Panasonic PT-AE3000 User Manual
Operating Instructions
LCD Projector
Model No. PT-AE3000E
Before operating this product, please read the instructions carefully and save this manual for future use.
TQBJ0278-1
ENGLISH
Information
Important Safety Notice
Important
Dear Panasonic Customer:
This instruction booklet provides all the necessary operating information that you might require. We hope it will help
you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. The
serial number of your product may be found on its bottom. You should note it in the space provided below and retain
this booklet in case service is required.
WARNING: THIS APPARATUS MUST BE EARTHED.
WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance
Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator
position is equal or less than 70 dB (A) according to ISO 7779.
WARNING:
1. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time.
2. To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified
service personnel.
3. Do not remove the earthing pin on the mains plug. This apparatus is equipped with a three prong earthingtype mains plug. This plug will only fit an earthing-type mains socket. This is a safety feature. If you are unable
to insert the plug into the mains socket, contact an electrician. Do not defeat the purpose of the earthing plug.
Model number: PT-AE3000E
Serial number:
to rain or moisture.
Information for Users on Collection and Disposal of Old Equipment and used
Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical
and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC
and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and
prevent any potential negative effects on human health and the environment which could otherwise
arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your
local municipality, your waste disposal service or the point of sale where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
Information on Disposal in other Countries outside the European Union
These symbols are only valid in the European Union. If you wish to discard these items, please contact
your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
CAUTION: To assure continued compliance, follow the attached installation instructions, which includes using
the provided power cord and shielded interface cables when connecting to computer or peripheral
device. If you use serial port to connect PC for external control of projector, you must use optional
RS-232C serial interface cable with ferrite core. Any unauthorized changes or modifications to this
equipment will void the user’s authority to operate.
2 - ENGLISH
Important Safety Notice
Pursuant to at the directive 2004/108/EC, article 9(2)
Panasonic Testing Centre
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany
IMPORTANT: THE MOULDED PLUG (U.K. only)
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is
fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating
of13 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark a or the BSI mark ` on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose
the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be
purchased from an Authorised Service Centre.
If the fitted moulded plug is unsuitable for the mains socket in your home, then the fuse should be removed
and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is
inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
Important
Information
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green - and - Yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows.
The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the plug
which is marked with the letter E or by the Earth symbol W or coloured GREEN or GREEN - AND YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with
the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with
the letter L or coloured RED.
How to replace the fuse
: Open the fuse compartment with a screwdriver and replace the fuse.
13A250V
BS1363/A
L
ASA
N
HE-8
ENGLISH - 3
Contents
J Quick steps
1. Set up your projector
See “Setting up” on page 14.
2. Connect with other devices
See “Connections” on page 18.
3. Prepare the remote control
See “Remote control” on page 11.
Important Information
Important Safety Notice........................................ 2
Precautions with regard to safety ....................... 6
WARNINGS.................................................................6
CAUTIONS..................................................................7
Cautions when transporting.........................................8
Cautions when installing..............................................9
Cautions on use ..........................................................9
Accessories ...............................................................10
Preparation
About Your Projector.......................................... 11
Remote control ..........................................................11
Projector body ...........................................................12
Getting Started
Setting up............................................................. 14
Screen size and throw distance.................................14
Projection method......................................................15
Front leg adjusters and throwing angle .....................15
Lens shift and positioning..........................................16
Connections ........................................................ 18
Before connecting to the projector.............................18
Connecting example: COMPONENT IN/S-VIDEO IN/
VIDEO IN...................................................................18
Connecting example: HDMI IN/COMPUTER IN........ 18
4. Start projecting
See “Switching the projector on/off” on
page 19.
5. Adjust the image
See “Menu Navigation” on page 29.
