PANASONIC LIAC14IM6 User Manual [de, en, es]

Operating Instructions

ENGLISH

2 ~ 9

FRANÇAIS

10 ~ 17

18 ~ 25

26 ~ 33

TIMER OUTDOOR

ACTUAL

HEATER

HEAT

TIMER

234 56

BOOSTER

MONTUEWEDTHUFRISAT SUN

TANK

QUIET

SETTING

OFF

HEATER

STATUS

SOLAR REMOTE

FORCE

NOT AVAILABLE

PUMPDW

OPERATION

WATER OUTLET

/ ON

OFF

0.2

0.30.1

0.40

MPa

ENGLISH

Before operating the unit, read these operating instructions thoroughly and keep them for future reference. Before operating the unit, make sure the installation has been carried out correctly by authorized dealer correctly and precisely following the installation instructions given.

FRANÇAIS

Avant d’utiliser l’appareil, lisez ce mode d’emploi dans son intégralité et conservez-le pour toute référence ultérieure. Avant de faire fonctionner l’unité, assurez-vous que l’installation a été correctement réalisée par un revendeur agréé et dans le strict respect des consignes d’installation fournies.

Air-to-Water Heatpump

Model No. Indoor Unit

LIAC12IM6 LIAV12IM LIAC14IM6 LIAV14IM LIAC16IM6 LIAV16IM

Outdoor Unit

2 ~ 9

10 ~ 17

ESPAÑOL

Antes de utilizar la unidad, sírvase leer atentamente estas instrucciones de funcionamiento y conservarlas como futuro elemento de consulta. Antes de operar la unidad asegúrese de que la instalación haya sido realizada correctamente por un distribuidor autorizado, siguiendo de forma correcta y precisa las instrucciones de instalación dadas.

DEUTSCH

Bevor Sie das Gerät in Betrieb nehmen, lesen Sie bitte diese Bedienungsanleitung aufmerksam durch und bewahren Sie sie für die künftige Verwendung auf. Vor der Inbetriebnahme dieses Geräts ist sicherzustellen, dass die Montage durch einen autorisierten Händler fachgerecht entsprechend der Installationsanleitung durchgeführt wurde.

18 ~ 25

26 ~ 33

F567486

TABLE OF CONTENTS

NOTE

OPERATION CONDITION

WARNING

CAUTION

WARNING

TABLE OF CONTENTS

SAFETY PRECAUTIONS

CONTROL PANEL

INDOOR UNIT

TROUBLESHOOTING

2~3

4~7

SAFETY PRECAUTIONS

• This manual describes how to operate the Heatpump system between indoor and outdoor units only.

•

Other operation such as water tank, radiator, external thermo controller and underﬂ oor system, please refer to respective manufacturer operation manuals.

To prevent personal injury, injury to others, or property damage, please comply with the following. Incorrect operation due to failure to follow instructions below may cause harm or damage, the seriousness of which is classiﬁ ed as below:

WARNING

CAUTION

The instructions to be followed are classiﬁ ed by the following symbols:

This sign warns of death or serious injury.

This sign warns of injury or damage to property.

This symbol denotes an action that is PROHIBITED.

INFORMATION

34~35

NOTE

The illustrations in this manual are for explanation purposes only and may differ from the actual unit. It is subjected to change without notice for future improvement.

OPERATION CONDITION

Water outlet

Temperature (°C)

HEATING

Ambient

Temperature (°C)

HEATING

NOTICE :

When the outdoor temperature

Max. 55

Min. 25

Max. 35

Min. -20

Indoor

Outdoor

is out of the above temperature range, the heating capacity will drop signiﬁ cantly and outdoor unit might stop for protection control.

These symbols denote an actions that is COMPULSORY.

WARNING

INDOOR UNIT AND OUTDOOR UNIT

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Please consult authorized dealer or specialist to repair, install, remove and reinstall the unit. Improper installation and handling will cause leakage, electric shock or ﬁ re.

Do not install the unit in a potentially explosive or ﬂ ammable atmosphere. Failure to do so could result in ﬁ re.

Do not insert your ﬁ ngers or other objects into the air conditioner indoor or outdoor unit, rotating parts may cause injury.

