Panasonic CQ-C1011NW, CQ-C1001NW, CQ-C1021NW User Manual

Accessories

Operating Instructions

(English : YFM284C454ZA) (Deutsch : YFM284C455ZA) (Français : YFM284C456ZA) (Nederlands : YFM284C457ZA) (Svenska : YFM284C458ZA) (Italiano : YFM284C459ZA) (Español : YFM284C460ZA) (Dansk : YFM284C461ZA)

Q'ty: 1 set

Installation Instructions

(English, Deutsch, Français, Nederlands : YFM284C466ZA) (Svenska, Italiano, Español, Dansk : YFM284C467ZA)

Q'ty: 1 set

Warranty Card

Q'ty: 1

Lock Cancel Plate

(FX0214C385ZA)

Q'ty: 2

Mounting Bolt

(YEJV014C002N)

Q'ty: 1

Mounting Collar

(FX0214C384ZA)

Q'ty: 1

Trim Plate

(YFC054C079ZA)

Q'ty: 1

Power Connector

(YEAJ02874)

Q'ty: 1

Notes:

¡ The number in parentheses underneath

each accessory part name is the part number for maintenance and service.

¡ Accessories and their part numbers are

subject to modification without prior notice due to improvements.

¡ Mounting Collar and Trim Plate are

mounted on the main unit at shipment.

CD Player/Receiver

CQ-C1021NW/C1011NW/C1001NW

Operating Instructions

¡Please read these instructions carefully before using this product and keep this manual for future reference.

SEL

(CQ-C1021NW)

Specifications

YFM284C454ZC TAMACO1004-2055 Printed in China

General

Power Supply :12 V DC (11 V – 16 V), Negative

Ground Tone Controls (Bass) :±12 dB (100 Hz) Tone Controls (Treble) :±12 dB (10 kHz) Current Consumption :Less than 2.5 A (CD mode, 0.5 W

4 channels) Maximum Power Output :45 W x 4 (4 Ω) Speaker Impedance :4 – 8 Ω Pre-Amp Output Voltage :2.5 V (CD mode, 1 kHz, 0 dB) Pre-Amp Output Impedance :200 Ω Dimensions (Main Unit) :178(W) x 50(H) x 160(D) mm Weight (Main Unit) :1.3 kg

CD Player

Sampling frequency :8 times oversampling DA converter :1 bit DAC System Pick-up type :Astigma 3-beam Light source :Semiconductor laser Wave length : 790 nm Frequency response :20 Hz – 20 kHz (±1 dB) Signal to noise ratio :96 dB Total harmonic distortion :0.01 % (1 kHz) Wow and flutter :Below measurable limits Channel separation :75 dB

FM Stereo Radio

Frequency Range :87.5 MHz – 108 MHz Usable Sensitivity :6 dB/µV (S/N 30 dB) Stereo Separation :35 dB (1 kHz)

AM (MW) Radio

Frequency Range :531 kHz – 1 602 kHz Usable Sensitivity :28 dB/µV (S/N 20 dB)

AM (LW) Radio

Frequency Range :153 kHz – 279 kHz Usable Sensitivity :32 dB/µV (S/N 20 dB)

Notes:

¡ Specifications and design are subject to modification without

notice due to improvements.

¡ Some figures and illustrations on this manual may be different

from real ones.

Matsushita Electric Industrial Co., Ltd.

Web Site: http://www.panasonic.co.jp/global/

English

Before Reading These Instructions

Panasonic welcomes you to our constantly growing family of electronic products owners. We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.

Laser Product

Differences among 3

models

This operating instruction manual is for 3 models CQ-C1021NW, CQ-C1011NW and CQ-C1001NW. All illustrations throughout this manual represent model CQ-C1021NW unless otherwise specified. The following table describes the differences among 3 models.

Label Indications and Their Locations

CAUTION

LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.

Caution

This product utilizes a laser.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Do not take apart this unit or attempt to make any changes yourself.

This unit is a very intricate device that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet.

Therefore, never try to disassemble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages.

CLASS 1 LASER PRODUCT

Caution Label

Deck Ass’y (in the unit, upper side)

Preparation

The 24-hour system is used for the clock. Notes:

¡ Adjust the clock when “NO CT” appears on the dis-

play.

¡ When a broadcast of FM Radio Data System is

received, the clock is set automatically by the CT (Clock Time) service.

