Panasonic HDC-MDH1GC, HDC-MDH1GK Service Manual
© Panasonic Corporation 2010 Unauthorized copying and distribution is a violation of law.
ORDER NO. VM1009041CE
B27
High Definition Video Camera
Model No. HDC-MDH1GC
HDC-MDH1GK
Vol. 1
Colour
(K)...........Black Type
4
2
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions -----------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.)--------3
2Warning--------------------------------------------------------------4
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------4
2.2. Caution for AC Cord (For GC) --------------------------5
2.3. How to Replace the Lithium Battery-------------------6
3 Service Navigation------------------------------------------------7
3.1. Introduction --------------------------------------------------7
3.2. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------7
3.3. Important Notice 1 -----------------------------------------7
3.4. After replacing the MAIN P.C.B., be sure to
achieve adjustment----------------------------------------7
3.5. How to Define the Model Suffix-------------------------8
3.6. Formatting----------------------------------------------------8
4 Specifications------------------------------------------------------9
5 Location of Controls and Components------------------ 11
6 Service Mode-----------------------------------------------------15
6.1. Lock Search History Indication -----------------------16
6.2. Power ON Self Check Result Display--------------- 16
7 Service Fixture & Tools---------------------------------------17
7.1. When Replacing the Main P.C.B. --------------------17
7.2. Service Position ------------------------------------------17
8 Disassembly and Assembly Instructions--------------- 18
8.1. Disassembly Flow Chart--------------------------------18
8.2. PCB Location----------------------------------------------18
8.3. Disassembly Procedure--------------------------------19
9 Measurements and Adjustments --------------------------35
9.1. Electric Adjustment --------------------------------------35
10 Factory Setting---------------------------------------------------37
10.1. How To Turn On The Factory Settings?------------ 37
10.2. What Is The Factory Settings? -----------------------37
3
1 Safety Precautions
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These part s are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been overheated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading
should be between 1 MΩ and 5.2 MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
1.3. Leakage Current Hot Check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μF
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure. 1
4
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component da mage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as a luminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
5
2.2. Caution for AC Cord
(For GC)
2.2.1. Information for Your Safety
IMPORTANT
Your attention is drawn to the fact that recording of prerecorded tapes or discs or other published or broadcast
material may infringe copyright laws.
WARNING
To reduce the risk of fire or shock hazard, do not e xpose
this equipment to rain or moisture.
CAUTION
To reduce the risk of fire or shock hazard and annoying
interference, use the recommended accessories only.
FOR YOUR SAFETY
DO NOT REMOVE THE OUTER COVER
To prevent electric shock, do not remove the cover. No user
serviceable parts inside. Refer servicing to qualified service
personnel.
2.2.2. Caution for AC Mains Lead
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three-pin mains plug
for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amperes and it is approved
by ASTA or BSI to BS1362
Check for the ASTA mark or the BSI mark on the body of the
fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover, the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
If the fitted moulded plug is unsuitable for the socket outlet in
your home then the fuse should be removed and the plug cut
off and disposed of safety.
There is a danger of severe electrical shock if the cut off plug is
inserted into any 13-ampere socket.
If a new plug is to be fitted please observe the wiring code as
shown below.
If in any doubt, please consult a qualified electrician.
2.2.2.1. Important
The wires in this mains lead are coloured in accordance with
the following code:
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be conn ected to the
terminal in the plug which is marked with the letter L or coloured
RED.
Under no circumstances should either of these wire s be connected to the earth terminal of the three pin plug, marked with
the letter E or the Earth Symbol.
2.2.2.2. Before Use
Remove the Connector Cover as follows.
2.2.2.3. How to Replace the Fuse
1. Remove the Fuse Cover with a screwdriver.
2. Replace the fuse and attach the Fuse cover.
Blue Neutral
Brown Live
6
2.3. How to Replace the Lithium Battery
2.3.1. Replacement Procedure
1. Remove the Side-R Int P.C.B.. (Refer to Disassembly Procedures.)
2. Remove the Lithium battery (Ref. No. “B6701” at foil side of Side-R Int P.C.B.) and then replace it into new one.
NOTE:
This Lithium battery is a critical component.