Do not touch the outdoor unit during lightning, it may cause electric shock.

Do not attempt to repair the unit by yourself. Otherwise, it may cause injury if it is mishandling.

Do not install the indoor unit at outdoor. This is designed for indoor installation only.

CAUTION

not inspect or service the control panel by

yourself. Please consult authorized dealer.

WARNING

POWER SUPPLY

Do not use modiﬁ ed cord, joint cord, extension cord or unspeciﬁ ed cord to prevent overheating and ﬁ re.

Do not share the same power outlet with other equipment to prevent overheating and ﬁ re.

Do not operate with wet hands to prevent electric shock.

If the supply cord is damage, it must be replaced by the manufacturer, its service agent or similarly qualiﬁ ed persons in order to avoid a hazard.

This unit is equipped with Residue Current Circuit Breaker (RCCB). It is strongly recommended to check the operation of the RCCB after installation and periodically after servicing or maintenance by authorized dealer to ensure it is in good working order. Otherwise, it may cause electrical shock or ﬁ re in case of malfunction.

It is recommended to wear gloves during servicing or maintenance in order to avoid hazard.

This equipment must be earthed to prevent electrical shock or ﬁ re.

In case of emergency or abnormal conditions (burnt smell, etc), turn off the power supply, and please consult authorized dealer.

Prevent electric shock by switching off the power supply when:

- Before cleaning or servicing.

- Extended non-use.

- Abnormally strong lightning activity. This appliance is for multiple uses. All power

supply circuits must be turn off before access to any of the terminals in the indoor unit, to avoid electrical shock, burn or fatal injury.

CAUTION

INDOOR UNIT AND OUTDOOR UNIT

Do not wash the indoor unit with water, benzene, thinner or scouring powder.

Do not install the unit close to any combustible equipment or at bathroom. Otherwise, it may cause electric shock or ﬁ re.

Do not touch the water discharge pipe at the indoor unit during operation.

Do not place anything on top or beneath of the unit.

Do not sit or step on the unit, you may fall down accidentally.

Do not touch the sharp aluminium ﬁ n, sharp parts may cause injury.

Ensure drainage pipe is connected properly. Otherwise, leakage may occur.

Check the installation rack periodically to make sure that it is not damaged. After long periods of use, the strength of the installation rack may have deteriorated.

CONTROL PANEL

Do not let the control panel get wet. Otherwise, it may cause electric shock or ﬁ re.

Do not press the buttons on the control panel with hard, pointed objects. Otherwise, it may damage the unit.

Do not wash the control panel with water, benzene, thinner or scouring powder.

not inspect or service the control panel by

Do yourself. Please consult authorized dealer. Otherwise, it may cause injury if mishandling.

ENGLISH

Indoor Unit

Outdoor Unit

Power Supply

Control Panel

Water Tank Unit

Panel

Floor Heating

CONTROL PANEL

• Some functions described in this manual may not be applicable to your unit.

• Consult your nearest authorized dealer for further information.

• For normal operation, the

ERROR RESET

FORCE

and

PUMPDW

buttons are not in use.

13 14 15 16

1 2

OFF/ON Button

Operation LED

Operation Mode Button

Quiet Operation Button

Indoor Unit Backup Heater Operation Button

System Setting Mode Buttons

Timer Setting Group Buttons

Force Heater Mode Button

System Pumpdown Mode Button

System Status Check Mode Buttons

Error Reset Button

Heat Mode OFF/ON Indicator

Tank Mode OFF/ON Indicator

HEAT

TANK

QUIET

HEATER

FORCE

OPERATION

TIMER

OFF/ON

TIMER OUTDOOR

TIMER

2 3 4 56

MONTUE WEDTHU FRI SAT SUN

ON OFF

REMOTE

WATER OUTLET

OFF

SETTING

SET

MODE

SELECT

QUIET

ERROR

CANCEL

RESET

6 11

14 15 16 17 18 19 20 21 22 23 24 25

17 18

ACTUAL

HEATER BOOSTER

SETTING STATUS PUMPDW

19 20

CHECK

HEATER

STATUS

PUMPDWFORCECLOCK

Quiet Operation OFF/ON Indicator

Backup Heater Request OFF/ON Indicator

Force Heater Request OFF/ON Indicator

Backup Heater Actual Operation (OFF/ON) Indicator

Booster Heater Actual Operation (OFF/ON) Indicator

System Setting Mode OFF/ON Indicator

System Status Check Mode OFF/ON Indicator

System Pumpdown Mode OFF/ON Indicator

Timer/Clock Setting Display

Remote Display

Outdoor Ambient Temperature Display

Water Outlet Temperature Display

CONTROL PANEL PREPARATION

Setting Current Day and Time

CLOCK

1. Press

2. Press

3. Press

4. Repeat steps 2 and 3 to set the current time.

or to set current day.