¡ Hold down []] or [[] to change numbers rapidly.

Select the radio AM mode.

(a “Radio (AM [LW/MW]/FM)”)

Hold down [DISP] (CT) for more than 2 seconds.

Hour blinks

Adjust the hour.

Hour entered

[[]: sets the hour ahead. []]: sets the hour back.

Press [DISP] (CT).

Minute blinks

Adjust the minute.

Minute entered

[[]: sets the minute ahead. []]: sets the minute back.

Press [DISP] (CT).

Completed

Clock Setting

Features

Models

CQ-C1021NW CQ-C1011NW CQ-C1001NW

Display colour Blue Black Black

Key/disc slot illumination colour Red Red Green

Maintenance

Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine exterior cleaning. Never use benzine, thinner, or other solvents.

Cleaning the

Unit

Fuse

Anti-Theft System

This unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.

Removing

Turn off the power.

Press []. The face plate will open.

Pull it out toward you.

Mounting

Slide the left side of the face plate in place.

Press the right end of face plate until a “click” is heard.

Caution

¡ This face plate is not waterproof. Do not expose it to

water or excessive moisture.

¡ Do not remove the face plate while driving your car. ¡ Do not place the face plate on the dashboard or nearby

areas where the temperature rises high.

¡ Do not touch the contacts on the face plate and the

main unit, since this may result in poor electrical contact.

¡ If dirt or other foreign substances get on the contacts,

wipe them off with a clean and dry cloth.

Face Plate Removing/Mounting

(Anti-Theft System)

If the replaced fuse fails, contact your nearest authorized Panasonic Service Centre.

Warning

¡ Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit

directly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your nearest authorized Panasonic Service Centre.

Troubleshooting

Trouble

Check point

No power

● Start the engine. (Or turn the ignition

switch to the ACC position.)

● Verify the wiring. (Ex. battery lead,

power lead, ground lead, etc.)

● Fuse blown (Contact the nearest

Panasonic Service Centre.)

● Ask a professional for fuse replace-

ment.

● Be sure to use the same rated fuse.

No sound

● Disable the mute function.

● Verify the wiring.

● Wait until the dew disappears before

turning on the unit.

Noise

● Make sure that grounding is established

properly.

Common

Frequent

noise

● Tune into another station of high-inten-

sity waves.

● Make sure that the antenna mounted

point is grounded properly.

Radio

Preset data

deleted

● The preset memory is cleared to return

to the original factory setting when the power connector or battery is disconnected.

No sound, or disc

is automatically

ejected

● Load the disc correctly.

● Clean the disc.

Disc Player

Sound skip,

poor sound

quality

● Clean the disc.

Sound skip

due to

vibration

● The maximum permissible tilt angle is

30°.

● Secure the unit.

Disc not

ejectable

● Press [u]. If the disc is still not eject-

ed, contact the nearest Panasonic Service Centre.

No sound from

left, right, front,

or rear speaker

● Adjust the balance and fader.

● Verify the wiring.

Trouble

Check point

Left and right

sounds are

reversed

● Connect the speaker lead correctly.

Error Display Messages

(The disc is ejected automatically.) The disc is dirty, or is upside down. The disc has scratches.

● Check the disc.

No operation by some cause.

● If normal operation is not restored, call

the store where you purchased the unit or the nearest Panasonic Service Centre to ask for repairs.

If You Suspect Something Wrong

Check and take steps as described below.

If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic Service Centre. The product should be serviced only by qualified personnel. Please refer the checking and the repair to professionals. Panasonic shall not be liable for any accidents arising out of neglect of checking the unit or your own repair after your checking.

Warning

¡ Do not use the unit in an irregular condition, for example, with-

out sound, or with smoke or a foul smell, which can cause ignition or electric shock. Immediately stop using the unit and consult your dealer.

¡ Never try to repair the unit by yourself because it is dangerous

to do so.

Safety Information

Warning

Observe the following warnings when using this unit.

❑

The driver should neither watch the display nor operate the system while driving.

Watching the display or operating the system will distract the driver from looking ahead of the vehicle and can cause accidents. Always stop the vehicle in a safe location and use the parking brake before watching the display or operating the system.

❑

Use the proper power supply.

This product is designed for operation with a negative grounded 12 V DC battery system. Never operate this product with other battery systems, especially a 24 V DC battery system.

❑

Protect the Deck Mechanism.

