Thank you for purchasing this product.
Please read these instructions carefully before using this product,
and save this manual for future use.
Model number suffix “EB” denotes UK model.
RQT9731-1B
Caution for AC Mains Lead
Figure AFigure B
Fuse cover
Figure A
Fuse
(5 ampere)
Figure B
Fuse
(5 ampere)
(For the AC mains plug of three pins)
For your safety, please read the following text
carefully.
This appliance is supplied with a moulded three pin
mains plug for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure
that the replacement fuse has a rating of 5-ampere
and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark Ï or the BSI mark Ì on
the body of the fuse.
If the plug contains a removable fuse cover you
must ensure that it is refitted when the fuse is
replaced.
If you lose the fuse cover the plug must not be used
until a replacement cover is obtained.
A replacement fuse cover can be purchased from
your local dealer.
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to the type
of AC mains plug (figures A and B). Confirm the AC
mains plug fitted and follow the instructions below.
Illustrations may differ from actual AC mains plug.
1. Open the fuse cover with a screwdriver.
2. Replace the fuse and close or attach the fuse
cover.
2
RQT9731
Safety precautions
WARNING
Unit
≥ To reduce the risk of fire, electric shock or product damage,
– Do not expose this unit to rain, moisture, dripping or
splashing.
– Do not place objects filled with liquids, such as vases, on
this unit.
– Use only the recommended accessories.
– Do not remove covers.
– Do not repair this unit by yourself. Refer servicing to
qualified service personnel.
– Do not let metal objects fall inside this unit.
– Do not place heavy items on this unit.
AC mains lead
≥ To reduce the risk of fire, electric shock or product damage,
– Ensure that the power supply voltage corresponds to the
voltage printed on this unit.
– Insert the mains plug fully into the socket outlet.
– Do not pull, bend, or place heavy items on the lead.
– Do not handle the plug with wet hands.
– Hold onto the mains plug body when disconnecting the
plug.
– Do not use a damaged mains plug or socket outlet.
≥ The mains plug is the disconnecting device.
Install this unit so that the mains plug can be unplugged from
the socket outlet immediately.
Button-type battery (Lithium battery)
≥ Risk of fire, explosion and burns. Do not recharge,
disassemble, heat above 60
≥ Keep the Button-Type battery out of the reach of children.
Never put Button-Type battery in mouth. If swallowed call
your doctor.
CAUTION
Unit
≥ This unit utilizes a laser. Use of controls or adjustments or
performance of procedures other than those specified herein
may result in hazardous radiation exposure.
≥ Do not place sources of naked flames, such as lighted
candles, on this unit.
≥ This unit may receive radio interference caused by mobile
telephones during use. If such interference occurs, please
increase separation between this unit and the mobile
telephone.
≥ This unit is intended for use in moderate climates.
Placement
≥ Place this unit on an even surface.
≥ To reduce the risk of fire, electric shock or product damage,
– Do not install or place this unit in a bookcase, built-in
cabinet or in another confined space. Ensure this unit is
well ventilated.
– Do not obstruct this unit’s ventilation openings with
newspapers, tablecloths, curtains, and similar items.
– Do not expose this unit to direct sunlight, high
temperatures, high humidity, and excessive vibration.
o
C or incinerate.
Button-type battery (Lithium battery)
≥ Danger of explosion if battery is incorrectly replaced.
Replace only with the type recommended by the
manufacturer.
≥ Insert with poles aligned.
≥ Mishandling of batteries can cause electrolyte leakage and
may cause a fire.
– Remove the battery if you do not intend to use the remote
control for a long period of time. Store in a cool, dark
place.
– Do not heat or expose to flame.
– Do not leave the battery(ies) in a car exposed to direct
sunlight for a long period of time with doors and windows
closed.
≥ When disposing the batteries, please contact your local
authorities or dealer and ask for the correct method of
disposal.
Product Identification Marking is located on the bottom of
the unit.
Sales and Support Information
Customer Communications Centre
≥ For customers within the UK: 0844 844 3899
≥ For customers within Ireland: 01 289 8333
≥ Monday–Friday 9:00 am - 5:00 pm
(Excluding public holidays).
≥ For further support on your product, please visit
our website: www.panasonic.co.uk
Direct Sales at Panasonic UK
≥ Order accessory and consumable items for your
product with ease and confidence by phoning our
Customer Communications Centre
Monday–Friday 9:00 am - 5:00 pm
(Excluding public holidays).