(Type No.: ML-614S/ZTK Manufactured by Energy Company, Panasonic Corporation)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for HDC-MDH1 series, as well.
7
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2. General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all ele ctrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the
normal solder.
Distinction of P.C.B. Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C
(662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
3.3. Important Notice 1
1. The service manual does not contain the following information, because of the impossibility of servicing at comp onent level
without concerned equipment/facilities.
a. Schematic diagram, Block Diagram and P.C.B. layout of MAIN P.C.B..
b. Parts list for individual parts for MAIN P.C.B..
When a part replacement is required for repairing MAIN P.C.B., replace as an assembled parts. (Main P.C.B.)
2. The following category is /are recycle module part. Please send it/them to Central Repair Center.
• MAIN P.C.B. (VEP03H99A: HDC-MDH1GC/GK)
3.4. After replacing the MAIN P.C.B., be sure to achieve adjustment
The adjustment instruction is available at "software download" on the "Support Information from NWBG/VDBG-AVC" web-site in
"TSN system", together with Maintenance software.
8
3.5. How to Define the Model Suffix
There are two kinds of HDC-MDH1.
• a) HDC-MDH1GK
• b) HDC-MDH1GC
What is the difference is that the “INITIAL SETTING” data which is stored in Flash ROM mounted on Main P.C.B..
3.5.1. Defining methods:
To define the model suffix to be serviced, refer to the rating label which is putted on the Unit.
NOTE:
After replacing the MAIN P.C.B., be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-A VC” web-site in
“TSN system”, together with Maintenance software.
3.6. Formatting
9
4 Specifications
10
11
5 Location of Controls and Components
13 Focus ring
14 Accessory shoe
15 Recording lamp
16 Lens
17 Lens hood
This will reduce the extra light entering the
lens in blight sunlight or backlight etc.,
making it possible to take clearer pictures.
18 Lens hood attachment knob
When you remove the lens hood, first of
all, loosen the lens hood attachment knob.
When you attach the lens hood back, unite
the mark and fasten the lens hood
attachment knob.
If you use the filter kit (optional) or the
conversion lens (optional), remove the
lens hood.
15
16
1817
13 14
1 LCD monitor (Touch screen)
●
It can open up to 90Q.
●
It can rotate up to 180Q towards the lens
or 90Qtowards the opposite direction.
2 Viewfinder
3 Eyecup
4 Sub recording start/stop button
●
This button functions in the same manner
as the recording start/stop button.
5 Sub zoom lever
●
This lever functions in the same manner
as the zoom lever.
6 Speaker
7 Sub menu button [MENU]
●
This button functions in the same manner
as the menu button.
8 Mode switch
9 Intelligent auto/Manual/Manual focus
switch [iA/MANUAL/FOCUS]
10 Cursor button
11 Power LCD button [POWER LCD]
12 Menu button [MENU]
POWER
LCD
MENU
MANUAL
FOCUS
11
910
24
8
12
1
5
7
3 6
Due to limitations in LCD production
technology, there may be some tiny bright
or dark spots on the LCD monitor screen.
However, this is not a malfunction and
does not affect the recorded picture.
Due to limitations in LCD production
technology, there may be some tiny bright
or dark spots on the viewfinder screen.
However, this is not a malfunction and
does not affect the recorded picture.
12
21 Battery holder
22 Battery release button [PUSH]
23 Shoulder strap fixture
24 External microphone terminal
[EXT MIC]
25 Internal microphones
26 Headphone terminal [PHONES]
Excessive sound pressure from
earphones and headphones can cause
hearing loss.
Listening at full volume for long periods
may damage the user’s ears.
27 Photoshot button [ ]
28 Zoom lever [W/T] (In motion picture
recording mode or still picture
recording mode)
Thumbnail display switch [ / ]/
Volume lever [UVOLT] (In playback
mode)
29 Component connector
[COMPONENT]
Use the component cable (only the
supplied cable).