Do not insert any foreign objects into the slot of this unit.

❑

Do not disassemble or modify the unit.

Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be repaired, consult your dealer or an authorized Panasonic Service Centre.

❑

Do not use the unit when it is out of order.

If the unit is out of order (no power, no sound) or in an abnormal state (has foreign objects in it, is exposed to water, is smoking, or smells), turn it off immediately and consult your dealer.

❑

Refer fuse replacement to qualified service personnel.

When the fuse burns out, eliminate the cause and have it replaced with the fuse prescribed for this unit by a qualified service engineer. Incorrect replacement of the fuse may lead to smoke, fire, and damage to the product.

Observe the following warnings when installing.

❑

Disconnect the lead from the negative (–) battery terminal before installation.

Wiring and installation with the negative (–) battery terminal connected may cause electrical shock and injury due to a short circuit. Some cars equipped with the electrical safety system have specific procedures of battery terminal disconnection.

FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH.

❑

Never use safety-related components for installation, grounding, and other such functions.

Do not use safety-related vehicle components (fuel tank, brake, suspension, steering wheel, pedals, airbag, etc.) for wiring or fixing the product or its accessories.

❑

Installing the product on the air bag cover or in a location where it interferes with airbag operation is prohibited.

❑

Check for piping, gasoline tank, electric wiring, and other items before installing the product.

If you need to open a hole in the vehicle chassis to attach or wire the product, first check where the wire harness, gasoline tank, and electric wiring are located. Then open the hole from outside if possible.

❑

Never install the product in a location where it interferes with your field of vision.

❑

Never have the power cord branched to supply other equipment with power.

❑

After installation and wiring, you should check the normal operation of other electrical equipment.

The continuation of their using in abnormal conditions may cause fire, electrical shock or a traffic accident.

❑

In the case of installation to an airbag-equipping car, confirm warnings and cautions of the vehicle manufacturer before installation.

❑

Make sure the leads do not interfere with driving or getting in and out of the vehicle.

❑

Insulate all exposed wires to prevent short circuiting.

Caution

Observe the following cautions when using this unit.

❑

Keep the sound volume at an appropriate level.

Keep the volume level low enough to be aware of road and traffic conditions while driving.

❑

This unit is designed for use exclusively in automobiles.

❑

Do not operate the unit for a prolonged period with the engine turned off.

Operating the audio system for a long period of time with the engine turned off will drain the battery.

❑

Do not expose the unit to direct sunlight or excessive heat.

Otherwise these will raise the interior temperature of the unit, and it may lead to smoke, fire, or other damage to the unit.

❑

Do not use the product where it is exposed to water, moisture, or dust.

Exposure of the unit to water, moisture, or dust may lead to smoke, fire, or other damage to the unit. Make especially sure that the unit does not get wet in car washes or on rainy days.

Observe the following cautions when installing.

❑

Refer wiring and installation to qualified service personnel.

Installation of this unit requires special skills and experience. For maximum safety, have it installed by your dealer. Panasonic is not liable for any problems resulting from your own installation of the unit.

❑

Follow the instructions to install and wire the product.

Not following the instructions to properly install and wire the product could cause an accident or fire.

❑

Take care not to damage the leads.

When wiring, take care not to damage the leads. Prevent them from getting caught in the vehicle chassis, screws, and moving parts such as seat rails. Do not scratch, pull, bend or twist the leads. Do not run them near heat sources or place heavy objects on them. If leads must be run over sharp metal edges, protect the leads by winding them with vinyl tape or similar protection.

❑

Use the designated parts and tools for installation.

Use the supplied or designated parts and appropriate tools to install the product. The use of parts other than those supplied or designated may result in internal damage to the unit. Faulty installation may lead to an accident, a malfunction or fire.

❑

Do not block the air vent or the cooling plate of the unit.

Blocking these parts will cause the interior of the unit to overheat and will result in fire or other damage.

❑

Do not install the product where it is exposed to strong vibrations or is unstable.

Avoid slanted or strongly curved surfaces for installation. If the installation is not stable, the unit may fall down while driving and this can lead to an accident or injury.

❑

Installation Angle

The product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30˚. The user should bear in mind that in some areas there may be restrictions on how and where this unit must be installed. Consult your dealer for further details.

❑

Wear gloves for safety. Make sure that wiring is completed before installation.

❑

To prevent damage to the unit, do not connect the power connector until the whole wiring is completed.

