, teletext and images displayed in 4:3 mode.
• This type of LCD panel damage, is not an operating defect,
and as such is not covered by the Panasonic warranty.
• The On / Off switch on this model does not fully
disconnect the TV from the mains supply. Remove the
mains plug from the wall socket before connecting or
disconnecting any leads, or if the TV set is not used for
a prolonged period of time.
Note:
If the set is not switched off when the TV station stops
transmitting, it will automatically go to Standby mode after
30 minutes. This function will not operate when the TV
is in AV mode.
• Cabinet and LCD panel care
Remove the mains plug from the wall socket. The
cabinet and LCD panel can be cleaned with a soft cloth
moistened with mild detergent and water. Do not use
solutions containing benzol or petroleum.
• When ambient temperature is cool, the picture may take
a short time to reach normal brightness, but this is not
a malfunction. (After brief moment, the picture will have
normal brightness.)
• Adequate ventilation is essential to prevent failure of
electrical components, we recommend that a gap of at
least 10 cm is left all around this television receiver even
when it is placed inside a cabinet or between shelves.
• Avoid exposing the TV set to direct sunlight and other
sources of heat. To prevent fi re, never place any type
of candle or naked fl ame on top or near the TV set.
• Ventilation should not be impleded by covering the
ventilation openings with items such as newspapers,
tablecloths and curtains.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY
This appliance is supplied with a fi tted three pin mains plug for your safety and convenience. A 5 amp fuse is fi tted in this plug.
If the fuse is replaced then the replacement fuse must be 5 amp rated and should be approved by ASTA or BSI to BS1362.
Check for the ASTA mark
If the fi tted plug has a removable fuse cover you must ensure that it is refi tted when the fuse is replaced. If you lose the fuse
cover the plug must not be used until a replacement cover is obtained. Replacement fuse covers can be purchased through
your local Panasonic dealer.
The plug fi tted to this appliance incorporates a mains fi lter circuit. If this is removed or replaced with
a non– fi ltered plug this television will no longer meet the European standards for Electromagnetic
Compatibility (EMC). If the fi tted plug is unsuitable for the socket outlet in your home an appropriate
adapter should be used.
Nonetheless, if the fi tted plug is replaced, the fuse should be taken out and the cut- off plug disposed
of safely. There is danger of severe electrical shock if the cut off plug is inserted into any 13 amp
socket.
If a new plug is to be fi tted please observe the wiring code as shown below.
If in any doubt please consult a qualifi ed electrician.
How to replace the fuse (for plug type shown in example 1):
Lift out the removable fuse compartment with a screwdriver and replace the fuse, then refi t securely into the
mains plug (see example 1).
How to replace the fuse (for plug type shown in example 2):
Lift open the fuse compartment, in the mains plug, with a screwdriver, and replace the fuse, then press the fuse cover down
securely (see example 2).
IMPORTANT: – The wires in the mains lead of this appliance are coloured in accordance with the following code:–
BLUE : NEUTRAL BROWN : LIVE
As the colours of the wires in the mains lead of this appliance may not correspond to the markings identifying the terminals in your
plug, proceed as follows:–
1. The BLUE wire must be connected to the terminal marked ‘N’ or coloured black.
2. The BROWN wire must be connected to the terminal marked ‘L’ or coloured red.
IMPORTANT NOTE: Under no circumstances should either of these wires be connected to the Earth terminal of the three pin plug,
ASA
or the BSI mark on the body of the fuse.
marked with the letter ‘E’ or the earth symbol
Example 1
Example 2
.
3
Accessories
Check that you have the accessories and items shown
Operating Instructions
Clamper
(TMME203)
Remote Control Transmitter
(EUR7651090)
OK
123
456
789
C
0
N
TV
Pan European Guarantee Card
Batteries for the Re mote
Control Transmitter
(2 × R6 (UM3) size)
Fitting remote control batteries
321
+
+
-
“R6 (UM3)” size
Pull and hold the hook, then
open the battery cover.
Insert batteries - note correct
polarity ( + and -).
• Make sure that the batteries are fi tted the correct way round.
• Do not mix old batteries with new batteries. Remove old, exhausted batteries immediately.
• Do not mix different battery types, i.e. Alkaline and Manganese or use rechargeable (Ni-Cad) batteries.
4
Replace the cover.
Cable cover removal and fi tting
Removal
1. Push down hooks and pull the cover slightly towards
yourself to disengage the claws (at 3 points).
2. Slowly pull out in the downward direction.
Fitting
1. Insert the claws (at 3 points) at the bottom end.
2. Push until it clicks.
Note:
To avoid interference appearing on the screen, do not bundle the RF cable and mains lead together.
How to open the front cover
PULL
How to use the LCD stand
Adjust the LCD panel to your desired angle.
The LCD panel can be adjusted the following direction:
20° Right
20° Left
PULL
Raise the lower part of the door
marked “PULL”.
(View from the top)
5
Quick Start Guide
Connection and setting up options
Note:
Please ensure that the unit is disconnected from the mains
before attaching or disconnecting any leads.