≥ Or go on line through our Internet Accessory
ordering application at www.pas-europe.com.
≥ Most major credit and debit cards accepted.
≥ All enquiries transactions and distribution
facilities are provided directly by Panasonic UK.
≥ It couldn’t be simpler!
≥ Also available through our Internet is direct
shopping for a wide range of finished products.
Take a browse on our website for further details.
Table of contents
Caution for AC Mains Lead....................................2
to this unit ..........................................................19
About descriptions in these operating instructions
≥ Pages to be referred to are indicated as “l ±±”.
≥ These operating instructions are applicable to models
SC-HC28DB and SC-HC18. Unless otherwise indicated,
illustrations in these operating instructions are of
SC-HC28DB.
[SC-HC28DB] :
[SC-HC18] :
indicates features applicable to SC-HC28DB
only.
indicates features applicable to SC-HC18
only.
Accessories
Check the supplied accessories before using this unit.
∏ 1 Remote control
(with a battery)
[SC-HC28DB]
(N2QAYC000079)
[SC-HC18]
(N2QAYC000080)
∏ [SC-HC28DB]
1 DAB antenna
(N1EADY000001)
∏ [SC-HC28DB]
1 Pad sheet (l 19)
(RFA3465)
∏ 1 AC mains lead
(K2CT2YY00097)
∏ [SC-HC18]
1 FM indoor
antenna
(RSAX0002)
∏ [SC-HC18]
1 Antenna plug
adaptor
(K1YZ02000013)
≥ Do not use AC mains lead with other equipment.
≥ Product numbers provided in these operating instructions are
correct as of December 2012. These may be subject to
change.
RQT9731
3
Control reference guide
23814131
PUSH
15
18
1716
iPod/
USB
12
11
10
9
8
7
6
5
4
3
2
1
Top view
[SC-HC18]
[SC-HC18]
[SC-HC18]
[SC-HC18]
Unless otherwise indicated, operations are described
using the remote control.
1 Standby/on switch (Í/I) (Í)
Press to switch the unit from on to standby mode or vice
versa.
In standby mode, the unit is still consuming a small
amount of power.
2 Select the audio source
3 Basic playback control buttons
4 Enter setup menu
5 Change displayed information
[SC-HC28DB] Enter the iPod/iPhone menu
6 Set the sleep timer
7 Change the brightness of the display panel
8 Adjust the volume (0 (min) to 50 (max))
9 Mute the sound
Mutes the sound. Press again to cancel. “MUTE”
is also cancelled when the volume is adjusted or
the unit is turned off.
10 Enter playback menu
11 Enter sound menu
12 Selection/OK
13 [SC-HC28DB]
“IPOD_PORT” for iPod/iPhone/iPad (l 6)
USB port (l 6)[SC-HC18] USB port (l 6)
14 Open or close the sliding door
15 Sliding door
16 Display
17 Remote control signal sensor
Distance: Within approx. 7 m directly in front.
≥ To avoid interference, please do not put any objects in
front of signal sensor.
18 [SC-HC28DB] “IPOD_DOCK” for iPod/iPhone/
iPad mini (l 6)
USB
RADIOiPod
/USB
USBRADIO
iPad
/
CLOSE
VOLUME
OPEN
∫ Before using for the first time
Remove the insulation sheet A.
≥ Set the button-type battery with its (i) mark facing upward.
≥ Keep the button-type battery out of reach of children to prevent swallowing.
4
RQT9731
∫ To replace a button-type battery
Battery type: CR2025 (Lithium battery)
Connections
ョヮチモワヵ
チドヘブナ
ュモャチモワヵ
1
2
ョヮチモワヵ
チドヘブナ
ュモャチモワヵ
Connect the AC mains lead after all other connections are completed.
This unit consumes a small amount of AC power (l 16) even when turned off.
≥ In the interest of power conservation, if you will not be using this unit for an extended period of time, unplug it from
the household mains socket.
Adhesive tape (not supplied)
DAB indoor antenna
(supplied)
Be sure to tighten fully the
nut.
AC mains lead (supplied)
To household mains socket
FM indoor antenna
(supplied)
Adhesive tape
(not supplied)
[SC-HC28DB]
[SC-HC18]
Lens
ョヮチモワヵ
ヘブ
モヮチモワヵロヰヰヱ
READ THE CAUTION FOR THE AC MAINS LEAD ON PAGE 2 BEFORE CONNECTION.
≥ These speakers do not have magnetic shielding. Do not place them near a television, personal computer or other devices easily
influenced by magnetism.
