Panasonic CS-C7MKP-7, CS-C9MKP-7, CS-C12MKP-7, CS-C18MKP-7, CS-C24MKP-7 Service Manual

...

Order No: PHAAM1106129C3

Indoor Unit Outdoor Unit CS-C7MKP-7 CS-C9MKP-7

CS-C12MKP-7 CS-C18MKP-7 CS-C24MKP-7

CU-C7MKP-7

CU-C9MKP-7 CU-C12MKP-7 CU-C18MKP-7 CU-C24MKP-7

This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the products dealt with in this service information by anyone else could result in serious injury or death.

WARNING

TABLE OF CONTENTS

1. Safety Precautions .............................................3

2. Specification .......................................................5

3. Features.............................................................11

4. Location of Controls and Components..........12

4.1 Indoor Unit ..................................................12

4.2 Outdoor Unit ...............................................12

4.3 Remote Control ..........................................12

5. Dimensions .......................................................13

5.1 Indoor Unit ..................................................13

5.2 Outdoor Unit ...............................................15

6. Refrigeration Cycle Diagram ...........................17

7. Block Diagram ..................................................18

8. Wiring Connection Diagram ............................20

8.1 CS-C7MKP-7 CU-C7MKP-7

CS-C9MKP-7 CU-C9MKP-7

CS-C12MKP-7 CU-C12MKP-7 ...................20

8.2 CS-C18MKP-7 CU-C18MKP-7..................21

8.3 CS-C24MKP-7 CU-C24MKP-7..................22

9. Electronic Circuit Diagram ..............................23

9.1 CS-C7MKP-7 CU-C7MKP-7

CS-C9MKP-7 CU-C9MKP-7

CS-C12MKP-7 CU-C12MKP-7 ...................23

9.2 CS-C18MKP-7 CU-C18MKP-7..................24

9.3 CS-C24MKP-7 CU-C24MKP-7..................25

13.2 7 Minutes Time Save Control .................... 62

13.3 60 Seconds Forced Operation .................. 62

13.4 Starting Current Control ............................ 62

13.5 Freeze Prevention Control ........................ 63

13.6 Compressor Reverse Rotation Protection

Control ....................................................... 63

13.7 Dew Prevention Control ............................ 64

14. Servicing Mode ................................................ 65

14.1 Auto OFF/ON Button ................................. 65

14.2 Remote Control Button.............................. 66

15. Troubleshooting Guide ................................... 67

15.1 Refrigeration cycle system ........................ 67

16. Disassembly and Assembly Instructions ..... 69

16.1 CS-C7MKP-7 CS-C9MKP-7

CS-C12MKP-7........................................... 69

16.2 CS-C18MKP-7 CS-C24MKP-7................. 73

17. Technical Data ................................................. 77

17.1 Thermostat Characteristics ....................... 77

17.2 Operation Characteristics.......................... 78

18. Exploded View and Replacement Parts

List .................................................................... 88

18.1 Indoor Unit ................................................. 88

18.2 Outdoor Unit .............................................. 94

10. Printed Circuit Board .......................................26

10.1 Indoor Unit ..................................................26

11. Installation Instruction.....................................30

11.1 Select the Best Location.............................30

11.2 Indoor Unit ..................................................31

11.3 Outdoor Unit ...............................................35

12. Operation Control.............................................38

12.1 Cooling Operation.......................................38

12.2 Soft Dry Operation......................................40

12.3 Automatic Operation...................................42

12.4 Indoor Fan Speed Control ..........................43

12.5 Outdoor Fan Speed Control .......................45

12.6 Vertical Airflow Direction Control................45

12.7 Horizontal Airflow Direction Control............47

12.8 Powerful Operation.....................................48

12.9 Quiet Operation ..........................................48

12.10 Timer Control ..............................................49

12.11 Random Auto Restart Control ....................49

12.12 Remote Control Signal Receiving

Sound .........................................................49

12.13 Patrol Operation .........................................50

12.14 E-ion operation ...........................................54

12.15 AUTO COMFORT and ECO NAVI

Operation....................................................57

13. Protection Control ............................................62

13.1 Restart Control (Time Delay Safety

Control).......................................................62

1. Safety Precautions

 Read the following “SAFETY PRECAUTIONS” carefully before perform any servicing.  Electrical work must be installed or serviced by a licensed electrician. Be sure to use the correct rating of the

power plug and main circuit for the model installed.

