PANASONIC PV-GS69, PV-GS39, PV-GS29 Diagram
Digital Video Camcorder
Operating Instructions
(PV-GS69 Shown)
Models No.
PV-GS69
PV-GS39
PV-GS29
Before attempting to connect, operate or adjust this product, please
read these instructions thoroughly.
PL
LSQT1070 A
Things You Should Know
Thank you for choosing Panasonic!
You have purchased one of the most
sophisticated and reliable products on the market
today. Used properly, we’re sure it will bring you
and your family years of enjoyment. Please take
time to fill in the information on the right.
The serial number is on the tag located on the
underside of your Camcorder. Be sure to retain
this manual as your convenient Camcorder
information source.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
Safety Precautions
WARNING :
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
Your
mode.
It is recommended that only cassette tapes that have been tested and inspected for use in Camcorders
with the mark be used.
Camcorder is designed to record and play back in Standard Play (SP) mode and Long (LP)
This symbol warns the user that uninsulated
voltage within the unit may have sufficient
magnitude to cause electric shock. Therefore,
it is dangerous to make any kind of contact
with any inside part of this unit.
This symbol alerts the user that important
literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in order
to avoid any problems.
The above markings are located on the appliance bottom cover.
CAUTION:
TO PREVENT FIRE OR SHOCK HAZARD AND ANNOYING
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
CAUTION:
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.
• Since this product gets hot during use, operate it in a well ventilated place; do not install this
equipment in a confined space such as a bookcase or similar unit.
WARNING
AS WITH ANY SMALL OBJECT, SD CARDS CAN BE SWALLOWED BY YOUNG CHILDREN.
DO NOT ALLOW CHILDREN TO HANDLE THE SD CARD.
2
- U.S.A. CONSUMERS Only-
Declaration of Conformity
Trade Name : Panasonic
Model No. : PV-GS29/PV-GS39/PV-GS69
Responsibility Party : Panasonic Corporation of North America
Address : One Panasonic Way Secaucus New Jersey 07094
Telephone Number : 1-800-211-PANA(7262)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Note:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
To assure continued compliance, follow the attached installation instructions and use only shielded
interface cables when connecting to computer or peripheral devices.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
06'306'3
06'3
U.S.A. CONSUMERS: ATTENTION:
A lithium ion/polymer battery that is recyclable powers the product you
have purchased. Please call 1-800-8-BATTERY for information on how
to recycle this battery.
3
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or the table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when it will be left unused for long
periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
4
Precautions
USE & LOCATION
WARNING
● TO AVOID SHOCK HAZARD ... Your
Camcorder and power supply should not be
exposed to rain or moisture. Do not connect the
power supply or operate your Camcorder if it
gets wet. Your Camcorder has been designed
for outdoor use, however it is not designed to
sustain direct exposure to water, rain, sleet,
snow, sand, dust, or a direct splashing from a
pool or even a cup of coffee. This action could
permanently damage the internal parts of your
Camcorder. Do not attempt to disassemble this
unit. There are no user serviceable parts inside.
Unplug your Camcorder from the power supply
before cleaning.
CAUTION
● DO NOT AIM YOUR CAMCORDER AT
THE SUN OR OTHER BRIGHT OBJECTS
● DO NOT LEAVE THE CAMCORDER
WITH THE EVF AIMED DIRECTLY
AT THE SUN AS THIS MAY CAUSE
DAMAGE TO THE INTERNAL PARTS OF
THE EVF
● DO NOT EXPOSE YOUR CAMCORDER
TO EXTENDED HIGH TEMPERATURE
... Such as, in direct sunlight, inside a closed
car, next to a heater, etc... This action could
permanently damage the internal parts of your
Camcorder.
● AVOID SUDDEN CHANGES IN
TEMPERATURE ...
moved from a cold place to a warm place,
moisture may form on the tape and inside the
unit.
DO NOT LEAVE YOUR CAMCORDER
●
If the unit is suddenly
OR THE POWER SUPPLY TURNED ON
WHEN NOT IN USE.
● STORAGE OF YOUR CAMCORDER ...
Store and handle your Camcorder in a manner
that will not subject it to unnecessary movement
(avoid shaking and striking). Your Camcorder
contains a sensitive pick-up device which could
be damaged by improper handling or storage.
CARE
● TO CLEAN YOUR CAMCORDER ... Do
not use strong or abrasive detergents when
cleaning your Camcorder body.
● TO PROTECT THE LENS ... Do not touch
the surface of the lens with your hand. Use
a commercial Camcorder lens solution and
lens paper when cleaning the lens. Improper
cleaning can scratch the lens coating.
● TO PROTECT THE FINISH OF YOUR
CAMCORDER ... Before handling your
Camcorder, make sure your hands and face
are free from any chemical products, such as
suntan lotion, as it may damage the finish.
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited
viewing.
This product incorporates copyright protection technology that is protected by method claims of
certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
- If you see this symbol -
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and
ask for the correct method of disposal.
5
End User License Agreement (for USB Driver, MotionDV STUDIO and
Quick Movie Magic)
Before opening the CD-ROM package (PV-GS69 Only), please read the following.
You (“Licensee”) are granted a license for the Software defined in this End User Software Agreement
(“Agreement”) on condition that you agree to the terms and conditions of this Agreement. If Licensee
does not agree to the terms and conditions of this Agreement, promptly return the Software to
Matsushita Electric Industrial Co., Ltd. (“Matsushita”), its distributors or dealers from which you made
the purchase.
Article 1 License
Licensee is granted the right to use the software, including the information recorded or described on
the CD-ROM, instruction manuals, and any other media provided to Licensee (collectively “Software”),
but all applicable rights to patents, copyrights, trademarks and trade secrets in the Software are not
transferred to Licensee.
Article 2 Use by a Third Party
Licensee may not use, copy, modify, transfer or allow any third party, whether free of charge or not, to
use, copy or modify the Software, except as expressly provided for in this Agreement.
Article 3 Restrictions on Copying the Software
Licensee may make a single copy of the Software in whole or in part solely for back-up purpose.
Article 4 Computer
Licensee may only use the Software on a single computer at a single location.
Article 5 Reverse Engineering, Decompiling or Disassembly
Licensee may not reverse engineer, decompile, or disassemble the Software, except to the extent either
of them is permitted under law or regulation of the country where Licensee resides. Matsushita, or its
distributors or dealers will not be responsible for any defects in the Software or damage to Licensee
caused by Licensee’s reverse engineering, decompiling, or disassembly of the Software.
Article 6 Limitation of Liability
The Software is provided “AS-IS” without warranty of any kind, either expressed or implied, including,
but not limited to, warranties of non-infringement, merchantability and/or fitness for a particular purpose.
Further, Matsushita does not warrant that the operation of the Software will be uninterrupted or error
free. Matsushita or any of its distributors or dealers will not be liable for any damage suffered by
Licensee arising from or in connection with Licensee’s use of the Software.
Article 7 Export Control
Licensee agrees not to export or re-export to any country the Software in any form without the
appropriate export licenses under regulations of the country where Licensee resides, if necessary.
Article 8 Termination of License
The right granted to Licensee hereunder will be automatically terminated if Licensee violates any of the
terms and conditions of this Agreement. Upon such automatic termination, Licensee must destroy the
Software and related documentation together with all the copies thereof at Licensee’s own expense.
6
Differences between models
This operating instruction book is designed for use with models PV-GS29, PV-GS39 and PV-GS69. The
PV-GS69 is the model used for illustrative purposes. Features may vary, so please read carefully.
Model Number PV-GS29 PV-GS39 PV-GS69
Battery Pack
(Supplied)
CD-ROM – – Supplied (LSFT0648)
USB Cable – Supplied (K1HA05CD0014) Supplied (K1HA05CD0014)
Card Feature No Yes Yes
Monitor 2.5-inch LCD 2.7-inch Wide LCD 2.7-inch Wide LCD
USB Jack* No Yes (Full-Speed) Yes (High-Speed)
Audio Dubbing No No Yes
Recording a Still
Picture on a Tape
Cinema Function Yes No No
Wide/4:3 Function No Yes Yes
Remote Control
Sensor
* It is only compatible with USB 2.0 PCI Card and/or connection.