≥ Tape the DAB/FM antenna to a wall or column in a position with the least amount of interference. (Use an DAB/FM outdoor
antenna if radio reception is poor.)
Unit and media care
Pull out the AC mains lead from the outlet before
maintenance.
∫ Clean this unit with a soft, dry cloth
≥ When dirt is heavy, wring a cloth moistened in water tightly to
wipe the dirt, and then wipe it with a dry cloth.
≥ Never use alcohol, paint thinner or benzine to clean this unit.
≥ Before using chemically treated cloth, carefully read the
instructions that came with the cloth.
∫ Maintenance of the lens
≥ Clean the lens regularly to prevent malfunctions. Use a
blower to remove dust and a cotton swab if it is extremely
dirty.
≥ You cannot use a CD type lens cleaner.
≥ Do not leave the sliding door open for prolonged periods
of time. This will cause the lens to get dirty.
≥ Be careful not to touch the lens with your fingers.
∫ Clean discs
DODO NOT
Wipe with a damp cloth and then wipe dry.
∫ Disc handling precautions
≥ Handle discs by the edges to avoid inadvertent scratches or
fingerprints on the disc.
≥ Do not attach labels or stickers to discs.
≥ Do not use record cleaning sprays, benzine, thinner, static
electricity prevention liquids or any other solvent.
≥ Do not use the following discs:
– Discs with exposed adhesive from removed stickers or
labels (rented discs etc.).
– Discs that are badly warped or cracked.
– Irregularly shaped discs, such as heart shapes.
∫ To dispose or transfer this unit
The unit may keep the user settings information in the
unit. If you discard this unit either by disposal or transfer,
then follow the procedure to return all the settings to the
factory presets to delete the user settings.
(l12, “To return all settings to the factory preset”)
5
RQT9731
Inserting media
PUSH
OPEN/CLOSE
[SC-HC28DB]
Select “IPOD_DOCK” as the source
Connect using the Lightning connector *1
[SC-HC28DB]
Select “IPOD_PORT” as the source
“USB” is displayed when a compatible USB is inserted.
[SC-HC18]
Select “USB” as the source
Select “CD” as the source
*1, 2, 3
*4
*5
*6
[SC-HC28DB]
[SC-HC28DB] Attach the pad before using this unit.
(l 19)
pad
(supplied)
iPad
/USB
RADIOiPod
VOLUME
*1: Refer to “Playable media” for compatible models. (l 14)
– Do not connect an iPad (4th generation) to the
“IPOD_DOCK” connection. This unit might fall over.
Use the “IPOD_PORT” connection.
*2: When using the “IPOD_PORT” connection, do not connect
the following models to this unit:
– iPod classic, iPod [4th (colour display), and 5th (video)
generation]
Unexpected behaviour may occur.
*3: Connect using the dedicated USB cable (not supplied).
*4: Insert the USB device directly. Do not use any USB
extension cable.
*5: When using the “IPOD_DOCK” connection:
≥
Be sure to remove the iPod/iPhone/iPad mini from its case.
≥
Make sure that the iPod/iPhone/iPad mini is fully inserted.
≥ If the
iPod/iPhone/iPad mini
make sure to check that it is still fully inserted.
≥ Make sure to hold the dock when removing the iPod/
iPhone/iPad mini.
≥ Make sure to close the dock properly after using it.
If not,
– The sliding door will not open.
– The standby power consumption will increase.
*6: Make sure to tilt the disc so as not to touch the sliding door.
is pushed to the left or right,
6
RQT9731
/
CLOSE
OPEN
≥ Do not open the sliding door manually.
≥ Make sure that the unit does not fall when inserting or
removing media.
≥ When moving this unit, be sure to remove all media and turn
this unit to standby mode.
≥ Before removing the USB device, select a source other than
“USB”.
[SC-HC28DB]
Charging an iPod/iPhone/iPad
Charging starts when an iPod*2/iPhone/iPad is
connected to this unit.
≥ During standby mode, charging will not start from the
“IPOD_PORT” connection, however it will start as usual from
the “IPOD_DOCK” connection.
– To charge from the “IPOD_PORT” connection, start the
charging before turning this unit to standby mode.
≥ Check the iPod/iPhone/iPad to see if the battery is fully
charged. (Once fully recharged, additional recharging will not
occur.)
≥ If this unit is switched to standby mode
“IPOD CHARGING” is shown on the unit’s display.
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.