PackardBell ML User Manual

Packard Bell
EasyNote ML
Disassembly Manual
11111
Table of Contents
About this Guide...........................................................................................................................2
For More Information ...................................................................................................................2
Technician Notes..........................................................................................................................2
Required Tools.............................................................................................................................2
Hazardous Voltage.......................................................................................................................3
Avoid Electrostatic Discharge .....................................................................................................3
Optical Disk Drive.........................................................................................................................4
Hard Disk Drives...........................................................................................................................5
Memory .........................................................................................................................................6
Keyboard.......................................................................................................................................7
Top Cover.....................................................................................................................................8
LCD Panel................................................................................................................................... 10
Main Board..................................................................................................................................11
Video Board................................................................................................................................12
Heat Sink.....................................................................................................................................13
CPU.............................................................................................................................................13
LCD Assembly............................................................................................................................ 14
Webcam......................................................................................................................................15
Notice ..........................................................................................................................................16
1
Packard Bell EasyNote ML Disas sembly Manual
About this Guide
This guide contains systematic di sassembly instructions for the Packard Bell EasyNote ML. The instructions are illustrated where necessary with images of the part that is being disassembled.
Packard Bell B.V. reserves the right to make changes to the EasyNote ML without notice.
For More Information
For more information about the Packard Bell EasyNote ML, visit Packard Bell‘s support web site at www.packardbell.com
. The support web site also has links to additional
Packard Bell documentation and detailed product specifications.
Technician Notes
Only technicians authorized by Packard Bell B.V. should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. Any indication of component replacement or printed wiring board modifications may void any warranty or exchange allowances.
2
Disassembly
When disassembling the system unit, follow these general rules:
n Turn OFF the power to the system and all peripherals using the power button. n Unplug the AC adapter and all power and signal cables from the system. n Remove any SD/MMC card, ExpressCard or dummy card from the computer. n Do not disassemble the system into parts that are smaller than those specified in
the instructions.
n Label all remov ed connectors; note where th e connector goes and in what position it
was installed.
n The screws for the different components vary in size. During the disassembly
process, group the screws with the corresponding components to avoid mismatch when putting back the components.
Reassembly
Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws are returned to their proper positions. Check that no tools or any loose parts have been left inside the casing. Check that everything is properly installed and tightened .
Required Tools
To disassemble the computer, you need the following tools:
n Wrist grounding strap and conductive mat for preventing electrostatic discharge. n Small Phillips screwdriver. n Small flat screwdriver.
Packard Bell EasyNote ML Disas sembly Manual
3
Hazardous Voltage
There is hazardous voltage present inside the notebook when it is connected to an AC supply, even when the notebook’s power switch is off. Exposure to hazardous voltage could cause personal injury. To avoid risk of injury, contact an Authoriz ed Service Provider for proper (un)installation o f opti onal hardware devices.
Avoid Electrostatic Discharge
Electrostatic electricity can easily damage circuit cards and integrated circuits (ICs). To reduce risk of damage , store them in pr otective packaging whenever they are not installed in the system.
Add-in cards can be extr emely sensiti ve to ESD and always require careful handling. After removing the card from the notebook, place the card flat on a grounded, static-free surface, component-side up. Use a conductive foam pad if available, but not the card wrapper. Do not slide the card over any surface.
Before you install or remove memory modules, video memory, disk drives, circuit cards or other devices, protect them from static electricity. To do so, make sure the notebook’s power switch is OFF. Then, unplug th e notebook’s AC power cord. Before picking up the device you (un)install, you should wear an anti-static wrist wrap (availabl e at electronic supply stores). Be sure to connect the wrist wrap to an unpainted metal portion of the notebook casing. As an alternative, you can dissipa te el ectrostatic bui ld-up by touchi n g an unpainted metal portion of the notebook casing with one hand. Then touch the device you are (un)installing with the other hand, and maintain continuous contact with it until it is (un)installed in the notebook.
WARNING
Ensure that the notebook is disconnected from its power source an d from all telecomm unications lin ks , networks, or modem lines whenever the casing cover is removed. Do not operate the notebook with the cover removed.
AVERTISSEMENT
Assurez-vous que le système est débranché de son alimentation ainsi que de toutes les liaisons de télécomm unication, des réseaux, et des lignes de modem avant d’enlever le capot. Ne pas utiliser le système quand le capot est enlevé.
WARNUNG
Das System darf weder an eine Stromq uelle angeschlossen sein noch eine Verbindung mit einer Telekommunikatio nseinrichtung, einem Netzwerk oder einer Modem-Leitung haben, wenn die Gehäuseabdeckung entfernt wird. Nehmen Sie das System nicht oh ne die Abdeckung in Betr ieb.