 The caution items stated here must be followed because these important contents are related to safety. The

meaning of each indication used is as below. Incorrect installation or servicing due to ignoring of the instruction will cause harm or damage, and the seriousness is classified by the following indications.

WARNING

CAUTION

 The items to be followed are classified by the symbols:

This symbol denotes item that is PROHIBITED from doing.

 Carry out test running to confirm that no abnormality occurs after the servicing. Then, explain to user the

operation, care and maintenance as stated in instructions. Please remind the customer to keep the operating instructions for future reference.

1. Do not modify the machine, part, material during repairing service.

This indication shows the possibility of causing death or serious injury.

This indication shows the possibility of causing injury or damage to properties.

WARNING

2. If wiring unit is supplied as repairing part, do not repair or connect the wire even only partial wire break. Exchange the whole wiring unit.

3. Do not wrench the fasten terminal. Pull it out or insert it straightly.

4. Engage dealer or specialist for installation and servicing. If installation of servicing done by the user is defective, it will cause water leakage, electrical shock or fire.

5. Install according to this installation instructions strictly. If installation is defective, it will cause water leakage, electric shock or fire.

6. Use the attached accessories parts and specified parts for installation and servicing. Otherwise, it will cause the set to fall, water leakage, fire or electrical shock.

7. Install at a strong and firm location which is able to withstand the set’s weight. If the strength is not enough or installation is not properly done, the set will drop and cause injury.

8. For electrical work, follow the local national wiring standard, regulation and the installation instruction. An independent circuit and single outlet must be used. If electrical circuit capacity is not enough or defect found in electrical work, it will cause electrical shock or fire.

9. This equipment is strongly recommended to install with Earth Leakage Circuit Breaker (ELCB) or Residual Current Device (RCD). Otherwise, it may cause electrical shock and fire in case equipment breakdown or insulation breakdown.

10. Do not use joint cable for indoor / outdoor connection cable. Use the specified Indoor/Outdoor connection cable, refer to installation instruction CONNECT THE CABLE TO THE INDOOR UNIT and connect tightly for indoor / outdoor connection. Clamp the cable so that no external force will be acted on the terminal. If connecting or fixing is not perfect, it will cause heat up or fire at the connection.

11. Wire routing must be properly arranged so that control board cover is fixed properly. If control board cover is not fixed perfectly, it will cause heat-up or fire at the connection point of terminal, fire or electrical shock.

12. When install or relocate air conditioner, do not let any substance other than the specified refrigerant, eg. air etc. mix into refrigeration cycle (piping). (Mixing of air etc. will cause abnormal high pressure in refrigeration cycle and result in explosion, injury etc.).

13. Do not install outdoor unit near handrail of veranda. When installing air-conditioner unit at veranda of high rise building, child may climb up to outdoor unit and cross over the handrail and causing accident.

14. This equipment must be properly earthed. Earth line must not be connected to gas pipe, water pipe, earth of lightning rod and telephone. Otherwise, it may cause electric shock in case equipment breakdown or insulation breakdown.

15. Keep away from small children, the thin film may cling to nose and mouth and prevent breathing.

16. Do not use unspecified cord, modified cord, joint cord or extension cord for power supply cord. Do not share the single outlet with other electrical appliances. Poor contact, poor insulation or over current will cause electrical shock or fire.

17. Tighten the flare nut with torque wrench according to specified method. If the flare nut is over-tightened, after a long period, the flare may break and cause refrigerant gas leakage.

18. During pump down operation, stop the compressor before remove the refrigeration piping. (Removal of compressor while compressor is operating and valves are opened will cause suck-in of air, abnormal high pressure in refrigeration cycle and result in explosion, injury etc.)

19. During installation, install the refrigerant piping properly before run the compressor. (Operation of compressor without fixing refrigeration piping and valves at opened condition will caused suck-in of air, abnormal high pressure in refrigeration cycle and result in explosion, injury etc).

20. After completion of installation or service, confirm there is no leakage or refrigerant gas. It may generate toxic gas when the refrigerant contacts with fire.

