Panasonic SC-HC1020 User Manual

EGEBGN

Operating Instructions

Compact Stereo System

Thank you for purchasing this product. Please read these instructions carefully before using this product,

and save this manual for future use.

Model No. SC-HC1020

Included Installation Instructions (l 2, 3 and 30, 31)

The installation work should be done by a qualified installation specialist.

Before commencing work, carefully read these installation instructions and the operating instructions to ensure that installation is performed correctly. (Please keep these instructions. You may need them when maintaining or moving this unit.)

Model number suffix “EB” denotes UK model.

TQBJ0981

Caution for AC Mains Lead

Figure A Figure B

Fuse cover

Figure A

Fuse (5 ampere)

Figure B

Fuse (5 ampere)

(For the AC mains plug of three pins)

For your safety, please read the following text carefully. This appliance is supplied with a moulded three pin

mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark Ï or the BSI mark Ì on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local dealer.

Before use

Remove the connector cover.

How to replace the fuse

The location of the fuse differ according to the type of AC mains plug (figures A and B). Confirm the AC mains plug fitted and follow the instructions below. Illustrations may differ from actual AC mains plug.

1. Open the fuse cover with a screwdriver.

2. Replace the fuse and close or attach the fuse cover.

Safety precautions

WARNING

Unit

≥ To reduce the risk of fire, electric shock or product damage,

– Do not expose this unit to rain, moisture, dripping or

splashing.

– Do not place objects filled with liquids, such as vases, on

this unit. – Use only the recommended accessories. – Do not remove covers. – Do not repair this unit by yourself. Refer servicing to

qualified service personnel. – Do not let metal objects fall inside this unit. – Do not place heavy items on this unit.

AC mains lead

≥ To reduce the risk of fire, electric shock or product damage,

– Ensure that the power supply voltage corresponds to the

voltage printed on this unit. – Insert the mains plug fully into the socket outlet. – Do not pull, bend, or place heavy items on the lead. – Do not handle the plug with wet hands. – Hold onto the mains plug body when disconnecting the

plug. – Do not use a damaged mains plug or socket outlet.

≥ The mains plug is the disconnecting device.

Install this unit so that the mains plug can be unplugged from the socket outlet immediately.

CAUTION

Unit

≥ This unit utilizes a laser. Use of controls or adjustments or

performance of procedures other than those specified herein may result in hazardous radiation exposure.

≥ Do not place sources of naked flames, such as lighted

candles, on this unit.

≥ This unit may receive radio interference caused by mobile

telephones during use. If such interference occurs, please increase separation between this unit and the mobile telephone.

≥ This unit is intended for use in moderate climates.

Placement

≥ Place this unit on an even surface. ≥ To reduce the risk of fire, electric shock or product damage,

– Do not install or place this unit in a bookcase, built-in

cabinet or in another confined space. Ensure this unit is

well ventilated. – Do not obstruct this unit’s ventilation openings with

newspapers, tablecloths, curtains, and similar items. – Do not expose this unit to direct sunlight, high

temperatures, high humidity, and excessive vibration.

TQBJ0981

Battery

≥ Danger of explosion if battery is incorrectly replaced.

Replace only with the type recommended by the manufacturer.

≥ Mishandling of batteries can cause electrolyte leakage and

may cause a fire. – Remove the battery if you do not intend to use the remote

control for a long period of time. Store in a cool, dark

place. – Do not heat or expose to flame. – Do not leave the battery(ies) in a car exposed to direct

sunlight for a long period of time with doors and windows

closed. – Do not take apart or short circuit. – Do not recharge alkaline or manganese batteries. – Do not use batteries if the covering has been peeled off.

≥ When disposing of the batteries, please contact your local

authorities or dealer and ask for the correct method of disposal.