30 Video output connector [VIDEO OUT]
Use the AV cable (only the supplied
cable).
31 Audio output connector
[AUDIO OUT]
Use the AV cable (only the supplied
cable).
2521
26 2827
223242
VIDEO OUT
AUDIOL– –R
OUT
COMPONENT
29 30 31
19 Eyepiece corrector knob
20 Tripod receptacle
20
19
, Flip the belt.
Adjust the length.
, Replace the belt.
DC IN
O
F
F
O
N
34 35
32
33
36
37
38
39
40
32 Access lamp [ACCESS]
33 Card slot
34 HDMI connector [HDMI]
35 USB terminal [ ]
36 DC input terminal [DC IN]
Always use the supplied AC adaptor or a
genuine Panasonic AC adaptor(optional).
37 Status indicator
38 Power switch
39 Recording start/stop button
40 Grip belt
Adjust the length of the grip belt so that it fits
your hand.
13
14
Selecting a mode
Change the mode to recording or playback.
Operate the mode switch to change the mode to , or .
Motion picture recording mode
Still picture recording mode
Playback mode
You can operate by directly touching the LCD monitor (touch screen) with your finger.
It is easier to use the stylus pen (supplied) for detailed operation or if it is hard to operate with
your fingers.
The unit supports both operations using the cursor buttons and operations using the touch
screen. Select the optimal method according to the situation.
In this operating instructions, the majority of functions are described on the basis of
operations using the cursor buttons.
Touch
Touch and release the touch screen to select
icon or picture.
Touch the centre of the icon.
Touching the touch screen will not operate
while you are touching another part of the
touch screen.
Drag
Move your finger while pressing on the touch
screen. Can be used during direct playback.
About the operation icons
To operate the following icons using the cursor buttons, select the desired icon using the
cursor buttons and then press the button in the centre. (Excluding some functions)
///:
These icons are used to switch the menu and
thumbnail display page, for item selection and setting
etc.
:
This icon is used to return to the previous screen such
as when setting menus.
How to use the touch screen
Do not touch the LCD monitor with hard pointed tips, such as ball point pens.
Perform the touch screen calibration when the touch is not recognised or wrong location is
recognised.
15
6 Service Mode
1. Indication method of the service menu
Set the mode switch “Motion Picture Recording” mode.
2. Turn the power on, and then while keep pressing the “Zoom lever” to W side, “Focus” switch and “Menu” button for more than
3 seconds until the top screen of the Service Mode Menu being displayed.
Service mode menu
NOTE:
Do not using service mode except above table of Service Menu.
3. End method of the top screen of the service menu
Push the “Menu” button to end the service mode, and then POWER OFF.
Screen display Contents Function
1 Factory settings Function to throw a product up in a factory shipment state
(When recorded data in Built-in memory, “error display” is done)
4 Lock search history indication Display the camera system error cord for three histories saved
in EEPROM
5 Power ON self check result display Power ON self check (function to diagnose correct function of
the device and interface between devices) result display
16
6.1. Lock Search History Indication
Touch the [ 4 ] of LCD, select Lock search history indication.
Operation specifications
Indication contents
• Lock search history indication
Display the camera system error cord for three histories saved in EEPROM.
• The error cord contents which are displayed
Push the “Menu” button to end the service mode, and then POWER OFF.
6.2. Power ON Self Check Result Display
Touch the [ 5 ] of LCD, select Power ON self check result display.
Operation specifications
Indication contents
• Power ON self check result display
Function to diagnose correct function of the device and interface between devices result display.
Display the following commnucation test result.
- CAM-PWR : Commnucation test between IC2006 to IC301
- CAM-UNI : Commnucation test between IC3401 to IC301
Display other than “OK” are abnomalities of each lines.
Cutting of battery connection or AC power supply connection to end the service mode.
Error code Function
51 Focus control is abnormal
52 Zoom control is abnormal
53 OIS lens control is abnormal
73 High temperature is abnormal
33 Communication between camera to ARM is abnormal
17
7 Service Fixture & Tools
7.1. When Replacing the Main P.C.B.
After replacing the MAIN P.C.B., be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in
“TSN system”, together with Maintenance software.
