Panasonic NV-HV60 User Manual

Video Cassette Recorder

Model No.

NV-HV60 Series

Operating Instructions

Contents Page

Warning and Important Information 2

Controls and Components 3

Connections 5

Tuning the TV to Your VCR 6

Storing TV Broadcasts in Your VCR 7

Setting the Clock of Your VCR 9

Settings Using the On Screen Display 10

Option Setting 11

Playback 12

Recording 13

Timer Recording 16

Search Functions 19

Before Requesting Service 21

Specifications 23

VQT0B18

Before attempting to connect, operate or adjust this product, please read the instructions completely

Warning and Important Information

As this equipment gets hot during use, operate it in a well ventilated place; do not install this equipment in a confined space such as a book case or similar unit.

WARNING: To reduce the risk of fire, electric shock or product damage, do not expose this equipment to rain, moisture, dripping or splashing and ensure that no objects filled with liquids, such as vases, shall be placed on the equipment.

Important

Your attention is drawn to the fact that the recording of pre-recorded tapes or discs or other published or broadcast material may infringe copyright laws.

For your safety

Do not remove outer cover. Touching internal parts of the VCR is dangerous, and may seriously damage it. To prevent electric shock, do not remove cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel.

Inserting Remote Control Batteries

Insert the batteries with the polarity (+ and -) correctly aligned.

Notes:

The service life of the batteries is approximately 1 year. However, it varies considerably depending on the frequency of use.

• When they are exhausted, replace them with two AA, UM3, or R6 size batteries.

• When the batteries are exhausted, remove them immediately and dispose them correctly.

• Make sure that the batteries are inserted with the polarity (+ and -) correctly aligned.

• Do not mix old battery with new battery.

• Do not mix different battery types, i.e. Alkaline and Manganese.

• Do not use rechargeable (Ni-Cd) batteries.

• Do not heat or short-circuit the batteries.

• When you do not use the remote control for a long time, take out the batteries and store them in a cool, dry place.

Cautions before you operate this VCR

Avoid:

• Humidity and dust.

• Covering the ventilation holes with soft materials such as cloth or paper.

• Extreme heat such as direct sunlight.

• Magnets or electromagnetic objects.

• Touching internal parts of the VCR.

• Water or some other liquid.

• Lightning. (Disconnect the aerial plug from the VCR during lightning storms.)

• Anything heavy on the VCR.

• Connecting or handling the equipment with wet hands.

• Using a cell phone near the VCR because doing so may cause noise to adversely affect the picture and sound.

Do:

• Wipe the VCR with a clean and dry cloth.

• Install the VCR in a horizontal position.

• Keep the VCR, TV and other equipment switched off until you have finished all connections.

Condensation may form in the following cases:

• The VCR is brought from cold surroundings into a well-heated room.

• The VCR is suddenly brought from cool surroundings, such as an air-conditioned room or car, to a place which is hot and humid.

Note:

• In any of the above-mentioned conditions, do not operate the VCR for at least 1 hour. This VCR is not equipped with a dew sensor.

Press [VCR-ON/OFF] (1) to switch the VCR from on the standby mode or vice versa. In the standby mode, the VCR is still connected to the mains.

NV-HV60GL: Australian model NV-HV60GN: New Zealand model

Plug in Auto Tuning (NV-HV60GN only)

(Setting image illustration)

(1)

(3)

(2)

AUTO TUNING IN PROGRESS, PLEASE WAIT.

CH 22 SEARCH END: MENU

(1) Connect the aerial cable. (2) Connect the mains lead. (3) Press [VCR-ON/OFF] (1). (4) Plug in Auto Tuning is completed. ¢ On Screen Display

(4)

All broadcasting stations that can be received in the area are automatically tuned and stored in memory.

• Do not turn off the VCR halfway. (See page 7.)