Table of contents

Caution for AC Mains Lead.............................. 2

Safety precautions............................................ 2

Accessories....................................................... 3

Control reference guide ................................... 4

Using the remote control ................................. 5

Connections ...................................................... 6

Inserting media .................................................7

Network settings............................................... 8

Streaming music over the network ............... 11

Bluetooth About Bluetooth

Media playback controls ................................ 16

Listening to DAB/DAB+.................................. 18

Listening to FM radio ..................................... 20

Sound adjustment .......................................... 21

Clock and Timer.............................................. 21

Firmware updates ........................................... 22

Others .............................................................. 23

Troubleshooting.............................................. 25

Licenses .......................................................... 27

Unit and media care........................................ 28

Playable media................................................ 28

Specifications..................................................29

Attaching the unit to a wall (optional)........... 30

Limited Warranty (ONLY FOR AUSTRALIA)......46

operations .................................... 14

............................................ 15

About descriptions in these operating instructions

≥ Pages to be referred to are indicated as “l ±±”. ≥ Unless otherwise indicated, operations are described using

the remote control. You can also use the controls on this unit if they are the same.

Accessories

Check the supplied accessories before using this unit.

∏ 1 Remote control

(N2QAYB001139)

∏ 1 Battery for remote control

∏

(For the United Kingdom and Ireland

1 AC mains lead

(For the black model: K2CT2YY00127) (For the silver model: K2CT2YY00126) (For the blue model: K2CT2YY00127) (For the red model: K2CT2YY00127)

∏ (For Continental Europe)

1 AC mains lead

(For the black model: K2CQ2YY00153) (For the silver model: K2CQ2YY00154) (For the blue model: K2CQ2YY00153)

∏ (For Australia and New Zealand)

1 AC mains lead

(K2CJ2YY00116)

∏ 1 DAB indoor antenna

(N1CYYYY00022)

Wall mounting accessories

∏ 1 Safety holder

(TPBDA004)

∏ 2 Wall mount

∏ 1 Wall mounting sheet

≥ Use this sheet for wall mounting.

(l 30)



≥ Do not use AC mains lead with other equipment. ≥

Product numbers provided in these operating instructions are correct as of December 2016. These may be subject to change.

)

brackets

(RSC1262-1)

The symbols on this product (including the accessories) represent the following:

AC DC Class II equipment (The construction of the product is double-insulated.)

IOn

Í Standby

TQBJ0981

Control reference guide

789

10 11

Top view

1 USB port (l 7) 2 AUX IN jack (l 6) 3 Standby/on switch (Í/I)

Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power.

4 Select the audio source

On this unit:

“CD” ----------. “DAB+” -----------. “FM” -----------. “AUX”

“NETWORK” (------ “BLUETOOTH” (------ “USB”

≥ Press and hold to enter pairing mode (l 14) or

disconnect a Bluetooth

On the remote control:

[ ]: “BLUETOOTH” [CD/USB]: “CD” ,. “USB”

[RADIO, EXT-IN]: “DAB+” -"-. “FM” -"-. “AUX”

5 Basic playback control buttons

TQBJ0981

device (l 15).

^"" “NETWORK”("}

6 Adjust the volume (0 (min) to 50 (max)) 7 FAVOURITE buttons for storing or selecting radio

station ([1] to [5]) (l 13, 18, 20)

8 Set wall mount mode 9 Select D.BASS 10 Adjust surround 11 Open or close the sliding door 12 Display 13 Sliding door 14 Remote control signal sensor

Distance: Within approx. 7 m directly in front Angle: Approx. 30o left and right

15 Network indicator 16 Speakers

These speakers do not have magnetic shielding. Do not place them near a TV, personal computer or other magnetic devices.

EXT-IN

27 28

(Alkaline or manganese battery)

17 Turn the unit on or off 18 Select number

≥ To select a 2-digit number

Example: 16: [S10]

≥ To select a 3-digit number

Example: 124: [S10]

> [1] > [6]

> [S10] >[1] > [2]> [4]

19 Delete a programmed track 20 Enter sound menu 21 Set the play menu item 22 Change the displayed information 23 Clock and timer operation 24 Set the programme function 25 Mute the sound

Press again to cancel. “MUTE” is also cancelled when the volume is adjusted or the unit is turned off.