SET

to conﬁ rm.

Notes:

• The current day and time need to be set when:

- The power is turned on for the ﬁ rst time.

- After a long time has elapsed since the power was last turned on.

• The current time that has been set will be the standard time for all the Timer operations.

SETTING UP THE SPECIAL FUNCTIONS

• After initial installation, you can manually adjust the settings. The initial setting remains active until the user changes it.

• The control panel can be used for multiple installations. Some functions may not be applicable to your unit.

SETTING

SELECT

CANCEL

1. Press

2. Press

3. Press

4. Press

5. Press

Day display

HEAT

TANK

QUIET

HEATER

FORCE

OPERATION

TIMER OUTDOOR

MON TUE WEDTHU FRI SAT SUN

YES / NO / Temperature display

REMOTE

WATER OUTLET

ACTUAL

HEATER BOOSTER

SETTING STATUS PUMPDW

SETTING / STATUS indicatorFunctions*Timer display

STATUS

SET

CHECK

SELECT FUNCTIONS AND SET YOUR DESIRED TIMER

SET

CHECK

and

simultaneously for 5 seconds to enter special setting mode. “SETTING” and “STATUS” indicator is ON.

or to browse functions.

SELECT

to enter the function.

or to enable YES or disable NO function, or set your desired day and time.

SET

to conﬁ rm.

ENGLISH

Display Function *

External Thermo Controller (YES / NO) To set external thermo controller connection.

Tank Connection (YES / NO) To set tank connection.

Heating Priority (YES / NO) To choose the heat pump only use for Heating side during HEAT + TANK mode.

Heating Heat-up Interval Set To set timer for Heating during HEAT + TANK mode (0.5hour ~ 10hours).

Tank Heat-up Interval Set To set timer for Tank during HEAT + TANK mode (5minutes ~ 1hour 35minutes).

Booster Heater Delay Time Set To set delay timer for booster heater to ON if tank temperature is not reached (20minutes ~ 1hour 35minutes).

Sterilization (YES / NO) To set sterilization, if required.

Sterilization Day & Time Set To set timer for sterilization (only once a week).

Sterilization Temperature Set To set temperature for sterilization function (40°C ~ 75°C).

Sterilization Continue Time To set timer to maintain heating temperature in order to complete the sterilization function (5minutes ~ 1hour).

BASIC OPERATION

CANCEL

ADVANCE OPERATION

OFF

TO TURN ON OR OFF THE UNIT

• When unit is ON, operation LED is lit and the actual temperature for water outlet and outdoor ambient are shown on the control panel display.

MODE

TO SELECT OPERATION MODE

HEAT HEAT +TANK TANK

• HEAT MODE

- To turn ON or OFF the panel/ﬂ oor heating operation.

- In this mode, the outdoor unit will provide heating

capacity to the indoor unit.

• HEAT + TANK MODE

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank and indoor unit.

- This operation is not used when the sanitary water

tank is not installed.

• TANK MODE

- To turn ON or OFF the sanitary tank operation.

- In this mode, the outdoor unit will provide heating

capacity to the sanitary tank.

QUIET

TO ENJOY QUIET ENVIRONMENT

• This operation reduces outdoor unit noise. In this condition, it may cause decrease in heating capacity.

HEATER

BACKUP HEATER OPERATION

• The backup heater provides extra heating capacity during cold outdoor temperature and only can operated at heat mode operation for indoor unit.

• The backup heater will automatically turn ON when the setting conditions is fulﬁ lled.

• To cancel the Heater operation manually, press the respective button again.

