Onkyo TX-SR505E, TX SR575, TX-SR8550, TX-SR505 User Manual

AV Receiver

TX-SR505

Contents

Introduction ..................................... 2

Connection .................................... 17

TX-SR505E TX-SR8550 TX-SR575

Instruction Manual

Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference.

Turning On & First Time Setup..... 34

Basic Operation

Playing your AV components ....... 40

Listening to the Radio.................. 42

Enjoying the Listening Modes ..... 48

Advanced Operation..................... 55

Troubleshooting ............................ 65

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12.

Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

PORTABLE CART WARNING

S3125A

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons. The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS

OUVRIR

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualiﬁed service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or

water,

D. If the apparatus does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualiﬁed technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a ﬁre or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit.

17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a ﬂue-like gap for warm air to escape.

Precautions

1. Recording Copyright

—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse

—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3. Care

—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the ﬁnish or remove the panel lettering.

4. Power WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230–240 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

Some models have a voltage selector switch for compatibility with power systems around the world. Before you plug in such a model, make sure that the voltage selector is set to the correct voltage for your area. Before you plug in this model, make sure that the voltage selector is set to the correct voltage for your area. If it isn’t, use a small screwdriver to set it as appropriate. For example, if the voltage in your area is 120 volts, set the selector to “120V.” If it’s between 220 and 240 volts, set it to “220-240V.”

ANTENNA

SURROUND BACK

SURROUND

FRONT

DIGITAL IN

ASSIGNABLE

COAXIAL

(DVD)

(CBL/SAT)

OPTICAL

(VCR/DVR)

(CD)

REMOTE CONTROL

OUT

CBL/SAT IN

VCR/DVR IN

DVD IN

COMPONENT VIDEO

OUT

IN IN

TAPE

B/PB

CR/PR

FMAM75

CBL/SAT

VCR/DVR

DVD

OUT

IN IN

FRONT

INININ

OUT

VOLTAGE

CBL/SAT

VCR/DVR

SELECTOR

MONITOR

OUT

SURROUND

CENTER

SUB WOOFER

DVD

SPEAKERS

120V

SURR BACK

220-240V

CENTER

SPEAKERS

SPEAKERS A

SPEAKER

120V

VOLTAGE

PRE OUT

SELECTOR

SUB

WOOFER

220-240V

FRONT

SPEAKERS B

Pressing the [STANDBY/ON] button to select Standby mode does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Never Touch this Unit with Wet Hands

—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

6. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case.

• This unit’s top and rear panels may get warm after prolonged use. This is normal.

• If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE:

COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION:

MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

THIS CLASS B DIGITAL APPARATUS

TO PREVENT ELECTRIC SHOCK,

Modèle pour les Canadien

REMARQUE:

LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA. Sur les modèles dont la ﬁche est polarisée:

ATTENTION:

TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

CET APPAREIL NUMÉRIQUE DE

POUR ÉVITER LES CHOCS ÉLEC-

Precautions

—Continued

Supplied Accessories

For British models

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualiﬁed service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral Brown: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IMPORTANT

The plug is ﬁtted with an appropriate fuse. If the fuse needs to be replaced, the replacement fuse must approved by ASTA or BSI to BS1362 and have the same ampere rating as that indicated on the plug. Check for the ASTA mark or the BSI mark on the body of the fuse. If the power cord’s plug is not suitable for your socket outlets, cut it off and ﬁt a suitable plug. Fit a suitable fuse in the plug.

Make sure you have the following accessories:

Remote controller and two batteries (AA/R6)

Indoor FM antenna

AM loop antenna

Speaker setup microphone

For European Models

Declaration of Conformity

We,

ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY

declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3.

GROEBENZELL, GERMANY

K. MIYAGI

ONKYO EUROPE ELECTRONICS GmbH

TX-SR575 incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Speaker terminal tool

Power-plug adapter

Only supplied in certain countries. Use this adapter if your AC outlet does not match with the plug on the AV receiver’s power cord. (Adapter varies from country to country.)

Left

Front

Right

Zone 2

Surround

SP-B

Zone 2

Front

Left

Front

Right

SP-B

Left

SP-B

Right

Surround

Front

Left

Front

Right

SP-B

Left

SP-B

Right

Speaker Cable

Left

Right

Surround

Right

Left

Surround

Right

Surround

Left

Right

Center

Zone 2

Surround Back

Zone 2

Right

Zone 2

Left

Center

Zone 2

Right

Zone 2

Left

Surround Back

Right

Surround Back

Left

Center

Surround Back

Right

Surround Back

Left

Speaker cable labels

* In catalogs and on packaging, the letter at the end of the

product name indicates the color. Speciﬁcations and operation are the same regardless of color.