Basic Operation
Switching the projector on/off ........................... 19
Mains lead .................................................................19
Power indicator..........................................................20
Switching on the projector .........................................21
Switching off the projector .........................................21
Projecting an image ............................................ 22
Selecting the input signal...........................................22
Positioning the image ................................................22
Remote control operation .................................. 23
Operating range ........................................................23
Managing the lens control settings ............................23
Switching the picture mode .......................................23
Adjusting the image...................................................23
Loading a saved setting ............................................24
Switching the aspect ratio..........................................24
Adjusting the signal condition with a waveform .........24
Setting your own colour profile ..................................26
Resetting to the factory default settings ....................28
Capturing an image ...................................................28
Switching the input signal..........................................28
Using the assigned function as shortcut....................28
4 - ENGLISH
Contents
Settings
Menu Navigation ..................................................29
Navigating through the MENU .................................. 29
Main menu and sub-menu ........................................ 30
PICTURE menu.....................................................32
PICTURE MODE....................................................... 32
CONTRAST .............................................................. 32
BRIGHTNESS........................................................... 32
COLOUR...................................................................32
TINT .......................................................................... 32
SHARPNESS ............................................................32
COLOUR TEMPERATURE....................................... 33
DYNAMIC IRIS.......................................................... 33
WAVEFORM MONITOR ........................................... 33
SPLIT ADJUST ......................................................... 33
ADVANCED MENU...................................................34
MEMORY SAVE ....................................................... 36
MEMORY LOAD ....................................................... 36
MEMORY EDIT......................................................... 36
SIGNAL MODE ......................................................... 36
POSITION menu ...................................................37
H-POSITION ............................................................. 37
V-POSITION ............................................................. 37
DOT CLOCK ............................................................. 37
CLOCK PHASE.........................................................37
ASPECT....................................................................37
WSS .......................................................................... 39
OVER SCAN .............................................................39
KEYSTONE............................................................... 39
AUTO SETUP ........................................................... 39
LENS CONTROL...................................................40
ZOOM/FOCUS..........................................................40
LENS MEMORY LOAD............................................. 40
LENS MEMORY SAVE ............................................. 40
LENS MEMORY EDIT .............................................. 41
H-AREA POSITION .................................................. 41
V-AREA POSITION................................................... 41
FUNCTION BUTTON.............................................42
BUTTON ................................................................... 42
OPTION menu.......................................................43
INPUT GUIDE ........................................................... 43
OSD DESIGN............................................................ 43
OSD POSITION ........................................................ 43
BACK COLOUR ........................................................43
STARTUP LOGO ......................................................43
AUTO SEARCH ........................................................ 43
HDMI SIGNAL LEVEL............................................... 43
FRAME RESPONSE.................................................43
INSTALLATION......................................................... 44
SLEEP....................................................................... 44
HIGH ALTITUDE MODE ........................................... 44
LAMP POWER.......................................................... 44
LAMP RUNTIME .......................................................44
Maintenance
TEMP and LAMP Indicators ............................... 45
Managing the indicated problems............................. 45
Care and Replacement ....................................... 46
Cleaning the projector............................................... 46
Replacing the lamp unit ............................................ 47
Troubleshooting.................................................. 49
Appendix
Technical Information......................................... 50
List of compatible signals.......................................... 50
Serial terminal........................................................... 51
Specifications............................................................ 54
Ceiling mount bracket safeguards ............................ 56
Dimensions ............................................................... 57
Trademark acknowledgements................................. 57
Index..................................................................... 58
Important
Information
PreparationGetting StartedBasic OperationSettingsMaintenanceAppendix
ENGLISH - 5
Information
Precautions with regard to safety
Important
WARNINGS
If you notice smoke, strange smells or noise coming
from the projector, disconnect the mains plug from
the mains socket.
Do not continue to use the projector in such cases,
otherwise fire or electric shocks could result.
Check that no more smoke is coming out, and then
contact an Authorised Service Centre for repairs.
Do not attempt to repair the projector yourself, as this
can be dangerous.
Do not install this projector in a place which is not
strong enough to take the full weight of the
projector.
If the installation location is not strong enough, it may
fall down or tip over, and severe injury or damage
could result.
Installation work (such as ceiling suspension)
should only be carried out by a qualified technician.