OSD

REPEAT

VOLUME

PROG PLAY

PICTURE MODE

REC

VCR

DATE

GUIDE

CANCEL

DISPLAY

RESET

AUDIO

SPEED

++–+

–

ON OFF

–

PROG / CHECK

TIMER

NAVI

INDEX

123

7809

1 2 3 4

INPUT SELECT

JET REW

–

TRACKING/V-LOCK

–

VCR

123 4

JET REW

Í/I

(1)

(8) (5)

(38) (29) (39) (40) (32) (19)

(44) (43) (42) (24) (25) (26) (41) (45) (47) (46)

(48) (49) (50) (51)

(54) (53) (52)

(9)

AC IN ~

TAPE REFRESH PICTURE MODE

PROGPROG TIMER

GUIDE CHECK

PLAY

VIDEO

AUDIO

Controls and Components

IN (AV1) OUT

REC/OTR

JET REW

EJECT

STOP PLAY

OUT

TIMER REC

(36)

(35) (34)

(1)

(2)

(33)

(32)

(31) (3) (4) (5) (6)

(7)

(8)

(9)

(10) (11)

(12)

(13) (14)

(15)

(30)

(29)

(28)

(27)

(26)

(25)

(24)

(23)

(22)

(21)

(20)

(19)

(18)

(17)

(16)

(37)

VCR Operation

• Set [VCR/TV] switch (22) to [VCR]. (1) [VCR-ON/OFF] (2) [Numeric]

To select the programme positions (1-99).

19:

• Example:

To enter numbers for various settings.

(3) [AV] (4) [NAVI] (5) [PROG PLAY] (6) No function (7) [MENU] (8) [Rewind] (9) [Stop] (10) [ON] (11) [CH] (12) [DATE] (13) [GUIDE] (14) [PROG/CHECK] (15) [CANCEL] (16) [DISPLAY] (17) [RESET]

To reset the tape counter (elapsed time) to [0:00.00].

• The tape counter is automatically reset to [0:00.00] when a video cassette is inserted.

(18) [AUDIO] (19) [TIMER (REC)] (20) [SPEED] (21) [OFF] (22) [VCR/TV] switch (23) [OK] (24) [Fast Forward] (25) [Play] (26) [JET REW] (27) [REC] (28) [Pause/Slow] (29) [PICTURE MODE] (30) [INDEX] (31) [VOLUME] (32) [Channel]/[TRACKING/V-LOCK] (33) [INPUT SELECT] (34) [REPEAT] (35) [OSD] (36) Infra-red transmitter (37) [Cursor]

(38) [TAPE REFRESH] (39) Cassette compartment (40) [EJECT] (41) [REC/OTR] (42) VCR display (43) Infra-red Remote Control Receiver window (44) [TIMER CHECK] (45) [PROG GUIDE] (46) AUDIO IN sockets (AV 2) (47) VIDEO IN socket (AV 2) (48) AC Input socket (49) VIDEO IN socket (AV 1) (50) VIDEO OUT socket (51) RF IN socket (52) RF OUT socket (53) AUDIO OUT sockets (54) AUDIO IN sockets (AV 1)

TV Operation using the remote control

• Set [VCR/TV] switch (22) to [TV]. You can use [TV-ON/OFF] (1)*1, [Numeric] (2)*2, [AV] (3)*3,

[VOLUME] (31) for your TV operation. (See page 5.)

To switch the TV on from standby mode (OFF) or vice versa. On some TVs it is only possible to switch the TV to standby mode (OFF) with this button, but not on. In this case, try to turn the TV on with one of the following buttons: [Numeric] (2) [AV] (3) [Channel] (32)

To select the programme positions (1-99) on the TV.

To select desired AV input on the TV.

To adjust the volume of the TV.