26 Select preset EQ 27 Enter setup menu 28 Set the radio menu item 29 Selection/OK 30 Dim the display panel and indicator

Press again to cancel.

Using the remote control

Insert the battery so the terminals (i and j) match those in the remote control.

R6/LR6, AA

Point it at the remote control signal sensor on this unit.

≥ To avoid interference, please do not put any objects in front

of signal sensor.

TQBJ0981

Connections

Connect the antenna.

This unit can receive DAB/DAB+ and FM stations with the DAB antenna.

Adhesive tape (not supplied)

DAB indoor antenna (supplied)

Be sure to tighten the nut fully.

To a mains socket

AC mains lead (supplied)

Connect the AC mains lead after all other connections are completed.

This unit consumes a small amount of AC power (l 29) even when turned off.

≥ In the interest of energy conservation, if you will not be using this unit for an extended period of time,

unplug it from the mains socket.

≥ Some settings will be lost after you disconnect the system. You have to set them again.

Audio cable (not supplied)



≥ Tape the antenna to a wall or column in a position with the least amount of interference. ≥ If radio reception is poor, use a DAB outdoor antenna (not supplied).

Connect an external music device

1 Connect an external music device using an audio

cable (not supplied).

≥ Plug type: ‰3.5 mm stereo

2 Press [RADIO, EXT-IN] repeatedly to select “AUX”

and start playback on the connected device.

∫ To select the sound input level of the

external device

1 While in AUX mode, press [SOUND] repeatedly to

select “INPUT LEVEL”.

2 Press [2, 1] to select “NORMAL” or “HIGH” and

then press [OK].

≥ The factory default is “NORMAL”.



≥ To improve sound distortion when “HIGH” is selected, select “NORMAL”. ≥ Switch the equalizer off or turn the volume of the external device down to reduce the input signal. High level of input signal will

distort the sound.

≥ For details, refer to the operating instructions of the device.

TQBJ0981

Inserting media

≥ Make sure to tilt the disc so as not to touch the sliding

door.

≥ Do not open the sliding door manually.

The label side

∫ Connecting a USB device

≥ Insert the USB device directly. Do not use any USB extension cable. ≥ Please disconnect the USB device if you finish using. ≥ Before removing the USB device, select a source other than “USB”.

∫ Inserting a CD

USB cable (not supplied)

To the compatible device

∫ Charging a device

Charging starts when a device (rated value: 5 V/1.5 A) is connected to the USB port of this unit.

1 Turn the unit on. 2 Connect a device.

{. Confirm from the screen of the connected device, etc. to

make sure charging has started.



≥ Make sure that the unit does not fall when inserting or removing media. ≥ When moving this unit, be sure to remove all media and turn this unit to standby mode.

≥ A cable compatible with your device is required. Use the

cable that comes with your device.

≥ Even if you connect a cable compatible with the USB port of

this unit, your device may not be charged. In that case, use the charger that comes with the device.

≥ Depending on your device, using other chargers may not

work. Check the operating instructions of your device before use.

≥ Do not connect a device with a rated value higher than 5 V/

1.5 A to this unit.

≥ To check if charging is complete, look at the screen of the

connected device, etc.

≥ Once fully charged, remove the USB cable from the USB

port.

≥ After the device has started charging, you can turn the unit to

standby mode. – When charging a depleted device, do not turn the unit to

standby mode until the device becomes operational.

TQBJ0981

Network settings

Wireless LAN connection Method 1: “Using the app “Panasonic Music Streaming”” (l right)

• You can make the wireless network settings with the app, “Panasonic Music Streaming” (free of charge).

Method 2: “Using an Internet browser” (l 9)

• You can access this unit’s network settings from the Internet browser on your smartphone or PC, etc.

Method 3: “Using WPS (Wi-Fi Protected Setup

)” (l 10)

• If your wireless router supports WPS, you can set up a connection by either pressing the WPS button, or entering the WPS PIN code.

Wired LAN connection Method 4: “Using a LAN cable” (l 10)

• You can make a stable connection to the network with a LAN cable.