CGR-DU06
(640 mAh)
Yes No No
No No Yes
CGR-DU06
(640 mAh)
CGA-DU12
(1 150 mAh)
How to Turn off the Demo Mode
To terminate the demonstration mode, insert a cassette or set the [ DEMO MODE] to
[OFF] as follows.
1 Set [ SETUP] >> [ DEMO MODE] >> [OFF].
7
With a PC (Operating System Compatibility Chart)
Before using the PC function (pp. 56~69), please refer to the OS (operating system) compatibility chart,
below.
For Windows
Model
Number
PV-GS29
PV-GS39
PV-GS69
Windows OS Built-in SD Drive Web Camera
Windows 2000 – – –
Windows XP – – –
Windows 2000 Yes* Yes (SP4 or later) –
Windows XP Yes* Yes (SP2 or later)* –
Windows 2000 Yes* Yes (SP4 or later) Yes (SP4 or later)
Windows XP Yes* Yes (SP1 or later) Yes (SP2 or later)
MotionDV STUDIO/
Quick Movie Magic
For Macintosh
Model
Number
PV-GS29 X v 10.1 - v 10.4 – – –
PV-GS39 X v 10.1 - v 10.4 Yes* – –
PV-GS69 X v 10.1 - v 10.4 Yes* – –
* The USB equipment operates with the driver installed standard on your OS.
Macintosh OS Built-in SD Drive Web Camera
MotionDV STUDIO/
Quick Movie Magic
For Macintosh (DV connection)
Model
Number
PV-GS29 X v 10.3 - v 10.4 Yes
PV-GS39 X v 10.3 - v 10.4 Yes
PV-GS69 X v 10.3 - v 10.4 Yes
Macintosh OS iMovie/iMovieHD
8
Contents
Before Using
Things You Should Know .......................................2
Safety Precautions .................................................2
Precautions .............................................................5
End User License Agreement ................................. 6
Differences between models ..................................7
With a PC (Operating System Compatibility Chart)
................................................................................8
Quick Guide ..........................................................10
Standard Accessories ........................................... 12
Parts Identification and Handling ..........................12
The Remote Control (PV-GS69 Only : Optional) ..14
Power Supply .......................................................15
Charging Time and Available Recording Time .....16
To Use as a Grip Belt ...........................................17
Re-attaching the Lens Cap ...................................18
Attaching the Shoulder Strap ................................ 18
Inserting/Removing a Cassette ............................18
Using a Memory Card (Optional)
(For PV-GS39/PV-GS69) ....................................20
Turning on the Camcorder .................................... 21
Setting Date and Time ..........................................21
Using the Viewfinder/LCD Monitor .......................22
Easy to Use Mode Dial .........................................23
How to Use the Joystick Control ........................... 23
Using the Menu Screen ........................................26
Selecting Language ..............................................27
List of Menus ........................................................27
LP Mode ...............................................................30
Recording Mode
About Recording ...................................................31
Recording on a Tape ............................................31
To Check the Recording .......................................32
Finding the End of Recording
(Blank Search Function) .....................................32
Recording a Still Picture on a Tape
(PV-GS29 Only) .................................................. 33
Recording a Still Picture on a Card (Photoshot)
(For PV-GS39/PV-GS69) ....................................33
Recording Yourself ...............................................35
Recording with the Built-in LED Video Light .........35
Quick Start ............................................................35
Self-timer Recording (For PV-GS39/PV-GS69) .... 36
Zoom In/Out Functions .........................................37
Digital Zoom Function ........................................... 37
Image Stabilizer Function .....................................38
Fade In/Out Functions ..........................................38
Backlight Compensation Function ........................39
MagicPix Function ................................................40
Soft-Skin Mode .....................................................40
Wind Noise Reduction Function ...........................41
Cinema Function (PV-GS29 Only) .......................41
Wide/4:3 Function (For PV-GS39/PV-GS69) .......41
Recording in Special Situations (Scene Mode) ....42
Recording in Natural Colors (White Balance) .......43
Manual Shutter Speed Adjustment .......................45
Manual Iris Adjustment (F Number) ...................... 45
Manual Focus Adjustment ....................................46
Playback Mode
Playing Back a Tape ............................................. 47
Finding a Scene You Want to Play Back ..............48
Slow Motion Playback (PV-GS69 Only) ...............48
Still Playback/Still Advance Playback ...................49
Playing Back a Memory Card
(For PV-GS39/PV-GS69) ....................................49
Slide Show (For PV-GS39/PV-GS69) ..................50
Deleting the Files Recorded on a Card
(For PV-GS39/PV-GS69) ....................................51
Writing Printing Data on a Card (DPOF Setting)
(For PV-GS39/PV-GS69) ....................................52
Protecting the Files on a Card (Lock Setting)
(For PV-GS39/PV-GS69) ....................................52
Formatting a Card (For PV-GS39/PV-GS69) .......53
Playing Back on Your TV ...................................... 53
Editing Mode
Recording from a Tape onto a Card
(For PV-GS39/PV-GS69) ....................................55
Audio Dubbing (PV-GS69 Only) ...........................55
Copying onto a DVD Recorder or a VCR
(Dubbing) ............................................................56
Using the DV Cable for Recording
(Digital Dubbing) .................................................56
PC Connection With DV Interface Cable ..............57
With a PC
Using Camcorder with a PC .................................58
Using the USB Function ......................................58
To disconnect USB cable safely ...........................61
Using as a Web Camera ......................................62
Using the Motion Picture Editing Software
(PV-GS69 Only) .................................................. 66
If you no longer need software or driver
(Uninstall) ............................................................69
Transferring Motion DV Tape Pictures
(Camcorder→Macintosh) via DV Cable
(iMovie / iMovie HD) ...........................................70
Notes ....................................................................70
Others
Indications ............................................................73
Warning/Alarm Indications .................................... 74
Cautions for Use ...................................................75
Before Requesting Service
(Problems and Solutions) ...................................78
Using the RESET button ......................................81
Explanation of Terms ............................................ 82
Specifications .......................................................83
Camcorder Accessory System .............................84
Index .....................................................................85
9
Quick Guide
Using the Battery
1 Attach the Battery to the AC Adaptor and
charge it.
• Before use, fully charge the Battery.
• Since the Battery will not be charged when
the DC Cable is connected to the AC Adaptor,
disconnect it from the AC Adaptor.
• The [CHARGE] Lamp lights up, and charging
starts.
• When the [CHARGE] Lamp goes off, charging
is completed.
2 Attach the charged Battery to the
Camcorder.
Inserting a Cassette
1 Slide the [OPEN/EJECT] Lever
the front and pull up to fully open the
Cassette Compartment Cover.
• To protect the tape, if the cover is not fully
opened, the cassette holder cannot be ejected.
1
toward
2 After the Cassette Holder is opened, insert
a Cassette.
1
Inserting a Card
1 Place your Thumb on the [OPEN]
and pull the LCD Monitor 2 out in the
direction of the arrow.
2
1
2 Open the Card Slot Cover
1
Knob
3
.
3 While holding the Memory Card with its
cut corner facing right 4 insert it into the
Card Slot 5.
4 Close the Card Slot Cover
3
securely.
5
3
4
Turning on the Camcorder
• Open the LCD Monitor or extend the Viewfinder
before turning on the power.
How to Turn on the Power
1 Set the [OFF/ON] Switch to [ON] while
pressing the button 1.
• The [STATUS] Indicator lights Red.
1
How to Turn off the Power
2 Set the [OFF/ON] Switch to [OFF] while
pressing the button 1.
• The [STATUS] Indicator goes off.
1
3 Close the Cassette Holder by pressing the
[PUSH] mark 2.
4 Only after the Cassette Holder is
completely housed, close the Cassette
Compartment Cover by pressing the mark
3
.
2
10
Using the Viewfinder
Before using the Viewfinder, adjust the field of view
so that the displays inside the Viewfinder become
clear and easy to read.