To select the desired programme position (TV station) on the TV.

and [Channel] (32)*5 on the remote control

Setting the Remote Control to Operate

(1) Aerial (Not supplied) (2) TV Set (Not supplied) (3) Aerial Connector (4) RF IN socket (51) (5) RF OUT socket (52)

(6) AC Input socket (48) ¢ To mains supply

(1) Aerial (Not supplied) (2) TV Set (Not supplied) (3) Aerial Connector (4) VIDEO IN (5) AUDIO IN (6) AV Cable (Supplied) (7) RF IN socket (51) (8) RF OUT socket (52)

(9) VIDEO OUT (50)/

AUDIO OUT (53)

(10)AC Input socket (48) ¢ To mains supply

(1) Stereo amplifier (Not supplied) (2) REC (3) PLAYBACK (4) AUDIO OUT (53) (5) AUDIO IN (54)

¢ Audio Cables (Not supplied)

Your TV

You can operate the TVs of the manufacturers listed below with the remote control after setting it.

This setting procedure allows you to operate the TVs of some manufacturers using the supplied remote control.

Preparation

• Set [VCR/TV] switch (22) to [TV].

Operations 1 Find the manufacturer number of your TV while

referring to the following table.

2 While holding down [TV-ON/OFF] (1) on the remote

control, use [Numeric] (2) to enter the manufacturer number. This completes the settings for the TV manufacturer.

• Be sure to enter the number in two digits.

Example: 1 ) 01

3 To confirm the correct settings were made, check

whether the TV can be operated properly.

• When a manufacturer has multipled numbers in the following table, try entering other numbers if the TV operations cannot be performed properly, and then select the optimal number.

Notes:

• If you are using a Panasonic TV, this setting has already been made, and so you do not need to perform the above setting procedure. However, this remote control may not work with some Panasonic TVs.

• Some TV models cannot be operated using this remote control (including all TVs non-remote compatible).

List of TVs Compatible with the VCR Remote Control

[Brand] [Code]

Panasonic/National 01-04

SONY 05

TOSHIBA 06

JVC 07

HITACHI 08

MITSUBISHI 09, 10

SHARP 11

PHILIPS, SAMSUNG 12

Connections

This section shows you how to connect the VCR to an aerial, TV, etc.

When the VCR is turned on after unpacking and connecting the aerial cable and the mains lead, Plug in Auto Tuning starts automatically. (NV-HV60GN only)

Basic Connections

The following connections are required to record and play back the video cassette through the TV.

(1)

(3)

VIDEO

AC IN ~

AUDIO

(6)

IN (AV1) OUT

Connection to a TV using the Audio/Video Input Socket:

Set the RF output channel of the VCR to [ss] (RF OFF) when the VCR is connected to the TV via the Audio/Video cable. (See page 6.)

(3)

VIDEO

AC IN ~

AUDIO

(10)

IN (AV1) OUT

(9)

(4)

(2)

(6)

(5)

(4)

OUT

(5)

(1)

(7)

OUT

(8)

NEC 13

SANYO 14

GOLDSTAR/LG 15, 16

SAMSUNG 17,18

SANYO 19

Connection to a Stereo Amplifier:

(2)

VIDEO

AC IN ~

AUDIO

IN (AV1) OUT

(3)

(4)(5)

(1)

Tuning the TV to Your VCR

During Plug in Auto Tuning After Plug in Auto Tuning

Example for NV-HV60GL Example for NV-HV60GN

…

(RF OFF)

The VCR supplies a signal to the TV via the RF coaxial cable on channel AU28-69 or NZ21-69. It is possible to view the video picture on your TV in the same way that you watch TV broadcasts. If you have connected the VCR to the TV through the Audio/ Video input sockets, then you do not need to follow the procedure below.

For NV-HV60GL/Australia

Preparation

• Turn on the TV and the VCR.

Operations 1 Hold down [MENU] (7) for 5 seconds or more.

2 Set the TV to an unused position which you wish to

use for your video playback.

• Tune the TV until the display shown on the right appears on the screen. (Please refer to the TV manufacturers operating instructions regarding tuning.)

3 Press [MENU] (7).

For NV-HV60GN/New Zealand

When the VCR is turned on after unpacking and connecting the aerial cable and the mains lead, Plug in Auto Tuning starts automatically.