You can stream music from an iOS device (iPhone/ iPad/iPod), an AndroidTM device or a PC (Windows) to this system’s speakers by using the Qualcomm® AllPlayTM smart media platform. To use these features, this system must join the same network as the compatible device.

Qualcomm® AllPlayTM is a product of Qualcomm Technologies, Inc.

≥ Please update the system’s firmware after the

network settings are complete. (l 22)

Choose a network setting method from the following.

Wireless LAN connection

This system has built-in Wi-Fi® and can be connected to a wireless router.

Preparation

≥ Place this system as close to the wireless router as

possible.

≥ Do not connect a LAN cable. Doing so will disable

the Wi-Fi® function.

Method 1: Using the app “Panasonic Music Streaming”

You can also refer to the supplied “Wi-Fi® QUICK SETUP GUIDE”.

1 Download the app “Panasonic Music Streaming”

(free of charge) on your smartphone/tablet. (Always use the latest version of the app.)

≥ [iOS] : App Store ≥ [Android] : Google Play

2 Start the app and follow the on-screen

instructions.

3 Check that the connection has completed.

≥ On the unit’s display, “SUCCESS” appears when the

connection is established. (The network indicator (l 4) lights up.) – If “FAIL” is displayed press [OK], check the network

name (SSID) and the password, and then try the setting again.

The operations and on-screen display items, etc. of the app “Panasonic Music Streaming” are subject to change. For the latest information, visit

http://panasonic.jp/support/global/cs/audio/app/

(This site is in English only.)



≥ The setting will be cancelled after the set time limit. In that

case, try the setting again. To cancel this setting in the middle, press [∫].

TQBJ0981

Method 2:

Settings

Wi-Fi settings

HC1020

●●●●●●●●

Refresh list

Using an Internet browser

≥

The following explanations are based on a smartphone.

1 Turn this system on. 2 Press [RADIO, EXT-IN] on the remote control

repeatedly to select “NETWORK”.

3 To enter “SETTING” mode

1 Press [SETUP] on the remote control repeatedly to

select “NET SETUP” and then press [OK].

2Press [2, 1] on the remote control to select

“MANUAL” and then press [OK].

3Press [2, 1] on the remote control to select

“OK? YES” and then press [OK].

≥ After pressing [OK] to confirm “OK? YES”, the

previous network connection you have set with this unit will be cleared.

≥ Alternatively, while pressing and holding down [<] on

the unit, press and hold down [1/;] on the unit for at least 4 seconds.

“SETTING” blinks on the display.

4 Go to Wi-Fi settings on your compatible device.

5 Select “HC1020 _AJ” to connect to this

system.

≥ “  ” stands for a character that is unique to each set. ≥ This can take up to 1 minute to appear in your Wi-Fi list. ≥ If this operation does not work correctly, please repeat it

several times.

≥ Make sure that DHCP is enabled for the network setting

on your compatible device.

Select your network name (SSID) and type the password.

≥ Check the wireless router for the network name (SSID)

and the password.

≥ A list of network names (SSIDs) will be appeared when

you select the “Network Name” box.

≥ To show the characters typed in the “Password” box,

select “Show Password”.

≥ If your network requires specific settings, deselect

“DHCP” to disable DHCP. – You can use specific IP address, subnet mask,

default gateway, primary DNS, etc.

≥ To update the network name (SSID) list, select “Refresh

list”.

8 Select “Connect” to apply the settings.

≥ On the unit’s display, “SUCCESS” appears when the

connection is established. (The network indicator (l 4) lights up.) – If “FAIL” is displayed press [OK], check the network

name (SSID) and the password, and then try the setting again.

≥ Depending on the device, the connection complete

screen may not be displayed.

9 Make sure to connect your compatible device back

to your home wireless network.



≥ Enable Java and Cookies in your browser settings.

About the network setting page:

iOS device: The settings page will be automatically displayed in the Internet browser. Except iOS device: Open the Internet browser and refresh the page to display the settings page. ≥ If the settings page is not displayed, type

“http://172.19.42.1/” into the URL address field.

