Panasonic CQ-C1101W, CQ-C1121W User Manual
R
A
N
D
O
M
CQ-C1121W
7MUTE 891011 12
SQ/SCAN
P
U
S
H
S
E
L
T
U
N
E
/
T
R
A
C
K
BAND
1 2 3 4 5 6
PWR
CLOCK
V
O
L
SRC
DISP
APM
D
·
M
R
E
P
D
·
M
R
E
P
D
·
M
R
E
P
(CQ-C1121W)
English
Before Reading These Instructions
MUTE
PWR
MODE
VOL
BAND
Battery
Installation
The 24-hour system is used for the clock.
1
Turn the ignition switch
until the accessory indicator lights.
2
Press [SRC] (PWR:
Power).
3
Press [DISP] (CLOCK).
4
Hold down [DISP] (CLOCK) for more than
2 seconds.
5
Adjust the hour.
[[]: sets the hour ahead.
[]]: sets the hour back.
6
Press [DISP] (CLOCK).
7
Adjust the minute.
[[]: sets the minute ahead.
[]]: sets the minute back.
8
Press [DISP] (CLOCK).
Notes:
¡ “AdJ” is displayed before adjusting the clock.
¡ Hold down []] or [[] to change numbers rapidly.
Clock Display at Power Off
Press [DISP] (Display) to change the display.
Clock Setting
Display off
Clock display
Pull the insulation film out from
the backside of the remote control gently.
nly
Note: Battery Information:
Battery Type: Panasonic lithium battery (CR2025) (Included
in the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
ACC
ON
Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine
exterior cleaning. Never use benzine, thinner, or other solvents.
Cleaning the
Unit
Fuse
Anti-Theft System
This unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.
Removing
1
Turn off the power.
2
Press []. The removable face plate will
open.
3
Pull it out toward you.
Mounting
1
Slide the left side of the removable face
plate in place.
2
Press the right end of removable face plate
until a “click” is heard.
Caution
¡ This face plate is not waterproof. Do not expose it to
water or excessive moisture.
¡ Do not remove the face plate while driving your car.
¡ Do not place the face plate on the dashboard or nearby
areas where the temperature rises high.
¡ Do not touch the contacts on the face plate and the main
unit, since this may result in poor electrical contact.
¡ If dirt or other foreign substances get on the contacts,
wipe them off with a clean and dry cloth.
Face Plate Removing/Mounting
(Anti-Theft System)
If the replaced fuse fails, contact your nearest authorized Panasonic Service center.
Warning
¡ Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit direct-
ly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your nearest authorized
Panasonic Service Center.
2
1
2
1
Caution
Observe the following cautions when using this
unit.
❑
Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and traffic
conditions while driving.
❑
This unit is designed for use exclusively in automobiles.
❑
Do not operate the unit for a prolonged period with the
engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
❑
Do not expose the unit to direct sunlight or excessive
heat.
Otherwise these will raise the interior temperature of the unit,
and it may lead to smoke, fire, or other damage to the unit.
❑
Do not use the product where it is exposed to water,
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially sure
that the unit does not get wet in car washes or on rainy days.
Observe the following cautions when installing.
❑
Refer wiring and installation to qualified service personnel.
Installation of this unit requires special skills and experience. For
maximum safety, have it installed by your dealer. Panasonic is
not liable for any problems resulting from your own installation
of the unit.
❑
Follow the instructions to install and wire the product.
Not following the instructions to properly install and wire the
product could cause an accident or fire.
❑
Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent them
from getting caught in the vehicle chassis, screws, and moving
parts such as seat rails. Do not scratch, pull, bend or twist the
leads. Do not run them near heat sources or place heavy objects
on them. If leads must be run over sharp metal edges, protect
the leads by winding them with vinyl tape or similar protection.
❑
Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools to
install the product. The use of parts other than those supplied or
designated may result in internal damage to the unit. Faulty
installation may lead to an accident, a malfunction or fire.
❑
Do not block the air vent or the cooling plate of the unit.
Blocking these parts will cause the interior of the unit to overheat and will result in fire or other damage.
