The NCP300 and NCP301 series are second generation ultra−low
current voltage detectors. These devices are specifically designed for
use as reset controllers in portable microprocessor based systems
where extended battery life is paramount.
Each series features a highly accurate undervoltage detector with
hysteresis which prevents erratic system reset operation as the
comparator threshold is crossed.
The NCP300 series consists of complementary output devices that
are available with either an active high or active low reset output. The
NCP301 series has an open drain N−Channel output with either an
active high or active low reset output.
The NCP300 and NCP301 device series are available in the
Thin TSOP−5 package with standard undervoltage thresholds.
Additional thresholds that range from 0.9 V to 4.9 V in 100 mV steps
can be manufactured.
Features
• Quiescent Current of 0.5 A Typical
• High Accuracy Undervoltage Threshold of 2.0%
• Wide Operating Voltage Range of 0.8 V to 10 V
• Complementary or Open Drain Reset Output
• Active Low or Active High Reset Output
• Pb−Free Packages are Available
T ypical Applications
• Microprocessor Reset Controller
• Low Battery Detection
• Power Fail Indicator
• Battery Backup Detection
http://onsemi.com
5
1
THIN SOT23−5/TSOP−5/SC59−5
PIN CONNECTIONS AND
Reset
Output
Input
GND
xxx = Specific Device Code
Y= Year
W= Work Week
See detailed ordering and shipping information in the ordering
information section on page 20 of this data sheet.
ORDERING INFORMATION
SN SUFFIX
CASE 483
MARKING DIAGRAM
1
2
3
(Top View)
xxxYW
5
N.C.
N.C.
4
Complementary Output Configuration
2
Input
NCP300xSNxxT1
*
V
ref
* The representative block diagrams depict active low reset output ‘L’ suffix devices. The comparator
inputs are interchanged for the active high output ‘H’ suffix devices.
Semiconductor Components Industries, LLC, 2004
October, 2004 − Rev. 14
Open Drain Output Configuration
2
Input
1
Reset Output
3
GND
This device contains 25 active transistors.
Figure 1. Representative Block Diagrams
1Publication Order Number:
NCP301xSNxxT1
*
V
ref
1
Reset Output
3
GND
NCP300/D
NCP300, NCP301
Á
Á
Á
Á
Á
Á
Á
Á
MAXIMUM RATINGS
RatingSymbolValueUnit
Input Power Supply Voltage (Pin 2)
Output Voltage (Pin 1)
Complementary, NCP300
ББББББББББББББББ
N−Channel Open Drain, NCP301
Output Current (Pin 1) (Note 2)
Thermal Resistance Junction−to−Air
Operating Junction Temperature Range
Operating Ambient Temperature Range
Storage Temperature Range
Moisture Sensitivity Level (TA = 235°C)
Latchup Performance
Positive
ББББББББББББББББ
Negative
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously . If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL−STD−883, Method 3015.
Machine Model Method 200 V.
2. The maximum package power dissipation limit must not be exceeded.
Maximum Operating Voltage (Pin 2)V
Minimum Operating Voltage (Pin 2)
(T
= −40°C to 85°C)
A
Reset Output Current (Pin 1, Active Low ‘L’ Suffix Devices)
N−Channel Sink Current, NCP300, NCP301
= 0.05V, Vin = 0.70V)
(V
OUT
(V
= 0.50V, Vin = 1.5V)
OUT
P−Channel Source Current, NCP300
= 5.9V, Vin = 8.0V)1.510.5−
(V
OUT
Reset Output Current (Pin 1, Active High ‘H’ Suffix Devices)
N−Channel Sink Current, NCP300, NCP301
(V
= 0.5 V, Vin = 5.0 V)6.311−
OUT
P−Channel Source Current, NCP300
= 0.4 V, Vin = 0.7 V)
(V
OUT
(V
= GND, Vin = 1.5 V)
OUT
Propagation Delay Input to Output (Figure 2)
Complementary Output NCP300 Series
Output Transition, High to Low
Output Transition, Low to High
N−Channel Open Drain NCP301 Series
Output Transition, High to Low
Output Transition, Low to High
V
in(min)
I
OUT
I
OUT
t
pHL
t
pLH
t
pHL
t
pLH
V
DET−
HYS
I
in
ÁÁÁ
in(max)
V
in(min)
I
OUT
I
OUT
t
pHL
t
pLH
t
pHL
t
pLH
−
−
0.01
1.0
0.011
0.525
−
−
−
−
4.606
0.55
0.65
0.05
2.0
0.04
0.6
49
130
49
−
4.70
0.70
0.80
−
−
−
−
−
300
−
300
4.794
0.1410.2350.329V
−
ÁÁ
−
0.34
ÁÁ
0.53
1.0
ÁÁ
1.4
−−10V
−
−
0.01
1.0
0.011
0.525
−
−
−
−
0.55
0.65
0.05
2.0
0.04
0.6
45
130
45
−
0.70
0.80
−
−
−
−
−
300
−
300
V
mA
mA
s
V
A
Á
V
mA
mA
s
http://onsemi.com
6
Input Voltage, Pin 2
V
DET+
NCP300, NCP301
+ 2
0.7
0 V
5 V
Reset Output Voltage, Pin 1
2.5 V
NCP301L
Open Drain
0.5 V
0 V
V
+ 2
DET+
+ 2
Reset Output Voltage, Pin 1
V
DET+
2
0 V
t
pLH
t
pHL
0.1 V
NCP300L
Complementary
NCP300 and NCP301 series are measured with a 10 pF capacitive load. NCP301 has an additional 470 k pull−up resistor connected from the reset output to +5.0 V. The reset output voltage waveforms are shown for the active low ‘L’ devices. The upper
detector threshold, V
The NCP300 and NCP301 series devices are second
generation ultra−low current voltage detectors. Figures 21
and 22 show a timing diagram and a typical application.