Features

Ampliﬁer

• 7-channel ampliﬁer

• 75 watts per channel rms into 8 ohms, 2 channels driven, 20 Hz to 20 kHz, less than 0.08% total harmonic distortion (FTC rating)

• WRAT (Wide Range Ampliﬁer Technology)

• Optimum Gain Volume Circuitry

• Audyssey 2EQ room correction

Processing

• Dolby*2 Digital EX and Dolby Pro Logic IIx

• DTS, DTS-ES Matrix/Discrete, DTS Neo:6, and DTS

96/24

• Theater-Dimensional*4 virtual surround sound

• Linear PCM 192 kHz/24-bit D/A converters on all channels

• Pure Audio listening mode (not North American model)

•Powerful and highly accurate 32-bit DSP processing

Audio/Video

• Adjustable crossover (40, 50, 60, 80, 100, 120, 150, 200 Hz)

• HDTV-capable component video (3 inputs, 1 output)

•3 S-Video inputs, 2 outputs

•4 assignable digital inputs (2 optical, 2 coaxial)

• Subwoofer pre out

• Color-coded 7.1 multichannel input for use with Super Audio CD and DVD-Audio

• A/B speaker drive

• Color-coded speaker terminal posts

Tuner

• 40 radio presets

• AM/FM auto tuning

• RDS (Radio Data System) (Europe only)

Remote Controller

• Preprogrammed for use with other AV components

TX-SR505 North American model/ TX-SR505E Only

TX-SR575 Only

•2 HDMI*5 inputs, 1 output

• Composite video and S-Video to component video conversion

• Composite video to S-Video and S-Video to composite video conversion

• Neural Surround

•XM*7 Satellite Radio (North American models only)

*XM Passport System required; sold separately.

• SIRIUS*8 Satellite Radio (North American models only)

Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending. Audyssey 2EQ is a trademark of Audyssey Laboratories.

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are registered trademarks of Dolby Laboratories.

“DTS” and “DTS-ES | Neo: 6” are registered trademarks of DTS, Inc. “96/24” is a trademark of DTS, Inc.

Theater-Dimensional is a trademark of Onkyo Corporation.

HDMI, the HDMI logo and High Deﬁnition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC. This unit incorporates HDMI technology.

Neural Surround name and related logos are trademarks owned by Neural Audio Corporation.

(North American models only)

•2 HDMI*5 inputs, 1 output

©2005 SIRIUS Satellite Radio Inc. “SIRIUS,” the SIRIUS dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc. Available only in the contiguous United States (excluding Alaska and Hawaii) and Canada.

is a registered trademark of XM Satellite

Enjoying Home Theater

Speaker Sets A and B

You can use two sets of speakers with the AV receiver:

Speaker set A

*While speaker set B is on, speaker set A is reduced to 5.1-channel playback.

Speaker set B

*Only analog input sources are output by speaker set B.

Speaker set A Speaker set B Indicator Output

should be used in your main listening room for up to 7.1-channel playback.

can be used in another room and offers 2-channel stereo playback.

TUNING

PRESET

SPEAKERS

SETUP ENTER

SETUP MIC

TUNING MODE

CLEAR

A B

Off

STANDBY/ON

STANDBY

MULTI CH C

PHONES

ABSPEAKERS

AUXCBL/SATVCR/DVR

DVD

TONE DISPLAYSTEREO DIMMER MEMORY

LISTENING MODE

TUNERTAPE

DIGITAL INPUT

Off Set A: 7.1 channels

On Set B: 2 channels

Off No sound

RETURN

VIDEO

speaker set A

MASTER VOLUME

AUX INPUT

AUDIOLR

Set A: 5.1 channels Set B: 2 channels

and

speaker set B

DISC

VOL

INPUT

GUIDE

TOP MENU

SP A / B

PLAYLIST/CAT PLAYLIST/CAT

SETUP RETURN

ALBUM

ENTER

VOL

MUTING

Main Room (speaker set A)

Center speaker

Front left

speaker

Subwoofer

Surround

left

speaker

Surround back

left speaker

* While speaker set B is on, the surround

back speakers output no sound.

Surround back

right speaker

Front right

speaker

Sub Room (speaker set B)

Surround

right

speaker

* Digital input sources are not output

by speaker set B. Connect your source component with an analog connection.