If installation is not carried out correctly, there is the
danger that injury or electric shocks may occur.
Do not use other than an authorised ceiling mount
bracket.
If foreign objects or water get inside the projector, or
if the projector is dropped or the cabinet is broken,
disconnect the mains plug from the mains socket.
Continued use of the projector in this condition may
result in fire or electric shocks.
Contact an Authorised Service Centre for repairs.
The mains socket shall be installed near the
equipment and shall be easily accessible.
Unplug the mains plug from the mains socket
immediately when problem occurred.
Do not overload the mains socket.
If the power supply is overloaded (for example, by
using too many adapters), overheating may occur
and fire may result.
Never attempt to modify or disassemble the
projector.
High voltages can cause fire or electric shocks.
For any inspection, adjustment and repair work,
please contact an Authorised Service Centre.
Clean the mains plug regularly to prevent it from
becoming covered in dust.
If dust builds up on the mains plug, the resulting
humidity can damage the insulation, which could
result in fire. Pull the mains plug out from the mains
socket and wipe it with a dry cloth.
If not using the projector for an extended period of
time, pull the mains plug out from the mains socket.
Insert the mains plug securely into the mains socket.
If the plug is not inserted correctly, electric shocks or
overheating could result.
Do not use damaged plugs or loose mains socket.
Do not place the projector on top of surfaces which
are unstable.
If the projector is placed on top of a surface which is
sloped or unstable, it may fall down or tip over, and
injury or damage could result.
Do not place the projector into water or let it become
wet.
Failure to observe this may result in fire or electric
shocks.
Do not do anything that might damage the mains
lead or the mains plug.
Do not damage the mains lead, make any
modifications to it, place it near any hot objects, bend
it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
If the mains lead is used while damaged, electric
shocks, short-circuits or fire may result.
Ask an Authorised Service Centre to carry out any
repairs to the mains lead that might be necessary.
Do not place the projector on soft materials such as
carpets or sponge mats.
Doing so may cause the projector to overheat, which
can cause burns, fire or damage to the projector.
Do not place liquid containers on top of the
projector.
If water spills onto the projector or gets inside it, fire
or electric shocks could result.
If any water gets inside the projector, contact an
Authorised Service Centre.
Do not insert any foreign objects into the projector.
Do not insert any metal objects or flammable objects
into the projector or drop them onto the projector, as
doing so can result in fire or electric shocks.
Do not allow the + and - terminals of the batteries to
come into contact with metallic objects such as
necklaces or hairpins.
Failure to observe this may cause the batteries to
leak, overheat, explode or catch fire.
Store the batteries in a plastic bag and keep them
away from metallic objects.
Do not handle the mains plug with wet hands.
Failure to observe this may result in electric shocks.
6 - ENGLISH
Precautions with regard to safety
Do not touch the leaked liquid from the batteries.
If you touch the leaked liquid, it may hurt your skin.
Immediately wash away the liquid with water and
seek medical advice.
If you get the leaked liquid in your eye, it may cause
blindness or damage. Never rub your eye, and
immediately wash away the liquid with water and
seek medical advice.
During a thunderstorm, do not touch the projector or
the cable.
Electric shocks can result.
Do not use the projector in a bath or shower.
Fire or electric shocks can result.
Do not place your skin into the light beam while the
projector is being used.
Strong light is emitted from the projector’s lens. If you
place directly into this light, it can hurt or damage
your skin.
Do not look into the lens while the projector is being
used.
Strong light is emitted from the projector’s lens. If you
look directly into this light, it can hurt and damage
your eyes.
Be especially careful not to let young children look
into the lens. In addition, turn off the power and
disconnect the mains plug when you are away from
the projector.
Do not place your hands or other objects close to the
air outlet port.
Heated air comes out of the air outlet port. Do not
place your hands or face, or objects which cannot
withstand heat close to this port [allow at least
50 cm (20") of space], otherwise burns or damage
could result.