1 Pull the Viewfi nder.
3
2 Adjust by turning the Eyepiece Corrector
Knob 1.
1
Playing Back a Tape
1 Set the Mode Dial to Tape Playback Mode.
• The [ TAPE PLAYBACK MODE] is displayed
on the screen.
• The One-Touch Navigation icon is displayed
on the lower right of the screen.
[One-Touch Navigation icon]
Before Using
Recording on a Tape
1 Set the Mode Dial to Tape Recording
Mode.
• The [ TAPE RECORDING MODE] is
displayed on the screen.
(PV-GS39/
PV-GS69)
(PV-GS29)
2 Press the Recording Start/Stop Button.
• Recording starts.
3 Press the Recording Start/Stop Button
again to pause the recording.
Recording a Still Picture on Card
(Photoshot)
(For PV-GS39/PV-GS69)
1 Set the Mode Dial to Card Recording
Mode.
• The [ CARD RECORDING MODE] is
displayed on the screen.
(PV-GS39/
PV-GS69)
2 Move the Joystick Control [◄]
3 Move the Joystick Control [▲]
4 Move the Joystick Control [▼]
the tape.
1
playback.
2
playback.
(PV-GS29)
3
1
to rewind
2
to start
3
to stop
Playing Back a Card
(For PV-GS39/PV-GS69)
1 Set the Mode Dial to Picture Playback
Mode.
• The [ CARD PLAYBACK MODE] is
displayed on the screen.
• The One-Touch Navigation icon is displayed
on the lower right of the screen.
[One-Touch Navigation icon]
2 Press the [PHOTO SHOT] Button.
2 Start Playback.
Joystick Control [▲] : Starting the Slide Show
Stop the Slide Show
Joystick Control [▼] : Erase the pictures
Joystick Control [◄] : Playing back the previous
picture
Joystick Control [►] : Playing back the next picture
11
Before Using
Standard Accessories
The following accessories are supplied with your
Camcorder.
1)
Parts Identification and Handling
Camcorder
2
3
4
5
6
PV-DAC14D K2CA2CA00025
K2GJ2DC00011
2) 3)
CGA-DU12
(PV-GS69
Only)
CGR-DU06
(For PV-GS29/
PV-GS39)
K2KC4CB00020
4) 5)
LSFC0018
K1HA05CD0014
(For PV-GS39/
PV-GS69)
LSFT0648
(PV-GS69 Only)
1) AC Adaptor, DC Cable and AC Cable
(pp. 15~16)
CAUTION:
This unit will operate on 110/120/220/240 V
AC. An AC plug adaptor may be required
for voltages other than 120 V AC. Please
contact either a local or foreign electrical
parts distributor for assistance in selecting an
alternate AC plug.
We recommend using the accessory power
plug adaptor (VJSS0070/KZDB4ZE00001) in
an area which has special AC outlets.
2) Battery Pack (p. 16)
3) AV Cable (pp. 53, 56)
4) Shoulder Strap (p. 18)
5) USB Cable and CD-ROM
(pp. 58, 60~61, 63, 69)
1
879
1
LCD Monitor Open Knob [OPEN] (p. 22)
2
LCD Monitor (pp. 21~23, 78)
Due to limitations in LCD production technology,
there may be some tiny bright or dark spots on the
LCD Monitor screen.
However, this is not a malfunction and does not
affect the recorded picture.
3
Card Access Lamp (p. 20)
4
Reset Button [RESET] (pp. 79, 81)
5
DC Input Jack [DC IN] (p. 16)
6
Battery Holder (p. 16)
Mode Selector Switch
7
[AUTO/MANUAL/FOCUS] (pp. 31, 42~46)
8
Card Slot Cover (p. 20)
9
Card Slot (p. 20)
13
10
11
12
A/V
15
10
Lens Hood (p. 78)
11
Lens
White Balance Sensor (p. 44)
12
14
Remote Control Sensor (PV-GS69 Only)
(p. 15)
12
Zoom Lever [W/T] (pp. 37, 49)
13
Volume Lever [– / VOL +] (pp. 47, 50)
14
Microphone (built-in, stereo) (pp. 37, 41)
Audio-Video Output Jack [AV OUT]
15
(pp. 53, 56)
• Connecting an AV Cable to this jack activates
the Camcorder’s built-in speaker.
• When connecting the pin plug of the AV
Cable to this jack, plug it in as far as it goes.
16
18
24
Eyepiece Corrector Knob (p. 22)
Photoshot Button [PHOTO SHOT]
25
(pp. 33, 34)
26
Shoulder Strap Holders (p. 18)
27
Power Switch [OFF/ON] (p. 21)
28
Status Indicator [STATUS] (pp. 21, 36)
29
Menu Button [MENU] (p. 26)
30
Mode Dial (p. 23)
31
Recording Start/Stop Button (p. 31)
32
Joystick Control (pp. 23, 26)
Light Button [LIGHT] (p. 35)
33
34
21
35
Before Using
191720
Cassette Eject Lever [OPEN/EJECT]
16
22
(p. 18)
17
Cassette Holder (pp. 18~19)
18
Cassette Compartment Cover (pp. 18~19)
DV Input/Output Terminal
19
(pp. 56~57, 69~70)
• Connect this to the digital video equipment.
20
USB Jack [ ] (For PV-GS39/PV-GS69)
(pp. 60~61, 63, 69)
21
Speaker (p. 47)
22
Built-in LED Light (p. 35)
24
23
23
Viewfinder (pp. 21~23, 78)
Due to limitations in LCD production technology,
there may be some tiny bright or dark spots on the
Viewfinder screen.
However, this is not a malfunction and does not
affect the recorded picture.
25
27
28
32
29
30
31
26
36
34
Grip Belt (p. 17)
Tripod Receptacle
35
• This is a hole for attaching the Camcorder
to optional tripod. (Please carefully read the
Operating Instructions for how to attach the
tripod to the Camcorder.)
• You cannot open the Card Slot Cover when
the tripod is used. Insert the card first and
then attach the tripod.
Battery Eject Switch
36
[BATTERY RELEASE] (p. 16)
33
13
Remote Control
(PV-GS69 Only : Optional)
Using the Remote Control with the Camcorder, most
of the Camcorder functions can be operated from a
distance.
37
38
Indication Output Button [EXT DISPLAY]
37
(pp. 54, 56)
38
Date/Time Button [DATE/TIME] (p. 29)
Audio Dubbing Button [AUDIO DUB]
39
(p. 55)
40
Recording Button [● REC] (p. 57)
Cursor buttons for Variable Speed Search
41
Function [▲, ▼] (p. 48)
Select Button [▲▼◄►] (p. 27)
42
39
40
41
43
44
45
46
47
48
49
Photoshot Button [PHOTO SHOT]*
46
50
51
52
53
(pp. 33~34)
47
Rewind/Review Button [◄◄ ] (p. 48)
48
Pause Button [ ] (pp. 49, 55, 57)
49
Stop Button [■] (pp. 15, 57)
Recording Start/Stop Button
50
[START/STOP]* (p. 31)
51
Play Button [►] (pp. 48~49, 57)
52
Fast Forward/Cue Button [►► ] (p. 48)
53
Enter Button [ENTER] (p. 27)
* means that these buttons function in the same
manner as the corresponding buttons on the
Camcorder.
The Remote Control
(PV-GS69 Only : Optional)
Inserting the Button-type Battery
Before using the Remote Control, insert a
button-type battery (not supplied).
1 While pressing the Lock Button
the Battery Holder.
1
, pull out
14
Slow Motion/Still Advance Buttons [◄Ι, Ι►]
42
(◄Ι: reverse, Ι►: forward) (pp. 48~49)
Zoom/Volume Button [ZOOM/VOL]*
43
(pp. 37, 47)
Variable Speed Search Button
44
[VER SEARCH] (p. 48)
45
Menu Button [MENU]* (p. 27)
1
2 Insert a button-type battery (CR2025) with
the (+) marking facing upward.
3 Insert the Battery Holder into the Remote
Control.