AV1AV2AV 4
COMPONENT
L
R
AUDIO
RGB
VIDEO
VIDEO
S-VIDEO
RGB
VIDEO
S-VIDEO
VIDEO
Scart cables
Y
(Not supplied)
B
P
PR
RF cable
(Not supplied)
SET TOP BOX
RF cable (Not supplied)
VCR / DVD
OR
Recorder
Scart Connections
• The VCR / DVD Recorder can be connected to the TV using a Scart cable, if you are using a Scart equipped VCR
/ DVD Recorder.
• Use the TV’s any Scart terminal for any VCR. Always use a “fully wired” Scart cable.
• Use the TV’s AV1 or AV4 Scart terminal for any DVD Recorder. Always use a “fully wired” Scart cable.
• Use the TV’s AV1 or AV4 Scart terminal for Satellite Receiver. Always use a “fully wired” Scart cable.
RF Connection
• Connect the RF cable to the “Aerial In” terminal of the VCR / DVD Recorder and an RF cable from the VCR / DVD
Recorder “Aerial Out” terminal to the TV Aerial terminal ( ).
Notes:
• If using a “Q-Link” VCR / DVD Recorder, then the AV1 Scart of the VCR / DVD Recorder must be connected to the
AV2 or AV4 terminal of the TV. If your VCR or DVD Recorder is not a “Q-Link” device, please consult the operating
instruction book for that product. Further information on Q-Link can be found on page 21.
• Further details of Audio / Video connections can be found on page 28-30.
• Additional equipment and cables are not supplied.
6
Quick Start Guide
Connect the mains plug to the wall sock et.
1
Press the [
set on.
] switch on the TV set to turn the
OK
To switch the TV set to Standby mode, press the
button on the remote control.
The TV set can be switched on by pressing the
button again if it was in Stand by mode.
Note:
This TV will still consume some power even in
the Off mode, as long as the mains plug is still
connected to a live mains socket.
C.A.T.S. sensor
LCD C.A.T.S. (Contrast Automatic Tracking System) automatically
senses the ambient light conditions and adjusts the brightness and
gradation accordingly, to optimize contrast.
C.A.T.S. is in effect when Viewing mode is set to Auto. See page 11.
Programmes will appear immediately if your dealer has programmed
2
the TV for you.
If the TV has not been programmed for you then Auto setup will
begin.
The TV will search for Analogue stations:
TV stations will be located, sorted into order and stored ready for
use.
PULL
Power Indicator
Standby : Red
On : No Light
Remote control signal sensor
CH12
AUTO SETUP IN PROGRESS
SEARCHING : PLEASE WAIT
01 99:21 41
Exit
123
456
789
C
0
N
TV
Analogue stations are sorted into channel order, but can be changed to your preference. See page 15.
The sorted programme order depends upon the TV signal, the broadcasting system, and reception
conditions.
TV to VCR or DVD Recorder Download
3
If a “Q-Link”, “NEXTVIEWLINK” or compatible recording device has been
connected to a Scart terminal (AV2 or AV4) before starting Step 1, programme
information will be downloaded to that device.
DOWNLOAD IN PROGRESS
PLEASE WAIT
Programme : 63
Remote control unavailable
The programme positions will be downloaded to the recording device, in the same order as stored in the TV.
See page 21.
Not all VCRs / DVD Recorders support this download of programme information, some may require to be
started manually.
Refer to the recording device’s operating instruction book.
If a recording device other than those described above has been connected, then there will be no download
operation.
Notes:
• If the recording device has not accepted download data from the TV, you may need to select the Download
option from the device’s menu system. Refer to the recording device’s operating instruction book.
• If Q-Link is not operating correctly, check the following:
The Scart cable is connected to the TV’s Scart terminal, AV2 or AV4, and correctly setup in the menu.
The Scart cable is connected to the recording device’s compatible (Q-Link, NEXTVIEWLINK or similar
technology) Scart terminal.
The Scart cable is a “fully wired” type.
• For further information on Q-Link and connecting equipment, see page 21, 29, 32.
7
Quick Start Guide
Owner ID
4
As an added feature, this TV has the option of adding a security code
(Owner ID) and personal details into its memory, so that in the unfortunate
event of theft it will help the Police to trace the owner.
Using the numeric buttons to enter required 4 digit Owner ID PIN NUMBER.
If a 4 digit PIN NUMBER was entered, you will be taken automatically
to the NAME line.
If not, using the left or right cursor buttons move to the NAME line.
Change character using the up or down cursor buttons.
123
456
789
0
VCR
OK
123
456
789
C
0
N
Select the character position using the left or right cursor buttons.
Repeat above until NAME, HOUSE NUMBER and POSTCODE are
entered.
Press the OK button to store the details.
Press the OK button again, when you are asked “Are you sure ?”.
For further information on Owner I.D., see page 19.
A space is provided on page 19 to write down the PIN NUMBER for
future reference.
Your LCD TV is now ready for use.
To view a list of the stations that have been found, press the GUIDE
5
button.
Use the cursor buttons to move the cursor bar.