❑

Do not connect more than one speaker to one set of speaker leads. (except for connecting to a tweeter)

This pictograph intends to alert you to the presence of important operating instructions and installation instructions. Failure to heed the instructions may result in severe injury or death.

■

Read the operating instructions for the unit and all other components of your car audio system carefully before using the system. They contain instructions about how to use the system in a safe and effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this manual.

■

This manual uses pictographs to show you how to use the product safely and to alert you to potential dangers resulting from improper connections and operations. The meanings of the pictographs are explained below. It is important that you fully understand the meanings of the pictographs in order to use this manual and the system properly.

Warning

This pictograph intends to alert you to the presence of important operating instructions and installation instructions. Failure to heed the instructions may result in injury or material damage.

Caution

Sales and Support Information

For UK and Ireland customers only.

Customer Care Centre

¡ For customers within the UK: 08705 357357 ¡ For customers within the Republic of Ireland: 01 289 8333 ¡ Visit our website for product information ¡ E-mail: customer.care@panasonic.co.uk

Direct Sales at Panasonic UK

¡ Order accessories and consumable items for your product

with ease and confidence by phoning our Customer Care Centre Monday - Thursday 9:00am - 5:30pm, Friday 9:30am - 5:30pm. (Excluding public holidays).

¡ Or go on line through our Internet Accessory ordering

application at www.panasonic.co.uk.

¡ Most major credit and debit cards accepted. ¡ All enquiries, transactions and distribution facilities are

provided directly by Panasonic UK Ltd.

¡ It couldn't be simpler! ¡ Also available through our Internet is direct shopping for a

wide range of finished products, so take a browse on our website for further details.

BAND

APM

SEL

PWR

MUTE/SQ

SRC

RANDOM SCAN REPEAT

1 2 3 4 5 6

CQ-C1021N

PTY

DISP

CAUTION - LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM.

VORSICHT - LASERSTRAHLUNG, WENN GEÖFFNET. VERMEIDEN SIE EIN AUSSETZEN GEGENÜBER DEM LASERSTRAHL.

ATTENTION – RAYONNEMENT LASER SI OUVERT, ÉVITER TOUTE EXPOSITION AU FAISCEAU.

ADVARSEL – LASER UDSENDES NÅR DER ER ÅBNET. UNDGÅ UDSÆTTELSE FOR STRÅLER.

VAROITUS – LASERSÄTEILYVAARA AVATTAESSA. VARO ALTISTUMISTA SÄTEELLE.

FÖRSIKTIGHET – LASERSTRÅLNING I ÖPPNAT LÄGE. UNDVIK ATT UTSÄTTAS FÖR STRÅLEN.

ADVARSEL – LASERSTRÅLING. UNNGÅ EKSPONERING FOR STRÅLEN VED ÅPNING.

ЗзаеДзаЦ – гДбЦкзйЦ абгмуЦзаЦ ика йндкхнаа. абЕЦЬДнъ ЗйбСЦвлнЗаь гДбЦкзйЙй абгмуЦзаь.

Audio Settings

SEL

[DISP] (Display) exits from the audio menu.

[

▲] or [▼]

selects a value in the audio menu. [SEL] (Select) selects items in the audio menu.

General

SEL

[MUTE]

toggles mute on/off. (SQ) (Sound Quality) selects a sound type (SQ). (Hold it down for more than 1 second.)

[VOLUME

▲] [VOLUME▼]

adjusts the volume.

[SRC] (Source) selects a source. (PWR) (Power) toggles power on/off.

General Operations

Power On/Off

Set your car's ignition switch to the ACC or ON position.

Power on: Press [SRC] (PWR). Power off: Hold down [SRC] (PWR) for

more than 1 second.

Source Selection

Press [SRC] to change the source.

Volume Adjustment

(Setting Range: 0 to 40, Default: 18) Press [VOLUME

▲] or [VOLUME▼].

Mute

ON: Press [MUTE]. ( lights.)

lights when mute is on

OFF: Press [MUTE] again.

SQ (Sound Quality)

SQ is a function that can call up various sound types at the touch of button in accordance with your listening music type. Hold down [SQ] for more than 1 second to select the sound type as follows:

Note:

Settings of SQ, bass and treble are influenced one another. If such an influence causes distortion to the audio signal, readjust bass/treble or volume.