STATUS

CHECK

SYSTEM STATUS CHECK MODE

CHECK

1. Press

2. Press or to check the Compressor Running Frequency or Error History.

for 5 seconds to enter STATUS mode.

• Press

to exit STATUS mode.

• Once STATUS mode is entered, “STATUS” indicator is ON.

• STATUS mode cannot be activated when the “SETTING” indicator is ON.

• It is strongly recommended to contact the nearest authorized dealer to change the water temperature range.

• Using the control panel could set the temperature range for water outlet temperature and outdoor ambient temperature.

SYSTEM SETTING MODE

Operation Mode Temperature display

1. Press

TIMER OUTDOOR

HEAT

TANK

QUIET

HEATER

FORCE

OPERATION

Parameter *

SET

for 5 seconds to enter “SETTING” mode.

WATER OUTLET

SETTING indicator

ACTUAL

HEATER BOOSTER

SETTING STATUS PUMPDW

“SETTING” indicator is ON.

2. Press

3. After selecting the desired parameter, press

or to choose a parameter.

SELECT

enter the parameter.

4. Press

5. Press

or to set the desired temperature.

SET

again to conﬁ rm the setting.

• Repeat steps 2 to 5 to set other parameters.

Mode Parameter *

HEAT Outdoor ambient set temperature at low

water outlet temperature (-15°C ~ 15°C).

HEAT Outdoor ambient set temperature at high

water outlet temperature (-15°C ~ 15°C).

HEAT Water outlet set temperature at low outdoor

ambient temperature (25°C ~ 55°C).

HEAT Water outlet set temperature at high outdoor

ambient temperature (25°C ~ 55°C).

HEAT Set temperature for turning OFF heating

operation (5°C ~ 35°C).

HEATER Outdoor ambient set temperature for turning

ON heater operation (-15°C ~ 20°C).

TANK Sanitary tank set temperature

(40°C ~ 75°C).

WATER TEMPERATURE THERMO SHIFT SETTING

Ensure the operation LED is in OFF condition before setting.

SET

1. Press

within 5 seconds.

• Repeat steps 3 to 5 to set the desired shift temperature

(-5°C ~ 5°C).

Notes:

• Press

• The setting temperature will be stored in the system

once conﬁ rm.

• “SETTING” mode cannot be activated when the

“PUMPDW” and “STATUS” indicator is ON.

or wait 30 seconds to exit “SETTING” mode.

WEEKLY TIMER SETTING

Timer Display

Lights up if Timer operation is selected

TIMER

2 3 4 5 6

MON TUEWEDTHU FRI SAT SUN

ON OFF

ON Timer To automatically switch “ON” the unit

Day to be selected

Function Step

Enter timer mode

Set day & time

Press

Press or to select your desired day.

2. Press

3. “1” will be blinking, press

4. Press

5. Press or to select your desired time. If you want to set the timer together with other operations, press

6. Press

• After 2 seconds, the display will move to the next program.

7. Repeat steps 4 to 7 to set programs 2 to 6.

• During timer setup, if no button is pressed within 30 seconds, or if the setting at that moment is conﬁ rmed and timer setup is ended.

Add/Modify timer

Disable timer

Enable timer

Check timer

Repeat the steps above.

Press

1. Press

2. Press or until your desired day is shown, press

3. Press or to check the set programs.

Cancel timer

1. Press

2. Press or until your desired day is shown.

3. Press

4. Press

5. Press

6 different programs can be set in a day (1 ~ 6)

Indicates the selected day Indicates the next timer operation day

Time to be selected (10 minutes step)

OFF Timer To automatically switch “OFF” the unit

TIMER

SELECT

to conﬁ rm

OFF/ON

SELECT

to set program 1.

TIMER

OFF/ON

CLOCK

to select ON or OFF timer.

SET

to conﬁ rm program 1. The selected day will be highlighted with ▼.

TIMER

, then press

CANCEL

SET

SELECT

to conﬁ rm your selection.

TIMER

SELECT

to enter program setting.

or until your desired program is shown.

CANCEL

to cancel the program.

MODE

SETTING

SELECT

CANCEL

and

SET

QUIET

button is pressed the

ENGLISH

Notes:

• You can set the Timer for each day of the week (Monday to Sunday) with 6 programs per day.