ADVERTENCIA
Asegúrese de que cada v ez que se quite la cubierta del portátil, el sistema haya sido desconectado de la red de alimentación y de todos lo enlaces de telecomunicaciones, de red y de líneas de módem. No ponga en funcionamiento el sistema mientras la cubierta esté quitada.
WAARSCHUWING
Zorg er voor dat alle verbindingen van en naar de notebook (stroom, modem, netwerk, etc) verbroken worden voordat de behuizing geopend wordt. Zet de notebook nooit aan als de behuizing geopend is.
Power Supply Unit
Under no circumstances should you attempt to disassemble the power supply. The power supply contains no user-serviceable parts. Inside the power supply are hazardous volt ages that can cause serious personal injury. Always return a defective power supply to the dealer.
Packard Bell EasyNote ML Disas sembly Manual
AVVERTENZA
Prima di rimuovere il coperchio del telaio, assicurarsi che il sistema sia scollegato dall’alimentazione, da tutti i collegamenti di comunicazione, reti o linee di modem. Non avviare il sistema senza aver prima messo a posto il coper chio.
44444
Battery
Perform the following steps to remove the battery:
1. Make sure the power is off.
2. Turn the notebook upside down.
Note:
Use an anti-static mat or something soft like a piece of cloth underneath the notebook to prevent damage to
the exterior of the notebook.
3. Slide both battery latches to the unlock position.
4
Fig. 1 Removing the battery.
4. Take the battery out of the compartment.
Optical Disk Drive
To remove the optical disk drive, first remove the battery (see Battery perform the following steps:
1. Remove the two screws securing the optical disk drive.
on page 4) and then
Fig. 2 Location of the screws securing the optical disk drive.
Packard Bell EasyNote ML Disas sembly Manual
55555
2. Use the emergency eject hole to open the optical disk drive.
3. Pull the tray and take out the optical disk drive from the drive.
Fig. 3 The tray of the optical drive.
Note:
The tray bezel is a delicate part, use care when handling it.
Hard Disk Drives
To remove the hard disk drives, first remove the battery (see Battery on page 4) and th en perform the following steps:
1. Remove the two screws securing the hard disk drive compartment covers.
5
Fig. 4 The hard disk drive compartment cover screws.
2. Li ft the covers upwards.
3. Remove the two screws that keep each hard disk in place.
4. Pull the plastic tab on the hard disk drives to disconnect them.
Fig. 5 Disconnecting and removing the hard disk drives.
Packard Bell EasyNote ML Disas sembly Manual
66666
5. Take the drives out of the compartment.
6. Remove the two screws on the metal brackets to separate them fro m the hard disks drives.
Note:
The drive bays in the compartment are not labelled, so you cannot see which hard disk drive the BIOS
considers the first disk.
Memory
To remove the memory installed, first remove the battery (see Battery on pa ge 4) and then perform the following steps:
1. Remove the two screws securi ng the memory compartment cover.
6
Fig. 6 Removing memory compartment cover.
2. Take away the memory compartment cover.
3. Release the clip on each side securing the memory module; the module will eject
upwards.
Fig. 7 Removing the memory module.
Packard Bell EasyNote ML Disas sembly Manual
77777
4. Carefully remove the memory module from the socket.
Note:
In c ase two memory modules have been installed, you have t o remove the top module first bef ore you can
remove the one underneath.
Wireless LAN Adapter
To remove the wireless LAN adapter, first remove the battery (see Battery on page 4) and then perform the following steps:
7
1. Remove the two screws securing the memory compartment cover (see Fig. 4 page 6).
2. Take away the memory compartment cover.
3. Carefully disconnect the two wireless antenna cables.
4. Remove the two screws holding the wireless LAN adapter.
on
Fig. 8 Location of wireless antenna cable connectors and screws.
5. Take out the wireless LAN adapter from the socket.
Keyboard
To remove the keyboard, first remove the battery (see Battery perform the following steps:
1. Turn the notebook over so the top is facing up and open the LCD completely.
2. Release the keyboard by prying it up along the top side of the keyboard. There are five tabs holding the keyboard in place on the front, particularly at the following keys: <Esc>, <F5>, <F10>, <Pause> and <*>.
Packard Bell EasyNote ML Disas sembly Manual
on page 4) and then
88888
Fig. 9 Removing keyboard.
3. Tilt the keyboard gently forward and let it rest upside down on the touchpad.
4. Carefully release the black clip securing the flat cable.
5. Disconnect the cable from the main board.
8
Fig. 10 Releasing keyboard flat cable.