Use the programme change button to step through the guide page by
page.
To view the selected programme, move the cursor to the channel and
then press the OK button.
The guide can be cleared from the screen using the EXIT button.
OK
Owner ID
PIN NUMBER :
POSTCODE :
GUIDE
OK
EXIT
NAME :
HOUSE NO :
0123456789
TV
You now have the opportunity
to enter your details and
help the police crack crime
see instruction book
F (Function select)
Displays the On Screen Display functions, use
repeatedly to select from the available functions -
Volume, Contrast, Brightness, Colour, Sharpness,
Tint (in NTSC mode), Bass, Treble, Balance and
Tuning mode.
Standby On / Off buttonSwitches TV On or Off (Standby mode).
GUIDE button
Displays the Programme table.
Move the cursor to choose the position,
then press the OK button to the viewing
screen.
Menu button
Press to access the Picture, Sound and
Setup menus. (see page 10-13)
Press
to
select a function or store a setting.
Press after selecting programme positions
to quickly change programme.
MENU
TEXT
Headphones jack
(see page 28)
TV/AV button (see page 28)
Press either button to change TV programme up or down.
Also used for changing various settings in conjunction with the F
button.
Press either button to switch the TV On from Standby mode.
DIRECT TV REC
TV/AVGUIDE
OK
EXIT
F.P. INDEX HOLD
AV3 terminals
(see page 28)
Sound mute On / Off
DIRECT TV Record button
(see page 21)
Switch between viewing TV or AV input.
(see page 28)
Cursor buttons to make selections and
adjustments.
Exit the mode.
Text Hold / Picture Still button
(see page 25, 27)
Coloured buttons used for the selection,
navigation and operation of various
functions.
Teletext button (see page 25-27)
Text F.P. button (see page 26)
Direct channel access
During normal TV viewing or when
in the Tuning, Programme edit or Manual tuning menus, press and then
enter channel number using the numeric
buttons.
Programme up / down button
ASPECT control button
(see page 22, 23)
N (Normalize) button
Resets all settings to their default levels.
123
456
789
C
ASPECT
PROGRAMME
N
REC
0
VCR
VCR DVD
TV
Text Index button (see page 27)
Programme / channel change buttons (0-
9) and Teletext page buttons.
(see page 25-27)
When in Standby mode, switches TV
On.
Information button
Press to display status information for the
current Programme position.
Volume up / down button
VCR / DVD buttons
(see page 24)
9
Using the On Screen Displays
Many features available on this TV can be accessed via the On Screen Display menu system. Use the remote control
as shown below to access and adjust features as desired.
The MENU button is used to open the main menus and also
to return to the previous menu.
The up and down cursor buttons are used to move the
cursor and select menus.
The left and right cursor buttons are used to access menus,
adjust levels or to select from a range of options.
The OK button is used with a number of features to store
settings after adjustments have been made or options have
been set.
The EXIT button is used to exit the menu system and re turn
to the normal viewing screen.
An On Screen Help box is displayed whenever a menu is
dis played on the TV. This Help box indicates which buttons on
the remote control are used to navigate the menu shown, see
above for descriptions of button functions.
Note:
The Help box is not shown in the menu pictures in this in struc tion
book due to space limitations.
Press the EXIT button at any time to go back to watching TV.
Viewing modeThe Viewing mode menu allows you to select four different
screen settings - Dynamic, Normal, Cinema and Auto.
In each Viewing mode setting, Contrast, Brightness,
Colour, Sharpness, Tint (in NTSC only), Colour balance,
Colour management, P-NR, MPEG NR and 3D-COMB
can be adjusted and stored to suit your particular viewing
requirement. (e.g., you may require different settings for
viewing sports, fi lms, news etc.)
Changes to any settings in a viewing mode will affect all
signal sources: RF, AV1, AV2, AV3, AV4, Component and
HDMI. Changes will be stored automatically. By analysing
and processing the incoming picture, all four modes feature
automatic enhancement.
Contrast, Brightness, Colour, Sharpness
Increase or decrease the levels of these options ac cord ing
to your personal preference.
TintWith an NTSC signal source connected to the TV, the picture
hue can be adjusted to suit your taste.
Colour balance Allows you to set the overall colour tone of the picture.
Choose from Cool, Normal and Warm.
Colour
Enables vivid colour adjustment automatically.
management
P-NRAutomatically reduces unwanted picture noise.
Not available during HDMI and HD signal input.
MPEG NRReduces MPEG noise.
Allows you to choose from Off, Min, Mid and Max.
This function is effective in reducing the digital block noise
when viewing DVD, VCD or digital broad cast ing. The effect
will be changed based on the scene and image.
MPEG: Compression technology of the image signal
adopted by DVD, VCD or digital broadcasting.
3D-COMBOccasionally, whilst viewing still or slow moving pic tures,
colour patterning may be seen. Set 3D-COMB to On to
display sharper and more accurate colours.
Displayed only when receiving PAL or NTSC signals.
Not displayed during RGB Video, S-Video, Component and
HDMI input mode.