Radio

Disc Player

(FLAT) flat frequency response: does not emphasize any part. (Default)

(ROCK) speedy and heavy sound: exaggerates bass and treble.

(POP) wide-ranged and deep sound: slightly emphasizes bass and treble.

(VOCAL) clear sound: emphasizes middle tone and slightly emphasizes treble.

Audio menu

Press [

SEL

] to display the audio menu display.

Note: If no operation takes place for more than 5 seconds in the audio menu (2 seconds in Main volume adjust-

ment), the display returns to the regular mode.

Press [SEL]to select a mode to be adjusted.

Press [▲] or [▼] to adjust.

(Setting Range: 0 to 40, Default: 18) [▲]: Up

[▼]: Down

(Setting Range: –12 dB to +12 dB by 2 dB, Default: 0 dB)

[▲]: Increased [▼]: Decreased

(Setting Range: –12 dB to +12 dB by 2 dB, Default: 0 dB)

[▲]: Increased [▼]: Decreased

(Setting Range: 15 levels each, Default: CNT (centre))

[▲]: Right enhanced [▼]: Left enhanced

(Setting Range: 15 levels each, Default: CNT (centre))

[▲]: Front enhanced [▼]: Rear enhanced

Volume

Bass

Treble

Balance

Fader

(Setting Range: 1 to 40, Default: 18) [▲]: Increased

[▼]: Decreased

TA Volume Set

Note: If the fader is set to front, the pre-amp. output (rear) is decreased.

Radio (AM

[LW/MW]

/FM )

SEL

[TUNE ]] [TUNE []

down/up the frequency. (Hold it down for more than 0.5 seconds and release it for seek tuning.)

(MONO/LOC) (Mono/local) selects MONO/LOCAL on/off in the FM mode (Hold it down for more than 2 seconds.), and toggles LOCAL on/off in the AM (LW/MW) mode.

[BAND]

selects a band in the radio source. (APM) (

Auto Preset Memory)

executes APM in the radio source. (Hold it down for more than 2 seconds.)

[DISP] (Display) switches the information on the display.

[SRC] (Source) selects a source.

Preset buttons [1] to [6]

selects a preset station in the radio source, and presets the current station. (Hold it down for more than 2 seconds.)

Operation Flow

Press [SRC] to select the radio source.

Press [BAND] to select a band.

Select a station.

Frequency adjustment

[TUNE]]: Lower [TUNE[]: Higher Note: Hold down either of them for more than 0.5 sec-

onds and release it for seek tuning.

Preset station selection

Press the corresponding preset button from [1] to [6] to tune in a preset station.

Mono/Local selection

Mono: Reduce noise if weak signals are received Local: Only strong signals of stations are searched for in seek tuning.

FM broadcast

Hold down [PTY] (MONO/LOC) for more than 2 seconds to change the mode.

AM (LW/MW) broadcast

Press [PTY] (LOC) to change the mode.

MONO OFF/LOCAL OFF MONO ON/LOCAL OFF

MONO OFF/LOCAL ON MONO ON/LOCAL ON

LOCAL OFF LOCAL ON

lights while mono/local is on.

Station Preset

Up to 6 stations can be preset in AM (LW/MW), FM1, FM2, and FM3 respectively. Preset stations can be simply called up by pressing one of the buttons from [1] to [6].

Auto Preset Memory (APM)

With this operation, stations with good receiving conditions can be automatically stored in the preset memory.

Select a band.

Hold down [BAND] (APM) for more than 2 seconds.

The preset stations under best receiving conditions are received for 5 seconds each after presetting the stations (SCAN). To stop scanning, press one of the buttons from [1] to [6].

Note: New stations overwrite existing saved stations.

Manual station preset

Tune into a station.

Hold down one of the preset buttons from [1] to [6] for more than 2 seconds.

(blinks once)

Note: New stations overwrite existing saved stations.

lights while receiving an FM stereo signal.

Frequency Preset Number

Band

Display change

Press [DISP] to change the display.

Radio Source Display

AM (LW/MW) mode:

Band/frequency

CT Clock Time

FM (not RDS) mode:

Band/frequency

RDS mode:

PS Programme Service Name

Band/frequency

(Default)

Useful functions such as AF, TA, PTY, etc. are available in the RDS (Radio Data System)-ready areas.

Some FM stations are broadcasting added data compatible with RDS. This radio set offers convenient functions using such data.