❑
Do not install the product where it is exposed to strong
vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If the
installation is not stable, the unit may fall down while driving and
this can lead to an accident or injury.
❑
Installation Angle
The product should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30˚.
The user should bear in mind that in some areas there may be
restrictions on how and where this unit must be installed.
Consult your dealer for further details.
❑
Wear gloves for safety. Make sure that wiring is completed before installation.
❑
To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
❑
Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
Observe the following cautions when handling the
battery for the remote control unit.
●
Use only specified battery (CR2025).
●
Match the polarity of the battery with the (+) and (–) marks in
the battery case.
●
Replace dead battery as soon as possible.
●
Remove the battery from the remote control unit when not using
it for an extended period of time.
●
Insulate the battery (by placing them in a plastic bag or covering
them with vinyl tape) before disposal or storage.
●
Dispose of the battery according to the local regulations.
●
Do not disassemble, recharge, heat or short the battery. Do not
throw a battery into a fire or water.
In case of battery leakage
●
Thoroughly wipe the battery liquid off the battery case and insert
new battery.
●
If any part of your body or clothing comes into contact with battery liquid, wash it with plenty of water.
●
If battery liquid comes into contact with your eyes, wash them
with plenty of water and get immediate medical attention.
Caution
THIS PRODUCT UTILIZES A CLASS ILASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
Specifications
CD Player/Receiver
CQ-C1121W/C1101W/C1001W
Operating Instructions
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and
assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of
enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.
This operating instruction manual is for 3 models CQ-C1121W, CQ-C1101W and CQ-C1001W. All illustrations throughout this
manual represent model CQ-C1121W unless otherwise specified. The following table describes the differences among 3 models.
Features
Models
CQ-C1121W CQ-C1101W CQ-C1001W
Volume control Rotary knob Rotary knob Button
Remote control function Yes (Included) No No
Pre-amp. output connector Rear/Front Rear Rear
Differences between 3 models
General
Power supply : 12 V DC (11 – 16 V DC), negative
ground
Current consumption :Less than 2.2 A (CD mode; 0.5 W 4
channels)
Maximum power output :50 W x 4 (at 1 kHz), volume control
maximum (for CQ-C1121/C1101W)
:45 W x 4 (at 1 kHz), volume control
maximum (for CQ-C1001W)
Tone adjustment range :Bass: ±12 dB at 100 Hz, Treble: ±12
dB at 10 kHz
Speaker impedance :4 – 8 Ω
Pre-amp output voltage :2.5 V (CD mode, 1 kHz, 0 dB)
Pre-amp output impedance :200 Ω
Dimensions (W x H x D) :178 x 50 x 160 mm
Weight :1.3 kg
CD Player
Sampling frequency :8 times oversampling
DA converter :1 bit DAC System
Pick-up type :Astigma 3–beam
Light source :Semiconductor laser
Wave length : 790 nm
Frequency response :20 Hz – 20 kHz (±1 dB)
Signal to noise ratio :96 dB
Total harmonic distortion :0.01 % (1 kHz)
Wow and flutter :Below measurable limits
Channel separation :75 dB
FM Stereo Radio
Frequency range :87.5 MHz – 108 MHz
Usable sensitivity :6 dB/µV (75 Ω)
Frequency response :30 Hz – 15 kHz (±3 dB)
Alternate channel selectivity :75 dB
Stereo separation :35 dB (1 kHz)
Image rejection ratio :75 dB
IF rejection ratio :100 dB
Signal to noise ratio :62 dB
AM Radio
Frequency range :531 kHz – 1 602 kHz
Usable sensitivity :28 dB/µV (S/N 20 dB)
Note:
¡ Specifications and design are subject to modification without
notice due to improvements.
¡ Some figures and illustrations in this manual may be different
from your product.
Matsushita Electric Industrial Co., Ltd.
Web Site: http://www.panasonic.co.jp/global/
Preparation
YFM284C450ZB TAMACO1104-1124 Printed in China
¡Please read these instructions carefully before using this product and keep this manual for future reference.