Introduction

Important Safety Instructions ....................2

Precautions .................................................3

Supplied Accessories.................................4

Features .......................................................5

Enjoying Home Theater..............................6

Speaker Sets A and B ................................... 6

Getting to Know the AV Receiver..............8

Remote Controller.....................................12

Connection

Connecting Your Speakers ......................17

Connecting Antennas...............................20

Connecting Your Components ................22

About AV Connections ................................22

Connecting Audio and Video Signals

to the AV Receiver .................................... 23

Which Connections Should I Use?..............23

TV or Projector DVD player

Components with HDMI

(TX-SR505 North American Model/

TX-SR505E/TX-SR575 Only) ...................27

VCR or DVD Recorder for Playback ...........28

VCR or DVD Recorder for Recording.......... 29

Camcorder, Games Console,

or Other Device.........................................29

Satellite, Cable, Set-top box,

or Other Video Source ..............................30

CD Player or Turntable................................31

RI Dock........................................................32

Cassette, CDR, MiniDisc,

or DAT Recorder.......................................32

Onkyo Components

Connecting the Power Cord ........................33

..........................................24

.................................................25

.............................33

Turning On & First Time Setup

Turning On the AV Receiver ....................34

First Time Setup........................................35

Automatic Speaker Setup

(Audyssey 2EQ)........................................ 35

Video Input Setup

(TX-SR505 North American Model/

TX-SR505E/TX-SR575 Only) ...................38

Digital Audio Input Setup.............................39

Changing the Input Display .........................39

Basic Operation

Playing Your AV Components ................ 40

Basic AV Receiver Operation ..................... 40

Using the Multichannel DVD Input.............. 41

Displaying Source Information.................... 41

Listening to the Radio.............................. 42

Listening to AM/FM Stations....................... 42

Presetting AM/FM Stations ......................... 43

Using RDS (European Models Only) .......... 44

Common Functions.................................. 46

Setting the Display Brightness.................... 46

Adjusting the Bass and Treble.................... 46

Muting the AV Receiver .............................. 46

Using the Sleep Timer ................................ 47

Using Headphones ..................................... 47

Adjusting Speaker Levels ........................... 47

Enjoying the Listening Modes

Using the Listening Modes...................... 48

Selecting Listening Modes.......................... 48

About the Listening Modes ......................... 50

Using the Late Night Function

(Dolby Digital only) ................................... 52

Using the CinemaFILTER........................... 52

Using the Audio Adjust Settings ................. 52

Advanced Operation

Recording.................................................. 55

Advanced Setup ....................................... 56

Advanced Speaker Settings ....................... 56

Digital Input Signal Formats ....................... 61

Correcting Sound and Picture Sync ........... 61

Controlling Other Components............... 62

Entering Remote Control Codes................. 62

Remote Control Codes for Onkyo

Components Connected via .............. 63

Resetting REMOTE MODE Buttons ........... 63

Resetting the Remote Controller ................ 63

Troubleshooting ....................................... 65

If you can’t resolve an issue, try resetting the AV receiver by holding down the [VCR/DVR] button and pressing the [STANDBY/ON] button.

Specifications ........................................... 69

Getting to Know the AV Receiver

Front Panel

North American Model

STANDBY/ON

STANDBY

3 5 6 74

TUNING

MASTER VOLUME

PRESET

MULTI CH C D

PHONES

ABSPEAKERS

DVD

TONE DISPLAYSTEREO DIMMER MEMORY

Other Models

STANDBY/ON

STANDBY

PURE AUDIO

DVDMULTI CHPURE AUDIO C D

PHONES

ABSPEAKERS

TONE

For detailed information, see the pages in parentheses.

STANDBY/ON button (34)

Sets the AV receiver to On or Standby.

STANDBY indicator (34)

Lights up when the AV receiver is on Standby and ﬂashes while a signal is being received from the remote controller.

Remote-control sensor (16)

Receives control signals from the remote controller.

Display

See “Display” on page 9.

Input selector buttons (40)

Select the input sources. The [MULTI CH] button selects the multichannel

DVD input.

AUXCBL/SATVCR/DVR

LISTENING MODE

AUXCBL/SATVCR/DVR

LISTENING MODE

TUNERTAPE

DIGITAL INPUT

TUNING MODE

CLEAR

SETUP ENTER

SETUP MIC

RETURN

AUX INPUT

VIDEO

AUDIOLR

UJKLMNOPQ8 9RTS

MASTER VOLUME

TUNING

PRESET

TUNERTAPE

DISPLAYSTEREO RT/PTY/TP MEMORY

DIGITAL INPUT

Arrow/TUNING/PRESET and ENTER buttons

TUNING MODE

CLEAR

(European model only)

When the tuner is selected, the TUNING [ ] [ ] buttons are used for radio tuning, and the PRESET

[] [ ] buttons are used to select radio presets (see page 43). With the setup menus, they work as arrow buttons and are used to select and set items. The ENTER button is also used with the setup menus.