Replacement of the lamp is recommended to be
carried out by a qualified technician.
The lamp has high internal pressure. If improperly
handled, explosion might result.
The lamp can easily become damaged if struck
against hard objects or dropped, and injury or
malfunctions may result.
When replacing the lamp, allow it to cool for at least
one hour before handling it.
The lamp cover gets very hot, and touching it can
cause burns.
Before replacing the lamp, be sure to disconnect the
mains plug from the mains socket.
Electric shocks or explosions can result if this is not
done.
Do not allow infants or pets to touch the remote
control unit.
Keep the remote control unit out of the reach of
infants and pets after using it.
Important
Information
CAUTIONS
Do not cover the air inlet port or the air outlet port.
Doing so may cause the projector to overheat, which
can cause fire or damage to the projector.
Do not place the projector in narrow, badly ventilated
places such as closets or bookshelves.
Do not place the projector on cloth or papers, as
these materials could be drawn into the air inlet port.
Do not set up the projector in humid or dusty places
or in places where the projector may come into
contact with oily smoke or steam.
Using the projector under such conditions may result
in fire, electric shocks or plastic deterioration. The
plastic deterioration may cause the falling down of
the projector which is mounted on the ceiling.
Do not set up the projector in a high temperature
environment, such as near a heater or in direct
sunlight.
Failure to observe this may result in fire, malfunction
or plastic deterioration.
Do not set up the projector outdoors.
The projector is designed for indoor use only.
When disconnecting the mains lead, hold the plug,
not the lead.
If the mains lead itself is pulled, the lead will become
damaged, and fire, short-circuits or serious electric
shocks may result.
Always disconnect all cables before moving the
projector.
Moving the projector with cables still attached can
damage the cables, which could cause fire or electric
shocks to occur.
Do not place any heavy objects on top of the
projector.
Failure to observe this may cause the projector to
become unbalanced and fall, which could result in
damage or injury.
ENGLISH - 7
Information
Precautions with regard to safety
Important
Do not short-circuit, heat or disassemble the
batteries or place them into water or fire.
Failure to observe this may cause the batteries to
overheat, leak, explode or catch fire, and burns or
other injury may result.
When inserting the batteries, make sure the
polarities (+ and -) are correct.
If the batteries are inserted incorrectly, they may
explode or leak, and fire, injury or contamination of
the battery compartment and surrounding area may
result.
Use only the specified batteries.
If incorrect or different kinds of batteries are used,
they may explode or leak, and fire, injury or
contamination of the battery compartment and
surrounding area may result.
Do not mix old and new batteries.
If the batteries are inserted incorrectly, they may
explode or leak, and fire, injury or contamination of
the battery compartment and surrounding area may
result.
Remove the used batteries from the remote control
promptly.
If you leave used batteries in the remote control for
an extended period of time, it may cause liquid
leaking, abnormal internal temperature rising or
explosion.
If not using the projector for an extended period of
time, disconnect the mains plug from the mains
socket and remove the batteries from the remote
control.
If dust builds up on the mains plug, the resulting
humidity may damage the insulation, which could
result in fire.
Keeping or leaving the remote control with batteries
inside may cause insulation deterioration, electrical
leakage or explosion which could result in fire.
Do not put your weight on this projector.
You could fall or the projector could break, and injury
may result.
Be especially careful not to let young children stand
or sit on the projector.
Disconnect the mains plug from the mains socket as
a safety precaution before carrying out any cleaning.
Electric shocks can result if this is not done.
If the lamp has broken, ventilate the room
immediately. Do not touch or bring your face close
to the broken pieces.
Failure to observe this may cause the user to absorb
the gas which was released when the lamp broke and
which contains nearly the same amount of mercury
as fluorescent lamps, and the broken pieces may
cause injury.
If you believe that you have absorbed the gas or that
the gas has got into your eyes or mouth, seek
medical advice immediately.
Ask your dealer about the replacement of the lamp
unit and check the inside of the projector.
Ask an Authorised Service Centre to clean inside the
projector at least once a year.