21. Ventilate if there is refrigerant gas leakage during operation. It may cause toxic gas when refrigerant contacts with fire.

22. Do not insert your fingers or other objects into the unit, high speed rotating fan may cause injury.

23. Must not use other parts except original parts described in catalog and manual.

WARNING

CAUTION

1. Do not install the unit at place where leakage of flammable gas may occur. In case gas leaks and accumulates at surrounding of the unit, it may cause fire.

2. Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water may enter the room and damage the furniture.

3. Tighten the flare nut with torque wrench according to specified method. If the flare nut is over-tightened, after a long period, the flare may break and cause refrigerant gas leakage.

4. Do not touch outdoor unit air inlet and aluminium fin. It may cause injury.

5. Select an installation location which is easy for maintenance.

6. Pb free solder has a higher melting point than standard solder; typically the melting point is 50°F – 70°F (30°C – 40°C) higher. Please use a high temperature solder iron. In case of the soldering iron with temperature control, please set it to 700 ± 20°F (370 ± 10°C). Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).

7. Power supply connection to the air conditioner. Connect the power supply cord of the air conditioner to the mains using one of the following methods. Power supply point shall be the place where there is ease for access for the power disconnection in case of emergency. In some countries, permanent connection of this room air conditioner to the power supply is prohibited. i. Power supply connection to the receptacle using a power plug. Use an approved 15/16A (3/4~1.5HP) or 16A (2.0HP) or 20A (2.5HP) or 25A (3.0HP) power plug with earth pin for the connection to the socket. ii. Power supply connection to a circuit breaker for the permanent component. Use an approved 16A (3/4~2.0HP) or 20A (2.5HP) or 25A (3.0HP) circuit breaker for the permanent connection. It must be a double pole switch with a minimum 3.0 mm contact gap.

8. Do not release refrigerant during piping work for installation, servicing, reinstallation and during repairing a refrigerant parts. Take care of the liquid refrigerant, it may cause frostbite.

9. Installation or servicing work: It may need two people to carry out the installation or servicing work.

10. Do not install this appliance in a laundry room or other location where water may drip from the ceiling, etc.

11. Do not sit or step on the unit, you may fall down accidentally.

12. Do not touch the sharp aluminium fins or edges of metal parts. If you are required to handle sharp parts during installation or servicing, please wear hand glove. Sharp parts may cause injury.

2. Specification

Model

Performance Test Condition NEW JIS NEW JIS

Power Supply

Capacity

Running Current A 3.0 3.0 3.8 3.7

Input Power W 590 640 800 835

EER

Cooling

Power Factor % 89 89 96 94

Indoor Noise (H / L)

Outdoor Noise (H / L)

Max Current (A) / Max Input Power (W) 3.9 / 860 4.8 / 1.09k

Starting Current (A) 12.2 17.0

Type Hermetic Motor Hermetic Motor

Compressor

Indoor Fan

Speed

Outdoor Fan

Speed Hi rpm 810 - 840 810 - 840

Moisture Removal L/h (Pt/h) 1.3 (2.7) 1.6 (3.4)

Indoor Airflow

Outdoor

Airflow

Refrigeration

Cycle

Motor Type Induction (2 poles) Induction (2 poles)

Output Power W 550 700

Type Cross-Flow Fan Cross-Flow Fan

Material ASG20K1 ASG20K1

Motor Type Induction (4 poles) Induction (4 poles)

Input Power W 38.0 - 42.0 38.0 - 42.0

Output Power W 22 22

QLo rpm 690 - 690 690 - 690

Lo rpm 760 - 760 760 - 760

Me rpm 860 - 860 950 - 950

Hi rpm 960 - 960 1150 - 1150

SHi rpm 1050 - 1050 1170 - 1170

Type Propeller Fan Propeller Fan

Material PP Resin PP Resin

Motor Type Induction (6 poles) Induction (6 poles)

Input Power W 66.0 - 75.0 66.0 - 75.0

Output Power W 30 30

QLo m3/min (ft3/min) 5.7 (201) - 5.7 (201) 5.9 (208) - 5.9 (208)