MASTER VOLUME control (40)

Sets the volume of the AV receiver to MIN, 1 through 79, or MAX.

PHONES jack (47)

This 1/4-inch phone jack is for connecting a standard pair of stereo headphones for private listening.

SPEAKERS A and B buttons (6, 40)

Turn speaker sets A and B on or off.

SETUP ENTER

SETUP MIC

RETURN

AUX INPUT

VIDEO

AUDIOLR

Getting to Know the AV Receiver

—Continued

TONE, [–], and [+] buttons (46)

Used to adjust the bass and treble.

STEREO button (48)

Selects the Stereo listening mode.

LISTENING MODE [ ]/[ ] buttons (48)

Select the listening modes.

DISPLAY button (41)

Displays various information about the currently selected input source.

DIGITAL INPUT button (39, 61)

Used to assign the digital inputs and to specify the format of digital input signals.

DIMMER or RT/PTY/TP button (45, 46)

Adjusts the display brightness. On the European model, this is the RT/PTY/TP but-

ton, and it’s used with RDS (Radio Data System). See “Using RDS (European Models Only)” on page 44.

MEMORY button (43)

Used when storing or deleting radio presets.

TUNING MODE button (42)

Selects the Auto or Manual tuning mode for AM and FM radio.

SETUP button

Used to access the setup menus.

SETUP MIC (36)

The automatic speaker setup microphone connects here.

RETURN button

Selects the previously displayed setup menu.

AUX INPUT (29, 55)

Used to connect a camcorder, games console, and so on. There are jacks for composite video and analog audio.

PURE AUDIO button and indicator (48)

The North American model doesn’t have this button and indicator.

Selects the Pure Audio listening mode. The indicator lights up when this mode is selected.

Display

213 5

For detailed information, see the pages in parentheses.

A and B speaker indicators (6, 40)

Indicator A lights up when speaker set A is on. Indicator B lights up when speaker set B is on.

MUTING indicator (46)

Flashes while the AV receiver is muted.

Input signal format indicators

Show the audio signal format of the current input source.

Listening mode indicators (50)

Show the selected listening mode.

Radio indicators

FM STEREO (42):

reo FM station.

Lights up when tuned to a ste-

RDS (European models only) (44):

when tuned to a radio station that supports RDS (Radio Data System).

AUTO (42):

Auto Tuning mode is selected, and disappears when Manual Tuning mode is selected.

TUNED (42):

tion.

SLEEP indicator (47)

Lights up when the Sleep function has been set.

Message area

Displays various information about the selected input source.

Audyssey indicator (35)

Lights up during automatic speaker setup.

For AM and FM radio, lights up when

Lights up when tuned to a radio sta-

Lights up

Getting to Know the AV Receiver

—Continued

Rear Panel

TX-SR505 other than North American model/TX-SR8550

1 4 53

6 9

DIGITAL IN

ASSIGNABLE

COAXIAL

(DVD)

(CBL/SAT)

OPTICAL

(VCR/DVR)

(CD)

REMOTE CONTROL

B/PB

CR/PR

CBL/SAT IN

COMPONENT VIDEO

OUT

VCR/DVR IN

DVD IN

OUT

IN IN IN

TAPE

ANTENNA

FMAM75

CBL/SAT

VCR/DVR

OUT

IN IN

OUT

CBL/SAT

VCR/DVR

FRONT

SURROUND BACK

SPEAKERS

MONITOR

DVD

OUT

SURROUND

CENTER

SUB

WOOFER

DVD

SURR BACK

SURROUND

SPEAKERS

PRE OUT

SUB

WOOFER

FRONT

SPEAKERS A

J K L M N O Q

TX-SR505 North American model/TX-SR505E

1 2 53 6

HDMI

ASSIGNABLE

OUT

DIGITAL IN

ASSIGNABLE

COAXIAL

(DVD)

(CBL/SAT)

OPTICAL

(VCR/DVR)

(CD)

REMOTE CONTROL

IN 1IN 2

B/PB

CR/PR

VCR/DVR IN

DVD IN

IN IN

OUT

TAPE

CBL/SAT IN

COMPONENT VIDEO

CBL/SAT

ANTENNA

FMAM75

VCR/DVR

DVD

OUT

IN IN

OUT

VCR/DVR

FRONT

MONITOR

OUT

SURROUND

DVD

SURROUND BACK

CENTER

SUB

WOOFER

SPEAKERS

SURR BACK

SURROUND

SPEAKERS

PRE OUT

SUB

WOOFER

FRONT

SPEAKERS A

FRONT

SPEAKERS B

FRONT

SPEAKERS B

CENTER

SPEAKER

120V

VOLTAGE SELECTOR

220-240V

(Only some models)