If dust is left to build up inside the projector without
being cleaned out, it can result in fire or problems
with operation.
It is a good idea to clean the inside of the projector
before the season for humid weather arrives. Ask
your nearest Authorised Service Centre to clean the
projector when required. Please discuss with the
Authorised Service Centre regarding cleaning costs.
We are constantly making efforts to preserve and maintain a clean environment. Please take non repairable
units back to your dealer or a recycling company.
Cautions when transporting
Do not subject the projector to excessive vibration
or shocks.
The projector lens needs to be handled with care.
Cover the lens with the lens cover when transporting
the projector.
8 - ENGLISH
When transporting the projector, hold the body at
the bottom securely.
Do not hold the adjuster legs or the top cover to move
the projector, as this may damage the projector.
Cautions when installing
Precautions with regard to safety
Avoid setting up in places which are subject to
vibration or shocks.
The internal parts can be damaged, which may cause
malfunctions or accidents.
Avoid setting up in places which are subject to
sudden temperature changes, such as near an air
conditioner or lighting equipment.
The life of the lamp may be shortened or the projector
may be turned off. See “TEMP indicator” on page 45.
Do not set up the projector near high-voltage power
lines or near motors.
The projector may be subject to electromagnetic
interference.
Cautions on use
In order to get the best picture quality
Draw curtains or blinds over any windows and turn off
any lights near the screen to prevent outside light or
light from indoor lamps from shining onto the screen.
Do not touch the surfaces of the lens with your bare
hands.
If the surface of the lens becomes dirty from
fingerprints or anything else, this will be magnified
and projected onto the screen. Moreover, when not
using the projector, attach the lens cover.
Liquid crystal panel
Do not project the same image for long periods of
time, as this may remain as an afterimage on the
liquid crystal panel. Display the white screen test
pattern for more than an hour to remove it. See
“ZOOM/FOCUS” on page 40.
The liquid crystal panel of the projector is built with
very high precision technology to provide fine picture
details. Occasionally, a few stuck pixels may appear
on the screen as fixed points of blue, green or red. It
is recommended to switch off the projector once and
try after 1 hour later again. Please note that this does
not affect the performance of your LCD.
If installing the projector to the ceiling, ask a
qualified technician or an Authorised Service Centre
to carry out all installation work.
You will need to purchase the separate installation kit
(Model No. ET-PKE2000, ET-PKE1000S).
Furthermore, all installation work should only be
carried out by a qualified technician.
See “Ceiling mount bracket safeguards” on page 56
for the safety cable installation.
If using this projector at high elevations 1 400 2 700 m (4 593 - 8 858 ft) sea level, set the HIGH
ALTITUDE MODE to ON. See “HIGH ALTITUDE
MODE” on page 44.
Failure to observe this may result in malfunctions or
the life of the lamp or the other components may be
shortened.
The projector has a high pressure mercury lamp and
that is characterised as follows.
The brightness of the lamp depends on the duration
of use.
The lamp may explode or shorten the lamp life by
shocks or chipping damage.
The lamp may explode only occasionally after using
the projector.
The lamp may explode if using the projector after the
instructed lamp replacement timing.
When the lamp exploded, it emits the internal smoke-
like gas.
The lamp life depends on individual lamp
characteristics, usage condition and the installation
environment. Especially the consecutive use of the
projector for more than 10 hours, or the frequent
switching on or off may greatly affect on the lamp life.
Optical components
If you use the projector consecutively 6 hours every
day, the optical components may need to be replaced
in less than 1 year.
Important
Information
ENGLISH - 9
Information
Precautions with regard to safety
Important
Accessories
Make sure the following accessories are provided with your projector.
Remote control for
PT-AE3000E (x1)
N2QAYB000316
Safety cable
TTRA0141
Attachment screw (x1)
Safety cable (x1)
Mains lead for continental Europe (x1)
K2CM3FH00001
3 m (9'10")
AA batteries for remote control (x2) Power cord secure lock (x1)
Lens cover (x1)
TXFKK01VKF5
(Attached to the projector by default.)