Lo m3/min (ft3/min) 6.1 (215) - 6.1 (215) 6.3 (223) - 6.3 (223)

Me m3/min (ft3/min) 6.9 (244) - 6.9 (244) 7.9 (280) - 7.9 (280)

Hi m3/min (ft3/min) 7.9 (279) - 7.9 (279) 9.8 (346) - 9.8 (346)

SHi m

Hi m

Control Device Capillary Tube Capillary Tube

Refrigerant Oil cm3 ATMOS M60 or Suniso 4GDID (290) ATMOS M60 or Suniso 4GDID (350)

Refrigerant Type g (oz) R22, 400 (14.1) R22, 470 (16.6)

Indoor CS-C7MKP-7 CS-C9MKP-7

Outdoor CU-C7MKP-7 CU-C9MKP-7

Phase, Hz Single, 50 Single, 50

V 220 240 220 240

kW 2.00 2.05 2.65 2.70

BTU/h 6820 6990 9040 9210

kJ/h 7200 7380 9540 9720

W/W 3.39 3.20 3.31 3.23

Btu/hW 11.6 10.9 11.3 11.0

dB-A 33 / 26 33 / 26 36 / 26 36 / 26

Power Level dB 46 / - 46 / - 49 / - 49 / -

dB-A 46 / - 47 / - 46 / - 47 / -

Power Level dB 61 / - 62 / - 61 / - 62 / -

/min (ft3/min) 8.6 (305) - 8.6 (305) 10.0 (352) - 10.0 (352)

/min (ft3/min) 28.8 (1020) - 29.6 (1040) 28.8 (1020) - 29.6 (1040)

Height(I/D / O/D) mm (inch) 290 (11-7/16) 510 (20-3/32) 290 (11-7/16) 510 (20-3/32)

Dimension

Weight Net (I/D / O/D) kg (lb) 9 (20) 22 (49) 9 (20) 21 (46)

Pipe Diameter (Liquid / Gas) mm (inch) 6.35 (1/4) / 9.52 (3/8) 6.35 (1/4) / 9.52 (3/8)

Length range (min – max) m (ft) 3 (9.8) ~ 10 (32.8) 3 (9.8) ~ 10 (32.8)

I/D & O/D Height different m (ft) 5 (16.4) 5 (16.4)

Piping

Additional Gas Amount g/m (oz/ft) 10 (0.1) 10 (0.1)

Length for Additional Gas m (ft) 7.5 (24.6) 7.5 (24.6)

Drain Hose

Indoor Heat

Exchanger

Outdoor

Heat

Exchanger

Air Filter

Power Supply Cord A 10 10

Indoor Operation Range

Outdoor Operation Range

Width (I/D / O/D) mm (inch) 870 (34-9/32) 650 (25-19/32) 870 (34-9/32) 650 (25-19/32)

Depth (I/D / O/D) mm (inch) 204 (8-1/16) 230 (9-1/16) 204 (8-1/16) 230 (9-1/16)

Standard length m (ft) 7.5 (24.6) 7.5 (24.6)

Inner Diameter mm 16.2 16.2

Length mm 550 550

Fin Material Aluminium (Pre coated) Aluminium (Pre coated)

Fin Type Slit Fin Slit Fin

Row x Stage x FPI 2 x 10 x 17 2 x 10 x 17

Size (W x H x L) mm 610 x 210 x 25.4 610 x 210 x 25.4

Fin Material Aluminium (Blue coated) Aluminium (Blue coated)

Fin Type Slit Fin Slit Fin

Row x Stage x FPI 1 x 23 x 17 1 x 23 x 17

Size (W x H x L) mm 12.7 x 483 x 578.4 12.7 x 483 x 578.4

Material Polypropelene Polypropelene

Type One-touch One-touch

Power Supply Indoor Indoor

Thermostat - -

Protection Device 2-Stage Overload Protector 2-Stage Overload Protector

DRY BULB WET BULB DRY BULB WET BULB

Maximum 32 23 32 23

Minimum 16 11 16 11

Maximum 43 26 43 26

Minimum 16 11 16 11

1. Cooling capacities are based on indoor temperature of 27°C Dry Bulb (80.6°F Dry Bulb), 19.0°C Wet Bulb (66.2°F Wet Bulb) and outdoor air temperature of 35°C Dry Bulb (95°F Dry Bulb), 24°C Wet Bulb (75.2°F Wet Bulb)

Specifications are subjected to change without prior notice for further improvement.