• ON Timer can be set together with your desired temperature and this temperature will be used continuously.

• Same timer program cannot be set in the same day.

• You may also select collective days with same timer setting.

• Promotes energy saving by allowing you to set up to 6 programs in any given day.

INDOOR UNIT

WATER PRESSURE GAUGE

CLEANING INSTRUCTIONS

HINT

NON SERVICEABLE CRITERIAS

• Switch off the power supply before cleaning.

CAUTION

CLEANING INSTRUCTIONS

• Do not use benzene, thinner or scouring powder.

• Use only soap (

• Do not use water hotter than 40°C.

pH7) or neutral household detergent.

TIMER OUTDOOR

ACTUAL

HEATER

HEAT

TIMER

234 56

BOOSTER

MONTUEWEDTHUFRISAT SUN

TANK

QUIET

SETTING

OFF

HEATER

STATUS

SOLAR REMOTE

FORCE

NOT AVAILABLE

PUMPDW

OPERATION

WATER OUTLET

/ ON

OFF

0.2

0.30.1

0.40

MPa

HINT

• To ensure optimal performance of the unit, cleaning maintenance has to be carried out at regular intervals. Please consult authorized dealer.

WATER PRESSURE GAUGE

0.2

0.30.1

0.40

MPa

• Do not press or hit the glass cover with hard, pointed objects. This may damage the unit.

• Ensure that the water pressure is between 0.05 to

0.2MPa.

• In case the water pressure is out of the above range, please consult authorized dealer.

INDOOR UNIT & CONTROL PANEL

• Do not splash water directly.

• Wipe the unit gently with a soft, dry cloth.

OUTDOOR UNIT

• Do not obstruct the air inlet and air outlet vents, it may cause low performance or breakdown. Please remove obstacles to assure the ventilation.

• During winter, please clean and remove the snow near outdoor unit so that the snow does no cover the air inlet and air outlet vents.

INSPECTION

• In order to ensure optimal performance of the unit, seasonal inspections on the unit and ﬁ eld wiring have to be carried out at regular intervals. This maintenance should be carried out by authorized dealer.

• Clear any obstruction at the air inlet and air outlet vents of outdoor unit.

FOR EXTENDED NON-USE

• Turn off the power supply.

NON SERVICEABLE CRITERIAS

TURN OFF POWER SUPPLY then please consult authorized dealer under the following conditions:

• Abnormal noise during operation.

• Water/foreign particles have entered the control panel.

• Water leaks from Indoor unit.

• Circuit breaker switches off frequently.

• Power cord becomes unnaturally warm.

TROUBLESHOOTING

The following symptoms do not indicate malfunction.

SYMPTOM

CAUSE

Check the following before calling for servicing.

SYMPTOM

CHECK

The operation LED blinks and error code appear on control panel display.

Force Heater Mode Button

The following symptoms do not indicate malfunction.

SYMPTOM

Flowing sound during operation. ► • Refrigerant ﬂ ow inside the unit. Operation is delayed a few minutes after restart. ► • The delay is a protection to the unit’s compressor. Outdoor unit emits water/steam. ► • Condensation or evaporation occurs on pipes. Outdoor unit emits steam during heating mode. ► • This is due to defrost operation happens at the heat

exchanger.

Outdoor unit does not operate. ► • When the outdoor temperature is out of the operation

condition range, the heatpump system enter protection control.

System difﬁ cult to heat-up. ► • When heating is operated by indoor unit together with

ﬂ oor heating or panel heater simultaneously, there may be case where warm water temperature is getting lower and cause ﬂ oor heating or panel heater heat-up is weaken.

• When outdoor air temperature is low, it may be difﬁ cult to get warm.

• Is the snow pile blocking the discharge outlet or intake inlet of outdoor unit.

• When water outlet set temperature is low, it may be difﬁ cult to get warm.

System cannot get warm instantly. ► • Due to the nature of the heatpump system, it may take

some time to heat-up the water if the unit is operated from cold-start.

Operation starts after power resumes. ► • Unit is operates under auto restart function.

Check the following before calling for servicing.

SYMPTOM

Heating operation is not working efﬁ ciently. ► • Set the temperature correctly.

• Is the panel heater valve closed.