Mains lead for UK (x1)
K2CT3FH00003
3 m (9'10")
TTRA0184
* The protectors for enclosed products, such as a plug
cover or foam cartons, must be treated properly.
* Contact to an Authorised Service Centre for lost
accessories.
10 - ENGLISH
About Your Projector
Remote control
Power button
While the MAIN POWER
button is on, switch between
standby mode and projection
mode. (page 21)
Display the PICTURE menu.
(page 23)
Switch to cycle through the
PICTURE MODE. (page 23)
Switch to cycle through the
aspect ratio. (page 24)
Display the main menu or
return to the previous menu.
(page 29)
Navigate through the
menus with FGIH,
and activate the menu
item with the ENTER
button. (page 29)
Remote control signal emitter
Emit remote control signal. (page 23)
Button backlight
When any button is pressed, the button
backlight is lit. Without any operation, it
gets darker after 5 seconds and goes of
after next 5 seconds.
Display the LENS CONTROL
menu. (page 23)
Preparation
Display the MEMORY LOAD
menu. (page 24)
Display the COLOUR
MANAGEMENT menu.
(page 26)
Display the input waveform.
(page 24)
Return to the previous
menu. (page 29)
Capture the projected image
as a still image. (page 28)
Reset some of the settings to
the factory default. (page 28)
Switch to cycle through
the input method.
(page 28)
Battery compartment
1. Press the tab and lift up the cover.
2. Insert the batteries according to the polarity diagram indicated
inside.
Activate the assigned
function from the menu
options for shortcut.
(page 42)
NOTE:
• Do not drop the remote control.
• Avoid contact with liquids or moisture.
• Use manganese batteries or alkaline batteries with the remote control.
• Do not attempt to modify or disassemble the remote control. Contact an Authorised Service Centre for repairs.
• Do not keep pressing the remote control buttons as this may shorten battery life.
• See “Remote control operation” on page 23.
ENGLISH - 11
About Your Projector
Projector body
J Top and front view
Air exhaust port
Preparation
Heated air comes out of
this opening.
Projection lens
Lens cover
Protects the projection lens
from dust or dirt.
Lens shift dial • Vertical
(page 16)
Remote control signal
receptor
(page 23)
Lens shift dial • Horizontal
(page 16)
Power/LAMP/TEMP
indicators
(page 20/page 45)
Air filter
(page 46)
MAIN POWER
Switch the projector on/off
(page 21)
Air exhaust port
Heated air comes
out of this opening.
INPUT SELECT
Switch to cycle through the
input method. (page 22)
Navigate through the menus with F G H I,
and activate the menu item with the ENTER
button. (page 29)
Power
While the MAIN POWER is on, switch between
standby mode and projection mode. (page 21)
MENU
Display the main menu.
Return to the previous menu. (page 29)
RETURN
Return to the previous menu.
(page 29)
(Push to open/close the cover.)
FOCUS and ZOOM
Adjust the focus and size of the
image. (page 22)
NOTE:
• Do not cover the ventilation openings or place anything within 50 cm (20") of them as this may cause damage or injury.
• While the projector is not in use, keep the lens cover to protect the lens.
12 - ENGLISH
J Back and bottom view
Security lock
Air intake port
Attach the commercial shackle lock
which is provided with the projector.
Compatible with the Kensington
MicroSaver Security System.
About Your Projector
Top cover
Hold the top cover at the back corner
and slightly push up to open.
(page 47)
Preparation
Air intake port
AC IN
Connect the mains lead to
supply electronic power to the
projector. (page 19)
Safety cable attachment point
Attach the safety cable when
mounted on the ceiling.
(page 56)
Screw up/down to adjust the
projection angle. (page 15)
Connecting
terminals
(page 18)
COMPUTER IN
Connect an RGB signal cable
from your PC.
HDMI IN
Connect HDMI signal cables.