RDS service availability varies with areas. Please understand if RDS service is not available in your area, the following service is not available, either.

The following functions are available when receiving RDS stations.

AF (Alternative Frequency)

The following functions are available when the AF mode is active ( lights).

¡ When receiving conditions become bad, a station with bet-

ter receiving conditions is automatically tuned into.

¡ When executing APM, only RDS stations are selected. ¡ When calling up a preset station, a best receiving station is

selected automatically. (BSR Best Stations Research)

Notes:

¡ The AF sensitivity can be adjusted. ¡ The AF available range can be adjusted.

TA (Traffic Announcement)

The following functions are available when the TA mode is active ( lights).

¡ A TP station is automatically searched for and received at

the instant of toggling the TA mode on if you are receiving a non-TP station or TP station with poor reception.

¡ When executing station search or APM, only TP stations

are selected.

¡ Setting to TA on with the unit in another mode, it will auto-

matically switch to radio mode and output the traffic announcement when the traffic announcement begins. The traffic announcement having finished, the unit will return to the previous mode. (TA Standby Mode)

PTY (Programme Type)

The following functions are available when the PTY mode is active.

¡ The PTY of receiving station appears. ¡ Programmes can be searched for by PTY.

Note: PTY language can be selected.

Other functions of RDS

CT (Clock Time)

The clock is automatically adjusted.

PS (Programme Service Name)

As well as the frequency, the name of the broadcast station appears.

EON (Enhanced Other Network)

RDS information is updated constantly in response to the current position.

EON-TA

Traffic information from the current and other network stations can be received.

Emergency Announcement Reception

Emergency announcement automatically appears on the display when it is received.

AF Level

Press [AF] to select AF level.

Low level AF operating sensitivity. (Default)

High level AF operating sensitivity.

When the AF network of an RDS station is not required.

AF Range (Region)

Holding down [AF] (REG: Region) for more than 2 seconds toggles region mode on/off.

REG OFF:

The frequency is changed also for programmes outside the region. (Default)

REG ON:

The frequency is changed only for programmes within the region.

PI Seek (Programme Identification Seek)

If reception becomes poor when tuning in a preset station, press the same preset number button. The same station with better reception will be searched for.

Press the same preset number button again to cancel.

Note: For PI Seek, cancel the TA mode first, then execute PI Seek.

AF (Alternative Frequency)

PTY ON/OFF

Pressing [PTY] toggles PTY mode on and off.

Programme Search by PTY

Programmes can be searched for by use of PTY that has been originally preset.

Press [1] to [6] to select PTY in the PTY mode.

Another station in the same PTY is searched for by pressing

[BAND].

Notes:

¡ When there is no corresponding programme type station,

“NONE” is displayed.

¡ A desired PTY appears for 5 seconds. ¡ Preset contents are changeable.

Detailed PTY Selection

Press []] or [[] to select PTY.

Press [BAND].

Search starts.

Notes:

¡ To stop searching, press [BAND] (SET). ¡ When there is no corresponding programme type station,

“NONE” is displayed.

PTY Preset Change

Original PTY presets can be changed as you like.

Select a PTY that you would like to preset.

Follow the procedure of ordinary presetting. (a “Station Preset” in “Radio (AM [LW/MW]/FM)”)

PTY Language Selection

The language displayed on the screen is selectable. (English or Swedish)

Hold down [SEL] for mote than 2 seconds.

Press [▲] or [▼].

Programme Type Contents

1NEWSNEWS 2SPEECH AFFAIRS, INFO, EDUCATE,

DRAMA, CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE,

DOCUMENT 3 SPORT SPORT 4 POP M POP M 5 CLASSICS CLASSICS 6 MUSIC ROCK M, EASY M, LIGHT M,

OTHER M, JAZZ, COUNTRY,

NATION M, OLDIES, FOLK M

PTY (Programme Type)

What is RDS?

TA ON/OFF

Pressing [TA] toggles TA on and off.

Traffic Information Only (TA Mute)

For listening to only traffic information, activate TA and set the volume to 0 in FM mode.

Once traffic information starts, the volume changes to the TA volume. (a “Audio Settings”)

TA (Traffic

Announcement)

Radio Data System (RDS) in FM Broadcasting

Disc Player

SEL

Disc slot

takes a disc in with the printed side facing up. Note: The power will be turned on automatically when a disc is loaded.