• When the button-type battery is exhausted, replace
it with a new CR2025 battery. (A battery is normally
expected to last about 1 year. However, it depends
on operation frequency.)
• Make sure to match the poles correctly when
inserting the button-type battery.
WARNING
● Use Battery with Panasonic type CR2025
only. Use of another battery may present a
risk of fire or explosion.
● Battery may explode if mistreated.
● As with any small object, this type of
Battery can be swallowed by young
children. Do not allow children to handle
this Battery.
CAUTION
● Dispose of used battery promptly.
● Do not recharge, disassemble or dispose
of in fire.
Selecting Remote Control Modes
When 2 Camcorders are used simultaneously,
they can be operated individually by selecting
different Remote Control Modes.
• If the Remote Control Mode of the Camcorder
and that of the Remote Control do not match
with each other, [REMOTE] will appear. When
the Remote Control is operated for the first
time after the Camcorder is turned on, [CHECK
REMOTE MODE] (p. 74) will appear and
operation is impossible. Set the same Remote
Control Mode.
Setup on the Camcorder
Set [ REMOTE] on the [ SETUP] Sub-Menu to
the desired Remote Control Mode. (pp. 27~29)
Setup on the Remote Control
12
[VCR1]:
Press the [Ι►] Button and [ ■ ] Button
simultaneously.
[VCR2]:
Press the [◄Ι] Button and [ ■ ] Button
simultaneously.
• When the battery in the Remote Control is
replaced, the mode is automatically reset to [VCR1]
Mode.
1
2
Before Using
Using the Remote Control
(PV-GS69 Only : Optional)
1 Direct the Remote Control at the Remote
Control Sensor of the Camcorder and
press an appropriate button.
15°
15°
• Distance from the Camcorder: Within
approximately 15 feet (5 meters)
• Angle: Within approximately 15° in the vertical
and horizontal directions from the central axis
• The above operating ranges are for indoor use.
Outdoors or under strong light, the Camcorder may
not operate properly even within the above ranges.
15°
15°
Power Supply
Using the AC Adaptor
• Before connecting or disconnecting the
power supply, set the [OFF/ON] Switch on
the Camcorder to [OFF] and make sure that
[STATUS] Indicator is not lit. (p. 21)
15
1 Connect the DC Cable to the Camcorder.
2 Connect the DC Cable to the AC Adaptor.
3 Connect the AC Cable to the AC Adaptor
and the AC Jack.
1
2
3
Using the Battery
Before use, fully charge the Battery.
• We recommend using a Panasonic Battery.
• We cannot guarantee the quality of this Camcorder
when batteries from other companies are used.
1 Attach the Battery to the AC Adaptor and
charge it.
2 Put the Battery on the Battery Mount by
aligning the mark, and then securely plug
it in.
3 Attach the charged Battery to the
Camcorder.
Disconnecting the Power Source
Set the [OFF/ON] Switch to [OFF], and while
sliding the [BATTERY RELEASE] Switch, remove
the Battery downward or DC Cable.
• When attaching or removing Battery, set the
[OFF/ON] Switch to [OFF] and make sure the
[STATUS] Indicator is not lit.
• Hold down the battery with your hand so it
does not fall.
Notes:
• When the Camcorder has been used for a long
time, the Camera body becomes warm, but this is
not a malfunction.
• If the [CHARGE] Lamp does not light up although
the Battery is attached to the AC Adaptor, detach
the Battery and reattach it.
16
• Since the Battery will not be charged when
the DC Cable is connected to the AC Adaptor,
disconnect it from the AC Adaptor.
• The [CHARGE] Lamp lights up, and charging
starts.
• When the [CHARGE] Lamp goes off, charging
is completed.
• When the battery is completely discharged, the
[CHARGE] Lamp blinks at first, but the battery
is charged normally. When the temperature of
the battery is too high or low, the [CHARGE]
Lamp blinks and the charging time becomes
longer than usual.
Charging Time and Available
Recording Time
Supplied battery
(PV-GS29)
CGR-DU06
(7.2 V / 640 mAh)
Supplied battery
(PV-GS39)
CGR-DU06
(7.2 V / 640 mAh)
Supplied battery
(PV-GS69)
CGA-DU12
(7.2 V / 1 150 mAh)
A
B
C
A
B
C
A
B
C
1 h 40 min.
1 h 50 min. (1 h 25 min.)
55 min. (45 min.)
1 h 40 min.
1 h 45 min. (1 h 20 min.)
55 min. (40 min.)
2 h 25 min.
3 h 10 min. (2 h 30 min.)
1 h 35 min. (1 h 15 min.)
Optional battery
(PV-GS69)
CGR-DU06
(7.2 V / 640 mAh)
Optional battery
(PV-GS29)
CGA-DU12
(7.2 V / 1 150 mAh)
Optional battery
(PV-GS39)
CGA-DU12
(7.2 V / 1 150 mAh)
Optional battery
(PV-GS29)
CGA-DU21
(7.2 V / 2 040 mAh)
Optional battery
(PV-GS39/PV-GS69)
CGA-DU21
(7.2 V / 2 040 mAh)
A
Charging Time
B
Maximum Continuous Recording Time
C
Intermittent Recordable Time
(The intermittent recordable time refers to recordable
time when the recording and stopping operations are
repeated.)
• “1 h 40 min.” indicates 1 hour and 40 minutes.
• Battery CGR-DU06 (PV-GS29/PV-GS39) or
CGA-DU12 (PV-GS69) is supplied.
• The times shown in the table are approximate
times. The numbers indicate the recording time
when the Viewfinder is used. The numbers in
parentheses indicate the recording time when the
LCD Monitor is used. In actual use, the available
recording time may be shorter.
• The times shown in the table are for continuous
recording at a temperature of 25 °C (77 °F) and
humidity of 60 %. If the Battery is charged at a
higher or lower temperature, the charging time may
be longer.
• We recommend the Battery Pack CGA-DU12 and
CGA-DU21 for long time recording (2 hours or
more for continuous recording, 1 hour or more for
intermittent recording.)
• The available recording time becomes shorter
if you use both of Viewfinder and LCD Monitor
simultaneously when rotating the LCD Monitor
forward to record yourself.
• The batteries heat up after use or charging. The
Camcorder being used will also heat up. This is
normal.
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
1 h 40 min.
1 h 45 min. (1 h 20 min.)
55 min. (40 min.)
2 h 25 min.
3 h 15 min. (2 h 40 min.)
1 h 40 min. (1 h 20 min.)
2 h 25 min.
3 h 10 min. (2 h 30 min.)
1 h 35 min. (1 h 15 min.)
3 h 55 min.
5 h 45 min. (4 h 30 min.)
2 h 55 min. (2 h 15 min.)
3 h 55 min.
5 h 30 min. (4 h 15 min.)
2 h 45 min. (2 h 10 min.)
• Along with the reduction of the battery capacity,
the display will change:
→ . If the battery discharges, then
(
) will flash.
→ → →
To Use as a Grip Belt
Adjust the length of the Grip Belt to the size of your
hand.
1 Detach the end of the Grip Belt.
2 Adjust the length of the Grip Belt to the
size of your hand.
3 Reattach the Grip Belt.
Before Using
17
Re-attaching the Lens Cap
To protect the Lens surface, attach the Lens Cap.
• The Lens Cap and Lens Cap Cord come
preattached to the Grip Belt.
1 Pass one end of the Lens Cap Cord
through the attached eye on the Lens Cap.
Then pass the Lens Cap through the loop
made by itself and pull tight.
Attaching the Shoulder Strap
We recommend that you attach the Shoulder Strap
before going out to avoid dropping the Camcorder.
1 Pull the end of the Shoulder Strap
through the Shoulder Strap Holder on the
Camcorder.
2 Fold the end of the Shoulder Strap, run
it through the Shoulder Strap Length
Adjuster, and pull it.
• Pull it out more than 1 inch (2 cm) 1 from
the Shoulder Strap Length Adjuster so that it
cannot slip off.