6 Type a device name and then select “Next”.

≥ The device name will be displayed as this system’s

name on the network.

≥ Maximum characters that can be shown: 32 ≥ Emoji characters are not supported. ≥ The device name is set when “Next” is selected. ≥ You can also change the device name after the network

connection is set up. (l 11, “To make network-related settings”)

TQBJ0981

Method 3:

e.g.,

LAN cable (not supplied)

Broadband router, etc.

e.g.,

Using WPS (Wi-Fi Protected Setup

A compatible wireless router may have the WPS identifier mark.

1 Turn this system on. 2 Press [RADIO, EXT-IN] on the remote control

repeatedly to select “NETWORK”.

3 To enter “WPS PUSH” mode

1 Press [SETUP] on the remote control repeatedly to

select “NET SETUP” and then press [OK].

“WPS PUSH” is indicated on the display.

2 Press [OK]. 3Press [2, 1] on the remote control to select “OK?

YES” and then press [OK].

≥ Alternatively, while pressing and holding down [<] on

the unit, press and hold down [5/9] on the unit for at least 4 seconds.

≥

If the unit is already connected to a wireless LAN network, “NETWORK INITIALIZING” is displayed for about 1 minute.

“WPS” flashes on the display.

4 Activate the WPS button on the wireless router.

≥ On the unit’s display, “SUCCESS” appears when the

connection is established. (The network indicator (l 4) lights up.) – “FAIL” may be displayed if the connection was not

made within the set time limit. Press [OK] setting again. If “FAIL” is still displayed, try other methods.

∫ Using the WPS PIN code

1 Turn this system on. 2 Press [RADIO, EXT-IN] on the remote control

repeatedly to select “NETWORK”.

3 To enter “WPS PIN” mode

1 Press [SETUP] on the remote control repeatedly to

select “NET SETUP” and then press [OK].

2Press [2, 1] on the remote control to select “WPS

PIN” and then press [OK].

≥ Alternatively, while pressing and holding down [<] on

the unit, press and hold [:/6] on the unit for at least 4 seconds.

≥

If the unit is already connected to a wireless LAN network, “NETWORK INITIALIZING” is displayed for about 1 minute.

The PIN code is indicated on the display.

4 Enter the PIN code into the wireless router.



≥ Once the system enters WPS PIN code mode, you cannot

set up using the WPS button. To use the WPS button, turn the system off and then on, and redo the network settings.

≥ Depending on a router, other connected devices may

temporarily lose their connection.

≥

For details, refer to the operating instructions of the wireless router.

TQBJ0981

)

. Try the

Wired LAN connection

Method 4: Using a LAN cable

1 Disconnect the AC mains lead. 2 Connect the unit to a broadband router, etc. using

a LAN cable.

3 Connect the AC mains lead to the unit and turn

this system on.

≥ When the connection is established, the network

indicator (l 4) lights up.



≥ Use category 5 or above straight LAN cables (STP) when

connecting to peripheral devices.

≥ The LAN cable must be connected or disconnected while the

AC mains lead is disconnected.

≥ Inserting any cable other than a LAN cable in the LAN port

can damage the system.

≥ If the LAN cable is disconnected, the network-related

settings (l 11) will be initialized. In that case, make the settings again.

≥ When a LAN cable is connected, the Wi-Fi function will be

disabled.

To make network-related settings

You can change this system’s name on the network, and use specific IP address, subnet mask, default gateway, primary DNS, etc.

You can also change the name of this system by changing a setting in the app “Panasonic Music Streaming” (l right). For details on the app, refer to the site below.

http://panasonic.jp/support/global/cs/audio/app/

(This site is in English only.)

Preparation

≥ Complete the network settings. (l 8) ≥ Connect your device to the same network as this

system.

≥ Check this system’s IP address (l 24), and note it

down.

1 Start an Internet browser on your device and then

type this system’s IP address into the address field to display the settings page.

≥ It may take a few minutes until the settings page is

displayed depending on the environment. In that case, reload the browser.