Model

Indoor CS-C12MKP-7

Outdoor CU-C12MKP-7

Performance Test Condition NEW JIS

Power Supply

Phase, Hz Single, 50

V 220 240

kW 3.52 3.57

Capacity

BTU/h 12000 12200

kJ/h 12670 12850

Running Current A 5.3 5.2

Input Power W 1.11k 1.15k

EER

Cooling

W/W 3.17 3.10

Btu/hW 10.8 10.6

Power Factor % 95 92

Indoor Noise (H / L / QLo)

Outdoor Noise (H / L)

dB-A 39 / 29 39 / 29

Power Level dB 52 / - 52 / -

dB-A 48 / - 49 / -

Power Level dB 63 / - 64 / -

Max Current (A) / Max Input Power (W) 6.8 / 1.54k

Starting Current (A) 22.0

Type Hermetic Motor

Compressor

Motor Type Induction (2 poles)

Output Power W 950

Type Cross-Flow Fan

Material ASG20K1

Motor Type Induction (4 poles)

Input Power W 47.0 - 50.0

Output Power W 24

QLo rpm 730 - 730

Indoor Fan

Speed

Lo rpm 810 - 810

Me rpm 940 - 940

Hi rpm 1120 - 1120

SHi rpm 1150 - 1150

Type Propeller Fan

Material PP Resin

Motor Type Induction (6 poles)

Input Power W 66.6 - 74.6

Outdoor Fan

Output Power W 30

Speed Hi rpm 830 - 860

Moisture Removal L/h (Pt/h) 2.1 (4.4)

QLo m3/min (ft3/min) 7.2 (253) - 7.2 (253)

Lo m3/min (ft3/min) 7.9 (277) - 7.9 (277)

Indoor Airflow

Me m3/min (ft3/min) 9.2 (326) - 9.2 (326)

Hi m3/min (ft3/min) 10.8 (381) - 10.8 (381)

/min (ft3/min) 11.3 (399) - 11.3 (399)

/min (ft3/min) 22.0 (780) - 23.6 (830)

Outdoor

Airflow

SHi m

Hi m

Control Device Capillary Tube

Refrigeration

Cycle

Refrigerant Oil cm3 ATMOS M60 or Suniso 4GDID (350)

Refrigerant Type g (oz) R22, 770 (27.2)

Height(I/D / O/D) mm (inch) 290 (11-7/16) 510 (20-3/32)

Dimension

Weight Net (I/D / O/D) kg (lb) 9 (20) 25 (55)

Pipe Diameter (Liquid / Gas) mm (inch) 6.35 (1/4) / 12.70 (1/2)

Length range (min – max) m (ft) 3 (9.8 ) ~ 15 (49.2)

I/D & O/D Height different m (ft) 5 (16.4)

Piping

Additional Gas Amount g/m (oz/ft) 10 (0.1)

Length for Additional Gas m (ft) 7.5 (24.6)

Drain Hose

Indoor Heat

Exchanger

Outdoor

Heat

Exchanger

Air Filter

Power Supply Cord A 10

Indoor Operation Range

Outdoor Operation Range

Width (I/D / O/D) mm (inch) 870 (34-9/32) 650 (25-19/32)

Depth (I/D / O/D) mm (inch) 204 (8-1/16) 230 (9-1/16)

Standard length m (ft) 7.5 (24.6)

Inner Diameter mm 16.2

Length mm 550

Fin Material Aluminium (Pre coated)

Fin Type Slit fin

Row x Stage x FPI 2 x 15 x 17

Size (W x H x L) mm 610 x 315 x 25.4

Fin Material Aluminium (Blue Coated)

Fin Type Slit Fin

Row x Stage x FPI 2 x 23 x 17

Size (W x H x L) mm 25.4 x 483 x 582:562

Material Polypropelene

Type One-touch

Power Supply Indoor

Thermostat -

Protection Device 2-Stage Overload Protector

DRY BULB WET BULB

Maximum 32 23

Minimum 16 11

Maximum 43 26

Minimum 16 11

Specifications are subjected to change without prior notice for further improvement.

