Ozito OZRO450A, DSG-172K Instruction Manual

Motor: 450W
Input: 230V ~ 50Hz
Disc diameter: 125mm (5”)
Paper retention: Hook & loop
No load speed: 0 - 12,000 /min
Weight: 2.3kg

1. Trigger switch 4. Dust bag (not shown)

2. Lock on button 5. Vacuum adaptor

3. Variable speed control 6. Hook & loop backing pad

1

2

3

SPECIFICATIONS - MODEL NO. OZRO450A

1

6

5

KNOW YOUR PRODUCT

2

TABLE OF CONTENTS

Page 1
Page 3
Page 3
Page 4
Page 6
Page 7
Page 10
Page 12
Page 13
Page 14
Page 15

SPECIFICATIONS………………………………………
INTRODUCTION………………………………………..
ELECTRICAL SAFETY………………………………….
GENERAL SAFETY INSTRUCTIONS…………………
RANDOM ORBITAL SANDER SAFETY WARNINGS…
PREPARATION & SETUP………………………………
OPERATION…………………………………………….
MAINTENANCE………………………………………...
DESCRIPTION OF SYMBOLS…………………………
CONTENTS……………………………………………..
WARRANTY……………………………………………..

INTRODUCTION

3

Congratulations on purchasing the Ozito Random Orbital
Sander. We aim to provide quality tools at an affordable price.
We hope you will enjoy using this product for many years.

Your Ozito Random Orbital Sander OZRO450A has been
designed for sanding timber, metal and plastics. It is intended
for DIY use only.

WARNING! When using mains-powered equipment, basic safety
precautions, including the following, should always be followed to
reduce risk of fire, electric shock, personal injury and material damage.

Read and understand the manual prior to operating this tool.
Save these instructions and other documents supplied with this tool for future reference.
The electric motor has been designed for 230V and 240V only. Always check that

the power supply corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for

Australia and New Zealand.

This tool is double insulated in accordance with AS/NZS 3160: 1996;
therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by a qualified electrician or a
power tool repairer in order to avoid a hazard.

If operating a power tool in a damp location is unavoidable use a residual current
device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Note: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury
resulting from a possible electrical insulation failure within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool.
Before use, inspect the extension lead for signs of damage, wear and ageing.
Replace the extension lead if damaged or defective. When using an extension lead
on a reel, always unwind the lead completely. Use of an extension lead not suitable
for the power input of the tool or which is damaged or defective may result in a
risk of fire and electric shock.

ELECTRICAL SAFETY

!

!

!

!

4

GENERAL POWER TOOL SAFETY INSTRUCTIONS

WARNING! Read all safety warnings and all instructions. Failure to

follow the warnings and instructions may result in electric shock, fire and/or
serious injury.

Save all warnings and instructions for future reference.

The term “power tool" in all of the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.

1) Work area safety
a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions

can cause you to lose control.

2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual

current device (RCD) protected supply. Use of an RCD reduces the risk of

electric shock.

3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating

a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alcohol or medication.

A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appr

opriate conditions will r

educe personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power sour

ce and/or battery pack, picking up or carrying the

tool.

Carrying power tools with your finger on the switch or energising power tools

that have the switch on invites accidents.

!

!

!

!