• When not using the Lens Cap, pull the Lens Cap
Cord in the direction of the arrow.
• When you are not recording, be sure to cover the
Lens with the Lens Cap for protection.
1
• When you remove the Lens Cap, press the knobs
firmly.
1
2
1
• Attach the other end of the Shoulder Strap to
the other Shoulder Strap Holder in the same
way.
Inserting/Removing a Cassette
• Please use Genuine Panasonic DVC Tapes for
2
more information please contact your local dealer
or visit www.panasonic.com.
• For your reference if you travel frequently you
should also purchase a Panasonic head cleaning
tape AY-DVMCLA and use when HEAD CLOG
message appears on the LCD/EVF of your
Camcorder.
1 Fit the AC Adaptor or the Battery and turn
on the Power.
2 Slide the [OPEN/EJECT] Lever toward the
front and pull up to fully open the Cassette
Compartment Cover.
• To protect the tape, if the cover is not fully
opened, the cassette holder cannot be ejected.
18
3 After the Cassette Holder is opened,
insert/remove a Cassette.
• When inserting a cassette, orient it as shown in
the above, and then securely insert it as far as
it goes.
• When removing, pull it straight out.
4 Close the Cassette Holder by pressing the
[PUSH] mark 1.
• The Cassette Holder is housed.
1
Caution :
Before closing the Cassette Holder 2, be sure
your fingers have not been placed underneath the
Cassette Holder as shown below. This may cause
your fingers to jam in the cassette holder.
2
[Bottom View]Do not place fingers here.
5 Only after the Cassette Holder is
completely housed, close the Cassette
Compartment Cover by pressing the mark
3
.
3
When the Cassette Holder does not
come out
• Close the Cassette Compartment Cover
completely, and then open it again completely.
• Check if the battery has run down.
• Check if the Cassette Compartment Cover is in
contact with grip belt as shown below. If so, be
sure the grip belt stays clear of the cover when
opening.
When the Cassette Holder cannot be
housed
• Set the [OFF/ON] Switch to [OFF], then to [ON]
again.
• Check if the battery has run down.
Notes:
• After use, be sure to rewind the cassette
completely, remove it and put it in a case. Store the
case in an upright position. (p. 77)
• If the indicator of the condensation does not
display on the LCD screen and/or Viewfinder and
you notice condensation on the lens or the main
unit, do not open the cassette cover otherwise
condensation may be formed on the heads or the
cassette tape. (p. 76)
• When inserting a previously recorded Cassette,
use the Blank Search Function (p. 32) to find the
position where you want to continue recording.
If you overwrite-record on a previously recorded
cassette, be sure to find the position where you
want to continue recording.
• If a new Cassette is inserted, rewind to the
beginning of the tape before starting recording.
• When inserting the cassette, make sure it faces in
the right direction and then push it in until it stops.
• When the Cassette Holder is in action, do not touch
anything except the [PUSH] mark.
• Close the Cassette Compartment Cover tightly.
• When closing the Cassette Compartment Cover,
do not get anything, such as a cable, caught in the
cover.
Before Using
19
Accidental Erasure Prevention
Opening the accidental erasure prevention slider
1
on the cassette (by sliding it to the [SAVE] arrow
direction) prevents recording. To enable recording,
close the accidental erasure prevention slider (by
sliding it to the [REC] arrow direction).
1
Using a Memory Card (Optional)
(For PV-GS39/PV-GS69)
A Card can be used to record still pictures.
• Use a genuine SD Memory Card manufactured by
Panasonic only.
Before inserting or removing a Card, be sure to
turn off the Camcorder.
• Otherwise, the Camcorder may not function
properly or it may cause the loss of recorded data
in a Card.
Inserting/Removing a Card
1 Turn off the Power.
2 Open the LCD Monitor and then open the
Card Slot Cover.
Removing the Card
Open the Card Slot Cover and press the center of
the Card and then pull it straight out.
• After removing the Card, close the Card Slot
Cover.
• The Camcorder may be damaged if the Card is
forced out when the Card is fully inserted.
Concerning the Write Protection
Switch on the SD Memory Card
The SD Memory Card has a write protection
switch on it. If the switch is moved to [LOCK], you
cannot write to the card, erase the data on it, or
format it. If it is moved back, you can.
Concerning the Card
• Do not touch the terminals on the back of the
card.
• Do not format the card with another Camcorder
or any personal computer. This operation may
make the card unusable.
• Electrical noise, static electricity, or failure of the
Camcorder or the card may damage or erase
the data stored on the card. We recommend
saving important data on a personal computer by
using a USB Cable, PC Card Adaptor, and USB
Reader/Writer.
SD Memory Card
• The memory capacity indicated on the SD
Memory Card label corresponds to the total
amount of capacity to protect and manage
the copyright and the capacity available as
conventional memory for a Camcorder, personal
computer or other equipment.
Card Access Lamp
3 While holding the Memory Card with its
cut corner facing right 1, insert/remove it
into/from the Card Slot.
4 Close the Card Slot Cover securely.
20
While the Camcorder is accessing the Card (reading,
recording, playback or erasing), the Card Access
Lamp lights up.
• While the Card Access Lamp is on, never attempt
to open the Card Slot Cover, to pull out the Card,
to turn off the Camcorder, or to turn the Mode Dial.
1
Such actions will damage the Card, and recorded
data, and cause the Camcorder to malfunction.
Turning on the Camcorder
Turn on the power first and then select modes.
How to Turn on the Power
1 Set the [OFF/ON] Switch to [ON] while
pressing the button 1.
1
2 Open the LCD Monitor or extend the
Viewfi nder to use.
• The [STATUS] Indicator lights Red and turn on
the power.
• The LCD Monitor or Viewfinder will be
activated.
How to Turn off the Power
1 Set the [OFF/ON] Switch to [OFF] while
pressing the button 1.
• The [STATUS] Indicator goes off when the
power turns off.
• In Tape Recording Mode or Card Recording
Mode, if the [OFF/ON] Switch is set to [ON]
while the LCD Monitor and Viewfinder are
closed, the power turns off.
1
2 Close the LCD Monitor and retract the
Viewfi nder.
• The power will not turn off if the LCD Monitor is
closed and the Viewfinder is retracted.
• The [STATUS] Indicator
off and the power turns off. (If Quick Start
is set to [ON] (pp. 35~36, the unit goes into
Quick Start standby mode and the [STATUS]
Indicator lights Green.)
• Even if the LCD Monitor is closed or the
Viewfinder is retracted while recording on
a tape, the power does not turn off. (The
Viewfinder stays lit up.)
2
automatically goes
3 Open the LCD Monitor or extend the
Viewfi nder again.
• The [STATUS] Indicator lights Red and turn on
the power.
Setting Date and Time
When the Camcorder is turned on for the first time,
[SET DATE AND TIME] will appear. Select [YES]
and set the date and time.
• If the screen shows the incorrect Date/Time, then
adjust it.
Before Using
2
How to turn the power on and off with
the LCD Monitor/Viewfinder
When the [OFF/ON] Switch is set to [ON], the power
can be turned on and off with the LCD Monitor and
the Viewfinder when the unit is in Tape Recording
Mode or Card Recording Mode.
1 Open the LCD Monitor or extend the
Viewfi nder to use.
• The LCD Monitor or the Viewfinder will be
activated.
SET DATE AND TIME
YES
SETUP ENTER EXIT
• Set to Tape/Card Recording Mode.
(PV-GS39/
PV-GS69)
NO
(PV-GS29)
21
1 Set [ BASIC] >> [ CLOCK SET] >>
[YES].
CLOCK SET
JAN .01.2006 12:00AM
SETUP
SET ENTER EXIT
2 Move the Joystick Control [◄] or [►] to
select the item to be set. Then move the
Joystick Control [▲] or [▼] to set the
desired value.
• Year will cycle in the order shown below.
2000, 2001, ..., 2089, 2000, ...
3 Press the Joystick Control to fi nish setting
the date and time.
• The clock operation starts from [00] second.
• If the built-in battery is weak, the [ ] Indication
flashes. In this case, charge the built-in battery.