Notes:

• If the VCR is turned on with the aerial not connected, all channels are skipped. Therefore, firmly connect the aerial and then turn the VCR off and on again to execute Plug in Auto Tuning.

• When Auto Tuning is cancelled halfway, Auto Tuning is not executed even if the VCR is turned off and then turned on again. In this case, see page 7 [To Restart Plug in Auto

Tuning].

Preparation

• Turn on the TV and the VCR.

Operations 1 Set the TV to an unused position which you wish to

use for your video playback.

• Tune the TV until the display shown below appears on the screen. (Please refer to the TV manufacturers operating instructions regarding tuning.)

AUTO TUNING IN PROGRESS, PLEASE WAIT.

CH 22 SEARCH END: MENU

Panasonic VCR

END: MENU

AUTO TUNING IS COMPLETED.

END: MENU

To Change the RF output Channel

In some rare cases after tuning the TV to your VCR, interference may be visible on the picture. To get rid of this interference, you can manually adjust the RF output channel a few channels up and down from the current setting. The procedure is described below.

Operations 1 Hold down [MENU] (7) for 5 seconds or more.

• The VCR display changes as shown below and the VCR picture on the TV displays this pattern.

Panasonic VCR

END: MENU

2 Enter the desired channel number (AU28-69, NZ21-69)

by [Numeric] (2) or [Channel] (32).

• Ensure that [VCR/TV] switch (22) is set to [VCR].

• Set the RF output channel of the VCR to [ss] (RF OFF) when the VCR is connected to the TV via the Audio/Video cable. Press [Channel] (32) to display [ss].

NV-HV60GL:

NV-HV60GN:

• It is also possible to select by pressing [Numeric] (2)

2 8

Example:

28:

3 Press [MENU] (7) to finish the setting mode.

4 Retune your TV to the new RF channel for the VCR.

Note:

• Even if the RF output channel has been changed, it is not necessary to perform Auto Tuning.

2 Press [MENU] (7).

Storing TV Broadcasts in Your VCR

During Plug in Auto Tuning After Plug in Auto Tuning

SELECT END

: , OK :MENU

CLOCK SET TUNER PRESET SYSTEM OPTION

CH 1 CLEAR [OFF] AUTO TUNE SEARCH [3] FINE

END :MENU

SELECT:

TUNER PRESET

CH 1

END: MENU

100

AUTO TUNING IN PROGRESS, PLEASE WAIT.

SELECT END

: , OK :MENU

CLOCK SET TUNER PRESET SYSTEM OPTION

The number displayed here is the number of channels still to be auto tuned.

The VCR is fitted with its own tuner (just like a normal TV) and can be preset to receive up to 99 TV broadcast stations.

Pre-programmed TV Channels (NV-HV60GL/Australia)

The local TV broadcast channels 2, 7, 9, 10 and 28 are factory-preset in this VCR.

That is, if you can receive television broadcasts on VHF channels 2, 7, 9, 10 and UHF channel 28, these are already tuned on the programme positions with the matching numbers. However, it is possible to cancel these settings and tune the local TV broadcast channels to any desired programme position.

Plug in Auto Tuning (NV-HV60GN/New Zealand)

When the VCR is turned on after connecting the aerial cable and the mains lead, Auto Tuning starts.

Auto Tuning Using the On Screen Display

Introduction

The VCR is tuned automatically by Plug in Auto Tuning. However, Auto Tuning using the On Screen Display should be performed according to the following method if necessary.

Preparations

• Confirm that the TV is on and the VCR viewing channel is selected.

• Turn on the VCR and select any programme position except A1 or A2.

• Set [VCR/TV] switch (22) to [VCR].

Operations 1 Press [MENU] (7) to display

the Main menu on the TV screen.

2 Press [Cursor] (37) (34) to

select [TUNER PRESET] then press [OK] (23).

Auto tuning searches for TV stations from VHF minimum to UHF maximum and memorizes every tuned programme position.

• If you turn the VCR off during Auto Tuning, Auto Tuning will stop halfway.