Maintenance
Accessories
POWER
MUTE
MUTE
PWR
Operating Instructions
(English: YFM284C450ZA)
(кЫТТНЛИ: YFM284C451ZA)
(: YFM284C452ZA)
(YFM284C453ZA : )
Q'ty: 1 set
Installation Instructions
(YFM284C449ZA)
Q'ty: 1
Notes:
¡ The number in parentheses underneath each accessory part name is the part number for maintenance and service.
¡ Accessories and their part numbers are subject to modification without prior notice due to improvements.
¡ Mounting Collar and Trim Plate are mounted on the main unit at shipment. *
PWR
MODE
MODE
BAND
BAND
Remote Control Unit
VOL
VOL
TUNE
TRACK
(include a battery, only
CAR AUDIO
for CQ-C1121W)
(EUR7641020)
Lock Cancel Plate
(FX0214C385ZA)
Mounting Bolt
(YEJV014C002N)
Rubber Bushing
(YFS014C095ZA)
Q'ty: 1
Q'ty: 2
Q'ty: 1
Q'ty: 1
Mounting Collar *
(FX0214C384ZA)
Trim Plate *
(YFC054C081ZA:
CQ-C1121/1101W)
(YFC054C079ZA: CQ-C1001W)
Power Connector
(YEAJ02877)
Safety Information
Q'ty: 1
Q'ty: 1
Q'ty: 1
■
Read the operating instructions for the unit and all other components of your car audio system carefully before using the system.
They contain instructions about how to use the system in a safe and
effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this
manual.
This pictograph intends to alert you to the presence of
important operating instructions and installation instruc-
Warning
tions. Failure to heed the instructions may result in
severe injury or death.
Warning
Observe the following warnings when using this
unit.
❑
The driver should neither watch the display nor operate
the system while driving.
Watching the display or operating the system will distract the driver from looking ahead of the vehicle and can cause accidents.
Always stop the vehicle in a safe location and use the parking
brake before watching the display or operating the system.
❑
Use the proper power supply.
This product is designed for operation with a negative grounded
12 V DC battery system. Never operate this product with other battery systems, especially a 24 V DC battery system.
❑
Keep batteries and insulation film out of reach of infants.
Batteries and insulation film can be ingested, so keep them out of
the reach of infants. If an infant ingests a battery or insulation film,
please seek immediate medical attention.
❑
Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑
Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be repaired, consult your
dealer or an authorized Panasonic Service Center.
❑
Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an abnormal
state (has foreign objects in it, is exposed to water, is smoking, or
smells), turn it off immediately and consult your dealer.
❑
The remote control unit should not lie about in the car.
If the remote control unit lies about, it could fall on the floor while
driving, get wedged under the brake pedal, and lead to a traffic
accident.
❑
Refer fuse replacement to qualified service personnel.
When the fuse blows out, eliminate the cause and have it replaced
with the fuse prescribed for this unit by a qualified service engineer. Incorrect replacement of the fuse may lead to smoke, fire,
and damage to the product.
■
This manual uses pictographs to show you how to use the product
safely and to alert you to potential dangers resulting from improper
connections and operations. The meanings of the pictographs are
explained below. It is important that you fully understand the meanings of the pictographs in order to use this manual and the system
properly.
This pictograph intends to alert you to the presence of
important operating instructions and installation instruc-
Caution
tions. Failure to heed the instructions may result in
injury or material damage.
Observe the following warnings when installing.
❑
Disconnect the lead from the negative (–) battery terminal before installation.
Wiring and installation with the negative (–) battery terminal connected may cause electrical shock and injury due to a short circuit.
Some cars equipped with the electrical safety system have specific
procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM
RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL
INJURY OR DEATH.
❑
Never use safety-related components for installation,
grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank, brake,
suspension, steering wheel, pedals, airbag, etc.) for wiring or fixing the product or its accessories.
❑
Installing the product on the air bag cover or in a location
where it interferes with airbag operation is prohibited.
❑
Check for piping, gasoline tank, electric wiring, and other
items before installing the product.