Top Cover
To remove the top cover, remove the battery (see Battery on page 4) and the keyboard (see Keyboard
1. Remove the two screws under the keyboard.
on page 7), then perform the following steps:
Packard Bell EasyNote ML Disas sembly Manual
99999
Fig. 11 Location of the touchpad connector.
2. Carefully unlock the keyboard cable connector.
3. Pull the cable out of the connector.
9
Fig. 12 Location of the bottom base screws.
4. Turn the notebook over so the top is facing down and remove the 22 screws securing the top cover:
a. Twelve screws on the back panel b. One screw underneath the WLAN panel c. Two screws below the left HDD panel d. Two screws below the right HDD panel e. Five screws inside the battery compartment
Packard Bell EasyNote ML Disas sembly Manual
1010101010
Fig. 13 Location of the top cover screws.
5. Turn the notebook over so the top is facing up.
6. Tilt the screen all the way to allow space for the hinge covers to come loose.
7. Carefully take away the top cover from the base.
10
LCD Panel
To remove the LCD panel, first remove the top cover (see above) and then perform the following steps:
1. Open the WLAN panel and disconnect the two antenna cables.
Fig. 14Disconnecting the wireless antenna cables.
2. Turn the notebook over and remove the screw holding the ground wire.
3. Disconnect the LCD cable from the main board.
4. Remove the two screws in each the top left- and right-hand corner.
5. Take away the LCD panel.
Packard Bell EasyNote ML Disas sembly Manual
1111111111
Fig. 15 LCD hinge screws, LCD cable and grounding cable screw.
Main Board
To remove the main board, perform all of the above disassembly steps, then perform the following steps:
1. Disconnect the five cables from the main board.
11
Fig. 16 Location of left speaker bracket screw.
2. Re move the seven screws holding the main board.
3. Lift the main board out of the bottom base.
Packard Bell EasyNote ML Disas sembly Manual
1212121212
Fig. 17 Location of the main board screws.
Video Board
To remove the video board, first remove the battery (see Main Board perform the following steps:
12
on page 11), then
1. Flip over the main board so you can see the back, which contains the heat sink.
2. Remove the five screws from the elevated video board.
Fig. 18 Location of the video board.
3. Carefully lift the video board out of its socket.
Packard Bell EasyNote ML Disas sembly Manual
1313131313
Heat Sink
To remove the optional Intel Turbo Memory module (mini PCI Express), first remove the video board (see above), and then perform the following steps:
1. Disconnect the CPU fan cable.
2. Remove the four screws securing the heat sink.
3. Remove the three screws securing the CPU fan.
13
Fig. 19 Location of the heat sink.
4. Lift the heat sink assembly from the mainboard.
CPU
To remove the CPU, first remove the heat sink (see above), and then follow these steps:
1. Turn the screw in the CPU into the unlock position to release the CPU.
Fig. 20 Unlocking the CPU.
Packard Bell EasyNote ML Disas sembly Manual
1414141414
LCD Assembly
To disassemble the LCD panel, first remove it (see LCD Panel on page 10) and then perform the following steps:
1. Remove the six rubber stoppers and then remove the screws.
14
Fig. 21 The rubber stoppers and screws.
2. Remove the front cover from the LCD panel.
3. Remove the screws holding the LCD panel to the brackets.
4. Take away the LCD panel.
Packard Bell EasyNote ML Disas sembly Manual
Fig. 22 The brackets screws.
1515151515
15
Webcam
To remove the webcam, first remove the top cover of the LCD panel (see above) and then perform the following steps:
1. Remove both screws and lift out the webcam.
Fig. 23 The webcam screws.
Packard Bell EasyNote ML Disas sembly Manual
1616161616
16
Notice
The information in this gu ide is subj ect to change without notice. This guide contains information protected by copyright. No part of this guide may be
photocopied or reproduced in any form or by any means without prior written consent from Packard Bell B.V.
PACKARD BELL B.V. SHALL NOT BE HELD LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR
OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQU ENTIAL DAMAG ES RESULTING FROM THE FURNISHING, PERFORM AN CE, OR USE OF THIS MATERIAL.
Copyright © 2008 Packard Bell B.V. All rights reserved. Packard Bell is a tradem ark of Packard Bell B.V.
The names of actual companies and products mentioned herein may be trademarks and/or registered trademarks of their respective owners.
The software described in this guide is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of the agreement.
EasyNote ML Dis assembly Manual
Authors: Michael Snijders & Juan M. Calviño First Edition: November 2008 Version: 1.0 Part Number: xxxx
Packard Bell B.V.
www.packardbell.com
Packard Bell EasyNote ML Disas sembly Manual
Loading...