• Clear any obstruction at the air inlet and air outlet vents of outdoor unit.

Noisy during operation. ► • Check if the unit has been installed at an incline or the

cover is not closed properly.

The unit does not work. ► • Check if the circuit breaker is tripped. Operation LED is no lit or control panel display

► • Is the power supply off or power failure.

is blank.

CAUSE

CHECK

ENGLISH

The operation LED blinks and error code appear on control panel display.

TIMER

2 3 4 5 6

MON TUEWEDTHU FRI SAT SUN

ON OFF

Force Heater Mode Button

FORCE

• Turn the unit off and reveal the error code to authorized dealer.

• Timer operation cancel when error code occur.

• In case of a failure of the Air-to-Water Heatpump system, the backup heater can be used to heat up the heating water. Press

OFF

• Press

to stop the force heater operation.

FORCE

to switch on the backup heater.

• During Force Heater mode, all other operations are not allowed.

CONSIGNES DE SÉCURITÉ

TABLE DES MATIÈRES

REMARQUE

CONDITION D’UTILISATION

AVERTISSEMENT

ATTENTION

AVERTISSEMENT

UNITÉ INTÉRIEURE ET UNITÉ EXTÉRIEURE

TABLE DES MATIÈRES

CONSIGNES DE SÉCURITÉ

10~11

PANNEAU DE COMMANDE

12~15

UNITÉ INTÉRIEURE

DÉPANNAGE

INFORMATIONS

34~35

REMARQUE

Les illustrations de ce mode d’emploi sont fournies à titre d’exemple uniquement et peuvent présenter des différences par rapport à l’appareil proprement dit. Celui-ci peut être modiﬁ é sans préavis à des ﬁ ns d’amélioration.

CONDITION D’UTILISATION

Température de

sortie d’eau (°C)

CHAUFFAGE

Température

ambiante (°C)

CHAUFFAGE

Max. 55

Min. 25

Max. 35

Min. -20

Unité

intérieure

Unité

extérieure

ATTENTION: Si la température extérieure sort

de la plage de températures ci-dessus, la capacité thermique chutera de façon importante et il se peut que l’unité extérieure s’arrête pour le contrôle de protection.

• Ce manuel décrit comment utiliser le système de pompe à chaleur entre les unités intérieure et extérieure seulement.

• Pour le fonctionnement d’autres systèmes tels que le réservoir d’eau, le radiateur, le contrôleur thermique externe et le chauffage au sol, référez-vous aux modes d’emploi de leurs fabricants respectifs.

Pour éviter des blessures corporelles sur vous-même et sur les autres ou des dégâts matériels, respectez les instructions ci-dessous. Tout dysfonctionnement dû au non-respect des instructions peut occasionner des nuisances ou des dégâts dont la gravité est classée comme décrit ci-après:

Ce symbole signale la présence d’un

AVERTISSEMENT

ATTENTION

danger pouvant provoquer des blessures graves ou mortelles.

Ce symbole signale la présence d’un danger pouvant provoquer des blessures corporelles ou des dégâts matériels.

Les instructions à respecter sont classées d’après les symboles suivants:

Ce symbole désigne une action INTERDITE.

Ces symboles désignent des

UNITÉ INTÉRIEURE ET UNITÉ EXTÉRIEURE

actions OBLIGATOIRES.

AVERTISSEMENT

Cet appareil n’est pas conçu pour être utilisé par des personnes (y compris les enfants) aux capacités physiques, sensorielles ou mentales diminuées, ou manquant d’expérience ou de connaissances, sauf si une personne responsable de leur sécurité leur a expliqué le fonctionnement de l’appareil et les garde sous surveillance. Les enfants doivent être supervisés aﬁ n qu’ils ne jouent pas avec l’appareil.

Veuillez consulter un revendeur agréé ou un spécialiste pour la réparation, l’installation, le retrait ou le déménagement de l’unité. Une installation et une manipulation incorrectes pourraient occasionner des fuites, un choc électrique ou un incendie.

N’installez pas l’appareil dans une atmosphère potentiellement explosive ou inﬂ ammable. Sinon, il y a un risque d’incendie.

N’insérez jamais vos doigts ou des objets dans l’unité intérieure ou extérieure du climatiseur, les parties tournantes peuvent causer des blessures.