(y/5) (Pause/Play) toggles pause/play in the play-

er source.

printed side

[DISP] (Display) switches the information on the display.

[TRACK s] [TRACK d]

skip to the previous/next track in the disc player source. Hold down either of them for fast reverse/fast forward.

[SRC] (Source) selects a source.

(RANDOM)/(SCAN)/(REPEAT)

toggles on/off each play mode.

Operation Flow

Press [SRC] to select the disc player source.

Select a desired portion.

Track selection

Press [TRACK s] / [TRACK d].

Note: To perform fast forward/reverse, hold down

either of them.

Pause

Press [BAND] (y/5). Press again to cancel.

Notes on discs

Notes on CD/CD Media

If you use commercial CDs, they must have the label shown at right. Some copy-protected music CDs are not playable. How to hold a disc

¡ Do not touch the underside of a disc. ¡ Do not scratch on a disc. ¡ Do not bend a disc. ¡ When not in use, keep a disc in a case.

Do not use irregularly shaped discs. Do not leave discs in the following places:

¡ Direct sunlight ¡ Near car heaters ¡ Dirty, dusty and damp areas ¡ Seats and dashboards

Disc cleaning

Use a dry, soft cloth to wipe from the centre outward.

Do not attach any seals or labels to your discs. Do not write on the disc label with a ballpoint pen or other hard-point pens.

Notes on CD-Rs/RWs

¡ You may have trouble playing back some CD-R/RW discs

recorded using CD recorders (CD-R/RW drives), either due to their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.

¡ CD-R/RW discs are less resistant to high temperatures and

high humidity than ordinary music CDs. Leaving them inside a car for extended periods may damage and make playback impossible.

¡ Some CD-R/RWs cannot be played back successfully due

to incompatibility among writing software, a CD recorder (CD-R/RW drive) and the discs.

¡ This player cannot play the CD-R/RW discs if the session is

not closed.

¡ This player cannot play the CD-R/RW discs which contain

other than CD-DA data (MP3/WMA, Video CD, etc.).

¡ Be sure to observe the instructions of the CD-R/RW disc

for handling it.

Random, Repeat, Scan

Random play

All the available tracks are played in a random sequence.

Press [4] (RANDOM). Press again to cancel.

Repeat play

The current track is repeated.

Press [6] (REPEAT). Press again to cancel.

Scan play

The first 10 seconds of each track is played in sequence.

Press [5] (SCAN).

(blinks during scanning)

Press again to cancel.

Display change

Press [DISP] to change the display.

Player Source Display

[u] (Eject) ejects the disc.

Caution

¡ Do not insert a disc when the indicator lights. ¡ Refer to the section of “Notes on Discs”. ¡ This unit does not support 8 cm discs. ¡ If you insert an 8 cm disc and cannot eject it, turn ACC of your

car off once and turn it on again, then press [u] (Eject).

¡ This unit does not support MP3 and WMA disc play-

back.

¡ This unit does not support CD text display. ¡ Do not insert foreign objects into the disc slot.

Player mode display (Default)

Clock display

Play time

repeat indicator

random indicator

indicator

BAND

APM

PWR

SRC

SEL

MUTE/SQ

CQ-C1021N

1 2 3 4 5 6

RANDOM SCAN REPEAT

PTY

DISP

BAND

APM

PWR

SRC

SEL

MUTE/SQ

1 2 3 4 5 6

CQ-C1021N

RANDOM SCAN REPEAT

PTY

DISP

BAND

APM

PWR

SRC

SEL

MUTE/SQ

1 2 3 4 5 6

RANDOM SCAN REPEAT

CQ-C1021N

PTY

/ E

DISP

BAND

APM

PWR

SRC

SEL

MUTE/SQ

1 2 3 4 5 6

CQ-C1021N

RANDOM SCAN REPEAT

4 5 6

PTY

/ E

DISP

SPEECH / MUSIC / NEWS / AFFAIRS / INFO / SPORT / EDUCATE / DRAMA / CULTURE / SCIENCE / VARIED / POP_M / ROCK_M / EASY_M / LIGHT_M / CLASSICS / OTHER_M / WEATHER / FINANCE / CHILDREN / SOCIAL / RELIGION / PHONE_IN / TRAVEL / LEISURE / JAZZ / COUNTRY /

NATION_M

OLDIES / FOLK_M / DOCUMENT

+ 2 hidden pages