≥ If the unit is connected with Wi-Fi, only a device name

can be changed. Close the settings page after changing the device name. – To change the device name, select “Change”, and

type a new device name, and then select “Apply”.

2 Type a device name and then select “Next”.

≥ Refer to the step 6 of “Using an Internet browser” (l 9)

for details on a device name.

3 Select and input the details.

≥ If your network requires specific settings, deselect

“DHCP” to disable DHCP. – You can use specific IP address, subnet mask,

default gateway, primary DNS, etc.

4 Select “Connect” to apply the settings.

≥ When the connection is established, “SUCCESS”

appears on the unit’s display.

Streaming music over the network

You can stream music from your devices or online music services to this system’s speakers and other speakers powered by AllPlay. You can also stream music source of this system to other speakers powered by AllPlay.

Streaming music on network devices

You can use the AllPlay function to stream music from the device on the network to this system’s speakers by using the app “Panasonic Music Streaming” (free of charge), etc.

≥

[iOS]

: App Store

≥

[Android]

: Google Play

The operations and on-screen display items, etc. of the app “Panasonic Music Streaming” are subject to change. For the latest information, visit

http://panasonic.jp/support/global/cs/audio/app/

More apps are available. For details, visit

www.panasonic.com/global/consumer/homeav/ allseries/service

(These sites are in English only.)

Preparation

≥ Complete the network settings. (l 8) ≥ Connect the following devices to the same network

as this system. – Device with “Panasonic Music Streaming”, etc.

installed

– Device containing music

The following steps are based on “Panasonic Music Streaming”.

1 Turn this system on.

≥ Check that the network indicator (l 4) lights up. ≥ If it does not light up, check the network settings. (l 8)

2 Start the app “Panasonic Music Streaming”.

≥ Always use the latest version of the app.

3 From “Speaker”, select this system as the output

speakers.

≥ If you have multiple speakers powered by AllPlay, you

can enjoy synchronised sound from them. To group speakers, drag e.g., “ ” of the desired speakers over each other. – You can also play different songs on other speakers

– The number of speakers powered by AllPlay that can

perform playback at the same time differs depending on the situation of use.

– When you turn off one of the speakers powered by

AllPlay, other speakers in the same group may stop the playback.

4 Select a music source. 5 Select a song.

TQBJ0981



≥ This system will be displayed as “Panasonic HC1020” if the

device name is not set.

≥ When playing back music from the DLNA server (PC with

Windows 7 or later installed, smartphone, Network Attached Storage (NAS) device, etc.), add the contents and folder to the libraries of the Windows Media or the NAS device, etc.

≥ Playlist of Windows Media

contents that are stored in the libraries.

≥ About supported format, refer to “Specifications” (l 29).

– File formats that are not supported by your DLNA server

cannot be played.

≥ Depending on the contents and the connected equipment,

playback may not be performed properly.

≥ Ensure to stop playback on your device before turning it off.

Player, the smartphone,

Player can play back only the

Streaming online music

This system is compatible with several online music services. Visit the following website for the compatibility information.

www.panasonic.com/global/consumer/homeav/ allseries/service

Preparation

≥ Make sure that the network is connected to the

Internet.

≥ Connect a device with a compatible app installed to

the same network as this system.

1 Turn this system on.

≥ Check that the network indicator (l 4) lights up. ≥ If it does not light up, check the network settings. (l 8)

2 Start the app, and select a song to playback.

∫ Using Spotify

You will need Spotify Premium. For details, visit the following website.

www.spotify.com/connect/ After step 2

3 Select the square image of the song’s cover art in

the bottom left of the playback screen.

4 From “ ”, select this system as the output

speakers.

≥ To enjoy synchronised sound from the multiple

speakers powered by AllPlay, you need to group the speakers using the app “Panasonic Music Streaming”. (l 11 )

∫

Using online music services other than Spotify

After step 2

From “ ”, select this system as the output speakers.

≥ Depending on the service, you might need to open full

screen player to display “ ”.