• If the VCR starts playback during Auto Tuning, Auto Tuning will stop halfway.

To Cancel Auto Tuning Mid-Operation:

Press [MENU] (7) during Auto Tuning. Auto Tuning is cancelled.

To Restart Plug in Auto Tuning: 1 Press [EJECT] (40) and remove the video cassette.

2 Keep both [Channel] (32) I and J on the VCR

pressed simultaneously for 3 seconds or more during the VCR on.

• The channel displayed on the VCR display disappears for a moment then changes to 1.

3 Disconnect the mains lead and then reconnect it.

4 Turn off the VCR and then turn it on.

• Auto Tuning commences.

If Auto Tuning stops halfway by turning the VCR off or a power failure: 1 Disconnect the mains lead and then reconnect it. 2 Turn off the VCR and then turn it on.

• Auto Tuning commences.

AUTO TUNING IN PROGRESS, PLEASE WAIT.

CH 22 SEARCH END: MENU

Disappears 1

AUTO TUNING IS COMPLETED.

END: MENU

3 Press [Cursor] (37) (34) to

select [AUTO TUNE] then press [Cursor] (37) (21) to start the Auto Tuning.

• When Auto Tuning is completed, the On Screen Display disappears and programme position 1 is selected.

Channels that can be Received

VHF UHF CATV

NV-HV60GL 0-12 28-69 45-470MHz

NV-HV60GN 1-11 21-69 45-470MHz

Notes:

• Auto Tuning searches for TV stations from VHF minimum to UHF maximum and memorizes every tuned programme position. Other programme positions are skipped.

• Auto Tuning takes five or more minutes to complete its search.

• If the VCR is not correctly tuned by Auto Tuning, follow the procedure on page 8.

Manual Tuning Procedure

1 Press [MENU] (7) to display the Main menu on the TV

screen.

2 Press [Cursor] (37) (34) to select [TUNER PRESET]

then press [OK] (23).

3 Press [Cursor] (37) (34) to select [CH] then select the

channel number you want to tune by pressing [Cursor] (37) (21).

4 Confirm that [CLEAR] is set to [OFF].

5 Press [Cursor] (37) (34) to select [SEARCH] then

press [Cursor] (37) (21) to start the Manual Tuning.

• If the desired TV station has not been tuned, press

[Cursor] (37) (21) again.

• Press [MENU] (7) and repeat steps 3-5 for each

programme position you want to tune to a station.

Direct Tuning

Follow steps 1 to 3 of Manual Tuning Procedure.

4 Confirm that [CLEAR] is set to [OFF].

5 Press [Cursor] (37) (34) select [SEARCH].

6 Press [Numeric] (2) to enter the number of the desired

programme position.

For the 5A and 9A channels, input the following numbers:

90 for CH-5A, 91 for CH-9A. (Example for NV-HV60GL.)

• For other channels that require tuning, repeat steps 3-6.

7 Press [MENU] (7) twice to exit the On Screen Display.

Fine Tuning Procedure

Follow steps 1 to 3 of Manual Tuning Procedure.

4 Press [Cursor] (37) (34) to select [FINE] then press

[Cursor] (37) (21) to obtain the best tuning condition.

• Press [OK] (23) to return the tuning to its former state.

CH 2

END: MENU

CH 2 SEARCH 74

END: MENU

6 Press [MENU] (7) three times to exit the On Screen

Display.

CH 2 AFC: OK

FINE : END: MENU

5 Press [MENU] (7) to exit the On Screen Display.

Blanking of Unused Programme Positions

Follow steps 1 to 3 of Manual Tuning Procedure.

4 Press [Cursor] (37) (34) to select [CLEAR] then

press [Cursor] (37) (21) to select [ON].

• Repeat steps 3-4 for other unused programme positions to skip during the selection of programme positions.

• To cancel the blanking of a programme position select that programme position then set [CLEAR] to [OFF].

5 Press [MENU] (7) twice to exit the On Screen Display.

+ 16 hidden pages