CENTER

SPEAKER

J K L M N O

TX-SR575

1 2 53 6

HDMI

ASSIGNABLE

OUT

DIGITAL IN

ASSIGNABLE

COAXIAL

(DVD)

(CBL/SAT)

OPTICAL

(VCR/DVR)

(CD)

REMOTE CONTROL

IN 1IN 2

B/PB

CR/PR

IN 3

COMPONENT VIDEO

OUT

IN 2 IN 1(DVD)

ASSIGNABLE

OUT

IN IN IN

TAPE

CBL/SAT

ANTENNA

FMAM75

VCR/DVR

DVD

OUT

IN IN

FRONT

OUT

VCR/DVR

(North American model only)

7 8

SIRIUS

MONITOR

OUT

SURROUND BACK

SPEAKERS

SURROUND

SURR BACK

CENTER

SUB

WOOFER

DVD

J K L M N O

SURROUND SPEAKERS

PRE OUT

SUB

WOOFER

FRONT

SPEAKERS A

SPEAKERS B

FRONT

CENTER

SPEAKER

Getting to Know the AV Receiver

—Continued

DIGITAL IN OPTICAL 1, 2 and COAXIAL 1, 2

These optical and coaxial digital audio inputs are for connecting components with optical or coaxial digital audio outputs, such as CD and DVD players.

HDMI IN 1, 2, and OUT (TX-SR505 North

American model/TX-SR505E/ TX-SR575 only)

These jacks are for connecting HDMI-compatible components. Audio and video signals received by the HDMI IN jacks pass through to the HDMI OUT jack.

COMPONENT VIDEO

A DVD player, TV, or other component that supports component video can be connected here.

AM ANTENNA

These push terminals are for connecting an AM antenna.

FM ANTENNA

This jack is for connecting an FM antenna.

MONITOR OUT

The S-Video or composite video output should be connected to a video input on your TV or projector.

SIRIUS antenna (TX-SR575 North American model only)

This jack is for connecting a SIRIUS Satellite Radio antenna (see the separate SIRIUS instructions).

XM antenna (TX-SR575 North American model only)

This jack is for connecting an XM Passport System, sold separately (see the separate XM instructions).

FRONT SPEAKERS A, SURROUND

SPEAKERS, CENTER SPEAKER, and SURROUND BACK SPEAKERS

These terminal posts are for connecting speaker set A.

REMOTE CONTROL

This Remote Interactive jack can be connected to the jack on another -capable Onkyo component. To use , you must make an analog audio

connection (RCA) between the AV receiver and the other component, even if they are connected digitally.

CD IN

This analog audio input is for connecting a CD player’s analog audio output.

TAPE IN/OUT

This analog audio input and output are for connecting a recorder with an analog audio input and output, such as a cassette deck, MD recorder, etc.

VCR/DVR IN/OUT and CBL/SAT IN

The VCR/DVR inputs and outputs can be used to connect a VCR or DVR (digital video recorder).

The CBL/SAT inputs can be used to connect a cable/satellite receiver, set-top box, etc.

DVD IN

These jacks can be used to connect a DVD player with an analog multichannel audio output for SACD and DVD-Audio playback.

SUBWOOFER PRE OUT

A powered subwoofer can be connected here.

FRONT SPEAKERS B

These push terminals are for connecting speaker set B.

VOLTAGE SELECTOR (Only some models)

This voltage selector provides compatibility with power systems around the world (see page 3).

See pages 17–33 for hookup information.

Remote Controller

Using the Remote Controller

Including the AV receiver, the remote controller can be used to control up to seven different components. The remote controller has a speciﬁc operating mode for use with each type of component. Modes are selected by using the six REMOTE MODE buttons.

■

RECEIVER/TAPE Mode

In RECEIVER/TAPE mode, you can control the AV receiver and an Onkyo cassette recorder connected via .

■

DVD and CD/MD/CDR/DOCK Modes

With these modes, you can control a DVD player and CD player, MD recorder, CDR, or RI dock. By entering the appropriate remote control code, you can control Onkyo components or components made by other manufacturers (see page 62).

■

TV, VCR and SAT/CABLE Modes

With these modes, you can control a TV, VCR, and satellite or cable receiver. You must enter the appropriate remote control code ﬁrst (see page 62).

REMOTE MODE

RECEIVER

TAPE/AMP

Press one of the REMOTE MODE buttons to select a mode.