7.2. Service Position
This Service Position is used for checking and replacing parts. (Extension cable is not use.)
18
8 Disassembly and Assembly Instructions
8.1. Disassembly Flow Chart
This is a disassembling chart.
When assembling, perform this chart conversely.
8.2. PCB Location
19
8.3. Disassembly Procedure
No. Item Fig Removal
1 Face Panel
Shoulder Pad
Fig. D1 8 Screws (A)
Face Panel
Shoulder Pad
2 Hood ND Case Unit
Focus Ring
Fig. D2 1 Screw (B)
Hood ND Case Unit
Focus Ring
3 Side Case-R Unit Fig. D3 3 Screws (C)
4 Screws (D)
4 Screws (E)
3 Screws (F)
FP6006 (Flex)
Side Case-R Unit
4 Speaker Fig. D4 2 Screws (G)
SP Angle
Tape
P6701 (Connector)
Speaker
5 Side-R OP P.C.B. Unit Fig. D5 5 Screws (H)
FP6951 (Flex)
Fig. D6 Sheet
Camera OP Button
2 Slide Buttons
Side-R OP P.C.B. Unit
6 Side-R Int P.C.B. Unit Fig. D7 5 Screws (I)
FP6702 (Flex)
P6701 (Connector)
FP6703 (Flex)
Side-R Int P.C.B. Unit
Fig. D8 NOTE: (When Installing)
7 Lens Unit Fig. D9 3 Screws (J)
FP6108 (Flex)
P6011(Connector)
P6109(Connector)
Fig. D10 3 Screws (K)
Lens Frame-L
Lens Frame-R
Lens Unit
8 Lens Int P.C.B. Unit
Main P.C.B. Unit
Fig. D11 1 Screw (L)
Lens Int P.C.B. Unit
Fig. D12 1 Screw (M)
3 Screws (N)
FP6004 (Flex)
FP6005 (Flex)
FP6007 (Flex)
FP6008 (Flex)
P6001(Connector)
P6003(Connector)
P6009(Connector)
1 Screw (O)
2 Locking tabs
Main Earth Plate
Main P.C.B. Unit
9 SD Holder P.C.B. Unit Fig. D13 FP6004 (Flex)
2 Screws (P)
1 Screw (Q)
1 Locking tab
SD Frame
SD Holder P.C.B. Unit
10 Jack P.C.B. Unit Fig. D14 FP4501 (Flex)
1 Screw (R)
4 Screws (S)
2 Screws (T)
AV Jack Plate
Jack P.C.B. Unit
11 Batt Power P.C.B. Unit
Battery Catcher Unit
Fig. D15 2 Screws (U)
P6751 (Connector)
FP6752 (Flex)
2 Locking tabs
Batt Power P.C.B. Unit
Battery Catcher Unit
12 Handle Mic Unit Fig. D16 4 Screws (V)
FP6008 (Flex)
P6003 (Connector)
P6009 (Connector)
Handle Mic Unit
13 Mic Case Unit
Ext Mic P.C.B. Unit
Fig. D17 2 Screws (W)
Fig. D18 4 Screws (X)
2 Screws (Y)
FP4801(Flex)
Handle Hood Angle (Front)
Mic Case Unit
Ext Mic P.C.B. Unit
14 Handle Zoom P.C.B.
Unit
Fig. D19 1 Screw (Z)
Shoe Spring
4 Screws (a)
Shoe Hold Plate
2 Screws (b)
Fig. D20 2 Locking tabs
Clamper
2 Screws (c)
Handle Zoom P.C.B. Unit
15 EVF Case Unit Fig. D21 2 Screws (d)
Slide Cover
Fig. D22 EVF Case Unit
16 EVF Angle Adj. Case
Unit
Fig. D23 Eye Cap
1 Locking tab
EVF Angle Adj. Case Unit
17 EVF Unit
EVF Int P.C.B. Unit
Fig. D24 2 Screws (e)
Hold Piece
EVF Ring
EVF Lock Ring
4 Screws (f)
2 Rubbers
Fig. D25 7 Locking tabs
EVF Top Case
3 Screws (g)
FP822 (Flex)
EVF Unit
EVF Int P.C.B. Unit
18 Grip Cover Unit Fig. D26 4 Screws (h)
FP6005 (Flex)