• The clock uses the 12-hour system.
About Date/Time
• The Date and Time function are driven by a
built-in lithium battery.
• Make sure to check the time before recording
because the built-in clock is not very accurate.
Recharging the built-in lithium battery
If [ ] or [--] is appears when the Camcorder is
turned on, then the built-in lithium battery has run
down. Use the steps below to charge the battery.
When the battery is inserted for the first time after
charging, [SET DATE AND TIME] will appear.
Select [YES] and set the date and time.
Connect the AC adaptor to the Camcorder or
place the battery on the Camcorder, and the
built-in lithium battery will be recharged. Leave the
camera as is for approx. 24 hours, and the battery
will drive the date and time for approx. 6 months.
(Even if the [OFF/ON] Switch is set to [OFF], the
battery is still being recharged.)
Using the Viewfinder/ LCD Monitor
Using the Viewfinder
Before using the Viewfinder, adjust the field of view
so that the displays inside the Viewfinder become
clear and easy to read.
1 Pull the Viewfi nder.
• The Viewfinder will be activated.
2 Adjust by turning the Eyepiece Corrector
Knob.
• You can adjust the brightness of the Viewfinder
from the Menu.
Using the LCD Monitor
With the LCD Monitor open, you can also record the
picture while watching it.
1 Place your Thumb on the [OPEN] Knob
and pull the LCD Monitor out in the
direction of the arrow.
• The LCD Monitor will be activated.
• It can open up to 90°.
22
2 Adjust the LCD Monitor angle according to
the desired recording angle.
• The LCD Monitor can rotate a maximum of
180°
from the vertical position upwards
1
and a maximum of 90°
direction. Forcefully rotating the LCD Monitor
beyond these ranges will damage the
Camcorder.
1
180°
2
to the downward
90°
2
• The brightness and color level of the LCD Monitor
can be adjusted from the Menu.
• If it is forcibly opened or rotated, the Camcorder
may be damaged or fail.
• Check that the Card Slot Cover is closed before
closing the LCD Monitor.
• If the LCD Monitor is rotated by 180° towards the
lens and the Viewfinder is opened (when recording
yourself), the LCD Monitor and the Viewfinder
simultaneously light.
Closing the LCD Monitor
Push the LCD Monitor until it is securely locked.
• Make sure the Card Slot Cover is closed.
Adjusting Brightness and Color Level
When [
SETUP] Sub-Menu is set to [YES], the following
items are displayed.
[ LCD SET] LCD Brightness [ ]
Adjusts the brightness of the image on the LCD
screen.
[ LCD SET] LCD Color Level [ ]
Adjusts the color saturation of the image on the LCD
screen and the Viewfinder.
[ EVF SET] Brightness of the Viewfinder
[
Adjusts the brightness of the image in the Viewfinder.
LCD SET] or [ EVF SET] on the [
LCD SET
SET
SETUP ENTER EXIT
SET ENTER EXIT
]
EVF SET
To Adjust
Move the Joystick Control [▲] or [▼] and select
the item to be adjusted, and then move the
Joystick Control [◄] or [►] to raise or lower the
number of vertical bars in the Bar Indication.
• More vertical bars indicates stronger brightness
or color saturation.
• Press the [MENU] Button or the Joystick Control
to complete the settings.
Notes:
• In order to adjust the brightness of the Viewfinder,
close the LCD Monitor, and the Viewfinder will be
activated.
• When the LCD Monitor is rotated by 180° towards
the lens, the brightness of the LCD Monitor cannot
be adjusted.
• These settings will not affect the images actually
recorded.
Easy to Use Mode Dial
You can choose a desired mode by rotating the
Mode Dial.
1 Rotate the Mode Dial.
• Set your desired mode to 1.
1 1
(PV-GS39/
PV-GS69)
Tape Recording Mode
:
Use this mode when recording pictures on a
tape.
Tape Playback Mode
:
Use this mode when playing back the
recorded scene on a tape.
Card Recording Mode
:
(For PV-GS39/PV-GS69)
Use this mode when recording still pictures
on a card.
Picture Playback Mode
:
(For PV-GS39/PV-GS69)
Use this mode when playing back the
recorded still picture on a card.
PC Mode (For PV-GS39/PV-GS69)
:
Use this mode when you want to connect the
Camcorder to your Personal Computer.
You can view or edit the images recorded on a
card on your personal computer.
How to Use the Joystick Control
Basic Joystick Control Operations
Operations on the menu screen and selection
of files to be played back on the multi-image
display.
Move the Joystick Control [▲,▼,◄, or ►] to select
an item or file, and then press in the center to set it.
1
4
3
5
(PV-GS29)
Joystick Control (See below)
2
One-Touch
Navigation icon
Select by moving [▲].
1
Select by moving [►].
2
Select by moving [▼].
3
Select by moving [◄].
4
Push the center to select
5
the item.
Before Using
23
Joystick Control and Screen Display
Press the center of the Joystick Control, and the
One-Touch Navigation icon will be displayed on the
lower right of the screen.
• Press the Joystick Control again to turn off the
One-Touch Navigation icon.
• Pressing the center button of the Joystick Control
again to redisplay the One-Touch Navigation icon
will display the last page used.
Each press of [▼] switches the display as follows
depending on the mode.
Press Center
Press ▼
1/4 NEXT
2/4 NEXT
3/4 NEXT
4/4 NEXT
Move the Joystick Control [▲, ▼, ◄, or ►] to select
an item.
• In the Tape Playback Mode or the Picture Playback
Mode, the One-Touch Navigation icon will be
automatically on the lower right of the screen.
e.g., Tape Recording Mode
[AUTO]
One-Touch
Navigation icon OFF
Tape Recording Mode
• When the [AUTO/MANUAL/FOCUS] Switch is
set to [AUTO].
2/4 NEXT
1
3/4 NEXT
4/4 NEXT
Fade pp. 38~39
Help Mode* p. 26
Backlight compensation p. 39
1/4
1/4 NEXT
◄
►
▲
▼ Go to next page. –
Soft Skin Mode p. 40
◄
2/4
▼ Go to next page. –
▲ MagicPix Mode p. 40
3/4
▼ Go to next page. –
◄
Recording Check p. 32
4/4
Blank Search Mode p. 32
►
▼ Go to next page. –
• 1 is displayed while recording on a tape.
Tape Recording Mode
• When the [AUTO/MANUAL/FOCUS] Switch is
set to [MANUAL].
1/5 NEXT
2/5 NEXT
3/5 NEXT
24
WB
IRIS
SHTR
5/5
1/2 NEXT
Manual Iris Adjustment
◄
Mode
Manual Shutter Speed
►
Adjustment Mode
Manual White Balance
▲
Adjustment Mode
5/5 NEXT
WB
IRIS
2/2 NEXT
SHTR
4/5 NEXT
1
▼ Go to next page. –
• 1 is displayed while recording on a tape.
pp. 45~46
p. 45
pp. 43~44
Tape Recording Mode
• When the [AUTO/MANUAL/FOCUS] Switch is
set to [FOCUS].
1/6 NEXT
MF–MF
6/6 NEXT
1/3 NEXT
2/6 NEXT
WB
IRIS
+
SHTR
5/6 NEXT
WB
IRIS
2/3 NEXT
SHTR
3/6 NEXT
4/6 NEXT
MF–MF
3/3 NEXT
+
Card Recording Mode
(For PV-GS39/PV-GS69)
• When the [AUTO/MANUAL/FOCUS] Switch is
set to [FOCUS].
WB
1/4 NEXT
◄
4/4
1
►
▼ Go to next page. –
2/4 NEXT
Manual Focus Adjustment
Mode
Manual Focus Adjustment
Mode
IRIS
3/4 NEXT
SHTR
MF–MF
4/4 NEXT
p. 46
p. 46
Before Using
+
6/6
Manual Focus Adjustment
◄
Mode
Manual Focus Adjustment
►
Mode
p. 46
p. 46
▼ Go to next page. –
• 1 is displayed while recording on a tape.