≥ If you have multiple speakers powered by AllPlay, you

can enjoy synchronised sound from them. Select “Group” and then select the speakers to group.

TQBJ0981



≥ This system will be displayed as “Panasonic HC1020” if the

device name is not set.

≥ Registration/subscription is required. ≥ Fees may apply. ≥ Services, icons, and specifications are subject to change. ≥ For details, visit the individual music service’s website.

Streaming music on this system Storing stations under (FAVOURITE)

You can use the app “Panasonic Music Streaming” (l 11) to stream this system’s music source (radio/CD/ Bluetooth®/AUX/USB source) to other speakers powered by AllPlay.

Preparation

≥ Complete the network settings. (l 8) ≥ Prepare the desired audio source on this system

(e.g. insert a CD, etc.)

≥ Install the app “Panasonic Music Streaming” on your

device.

≥ Connect your device and your speakers powered by

AllPlay to the same network as this system.

1 Turn this system on.

≥

Check that the network indicator

≥ If it does not light up, check the network settings. (l 8)

(l 4

) lights up.

2 Start the app “Panasonic Music Streaming”.

≥ Always use the latest version of the app.

3 From “Speaker”, select the speaker to stream this

system’s audio.

≥ To stream this system’s audio to other speakers

4 Select your desired music source from the list. 5 Select this system.

The device will start to read the selected music source’s information from this system.

≥ This system will change to the selector mode for the

selected music source.

≥ The speaker selected in step 3 and this system will be

automatically grouped together.

≥ Depending on the selected music source, playback may

start. If a content list appears on your device, select the desired content to start playback.

≥ The number of speakers powered by AllPlay that can

perform playback at the same time differs depending on the situation of use.

≥ When you turn off one of the speakers powered by

AllPlay, other speakers in the same group may stop the playback.



≥ This system will be displayed as “Panasonic HC1020” if the

device name is not set.

≥ When enjoying video contents with this function, the video

and audio output may not be synchronised.

[1] to [5] (Only when playback using internet radio app)

This unit is compatible with the Qualcomm® AllPlayTM Radio powered by TuneIn. You can preset stations when playback using internet radio app “AllPlay Radio”.

Qualcomm product of Qualcomm Technologies, Inc.

You can store up to 5 stations under (FAVOURITE) [1] to [5]. ≥ A station previously stored is overwritten when

another station is stored under the same (FAVOURITE) [1] to [5].

Preparation

≥ Make sure that the network is connected to the

Internet.

≥ Connect a device with an “AllPlay Radio” app

installed to the same network as this system.

AllPlayTM Radio powered by TuneIn is a

1 Turn this system on.

≥ Check that the network indicator (l 4) lights up. ≥ If it does not light up, check the network settings. (l 8)

2 Start the app “AllPlay Radio”, and select a station

to playback.

≥ Always use the latest version of the app.

3 Press and hold one of [1] to [5] until “P ” appears

on the display. (“  ” stands for a number.)

∫ Listening to a stored station

Press one of [1] to [5].



≥ If the selected preset channel has not been preset, “NO

PRESET” is displayed.

TQBJ0981

Bluetooth® operations

You can listen to the sound from the Bluetooth® audio device from this unit wirelessly. ≥ Refer to the operating instructions of the Bluetooth

device for details.

Connecting via Bluetooth® menu

Preparation

≥ Turn on the Bluetooth

place the device near this unit.

feature of the device and

∫ Pairing with Bluetooth® devices

1 Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to step 3.

2 Press [PLAY MENU] to select “PAIRING” and then

press [OK].

≥

Alternatively, press and hold [SELECTOR,sPAIRING] on the unit.

device.

device’s

3 Select “SC-HC1020” from the Bluetooth

Bluetooth® menu.

≥ The MAC address (e.g., 6C:5A:B5:B3:1D:0F) may be

displayed before “SC-HC1020” is displayed.

≥ The name of the connected device is indicated on the

display for a few seconds.