If you need to open a hole in the vehicle chassis to attach or wire
the product, first check where the wire harness, gasoline tank, and
electric wiring are located. Then open the hole from outside if possible.
❑
Never install the product in a location where it interferes
with your field of vision.
❑
Never have the power cord branched to supply other
equipment with power.
❑
After installation and wiring, you should check the normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may cause
fire, electrical shock or a traffic accident.
❑
In the case of installation to an airbag-equipping car,
confirm warnings and cautions of the vehicle manufacturer before installation.
❑
Make sure the leads do not interfere with driving or getting in and out of the vehicle.
❑
Insulate all exposed wires to prevent short circuiting.
General
R
A
N
D
O
M
CQ-C1121W
7MUTE 891011 12
SQ/SCAN
P
U
S
H
S
E
L
T
U
N
E
/
T
R
A
C
K
BAND
1 2 3 4 5 6
PWR
CLOCK
VO
L
SRC
DISP
APM
D
·
M
R
E
P
D
·
M
R
E
P
D
·
M
R
E
P
SRC
D
·
M
General Operations
Power On/Off
Turn your car's ignition switch to the ACC or ON position.
Power on: Press [SRC] (PWR).
Power off: Hold down [SRC] (PWR) for
more than 1 second.
Source Selection
Press [SRC] to change the source.
Volume Adjustment
(Setting Range: 0 to 40, Default: 18)
Turn [VOL].
Press [VOLUME
▲] or [VOLUME▼].
Mute
ON: Press [MUTE]. ( lights.)
OFF: Press [MUTE] again.
SQ (Sound Quality)
SQ is a function that can call up various sound types at
the touch of button in accordance with your listening
music type.
Press [SQ] to select the sound type as follows:
Note:
Settings of SQ, bass and treble are influenced
one another. If such an influence causes distortion to
the audio signal, readjust bass/treble or volume.
CQ-C1001W
CQ-C1101WCQ-C1121W
[MUTE]
toggles mute on/off.
lights when mute is on.
Remote Control Sensor
(only for CQ-C1121W)
[VOL] (Volume) (Turn)
[VOLUME
▲] [VOLUME▼] (Press)
adjusts the volume.
CQ-C1001W
CQ-C1101WCQ-C1121W
[SRC] (Source)
selects a source.
(PWR) (Power)
toggles power on/off.
[D•M] (Direct Memory)
tunes into the station memorized in D•M.
(Hold it down for more than 2 seconds to
memorize the current station.)
[SQ] (Sound Quality)
selects a sound type (SQ).
Radio Disc Player
MUTE
V
O
L
U
M
E
BAND
PWR
SRC
APM
SEL
SEL
(FLAT) flat frequency response:
does not emphasize any part. (Default)
(ROCK) speedy and heavy sound:
exaggerates bass and treble.
(POP) wide-ranged and deep sound:
slightly emphasizes bass and treble.
(VOCAL) clear sound:
emphasizes middle tone and slightly emphasizes treble.
Radio (FM/AM)
R
A
N
D
O
M
CQ-C1121W
7MUTE 89 1011 12
SQ/SCAN
P
U
S
H
S
E
L
T
U
N
E
/
T
R
A
C
K
BAND
1 2 3 4 5 6
PWR
CLOCK
VOL
SRC
DISP
APM
D
·
M
R
E
P
D
·
M
R
E
P
D
·
M
R
E
P
BAND
1 2 3 4 5 6
SRC
DISP
D
·
M
[TUNE ]] [TUNE []
down/up the frequency. (Hold it down for
more than 2 seconds for seek tuning.)
[BAND]
selects a band in the radio source.
(APM) (
Auto Preset Memory)
executes APM in the radio source. (Hold it
down for more than 2 seconds.)
[DISP] (Display)
switches the information on
the display.
[D•M] (Direct Memory)
tunes into the station memorized in D•M.
(Hold it down for more than 2 seconds to
memorize the current station.)
[SRC] (Source)
selects a source.
Preset buttons [1] to [6]
selects a preset station in the radio source,
and presets the current station. (Hold it down
for more than 2 seconds.)
Operation Flow
1
Press [SRC] to select the radio source.