Model

Indoor CS-C18MKP-7 CS-C24MKP-7

Outdoor CU-C18MKP-7 CU-C24MKP-7

Performance Test Condition NEW JIS NEW JIS

Power Supply

Phase, Hz Single, 50 Single, 50

V 220 240 220 240

kW 5.40 5.40 7.03 7.03

Capacity

BTU/h 18400 18400 24000 24000

kJ/h 19440 19440 25310 25310

Running Current A 8.4 8.3 11.0 11.1

Input Power W 1.75k 1.85k 2.35k 2.47k

EER

Cooling

W/W 3.09 2.92 2.99 2.85

Btu/hW 10.51 9.95 10.21 9.72

Power Factor % 95 93. 97 93

Indoor Noise (H / L)

Outdoor Noise (H / L)

dB-A 43 / 37 43 / 37 46 / 40 46 / 40

Power Level dB - - - -

dB-A 53 / - 54 / - 54 / - 55 / -

Power Level dB - - - -

Max Current (A) / Max Input Power (W) 10.7 / 2.41k 14.2 / 3.06k

Starting Current (A) 40.0 60.0

Type Hermetic Motor Hermetic Motor

Compressor

Motor Type Induction (2 poles) Induction (2 poles)

Output Power W 1.5k 2.0k

Type Cross-Flow Fan Cross-Flow Fan

Material ASG30K1 ASG30K1

Motor Type Transistor (8 poles) Transistor (8 poles)

Input Power W 94.8 - 94.8 94.8 - 94.8

Output Power W 40 40

QLo rpm 920 - 920 1020 - 1020

Indoor Fan

Speed

Lo rpm 1010 - 1010 1110 - 1110

Me rpm 1120 - 1120 1230 - 1230

Hi rpm 1240 - 1240 1350 - 1350

SHi rpm 1390 - 1390 1500 - 1500

Type Propeller Fan Propeller Fan

Material PP Resin PP Resin

Motor Type Induction (6 poles) Induction (6 poles)

Input Power W 76.2 - 86.5 134.4 - 152.0

Outdoor Fan

Output Power W 36 66

Speed

Lo rpm - 420 - 480

Hi rpm 830 - 855 740 - 770

Moisture Removal L/h (Pt/h) 2.9 (6.1) 4.0 (8.5)

QLo m3/min (ft3/min) 12.2 (430) - 12.2 (430) 13.8 (486) - 13.8 (486)

Lo m3/min (ft3/min) 13.4 (472) - 13.4 (472) 15.0 (528) - 15.0 (528)

Indoor Airflow

Me m3/min (ft3/min) 14.8 (523) - 14.8 (523) 16.6 (586) - 16.6 (586)

Hi m3/min (ft3/min) 16.4 (579) - 16.4 (579) 18.2 (642) - 18.2 (642)

/min (ft3/min) 18.4 (649) - 18.4 (649) 20.2 (714) - 20.2 (714)

/min (ft3/min) 30.3 (1070) - 31.3 (1100) 45.5 (1610) - 47.5 (1680)

Outdoor

Airflow

SHi m

Lo m3/min (ft3/min) - 24.8 (880) - 28.5 (1010)

Hi m

Refrigeration

Cycle

Dimension

Weight Net (I/D / O/D) kg (lb) 12 (26) 37 (82) 12 (26) 53 (117)

Pipe Diameter (Liquid / Gas) mm (inch) 6.35 (1/4) / 12.70 (1/2) 6.35 (1/4) / 15.88 (5/8)

Length range (min – max) m (ft) 3 (9.8) ~ 25 (82.0) 3 (9.8) ~ 25 (82.0)

I/D & O/D Height different m (ft) 20 (65.6) 20 (65.6)

Piping

Additional Gas Amount g/m (oz/ft) 20 (0.2) 30 (0.3)

Length for Additional Gas m (ft) 7.5 (24.6) 7.5 (24.6)