DVD

M D/CDR

DOCK

VCR

CABLE

SAT

Use the buttons supported by that mode to control the component.

RECEIVER/TAPE mode:

see right column

DVD mode:

see page 14

CD/MD/CDR/DOCK mode:

see page 15

TV, VCR, SAT/CABLE modes:

see page 64

RECEIVER

TAPE/AMP

DVD

M D/CDR

DOCK

VCR

CABLE

SAT

RECEIVER/TAPE Mode

RECEIVER/TAPE mode is used to control the AV receiver. It can also be used to control an Onkyo cassette recorder connected via .

RECEIVER

TAPE/AMP

STANDBY/ON

INPUT SELECTOR

123

VCR/DVR

456

AUX

789

10 11 12

D TUN

--/---

INPUT

GUIDE

TOP MENU

SP A / B

PLAYLIST/CAT PLAYLIST/CAT

SETUP RETURN

CBL/SAT

MULTI CH

DIMMER

VOL

REMOTE MODE

RECEIVER

TAPE/AMP

DVD

ENT

SLEEP

ALBUM

ENTER

C DTAPE TUNER

CLR

DISC

DVD

D/CDR

C D

DOCK

VCR

CABLE

SAT

VOL

MUTING

LISTENING MODE

SURROUND

Buttons or TAPE input is selected.

STEREO

SUBTITLE

AUDIO REPEAT

TEST TONE

PLAY MODE

DISPLAY

1, 2, 3

, and 4 are used when the TUNER

CH SEL

RANDOM

681M

LEVEL

L NIGHT

LEVEL

CINE FLTR

HDDDVDVCR

P Q

Note:

Some of the remote controller operations described in this manual may not work as expected with other components.

Remote Controller

—Continued

For detailed information, see the pages in parentheses.

STANDBY/ON button (34)

Sets the AV receiver to On or Standby.

INPUT SELECTOR buttons (40)

Used to select the input sources.

MULTI CH button (41)

Selects the multichannel DVD input.

DIMMER button (46)

Adjusts the display brightness.

SP A/B button (6, 40)

Used to turn speaker sets A and B on or off.

Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons

Used to select and adjust settings.

SETUP button

Used to access the setup menus.

LISTENING MODE buttons (48)

Used to select the listening modes. These buttons work in all remote controller modes.

STEREO button

Selects the Stereo listening mode.

SURROUND button

Selects the Dolby and DTS listening modes and the Neural Surround listening mode (TX-SR575 North American model only).

[ ]/[ ] buttons

Used to select the available listening modes.

TEST TONE, CH SEL, LEVEL-, and LEVEL+ buttons (47, 59)

Used to adjust the level of each speaker.

DISPLAY button (41)

Displays various information about the selected input source.

REMOTE MODE buttons (12)

Used to select the remote controller modes. When a remote controller button is pressed, the REMOTE MODE button for the currently selected mode lights up.

SLEEP button (47)

Used with the Sleep function.

VOL [ ]/[ ] button (40)

Adjusts the volume of the AV receiver regardless of the currently selected remote controller mode.

MUTING button (46)

Mutes or unmutes the AV receiver.

RETURN button

Selects the previously displayed setup menu.

CINE FLTR button (52)

Used with the CinemaFILTER function.

L NIGHT button (52)

Used with the Late Night function.

■

Buttons used when the TUNER input is selected

To select the Tuner (AM/FM) as the input source, press:

RECEIVER

Number, D TUN, and ENT buttons (43)

Used to select AM and FM radio stations directly.

CH +/– button (43)

Used to select radio presets.

Arrow [ ]/[ ] buttons

For AM and FM, the Up and Down [ ]/[ ] buttons are used for tuning.

■

Buttons used when the TAPE input is selected

To select your Cassette deck as the input source, press:

RECEIVER

Playback buttons

On twin cassette decks, only deck B can be controlled.

Play [ ] button

Starts playback.

Stop [ ] button

Stops playback.

Reverse Play [ ] button

Starts reverse playback.

Rewind and FF [ ]/[ ] buttons

The Rewind [ ] button starts rewind. The FF [] button starts fast forward.

TUNER

TAPE

Remote Controller

—Continued

DVD Mode

By default, the remote controller is set to control an Onkyo DVD player.