Front leg adjusters
Screw up/down to adjust the
Lens cover attachment holeFront leg adjusters
COMPONENT IN
Connect YPBPR signal cables.
SERIAL
Connect a compatible cable for
controlling the projector
remotely via your computer.
(page 51)
projection angle. (page 15)
S-VIDEO IN
Connect a S-VIDEO
signal cable.
VIDEO IN
Connect an RCA
composite video cable.
NOTE:
• Do not cover the ventilation openings or place anything within 50 cm (20") of them as this may cause damage or injury.
• The projector should only be used with the attached mains lead to ensure optimum performance and avoid damage to the
projector.
• Do not open the top cover other than replacing the lamp unit.
ENGLISH - 13
Setting up
Screen size and throw distance
You can adjust the projection size with 2.0x zoom lens. Calculate and define the throw distance as follows.
S
SH
Projected image
(Shown as 16:9 size)
Getting Started
All measurements and the calculation results bellow are approximate and may differ from the actual measurements.
D
SW
Screen
Throw distance (16 : 9) Throw distance (2.35 : 1)
Screen Diagonal
(SD)
1.01 m (40") 1.2 m (3'11'') 2.3 m (7'6'') 1.3 m (4'3'') 2.5 m (8'2'')
1.27 m (50") 1.5 m (4'11'') 2.9 m (9'6'') 1.6 m (5'2'') 3.1 m (10'2'')
1.52 m (60") 1.8 m (5'10'') 3.5 m (11'5'') 1.9 m (6'2'') 3.7 m (12'1'')
1.77 m (70") 2.1 m (6'10'') 4.1 m (13'5'') 2.2 m (7'2'') 4.4 m (14'5'')
2.03 m (80") 2.4 m (7'10'') 4.7 m (15'5'') 2.6 m (8'6'') 5 m (16'4'')
2.28 m (90") 2.7 m (8'10'') 5.3 m (17'4'') 2.9 m (9'6'') 5.6 m (18'4'')
2.54 m (100") 3 m (9'10'') 5.9 m (19'4'') 3.2 m (10'5'') 6.3 m (20'8'')
3.05 m (120") 3.6 m (11'9'') 7.2 m (23'7'') 3.8 m (12'5'') 7.6 m (24'11'')
3.81 m (150") 4.5 m (14'9'') 9 m (29'6'') 4.8 m (15'8'') 9.5 m (31'2'')
5.08 m (200") 6 m (19'8'') 12 m (39'4'') 6.4 m (20'11'') 12.7 m (41'8'')
Minimum distance
(LW)
Maximum distance
(LT)
Minimum distance
(LW)
Maximum distance
(LT)
J Calculation methods for screen dimensions
You can calculate more detailed screen dimension from the screen diagonal.
16 : 9 size
Screen width (SW) and screen height (SH)
SW (m)= SD (m) x 0.872 SH (m) = SD (m) x 0.490
Minimum distance (LW) and maximum distance (LT)
LW (m) = SD (m) x 1.189 - 0.04 LT (m) = SD (m) x 2.378 - 0.05
2.35 : 1 size
Screen width (SW) and screen height (SH)
SW (m)= SD (m) x 0.920 SH (m) = SD (m) x 0.392
Minimum distance (LW) and maximum distance (LT)
LW (m) = SD (m) x 1.256 - 0.04 LT (m) = SD (m) x 2.512 - 0.05
NOTE:
• Do not use the projector at a raised or a horizontally tilted position as it may cause
malfunction of the projector.
• Make sure the projector lens surface is parallel with the screen. You can tilt the projector
body less than approximately ± 30° vertically. Overtilting may result in shortening the
component’s life.
• For the best quality of the projection image, install a screen where sun light or room light
does not shine directly onto the screen. Close window shades or curtains to block the lights.
14 - ENGLISH
+30°
-30°
Setting up
Projection method
You can use the projector with any of the following 4 projection methods. To set the desired method in the projector,
See “INSTALLATION” on page 44.