Drain Hose

Indoor Heat

Exchanger

Outdoor

Heat

Exchanger

Air Filter

Power Supply Cord A 16 20

Protection Device Overload Protector -

Indoor Operation Range

Outdoor Operation Range

Control Device Capillary Tube Capillary Tube

Refrigerant Oil cm3 ATMOS M60 or Suniso 4GDID (450) ATMOS M60 or Suniso 4GDID (700)

Refrigerant Type g (oz) R22, 950 (33.5) R22, 1.20k (42.4)

Height(I/D / O/D) mm (inch) 290 (11-7/16) 540 (21-9/32) 290 (11-7/16) 750 (29-17/32)

Width (I/D / O/D) mm (inch) 1070 (42-5/32) 780 (30-23/32) 1070 (42-5/32) 875 (34-15/32)

Depth (I/D / O/D) mm (inch) 235 (9-9/32) 289 (11-13/32) 235 (9-9/32) 345 (13-19/32)

Standard length m (ft) 5.0 (16.4) 5.0 (16.4)

Inner Diameter mm 16 16

Length mm 550 550

Fin Material Aluminium (Pre coated) Aluminium (Pre coated)

Fin Type Slit Fin Slit Fin

Row x Stage x FPI 2 x 15 x 21 2 x 15 x 21

Size (W x H x L) mm 810 x 315 x 25.4 810 x 315 x 25.4

Fin Material Aluminium (Blue coated) Aluminium (Blue coated)

Fin Type Slit Fin Slit Fin

Row x Stage x FPI 2 x 24 x 17 2 x 34 x 17

Size (W x H x L) mm 25.4 x 504 x 693.4:713.4 25.4 x 714 x 831.2:811.2

Material Polypropelene Polypropelene

Type One-touch One-touch

Power Supply Indoor Indoor

Thermostat - Mechanical

DRY BULB WET BULB DRY BULB WET BULB

Maximum 32 23 32 23

Minimum 16 11 16 11

Maximum 43 26 43 26

Minimum 16 11 16 11

Specifications are subjected to change without prior notice for further improvement.

3. Features

 E-ion Air Purifying System with Patrol Sensor

o Active e-ions are released to catch dust particles and bring them back the large positively charged filter. o Patrol Sensor color changes to indicate the dirt level in the air

 Long Installation Piping

o CS/CU-C7MK, CS/CU-C9MK, long piping up to 10 meters. o CS/CU-C12MK, long piping up to 15 meters. o CS/CU-C18MK, CS/CU-C24MK, long piping up to 25 meters.

 Easy to use remote control

 Quality Improvement

o Random auto restart after power failure for safety restart operation o Gas leakage protection o Prevent compressor reverse cycle o Inner protector to protect compressor o Noise prevention during soft dry operation o Blue coated condenser for high resistance to corrosion

 Operation Improvement

o Quiet mode to reduce the indoor unit operating sound o Powerful mode to reach the desired room temperature quickly o 24-hour timer setting

4. Location of Controls and Components

4.1 Indoor Unit

4.2 Outdoor Unit

4.3 Remote Control

5. Dimensions

5.1 Indoor Unit

5.1.1 CS-C7MKP-7 CS-C9MKP-7 CS-C12MKP-7

5.1.2 CS-C18MKP-7 CS-C24MKP-7

5.2 Outdoor Unit

5.2.1 CU-C7MKP-7 CU-C9MKP-7 CU-C12MKP-7

5.2.2 CU-C18MKP-7

5.2.3 CU-C24MKP-7

6. Refrigeration Cycle Diagram

7. Block Diagram

7.1.1 CS-C7MKP-7 CU-C7MKP-7 CS-C9MKP-7 CU-C9MKP-7

CS-C12MKP-7 CU-C12MKP-7

7.1.2 CS-C18MKP-7 CU-C18MKP-7 CS-C24MKP-7 CU-C24MKP-7

8. Wiring Connection Diagram

8.1 CS-C7MKP-7 CU-C7MKP-7 CS-C9MKP-7 CU-C9MKP-7

CS-C12MKP-7 CU-C12MKP-7

Resistance of Indoor Fan Motor Windings

MODEL CS-C7MKP-7 / CS-C9MKP-7 / CS-C12MKP-7

CONNECTION CWA921434

BLUE-YELLOW 351.3

YELLOW-RED 343.9

Note: Resistance at 25°C of ambient temperature.