To select your DVD player as the input source, press:

DVD

REMOTE MODE

RECEIVER

TAPE/AMP

DVD

ENT

SLEEP

ALBUM

ENTER

C DTAPE TUNER

CLR

DISC

DVD

D/CDR

C D

DOCK

VCR

CABLE

SAT

VOL

MUTING

MULTI CH

DVD

RECEIVER

STANDBY/ON

INPUT SELECTOR

123

CBL/SAT

CR/DVR

456

AUX

MULTI CH

789

10 11 12

D TUN

--/---

DIMMER

VOL

INPUT

GUIDE

TOP MENU

SP A / B

PLAYLIST/CAT PLAYLIST/CAT

SETUP RETURN

LISTENING MODE

SURROUND

8 9

STEREO

RANDOM

SUBTITLE

AUDIO REPEAT

TEST TONE

CH SEL

PLAY MODE

DISPLAY

LEVEL

L NIGHT

LEVEL

CINE FLTR

HDDDVDVCR

N O

681M

STANDBY/ON button

Sets the DVD player to On or Standby.

Number buttons

Used to enter title, chapter, and track numbers and times for locating speciﬁc points.

DISC +/– button

Selects discs on a DVD changer.

TOP MENU button

Selects a DVD’s top menu.

Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons

Used to navigate DVD menus and the DVD player’s onscreen setup menus.

SETUP button

Used to access the DVD player’s onscreen setup menus.

Playback buttons

From left to right: Pause, Play, Stop, Fast Reverse, Fast Forward, Previous, and Next.

SUBTITLE button

Selects subtitles.

AUDIO button

Selects foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS).

DISPLAY button

Displays information about the current disc, title, chapter, or track, including elapsed time, remaining time, total time, and so on.

CLR button

Cancels functions and clears entered numbers.

MENU button

Displays a DVD’s menu.

RETURN button

Exits the DVD player’s onscreen setup menus.

RANDOM button

Used with the random playback function.

REPEAT button

Used with the repeat playback functions.

VCR, DVD, and HDD buttons

Used to select VCR, HDD (hard disk drive), or DVD playback on a VCR/DVD recorder with a built-in hard disk drive.

PLAY MODE button

Selects play modes on components with selectable play modes.

Remote Controller

—Continued

CD/MD/CDR/DOCK Mode

By default, the remote controller is set to control an Onkyo CD player.

To select the input source, press:

C D

RECEIVER

TAPE

* If you’re using an MD, CDR, or an RI Dock, you must

change the Input Display (see page 39).

STANDBY/ON

INPUT SELECTOR

4 5

123

CBL/SAT

CR/DVR

456

AUX

MULTI CH

789

10 11 12

D TUN

--/---

DIMMER

VOL

INPUT

GUIDE

TOP MENU

SP A / B

PLAYLIST/CAT PLAYLIST/CAT

SETUP RETURN

CD player

MD or CD recorder

RI Dock

CBL/SAT

REMOTE MODE

RECEIVER

TAPE/AMP

DVD

C DTAPE TUNER

CLR

ENT

SLEEP

DISC

ALBUM

ENTER

DVD

D/CDR

C D

DOCK

VCR

CABLE

SAT

VOL

MUTING

M D/CDR

C D

DOCK

LISTENING MODE

SURROUND

STEREO

RANDOM

SUBTITLE

AUDIO REPEAT

TEST TONE

CH SEL

PLAY MODE

DISPLAY

LEVEL

L NIGHT

LEVEL

CINE FLTR

HDDDVDVCR

K L

STANDBY/ON button

Sets the component to On or Standby.

Number buttons

Used to enter track numbers and times for locating speciﬁc points on CD/MD players.

DISC/ALBUM +/– button

Selects discs on a CD changer, or the next or previous album on an HDD-compatible component connected to an RI Dock.

TOP MENU button

Works as a Mode button when used with a DS-A2 RI Dock.

Arrow [ ]/[ ] and ENTER buttons

Used to navigate menus on an HDD-compatible component connected to an RI Dock.

Playback buttons

From left to right: Pause, Play, Stop, Fast Reverse, Fast Forward, Previous and Next.

DISPLAY button

Displays information about the current disc or track on a CD player or MD/CD recorder, including elapsed time, remaining time, total time, and so on. On an HDD-compatible component connected to an RI Dock, it turns on the back light for 30 seconds.

CLR button

Cancels functions and clears entered numbers on a CD player or MD/CD recorder.

MENU button

Used to navigate menus on an HDD-compatible component connected to an RI Dock.

PLAYLIST [ ]/[ ] buttons

Selects the previous or next playlist on an HDDcompatible component connected to an RI Dock.

RANDOM button

Used with the random/shufﬂe playback function.

REPEAT button

Used with the repeat playback functions.

PLAY MODE button

Used to select play modes on components with selectable play modes. Works as a Resume button when used with a DS-A2 RI Dock.