4 Start playback on the Bluetooth

∫ Connecting a paired Bluetooth® device

1 Press [ ] to select “BLUETOOTH”.

≥ “READY” is indicated on the display.

2 Select “SC-HC1020” from the Bluetooth

Bluetooth® menu.

≥ The name of the connected device is indicated on the

display for a few seconds.

3 Start playback on the Bluetooth

device.

device’s

Bluetooth® transmission mode

You can change the transmission mode to prioritise transmission quality or sound quality.

Preparation

≥ Press [ ] to select “BLUETOOTH”. ≥ If a Bluetooth

disconnect it.

device is already connected,

1 Press [PLAY MENU] repeatedly to select

“LINK MODE”.

2 Press [2, 1] to select the mode and then press

[OK].

MODE 1: Emphasis on connectivity MODE 2: Emphasis on sound quality



≥ Select “MODE 1” if the sound is interrupted. ≥ When enjoying video contents with this function, the video

and audio output may not be synchronised. In this case, select “MODE 1”.

≥ The factory default is “MODE 2”.



≥ If prompted for the passkey, input “0000”. ≥ You can register up to 8 devices with this unit. If a 9th device

is paired, the device that has not been used the longest will be replaced.

≥ This unit can only be connected to one device at a time. ≥ When “BLUETOOTH” is selected as the source, this unit will

automatically try and connect to the last connected

Bluetooth during this process.) If the connection attempt fails, try to establish a connection again.

device. (“LINKING” is indicated on the display

TQBJ0981

Bluetooth® input level

If the sound input level from the Bluetooth® device is too low, change the input level setting.

Preparation

≥ Connect a Bluetooth® device.

1 Press [PLAY MENU] repeatedly to select “INPUT

LEVEL”.

2 Press [2, 1] to select the level and then press

[OK]. “LEVEL 0” ,. “LEVEL i1” ,. “LEVEL i2”

^--------------------------------------------------J



≥ Select “LEVEL 0” if the sound is distorted. ≥ The factory default is “LEVEL 0”.

Disconnecting a Bluetooth® device

1 While a Bluetooth

Press [PLAY MENU] repeatedly to select “DISCONNECT?”.

device is connected:

2 Press [2, 1] to select “OK? YES” and then press

[OK].



≥ You can also disconnect the Bluetooth® device by pressing

and holding [SELECTOR, s PAIRING] on the unit.

≥ The Bluetooth

audio source (e.g., “CD”) is selected.

device will be disconnected if a different

About Bluetooth

Panasonic bears no responsibility for data and/or information that is compromised during a wireless transmission.

∫ Frequency band used

≥ This system uses the 2.4 GHz frequency band.

∫ Certification of this device

≥ This system conforms to frequency restrictions and

has received certification based on frequency laws. Thus, a wireless permit is not necessary.

≥ The actions below are punishable by law in some

countries: – Taking apart or modifying the system. – Removing specification indications.

∫ Restrictions of use

≥ Wireless transmission and/or usage with all

Bluetooth® equipped devices is not guaranteed.

≥ All devices must conform to standards set by

Bluetooth SIG, Inc.

≥ Depending on the specifications and settings of a

device, it can fail to connect or some operations can be different.

≥ This system supports Bluetooth® security features.

But depending on the operating environment and/or settings, this security is possibly not sufficient. Transmit data wirelessly to this system with caution.

≥ This system cannot transmit data to a Bluetooth®

device.

∫ Range of use

≥ Use this device at a maximum range of 10 m. The

range can decrease depending on the environment, obstacles or interference.

∫ Interference from other devices

≥ This system may not function properly and troubles

such as noise and sound jumps may arise due to radio wave interference if this system is located too close to other Bluetooth® devices or the devices that use the 2.4 GHz band.

≥ This system may not function properly if radio waves

from a nearby broadcasting station, etc. is too strong.

∫ Intended usage

≥ This system is for normal, general use only. ≥ Do not use this system near an equipment or in an

environment that is sensitive to radio frequency interference (example: airports, hospitals, laboratories, etc).

TQBJ0981

+ 33 hidden pages