J Setting on a desk/floor and
projecting from front
INSTALLATION: FRONT/DESK INSTALLATION: REAR/DESK
J Setting on a desk/floor and
projecting from rear
J Mounting on the ceiling and
projecting from front
INSTALLATION: FRONT/CEILING INSTALLATION: REAR/CEILING
NOTE:
• A translucent screen is required for rear projection.
• When mounting the projector on the ceiling, the optional ceiling mount bracket (ET-PKE2000, ET-PKE1000S) is required.
• See “Ceiling mount bracket safeguards” on page 56.
J Mounting on the ceiling and
projecting from rear
Front leg adjusters and throwing angle
You can screw up/down the front leg adjusters to control the angle of the projector for adjusting the throwing angle.
See “Positioning the image” on page 22.
Getting Started
NOTE:
• Heated air comes out of the air exhaust port. Do not touch the air exhaust port directly.
• If keystone distortion occurs, see “KEYSTONE” on page 39.
• Screw up the adjuster legs, and an audible click will be heard as the limit.
ENGLISH - 15
Setting up
Lens shift and positioning
If the projector is not positioned at the right angle to the centre of the screen, you can adjust the projected image
position by moving the lens shift dials within the shift range of the lens.
J Adjusting the lens shift dials
Q Horizontal shift
You can place the projector where the projector lens is up to 40% horizontally off-centre from the screen and
then adjust the image position with the Lens shift dial • Horizontal.
Getting Started
Turning the dial clockwise:
Image moves to the right
Q Vertical shift
You can place the projector where the projector lens is up to 100% vertically off-centre from the screen and
then adjust the image position with the Lens shift dial • Vertical.
Up to about 40 %
of the projection
Up to about 40 %
of the projection
Turning the dial counterclockwise:
Image moves to the left
Up to about 100 %
of the projection
Up to about 100 %
of the projection
Turning the dial counterclockwise:
Image moves to the bottom
Turning the dial clockwise:
Image moves to the top
16 - ENGLISH
J Projector location range
You can determine where to locate the screen and the projector by considering the lens shift possibilities.
Q When the screen position is fixed
Setting up
Projector
V
Vertical centre of
screen
SH
Screen
SW
Q When the projector position is fixed
100%
H
Placement
Centre of lens
Getting Started
Shift range
100%
40% 40%
Projector
NOTE:
• When the projector is located at the right angle to the centre of the screen and the lens shift dials is centred, you will get
the best quality of the projection image.
• When the Lens shift dial • Vertical is at the vertical limit of the shift range, you cannot turn the dial to the horizontal limit,
likewise when the Lens shift dial • Horizontal is at the horizontal limit of the shift range, you cannot turn the dial to the
vertical limit.
• When the projector is tilted and you adjust KEYSTONE, the centre of the screen and the lens need to be realigned.
• Do not force the lens shift dials to turn as this may damage the projector. Turning the dials maximum limit is 4 or 5 times
from the default position.
ENGLISH - 17
Connections
Before connecting to the projector
Read and follow the operating and connecting instructions of each peripheral device.
The peripheral devices must be turned off.
Use cables that match each peripheral device to be connected.
Confirm the type of video signals. See “List of compatible signals” on page 50.
Audio cables must be connected from each peripheral device directly to the audio reproduction system.
Connecting example: COMPONENT IN/S-VIDEO IN/ VIDEO IN
\
Getting Started
To COMPONENT
video output
DVD player Video player DVD player
To VIDEO output
Connecting example: HDMI IN/COMPUTER IN
HDMI cable
(RP-CDHG100: Optional))
To HDMI output
To S-VIDEO output
RGB signal cable
(Commercial item)
NOTE:
• Make sure the HDMI cable is adapted to your HDMI device for proper performance.
• A compatible cable is required for an HDMI 1 080p signal.
• It is possible to connect with DVI devices via a HDMI/DVI conversion adapter, but some equipment may not project the
image properly or other problems could be encountered. See “Serial terminal” on page 51.
18 - ENGLISH
DVD player
Computer
Loading...