2
Press [BAND] to select a band.
3
Select a station.
Frequency adjustment
[TUNE]]: Lower
[TUNE[]: Higher
Note: Hold down either of them for more than 0.5
seconds and release it for station search.
Preset station selection
Press the corresponding preset button from [1] to [6] to
tune in a preset station.
R
A
N
D
O
M
CQ-C1121W
7MUTE 891011 12
SQ/SCAN
P
U
S
H
S
E
L
T
U
N
E
/
T
R
A
C
K
BAND
1 2 3 4 5 6
PWR
CLOCK
VOL
SRC
DISP
APM
D
·
M
R
E
P
D
·
M
R
E
P
D
·
M
R
E
P
DISP
[DISP] (Display)
exits from the audio menu.
[VOL]
selects a value in the audio menu.
(PUSH SEL) (Push to Select)
selects items in the audio menu.
CQ-C1101WCQ-C1121W
[▲] or [▼]
selects a value in the audio menu.
[SEL] (Select)
selects items in the audio menu.
CQ-C1001W
Audio menu
1
Display the audio menu.
Press [VOL] (PUSH SEL).
Press [SEL].
Note: If no operation takes place for more than 5 seconds
in the audio menu (2 seconds in Main volume adjustment),
the display returns to the regular mode.
CQ-C1001W
CQ-C1101WCQ-C1121W
2
Select a mode to be adjusted.
Press [VOL] (PUSH SEL).
Press [SEL].
CQ-C1001W
CQ-C1101WCQ-C1121W
3
Adjust.
Turn [VOL].
Press [▲] or [▼].
CQ-C1001W
CQ-C1101WCQ-C1121W
(Setting Range: 0 to 40, Default: 18) [▲]: Up
[▼]: Down
(Setting Range: –12 dB to +12 dB by 2 dB,
Default: 0 dB)
[▲]: Increased
[▼]: Decreased
(Setting Range: –12 dB to +12 dB by 2 dB,
Default: 0 dB)
[▲]: Increased
[▼]: Decreased
(Setting Range: 15 levels each and 0 (center),
Default 0)
[▲]: Right enhanced
[▼]: Left enhanced
(Setting Range: 15 levels each and 0 (center),
Default 0)
[▲]: Front enhanced
[▼]: Rear enhanced
Volume
Bass
Treble
Balance
Fader
MUTE
V
O
L
U
M
E
BAND
PWR
SRC
APM
SELSEL
SEL
SEL
Note: If the fader is set to front, the pre-amp. output
(rear) is decreased.
[▲]
[▼]
Remote Control Unit (only for CQ-C1121W)
Note: This operating instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)
Battery Replacement
Battery Notes
[PWR] (POWER)
toggles power on/off.
[MODE]
selects a mode. (source)
MUTEMUTE
PWR
MODEMODE
VOL
CAR AUDIO
MUTE
PWR
MODE
BANDBANDBAND
VOL
TUNE
TRACK
POWER
[BAND]
selects a band in the radio source,
toggles pause/play in the player source,
and executes APM in the radio source.
(Hold it down for more than 2 seconds.)
[MUTE]
toggles mute on/off.
[VOL}] [VOL{]
adjust the volume.
[TUNE]] [TUNE[]
down/up the frequency. (Hold it down for
more than 2 seconds for seek tuning.)
[TRACK s] [TRACK d]
skip to the previous/next track in the
player mode.
Hold it down for fast reverse/fast forward.
Warning
¡Keep batteries away from children to avoid the risk of
accidents. If an infant ingests a battery, please seek
immediate medical attention.
Caution
¡ Remove and dispose of the old battery immediately.
¡ Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
¡ Follow local regulations when disposing of a battery.
¡Improper use of batteries may cause overheating, an
explosion or ignition, resulting in injury or a fire.
Note: Battery Information:
Battery Type: Panasonic lithium battery (CR2025) (Included
in the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
q
w
q Remove the battery holder
with the remote control unit
placed on a flat surface.
q Stick your thumbnail into
the groove, and push the
holder in the direction of
the arrow at the same
time.
w Pull it out in the direction
of the arrow using a
tough pointed object.