Grip Cover Unit
19 Zoom photo P.C.B.
Unit
Fig. D27 3 Screws (i)
FP6602 (Flex)
P6691(Connector)
Fig. D28 1 Screw (j)
Photo Button
Zoom SW Hold Frame
2 Screws (k)
Zoom SW
Zoom Lever Cussion-B
Zoom Photo P.C.B. Unit
20 SS GYRO P.C.B. Unit Fig. D29 3 Screws (l)
Fig. D30 P.C.B. Holder Unit
3 Screws (m)
SS GYRO P.C.B. Unit
No. Item Fig Removal
20
8.3.1. Removal of the Face Panel and
Shoulder Pad
Fig. D1
21 Front P.C.B. Unit Fig. D31 2 Screws (n)
FP6801(Connector)
Remote Controller Window
Fig. D32 2 Screws (o)
P.C.B. Angle
Front P.C.B. Unit
22 LCD Case Unit Fig. D33 3 Screws (p)
Fig. D34 2 Screws (q)
6 Locking tabs
LCD Case Top Unit
FP901 (Flex)
LCD Case Unit
23 LCD Unit
Monitor P.C.B. Unit
Fig. D35 1 Screw (r)
LCD Frame
FP903 (Flex)
FP904 (Flex)
FP905 (Flex)
LCD Unit
Fig. D36 1 Locking tab
Reflection Sheet
Light Guide Plate
Diffusion Sheet
Prism Sheet B
Prism Sheet A
Lighting Plate Holder
Monitor P.C.B. Unit
24 MOS Unit
IR Filter
Fig. D37 2 Screws (s)
MOS Cushion
MOS Unit
IR Filter
25 Focus Motor Fig. D38 3 Screws (t)
4 Solders
2 Convexes
Focus Motor
26 Zoom Motor Fig. D39 3 Screws (u)
4 Solders
2 Convexes
Zoom Motor
No. Item Fig Removal
21
8.3.2. Removal of the Hood ND Case Unit
and Focus Ring
Fig. D2
8.3.3. Removal of the Side Case-R Unit
Fig. D3
22
8.3.4. Removal of the Speaker
Fig. D4
8.3.5. Removal of the Side-R OP P.C.B.
Unit
Fig. D5
Fig. D6
23
8.3.6. Removal of the Side-R Int P.C.B.
Unit
Fig. D7
Fig. D8
8.3.7. Removal of the Lens Unit
Fig. D9
24
Fig. D10
8.3.8. Removal of the Len s Int P.C.B. Unit
and Main P.C.B. Unit
Fig. D11
Fig. D12
25
8.3.9. Removal of the SD Holder P.C.B.
Unit
Fig. D13
8.3.10. Removal of the Jack P.C.B. Unit
Fig. D14
26
8.3.11. Removal of the Batt Power P.C.B.
Unit and Battery Catcher Unit
Fig. D15
8.3.12. Removal of the Handle Mic Unit
Fig. D16
8.3.13. Removal of the Mic Case Unit and
Ext Mic P.C.B. Unit
Fig. D17
27
Fig. D18
8.3.14. Removal of the Handle Zoom P.C.B.
Unit
Fig. D19
Fig. D20
28
8.3.15. Removal of the EVF Case Unit
Fig. D21
Fig. D22
8.3.16. Removal of the EVF Angle Adj.
Case Unit
Fig. D23
29
8.3.17. Removal of the EVF Unit and EVF
Int P.C.B. Unit
Fig. D24
Fig. D25
30
8.3.18. Removal of the Grip Cover Unit
Fig. D26
8.3.19. Removal of the Zoom Photo P.C.B.
Unit
Fig. D27
Fig. D28
8.3.20. Removal of the SS GYRO P.C.B.
Unit
Fig. D29
Loading...