Card Recording Mode
(For PV-GS39/PV-GS69)
• When the [AUTO/MANUAL/FOCUS] Switch is
set to [AUTO].
2/2 NEXT
Self-timer Mode p. 36
Help Mode* p. 26
Backlight compensation p. 39
1/2
1/2 NEXT
◄
►
▲
▼ Go to next page. –
◄ Soft Skin Mode p. 40
2/2
▼ Go to next page. –
Card Recording Mode
(For PV-GS39/PV-GS69)
• When the [AUTO/MANUAL/FOCUS] Switch is
set to [MANUAL].
1/3 NEXT 2/3 NEXT 3/3 NEXT
IRIS
WB
SHTR
Tape Playback Mode
Playback / Pause p. 47
▲
Fast (Cue Playback) p. 48
►
–
Rewind (Review Playback) p. 48
◄
▼
Stop p. 47
Picture Playback Mode
(For PV-GS39/PV-GS69)
Start the Slide Show
▲
Stop the Slide Show
►
–
Playback the next picture p. 49
Playback the previous
◄
picture
▼
Erase the picture p. 51
pp. 49~51
p. 49
Manual Iris Adjustment
◄
Mode
Manual Shutter Speed
►
3/3
Adjustment Mode
Manual White Balance
▲
Adjustment Mode
▼ Go to next page. –
pp. 45~46
p. 45
pp. 43~44
25
*Help Mode
• Set to Tape/Card Recording Mode.
You can view function help information using
One-Touch Navigation.
1 Press the Joystick Control to display the
One-Touch Navigation icon on the lower
right of the screen.
2 Move the Joystick Control [▼] until the
page with [ ] indication is displayed.
[One-Touch Navigation icon]
e.g.
1/4 NEXT
3 Move the Joystick Control [►] to select
[ ].
e.g.
USAGE
TO MOVE JOYSTICK
IN DIRECTION
OF DESIRED
FUNCTION
SET EXIT
1/4 NEXT
EXIT
4 Move the Joystick Control [▲▼◄►] to
select the desired function.
e.g.
BACKLIGHT COMPENSATION
PREVENTS
DARK
SUBJECTS
IN BACKLIGHT
SET EXIT
• An explanation of the selected icon is displayed
on the screen.
• Each time the Joystick Control is moved down,
the indication changes.
To end the Help Mode
Move the Joystick Control [►] to select [EXIT] or
press the [MENU] Button.
Notes:
• When the Help Mode is used, functions cannot be
set.
• The Help Mode only displays the information
available in [AUTO] Mode.
1/4 NEXT
EXIT
Using the Menu Screen
To facilitate the selection of a desired function or
setup, this Camcorder displays various function
setups on Menus.
1 Press the [MENU] Button.
• The Menu corresponding to the Mode selected
by the Mode Dial is displayed.
• Do not switch the Mode Dial when the Menu is
displayed.
(PV-GS39/
PV-GS69)
(PV-GS29)
2 Move the Joystick Control [▲] or [▼] to
select the top menu.
BASIC
ADVANCED
SETUP
LANGUAGE
SETUP ENTER EXIT
3 Move the Joystick Control [►] or press it
to set the selection.
4 Move the Joystick Control [▲] or [▼] to
select the Sub-Menu.
BASIC
SCENE MODE
REC SPEED
WIND CUT
ASPECT
CLOCK SET
SETUP ENTER EXIT
OFF
SP
ON
16:9
NO
5 Move the Joystick Control [►] or press it
to set the selection.
6 Move the Joystick Control [▲] or [▼] to
select the item to be set.
BASIC
SCENE MODE
REC SPEED
WIND CUT
ASPECT
CLOCK SET
SETUP ENTER EXIT
OFF
7 Press the Joystick Control to determine
the setting.
• While a Menu is displayed, you cannot record or
play back. Menus can be displayed during playback
but not during recording.
26
To Return to the Previous Screen
Move the Joystick Control [◄].
To Exit the Menu Screen
Press the [MENU] Button again.
About the Menu Mode Setting
The setting selected on the Menu will be retained
even when the Camcorder is turned off. However,
if the Battery or AC Adaptor is disconnected before
turning off the Camcorder, the selected setup may
not be retained.
• Menu operation flow is shown in this text by >>.
Operating with Remote Control
(PV-GS69 Only : Optional)
The menu screen transition is the same as when the
buttons on the main unit are used.
1 Press the [MENU] Button.
2 Select a menu item.
• Use the Select Button (▲▼◄►) and [ENTER]
Button in place of the Joystick Control on the
main unit.
3 Press the [MENU] Button to exit the menu
screen.
Selecting Language
You can select the desired language.
1 Set [ LANGUAGE] >> [English],
[Français] or [Español].
LANGUAGE
English
Español
SETUP ENTER EXIT
Français
List of Menus
The figures of the Menus are for explanation
purposes only, and they are different from the actual
Menus.
[TAPE RECORDING MENU]
e.g.,
BASIC
ADVANCED
SETUP
LANGUAGE
SETUP ENTER EXIT
[ BASIC]
Basic Setup Sub-Menu
[ SCENE MODE]
Scene Mode (pp. 42~43)
[ REC SPEED]
Recording Speed Mode (p. 30)
[ WIND CUT]
Wind Noise Reduction (p. 41)
[ ASPECT] (For PV-GS39/PV-GS69)
Wide Screen Mode (p. 41)
[ CINEMA] (PV-GS29 Only)
Cinema-like Format Recording (p. 41)
[ CLOCK SET]
Date and Time Setting (pp. 21~22)
[ ADVANCED]
Advance Setup Sub-Menu
[ PICT.QUALITY] (For PV-GS39/PV-GS69)
Picture Quality (p. 33)
[ EIS]
Image Stabilizer (p. 38)
[ FADE COLOR]
Fade color (pp. 38~39)
[ AUDIO REC]
Audio Recording Mode (p. 29)
[ USB FUNCTION] (PV-GS69 Only)
USB Functions Mode (pp. 63, 69)
[ D.ZOOM]
Digital Zoom (p. 37)
[ ZOOM MIC]
Zoom Microphone (p. 37)
[ SHTR EFFECT] (PV-GS29 Only)
Shutter effect (p. 33)
[ SETUP]
Setup Sub-Menu
[ DISPLAY]
Display Mode (p. 29)
[ DATE/TIME]
Date and Time Indication (pp. 29, 73)
[ POWER SAVE]
Power Save Mode (p. 30)
[ QUICK START]
Quick Start Mode (pp. 35~36)
[ REMOTE] (PV-GS69 Only)
Remote Control Mode (p. 15)
[ BEEP SOUND]
Beep Sound (p. 29)
BASIC
SCENE MODE
REC SPEED
WIND CUT
ASPECT
CLOCK SET
SETUP ENTER EXIT
OFF
SP
ON
16:9
NO
Before Using
27
LCD SET]
[
LCD Adjustment (p. 23)
[ EVF SET]
Viewfinder Adjustment (p. 23)
[ INITIAL SET]
Initial Setting Mode (p. 30)
[ DEMO MODE]
Demonstration Mode (p. 30)
[ LANGUAGE]
Language Setup Sub-menu (p. 27)
[TAPE PLAYBACK MENU]
e.g.,
SETUP ENTER EXIT
BASIC
ADVANCED
SETUP
LANGUAGE
BASIC
DATE/TIME
USB FUNCTION
SETUP ENTER EXIT
MOTION DV
[ BASIC]
Basic Setup Sub-Menu
[ DATE/TIME]
Date and Time Indication (pp. 29, 73)
[ USB FUNCTION] (PV-GS69 Only)
USB Functions Mode (pp. 63, 69)
[ ADVANCED]
Advance Setup Sub-Menu
[ REC SPEED]
Recording Speed Mode (p. 30)
[ REC STDBY]
Recording Standby Mode (p. 57)
[ PICT.QUALITY] (For PV-GS39/PV-GS69)
Picture Quality (p. 33)
[ REPEAT PLAY]
Repeat Play Mode (p. 47)
[ SETUP]
Setup Sub-Menu
[ 12bit AUDIO]
Audio Selector (p. 47)
[ AUDIO OUT]
Audio Output Mode (p. 30)
[ DISPLAY]
Display Mode (p. 29)
[ REMOTE] (PV-GS69 Only)
Remote Control Mode (p. 15)
[ LCD SET]
LCD Adjustment (p. 23)
[ EVF SET]
Viewfinder Adjustment (p. 23)
[ POWER SAVE]
Power Save Mode (p. 30)