2
3
w Put a battery in the case
with (+)-side facing up.
e Put the case back.
Tough pointed object
Back side
R
A
N
D
O
M
CQ-C1121W
7MUTE 89 1011 12
SQ/SCAN
P
U
S
H
S
E
L
T
U
N
E
/
T
R
A
C
K
BAND
1 2 3 4 5 6
PWR
CLOCK
VOL
SRC
DISP
APM
D
·
M
R
E
P
D
·
M
R
E
P
D
·
M
R
E
P
BAND
1 2 3 4 5 6
SRC
DISP
R
E
P
Disc slot
takes a disc in with the label-side facing up.
Note: The power will be turned on automatically
when a disc is loaded.
(y/5) (Pause/Play)
toggles pause/play in the play-
er source.
[DISP] (Display)
switches the information on
the display.
[TRACK s] [TRACK d]
skip to the previous/next track in the player
mode.
Hold down either of them for fast reverse/fast
forward.
[SRC] (Source)
selects a source.
[1] to [6]
(7) to (12) (Hold down one of them for
more than 2 seconds.)
select a track directly.
Operation Flow
1
Press [SRC] to select the Disc Player
source.
2
Select a desired portion.
Track selection
Press [TRACK s] / [TRACK d].
Note: To perform fast forward/reverse, hold down either
of them.
Pause
Press [BAND] (y/5).
Press again to cancel.
Direct track selection
Press a track number button from [1] to [6].
¡ The corresponding track (1–6) starts playing.
Hold down a track number button from [1]
to [6] ((7) to (12)) for more than 2 seconds.
¡ The corresponding track (7–12) starts playing.
[u] (Eject)
ejects the disc.
(SCAN)
toggles on/off the scan play. (Hold it down for more than 2
seconds.)
Caution
¡ Do not insert a disc when the indicator lights.
¡ Refer to the section of “Notes on Discs”.
¡ This unit does not support 8 cm discs.
¡ If you insert an 8 cm disc and cannot eject it, turn ACC of your car off once and turn it on again, then press [u] (Eject).
¡ This unit does not support MP3 and WMA disc playback.
¡ This unit does not support CD text display.
¡ Do not insert foreign matter into the disc slot.
[REP] (Repeat)
toggles on/off the repeat play.
(RANDOM)
toggles on/off the random play. (Hold it down
for more than 2 seconds.)
No sound
● Disable the mute function.
● Verify the wiring.
● Wait until the dew disappears before
turning on the unit.
Noise
● Make sure that grounding is established
properly.
Common
Frequent
noise
● Tune in to another station of high-inten-
sity waves.
● Make sure that the antenna mounted
point is grounded properly.
Radio
Preset data
deleted
● The preset memory is cleared to return
to the original factory setting when the
power connector or battery is disconnected.
No sound, or disc
is automatically
ejected
● Load the disc correctly.
● Clean the disc.
CD Player
Sound skip,
poor sound
quality
● Clean the disc.
Sound skip
due to
vibration
● The maximum permissible tilt angle is
30°.
● Secure the unit.
Disc not
ejectable
● Press [u]. If the disc is still not eject-
ed, contact the nearest Panasonic
Service Center.
No sound from
left, right, front,
or rear speaker
● Adjust the balance and fader.
● Verify the wiring.
Trouble
Check point
Left and right
sounds are
reversed
● Connect the speaker lead correctly.
Error Display Messages
(The disc is ejected automatically.)
The disc is dirty, or is upside down.
The disc has scratches.
● Check the disc.
No operation by some cause.
● If normal operation is not restored, call
the store where you purchased the unit
or the nearest Service Center to ask for
repairs.
If You Suspect Something Wrong
Check and take steps as described below.
If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic Service
Center. The product should be serviced only by qualified personnel.
Please refer the checking and the repair to professionals. Panasonic
shall not be liable for any accidents arising out of neglect of checking
the unit or your own repair after your checking.