Ne touchez pas l’unité extérieure au cours d’un orage, cela pourrait provoquer un choc électrique.

N’essayez pas de réparer l’appareil vous-même. Vous pourriez vous blesser en cas de mauvaise manipulation.

N’installez pas l’unité intérieure à l’extérieur. Elle est uniquement conçue pour une installation en intérieur.

ATTENTION

UNITÉ INTÉRIEURE ET UNITÉ EXTÉRIEURE

AVERTISSEMENT

ALIMENTATION

N’utilisez pas de cordon modiﬁ é, de raccords, de rallonge ou de cordon non spéciﬁ é aﬁ n d’éviter une surchauffe et un incendie.

Ne partagez pas la même prise d’alimentation qu’un autre équipement aﬁ n d’éviter une surchauffe et un incendie.

N’utilisez pas l’appareil pas avec les mains mouillées aﬁ n d’éviter un choc électrique.

Si le cordon d’alimentation est endommagé, il doit être remplacé par le fabriquant, par un de ses techniciens ou par une personne qui possède des qualiﬁ cations équivalentes aﬁ n d’éviter tout risque.

Cette unité est équipée d’un disjoncteur de courant résiduel (RCCB). Il est fortement conseillé de faire contrôler le fonctionnement du RCCB après l’installation et périodiquement après l’entretien ou la maintenance par un revendeur agréé aﬁ n de garantir son bon fonctionnement. Sinon, il y a risque de choc électrique ou d’incendie en cas de dysfonctionnement.

Il est conseillé de porter des gants pendant la maintenance ou l’entretien aﬁ n d’éviter tout risque.

Cet équipement doit être raccordé à la terre aﬁ n d’éviter un choc électrique ou un incendie.

En cas d’urgence ou dans des conditions anormales (odeur de brulé, etc.), débranchez l’alimentation électrique et contactez le revendeur autorisé.

Prévenez les chocs électriques coupant l’alimentation:

- Avant le nettoyage ou l’entretien.

- En cas de non-utilisation prolongée.

- En cas d’activité orageuse anormalement forte. Cet appareil convient à de multiples usages.

Tous les circuits d’alimentation électrique doivent être coupés avant toute intervention sur les bornes de l’unité intérieure, aﬁ n d’éviter tout choc électrique, brûlure ou blessure mortelle.

ATTENTION

UNITÉ INTÉRIEURE ET UNITÉ EXTÉRIEURE

Ne nettoyez pas l’unité intérieure avec de l’eau, du benzène, du solvant ou de la poudre à récurer.

N’installez pas l’unité à proximité d’un équipement combustible ou dans une salle de bains. Sinon, il y a risque de choc électrique ou d’incendie.

Ne touchez pas le tuyau d’évacuation d’eau de l’unité intérieure pendant le fonctionnement.

Ne posez rien sur ou sous l’unité. Ne vous asseyez pas et ne montez

pas sur l’unité, vous risquez de tomber accidentellement.

Ne touchez pas l’ailette pointue d’aluminium, les parties pointues peuvent causer des dommages.

Assurez-vous que le tuyau de vidange est correctement raccordé. Sinon, une fuite peut se produire.

Vériﬁ ez régulièrement le rack d’installation pour vous assurer qu’il n’est pas endommagé. Après de longues périodes d’utilisation, la solidité du rack d’installation peut être amoindrie.

PANNEAU DE COMMANDE

Ne laissez pas le panneau de commande prendre l’humidité. Sinon, il y a risque de choc électrique ou d’incendie.

N’appuyez pas sur les touches du panneau de commande à l’aide d’objets durs et pointus. Vous pourriez endommager l’unité.

Ne nettoyez pas le panneau de commande avec de l’eau, du benzène, du diluant ou de la poudre à récurer.

N’inspectez pas et n’entretenez pas le panneau de commande vous-même. Consultez un revendeur agréé. Sinon, vous pourriez vous blesser en cas de mauvaise manipulation.

Panneau

FRANÇAIS

Unité Intérieure

Unité Extérieure

Panneau de commande

Alimentation

Réservoir d’eau

Chauffage au sol

+ 25 hidden pages