Initially consider that input voltage Vin is at a nominal level
and it is greater than the voltage detector upper threshold
(V
), and the reset output (Pin 1) will be in the high state
DET+
for active low devices, or in the low state for active high
devices. If there is a power interruption and Vin becomes
significantly deficient, it will fall below the lower detector
threshold (V
). This sequence of events causes the Reset
DET−
output to be in the low state for active low devices, or in the
V
Input Voltage, Pin 2
Reset Output (Active Low), Pin 1
V
V
V
V
DET
DET−
V
DET
DET−
0 V
in
+
in
+
high state for active high devices. After completion of the
power interruption, Vin will again return to its nominal level
and become greater than the V
. The voltage detector
DET+
has built−in hysteresis to prevent erratic reset operation as
the comparator threshold is crossed.
Although these device series are specifically designed for
use as reset controllers in portable microprocessor based
systems, they offer a cost−effective solution in numerous
applications where precise voltage monitoring is required.
Figure 22 through Figure 29 shows various application
examples.
Reset Output (Active High), Pin 1
V
in
V
+
DET
V
DET−
0 V
Figure 21. Timing Waveforms
http://onsemi.com
15
2 Input
NCP300, NCP301
APPLICATION CIRCUIT INFORMATION
*
V
DD
V
DD
2.85 V
2.70 V
NCP300
Series
GND
3
1
Reset Output
Reset
* Required for
NCP301
Figure 22. Microprocessor Reset Circuit
2 Input
NCP300
LSN27T1
3
GND
Figure 23. Battery Charge Indicator
1
Reset Output
Microprocessor
GND
Vin < 2.7 ON
V
> 2.835 ON
in
To Additional Circuitry
10 V
Active High
Device Thresholds
Active Low
Device Thresholds
1.0 V
The above circuit combines an active high and an active low reset output device to form
a window detector for monitoring battery or power supply voltages. When the input
voltage falls outside of the window established by the upper and lower device
thresholds, the LED will turn on indicating a fault. As the input voltage falls within the
window, increasing from 1.0 V and exceeding the active low device’s hysteresis
threshold, or decreasing from the peak towards 1.0 V and falling below the active high
device’s undervoltage threshold, the LED will turn off. The device thresholds shown can
be used for a single cell lithium−ion battery charge detector.
UV
Fault
OKOK
OV
Fault
OV
Fault
UV
Fault
Input
Figure 24. Window Voltage Detector
2 Input
UV
NCP301
LSN23T1
3
GND
2 Input
OV
NCP301
HSN43T1
GND
3
1
Reset Output
1
Reset Output
V
supply
Fault
Output
http://onsemi.com
16
5.0 V
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
Á
NCP300, NCP301
APPLICATION CIRCUIT INFORMATION
V
supply
Input
2
NCP301
LSN45T1
GND
3
1
Reset Output
3.3 V
Input
2
NCP301
LSN30T1
3
GND
1
Reset Output
Figure 25. Dual Power Supply Undervoltage Supervision
V
DD
R
H
Input
2
R
L
NCP301
NCP301
NCP301
LSN27T1
LSN27T1
LSN27T1
1
Reset Output
Reset
Low state output if either power
supply is below the respective
undervoltage detector threshold
but greater than 1.0 V.