Warning
¡ Do not use the unit in an irregular condition, for example, with-
out sound, or with smoke or a foul smell, which can cause
ignition or electric shock. Immediately stop using the unit and
consult your dealer.
¡ Never try to repair the unit by yourself because it is dangerous
to do so.
Audio Settings
lights while receiving an FM stereo signal.
lights while receiving the D•M station.
Radio Source Display
Up to 6 stations can be preset in AM, FM1, FM2, and FM3
respectively.
Preset stations can be simply called up by pressing one of the
preset buttons from [1] to [6].
Auto Preset Memory (APM)
With this operation, stations with good receiving conditions can
be automatically stored in the preset memory.
Select a band.
1
Hold down [BAND] (APM) for more than 2
2
seconds.
Station Preset
The preset stations under best receiving conditions are
received for 5 seconds each after presetting the stations
(SCAN). To stop scanning, press one of the preset buttons from [1] to [6].
Note: New stations overwrite existing saved stations.
Display change
Band Preset NumberFrequency
Press [DISP] to change the display.
Radio source display (Default)
Clock display
Manual station preset
Tune into a station.
1
Hold down one of the preset buttons from
2
[1] to [6] for more than 2 seconds.
(blinks once.)
Note: New stations overwrite existing saved stations.
Disc Player
You can assign your favorite broadcasting station to the
[D•M] (Direct Memory) button. As the result of doing that,
your favorite broadcasting station can be received even if the
unit is turned off, or the CD mode is activated.
D•M station calling
Press [D•M].
Direct Memory
1
Press again to cancel.
Random indicator
Play time
lights when a disc is in the player.
Repeat indicator
Player Source Display
Random play
All the available tracks are played in a random sequence.
Hold down [REP] (RANDOM) for more than
2 seconds.
Hold down again to cancel.
Repeat play
The current track is repeated.
Press [REP].
Random, Repeat, Scan
Notes on discs
Press again to cancel.
Notes on CD/CD Media
If you use commercial CDs, they must
have the label shown at right.
Some copy-protected music CDs are not
playable.
How to hold a disc
¡ Do not touch the underside of a disc.
¡ Do not scratch on a disc.
¡ Do not bend a disc.
¡ When not in use, keep a disc in a case.
Do not use irregularly shaped discs.
Do not leave discs in the following places:
¡ In direct sunlight
¡ Near car heaters
¡ Dirty, dusty and damp areas
¡ Seats and dashboards
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Do not attach any seals or labels to your discs.
Do not write on the disc label with a ballpoint pen
or other hard-point pens.
Track number
D•M station writing
Select a station you would like to preset.
1
Hold down [D•M] for more than 2 seconds.
2
Display change
Press [DISP] to change the display.
Player source display (Default)
Clock display
Scan play
The first 10 seconds of each track is played in sequence.
Hold down [SQ] (SCAN) for more than 2
seconds.
(blinks during scanning.)
Hold down again to cancel.
Notes on CD-Rs/RWs
¡ You may have trouble playing back some CD-R/RW discs
recorded using CD recorders (CD-R/RW drives), either due
to their recording characteristics or dirt, fingerprints,
scratches, etc. on the disc surface.
¡ CD-R/RW discs are less resistant to high temperatures and
high humidity than ordinary music CDs. Leaving them
inside a car for extended periods may damage and make
playback impossible.
¡ Some CD-R/RWs cannot be played back successfully due
to incompatibility among writing software, a CD recorder
(CD-R/RW drive) and the discs.
¡ This player cannot play the CD-R/RW discs if the session is
not closed.
¡ This player cannot play the CD-R/RW discs which contain
other than CD-DA data (MP3/WMA, Video CD, etc.).
¡ Be sure to observe the instructions of the CD-R/RW disc
for handling it.
Troubleshooting
Trouble
No power
● Start the engine. (Or turn the ignition
switch to the ACC position.)
● Verify the wiring. (Ex. battery lead,
power lead, ground lead, etc.)
● Fuse blown (Contact the nearest
Panasonic Service Center.)
● Ask a professional for fuse replacement.
● Be sure to use the same rated fuse.
Check point
Loading...