[ TV ASPECT] (For PV-GS39/PV-GS69)
TV Aspect Mode (p. 53)
[ LANGUAGE]
Language Setup Sub-menu (p. 27)
D/T
[CARD RECORDING MENU]
(For PV-GS39/PV-GS69)
e.g.,
BASIC
ADVANCED
SETUP
LANGUAGE
SETUP ENTER EXIT
SCENE MODE
PICT.QUALITY
ASPECT
CLOCK SET
SETUP ENTER EXIT
[ BASIC]
Basic Setup Sub-Menu
[ SCENE MODE]
Scene Mode (pp. 42~43)
[ PICT.QUALITY]
Picture Quality (p. 33)
[ ASPECT]
Wide Screen Mode (p. 41)
[ CLOCK SET]
Date and Time Setting (pp. 21~22)
[ ADVANCED]
Advance Setup Sub-Menu
[ BURST MODE]
RapidFire Consecutive Photoshot (p. 34)
[ SHTR EFFECT]
Shutter Effect (p. 33)
[ SETUP]
Setup Sub-Menu
[ DISPLAY]
Display Mode (p. 29)
[ DATE/TIME]
Date and Time Indication (pp. 29, 73)
[ POWER SAVE]
Power Save Mode (p. 30)
[ QUICK START]
Quick Start Mode (pp. 35~36)
[ REMOTE] (PV-GS69 Only)
Remote Control Mode (p. 15)
[ BEEP SOUND]
Beep Sound (p. 29)
[ LCD SET]
LCD Adjustment (p. 23)
[ EVF SET]
Viewfinder Adjustment (p. 23)
[ INITIAL SET]
Initial Setting Mode (p. 30)
[ LANGUAGE]
Language Setup Sub-menu (p. 27)
BASIC
OFF
16:9
NO
28
[PICTURE PLAYBACK MENU]
(For PV-GS39/PV-GS69)
e.g.,
SETUP ENTER EXIT
BASIC
ADVANCED
SETUP
LANGUAGE
BASIC
DATE/TIME
PROTECT
SETUP ENTER EXIT
[ BASIC]
Basic Setup Sub-Menu
[ DATE/TIME]
Date and Time Indication (pp. 29, 73)
[ PROTECT]
Setting the Lock (pp. 52~53)
[ ADVANCED]
Advance Setup Sub-Menu
[ DPOF SET]
Setting DPOF (p. 52)
[ FORMAT CARD]
Formatting a Card (p. 53)
[ SETUP]
Setup Sub-Menu
[ DISPLAY]
Display Mode (p. 29)
[ REMOTE] (PV-GS69 Only)
Remote Control Mode (p. 15)
[ LCD SET]
LCD Adjustment (p. 23)
[ EVF SET]
Viewfinder Adjustment (p. 23)
[ POWER SAVE]
Power Save Mode (p. 30)
[ TV ASPECT]
TV Aspect Mode (p. 53)
[ LANGUAGE]
Language Setup Sub-menu (p. 27)
D/T
Menus Related to Taking Pictures
DATE/TIME
NO
This switches between date and time indications.
Set [
BASIC] or [ SETUP] >> [ DATE/TIME]
>> [D/T], [DATE] or [OFF].
• The Camcorder automatically records the date
and time of picture taking on the tape.
• You can also show or change the Date/Time
Indication by repeatedly pressing the [DATE/
TIME] Button on the Remote Control (PV-GS69
Only).
Before Using
DISPLAY
Set [ SETUP] >> [ DISPLAY] >> [ON] or
[OFF].
Set to [ON] and the display mode can be switched
to all functions. Set to [OFF] and it can be
switched to minimum display.
AUDIO REC
• Set to Tape Recording Mode.
You can select the sound quality of the recorded
sound.
Set [
ADVANCED] >> [ AUDIO REC] >>
[12bit] or [16bit].
[12bit]: Records audio in “12 bit 32 kHz
[16bit]: Records audio in “16 bit 48 kHz
4 tracks”. (The original audio signals can
be kept after the other audio signals are
dubbed.)
2 tracks”. Audio can be recorded in
higher quality. (If audio signals are
dubbed, then the original audio signals
will be erased.)
BEEP SOUND
• Set to Tape/Card Recording Mode.
When [
set to [ON], confirmation/alarm beeps are issued
as follows.
1 Beep
• When you start recording
• When you turn on the power
• When the unit goes from Quick Start standby
2 Beeps
• When you pause recording
• When you turn off the power
• When the unit goes into Quick Start standby
2 Beeps 4 times
• When a cassette with its erasure prevention tab
BEEP SOUND] on the [ SETUP] is
mode to recording pause
mode
set to [SAVE] is inserted, condensation occurs
(p. 76), and at other times. Check the sentence
displayed on the screen (pp. 74~75).
29
POWER SAVE
Set [ SETUP] >> [ POWER SAVE] >>
[5 MINUTES] or [OFF].
[OFF]:
When about 5 minutes passed without any
operation, the standby mode automatically will be
set. In the standby mode, [
time more than usual to start recording after you
press the Recording Start/Stop Button.
[5 MINUTES]:
When about 5 minutes passed without any
operation, the Camcorder automatically turns off
to protect the tape or to prevent the battery from
running down. When you use the Camcorder, turn
it on again.
• In the following cases, the power may not
turn off even when set [
[5 MINUTES].
- When connecting to the AC Jack
(When using the AC Adaptor)
- When connecting the USB Cable or the DV
Cable to a PC or other equipment
- When the PC Mode (For PV-GS39/PV-GS69)
] blinks and it takes
POWER SAVE] >>
Menus Related to Playback
AUDIO OUT
This switches the sound to be played back.
Set [
SETUP] >> [ AUDIO OUT] >>
[STEREO], [L] or [R].
[STEREO]: Stereo sound (main sound and sub
[L]: Left channel sound (main sound)
[R]: Right channel sound (sub sound)
sound)
Other Menus
INITIAL SET
• Set to Tape/Card Recording Mode.
Set [
SETUP] >> [ INITIAL SET] >> [YES] or
[NO].
Set to [YES] to change menu settings back to their
factory default condition.
• The initializing takes a little while.
• Language setting cannot be back to the initial
shipping condition.
DEMO MODE
• Set to Tape Recording Mode.
If you set [
>> [ON] without inserting a cassette or a
card, the Camcorder is automatically set to
the demonstration mode for introducing its
functions. If any button is pressed or operated,
the demonstration mode is canceled. If no
operations take place for approx. 10 minutes,
the demonstration mode automatically starts.
To terminate the demonstration mode, insert a
cassette or a card, or set to [
[OFF]. For normal use, set this function to [OFF].
SETUP] >> [ DEMO MODE]
DEMO MODE] >>
LP Mode
You can switch the tape recording speed.
• Set to Tape Recording/Playback Mode.
1 Set [ BASIC] or [ ADVANCED] >> [
REC SPEED] >> [LP].
If the LP mode is selected, the recording
time will be 1.5 times the SP mode, but some
functions will be disabled.
• We recommend using the SP mode for important
recordings.
• In order to fully exhibit the performances of the LP
mode, we recommend using Panasonic cassettes
marked LP mode.
• Audio dubbing is not possible with LP Mode. (p. 55)
• In the LP mode, the picture quality will not be
degraded in comparison with the SP mode, but
mosaic noise may appear on the playback image or
some functions may be disabled.
- Playback on other digital video equipment or on
digital video equipment without the LP mode.
- Playback of the image on other digital video
equipment recorded in the LP mode.
- Slow Motion/Still Advance playback.
30
Loading...