Resistance of Outdoor Fan Motor Windings Resistance of Outdoor Fan Motor Windings

MODEL CU-C9MKP-7 CU-C12MKP-7 MODEL CU-C7MKP-7

CONNECTION CWA951691 CWA951691 CONNECTION CWA951673

BLUE-YELLOW 388 388 BLUE-YELLOW 318

YELLOW-RED 305 305 YELLOW-RED 272

Note: Resistance at 20°C of ambient temperature.

Resistance of Compressor Windings Resistance of Compressor Windings

MODEL CU-C9MKP-7 CU-C12MKP-7 MODEL CU-C7MKP-7

CONNECTION 2PS146D3BA06 2PS206D3CA06 CONNECTION 2RS122D5AD02

C-R 5.091 2.878 C-R 5.627

C-S 5.382 5.874 C-S 12.19

Note: Resistance at 20°C of ambient temperature.

8.2 CS-C18MKP-7 CU-C18MKP-7

Resistance of Outdoor Fan Motor Windings

MODEL CU-C18MKP-7 MODEL CU-C18MKP-7

CONNECTION CWA951705 CONNECTION 2KS314D5BA06

BLUE-YELLOW 223.0 C-R 1.853

YELLOW-RED 255.6 C-S 4.879

Note: Resistance at 25°C of ambient temperature. Note: Resistance at 20°C of ambient temperature.

Resistance of Compressor Windings

8.3 CS-C24MKP-7 CU-C24MKP-7

Resistance of Outdoor Fan Motor Windings

MODEL CU-C24MKP-7 MODEL CU-C24MKP-7

CONNECTION CWA951383J CONNECTION 2JS438D3CB04

BLUE-YELLOW 116 C-R 1.121

YELLOW-ORANGE 136 C-S 2.535

YELLOW-RED 103 Note: Resistance at 20°C of ambient temperature.

Note: Resistance at 25°C of ambient temperature.

Resistance of Compressor Windings

9. Electronic Circuit Diagram

9.1 CS-C7MKP-7 CU-C7MKP-7 CS-C9MKP-7 CU-C9MKP-7 CS-C12MKP-7 CU-C12MKP-7

9.2 CS-C18MKP-7 CU-C18MKP-7

9.3 CS-C24MKP-7 CU-C24MKP-7

10. Printed Circuit Board

10.1 Indoor Unit

10.1.1 Main Printed Circuit Board

10.1.1.1 CS-C7MKP-7 CS-C9MKP-7 CS-C12MKP-7

10.1.1.2 CS-C18MKP-7 CS-C24MKP-7

10.1.2 Indicator Printed Circuit Board

10.1.3 Receiver Printed Circuit Board

10.1.4 High Voltage Power Supply Printed Circuit Board

10.1.5 Comparator Printed Circuit Board

10.1.6 Human Activity Sensor Printed Circuit Board

11. Installation Instruction

11.1 Select the Best Location

11.1.1 Indoor Unit

 Do not install the unit in excessive oil fume area

such as kitchen, workshop and etc.

 There should not be any heat source or steam

near the unit.

 There should not be any obstacles blocking the air

circulation.

 A place where air circulation in the room is good.  A place where drainage can be easily done.  A place where noise prevention is taken into

consideration.

 Do not install the unit near the door way.  Ensure the spaces indicated by arrows from the

wall, ceiling, fence or other obstacles.

 Recommended installation height for indoor unit

shall be at least 2.5 m.

11.1.2 Outdoor Unit

 If an awning is built over the unit to prevent direct

sunlight or rain, be careful that heat radiation from the condenser is not obstructed.

 There should not be any animal or plant which

could be affected by hot air discharged.

 Keep the spaces indicated by arrows from wall,

ceiling, fence or other obstacles.

 Do not place any obstacles which may cause a

short circuit of the discharged air.

 If piping length is over the [piping length for

additional gas], additional refrigerant should be added as shown in the table.

11.1.3 Indoor/Outdoor Unit Installation Diagram

Example: For C18*** If the unit is installed at 10 m distance, the quantity of

additional refrigerant should be 50 g .... (10-7.5) m x

20 g/m = 50 g

+ 69 hidden pages