V
DD
Microprocessor
3
GND
Figure 26. Microprocessor Reset Circuit with Additional Hysteresis
Comparator hysteresis can be increased with the addition of
resistor R
do not account for the change of input current I
the comparator threshold. The internal resistance, R
calculated using I
. The hysteresis equations have been simplified and
H
= 0.26 A at 2.6 V.
in
as Vin crosses
in
is simply
in
Vin Decreasing:
R
H
V
th
R
in
1
V
DET
Vin Increasing:
R
H
V
th
Rin R
V
= Vin Increasing − Vin Decreasing
HYS
L
1
V
DET
V
HYS
Vth Decreasing
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
http://onsemi.com
17
(V)
2.70
2.70
2.70
2.70
2.70
2.70
2.70
2.70
2.70
2.70
GND
Test Data
Vth Increasing
(V)
2.84
2.87
ÁÁÁÁ
2.88
ÁÁÁÁ
2.91
2.90
ÁÁÁÁ
2.94
ÁÁÁÁ
2.98
2.70
ÁÁÁÁ
3.04
ÁÁÁÁ
3.15
V
HYS
(V)
0.135
0.17
Á
0.19
Á
0.21
0.20
Á
0.24
Á
0.28
0.27
Á
0.34
Á
0.35
R
()
0
100
Á
100
Á
100
220
Á
220
Á
220
470
Á
470
Á
470
R
H
L
(k)
−
10
6.8
4.3
10
6.8
4.3
10
6.8
4.3
NCP300, NCP301
5.0 V
100 k
Test Data
C
Input
2
82 k
NCP301
NCP301
NCP300
LSN27T1
LSN27T1
HSN27T1
GND
3
1
Reset Output
C (F)f
0.01259021.77
0.1490
1.05222.07
Figure 27. Simple Clock Oscillator
V
supply
This circuit monitors the current at the load. As
Load
V
DD
current flows through the load, a voltage drop with
respect to ground appears across R
V
= I
sense
load
(kHz)IQ (A)
OSC
* R
The following conditions apply:
sense.
21.97
sense
where
R
sense
Input
2
NCP301
NCP301
NCP301
LSN27T1
LSN27T1
LSN09T1
GND
3
If:
I
V
50 k
1
Microcontroller
Load
I
Load
(V
Reset Output
GND
Figure 28. Microcontroller System Load Sensing
DET−/Rsense
DET−+VHYS
)/R
sense
Then:
Reset Output = 0 V
Reset Output = V
DD
http://onsemi.com
18
NCP300, NCP301
2
Input
V
supply
Vin = 1.0 V to 10 V
NCP301
NCP301
NCP301
LSN27T1
LSN27T1
LSN45T1
3
GND
Input
2
NCP301
NCP301
NCP301
LSN27T1
LSN27T1
LSN27T1
GND
3
2
Input
NCP301
NCP301
NCP301
LSN27T1
LSN27T1
LSN18T1
3
GND
1
Reset
Output
1
Reset
Output
1
Reset
Output
A simple voltage monitor can be constructed by connecting several voltage detectors as shown above. Each LED will
sequentially turn on when the respective voltage detector threshold (V
thresholds (V
) that range from 0.9 V to 4.9 V in 100 mV steps can be manufactured.
NOTE: The ordering information lists standard undervoltage thresholds with active low outputs. Additional active low threshold devices,
ranging from 0.9 V to 4.9 V in 100 mV increments and NCP300/NCP301 active high output devices, ranging from 0.9 V to 4.9 V
in 100 mV increments can be manufactured. Contact your ON Semiconductor representative for availability. The electrical
characteristics of these additional devices are shown in Tables 1 through 4.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifi-
NOTE: The ordering information lists standard undervoltage thresholds with active low outputs. Additional active low threshold devices,
ranging from 0.9 V to 4.9 V in 100 mV increments and NCP300/NCP301 active high output devices, ranging from 0.9 V to 4.9 V
in 100 mV increments can be manufactured. Contact your ON Semiconductor representative for availability. The electrical
characteristics of these additional devices are shown in Tables 1 through 4.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifi-
cations Brochure, BRD8011/D.
Open
Drain
Active
Low
Active
High
SEYTSOP−5
SNATSOP−5
SMUTSOP−5
SEPTSOP−5
SEP
(Pb−Free)
(Pb−Free)
(Pb−Free)
3000 / Tape & Reel
7 in. Reel
(Pb−Free)
TSOP−5
(Pb−Free)
†
http://onsemi.com
21
0.05 (0.002)
S
H
D
54
123
L
G
A
NCP300, NCP301
PACKAGE DIMENSIONS
THIN SOT−23−5/TSOP−5/SC59−5
SN SUFFIX
PLASTIC PACKAGE
CASE 483−02
ISSUE C
B
C
SOLDERING FOOTPRINT*
J
K
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. MAXIMUM LEAD THICKNESS INCLUDES
LEAD FINISH THICKNESS. MINIMUM LEAD
THICKNESS IS THE MINIMUM THICKNESS
OF BASE MATERIAL.
4. A AND B DIMENSIONS DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada
Fax: 480−829−7709 or 800−344−3867Toll Free USA/Canada
Email: orderlit@onsemi.com
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Phone: 81−3−5773−3850
http://onsemi.com
22
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
NCP300/D
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.