681M

Remote Controller

—Continued

Installing the Batteries

To open the battery compartment, press

the small hollow and slide open the cover.

Insert the two supplied batteries (AA/R6)

in accordance with the polarity diagram inside the battery compartment.

Slide the cover shut.

Notes:

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion.

Aiming the Remote Controller

When using the remote controller, point it toward the AV receiver’s remote control sensor, as shown below.

Remote control sensor

AV receiver

STANDBY indicator

Approx. 16 ft. (5 m)

Notes:

• The remote controller may not work reliably if the AV receiver is subjected to bright light, such as direct sunlight or inverter-type ﬂuorescent lights. Keep this in mind when installing.

• If another remote controller of the same type is used in the same room, or the AV receiver is installed close to equipment that uses infrared rays, the remote controller may not work reliably.

• Don’t put anything on top of the remote controller, such as a book or magazine, because a button may be pressed continuously, thereby draining the batteries.

• The remote controller may not work reliably if the AV receiver is installed in a rack behind colored glass doors. Keep this in mind when installing.

• The remote controller will not work if there’s an obstacle between it and the AV receiver’s remote control sensor.

Connecting Your Speakers

Enjoying Home Theater

Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. You can enjoy DVDs featuring DTS and Dolby Digital. With analog and digital TV, you can enjoy Dolby Pro Logic IIx and Onkyo’s own DSP surround listening modes.

Front left and right speakers

These output the overall sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equally spaced from the TV. Angle them inward slightly so as to create a triangle, with the listener at the apex.

Center speaker

This speaker enhances the front left and right speakers, making sound movements distinct and providing a full sound image. For movies it’s used mainly for dialog.

Position it close to your TV facing forward at about ear level, or at the same height as the front left and right speakers.

Subwoofer

The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) channel. The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listening position. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at one-third the way along the wall, as shown.

Tip: To ﬁnd the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results.

Corner

1/3 wall length

Surround back left and right speakers

These speakers are necessary to enjoy Dolby Digital EX, DTS-ES Matrix, DTS-ES Discrete. They enhance the realism of surround sound and improve sound localization behind the listener. Position them behind the listener about 2–3 feet (60–100 cm) above ear level.

* While speaker set B is on,

these speakers output no sound.

Surround left and right speakers

These speakers are used for precise sound positioning and to add realistic ambience.

Position them at the sides of the listener, or slightly behind, about 2–3 feet (60–100 cm) above ear level. Ideally they should be equally spaced from the listener.

Speaker Conﬁguration

For the best surround-sound experience, you should connect seven speakers and a powered subwoofer. The following table shows which channels you should use based on the number of speakers that you have.

Number of speakers: 234567

Front left

Front right

Center

Surround left

Surround right

Surround back

Surround back left

Surround back right

✓✓✓✓✓✓

✓ ✓✓✓

✓✓✓✓

✓

If you’re using only one surround back speaker, connect it to the left (L) SURROUND BACK SPEAKERS terminals.

No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass.

Before using the AV receiver, you must do the automatic speaker setup (see page 35).

Connecting Your Speakers

—Continued

Speaker Connection Precautions

Read the following before connecting your speakers:

•

North American models:

with an impedance of between 6 and 16 ohms. If you use speakers with a lower impedance, and use the ampliﬁer at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

•

Other models:

impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, be sure to set the minimum speaker impedance to “4 ohms” (see page 35). If you use speakers with a lower impedance, and use the ampliﬁer at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

•Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals to only positive (+) terminals, and negative (–) terminals to only negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long or very thin speaker cables may affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires. Doing so may damage the AV receiver.

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver.

• Don’t connect a speaker to several terminals.

You can connect speakers with an

You can connect speakers

Attaching the Speaker Labels

The AV receiver’s positive (+) speaker terminals are color-coded for ease of identiﬁcation. (The negative (–) speaker terminals are all black.)

Speaker terminal Color

Front left White

Front right Red

Center Green

Surround left Blue

Surround right Gray

Surround back left Brown

Surround back right Tan

The supplied speaker labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the above table. All you need to do then is to match the color of each label to the corresponding speaker terminal.

Using the Speaker Terminal Tool

The supplied speaker terminal tool makes it easy to tighten and loosen the speaker terminals. If you are using banana plugs, to ensure optimum sound quality, tighten the speaker terminal before inserting the banana plug. (In Europe, using banana plugs to connect speakers to an audio ampliﬁer is prohibited.)

Connecting Your Speakers

—Continued

Connecting Speaker Set A

Strip 5/8" (15 mm) of insu-

lation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

Unscrew the terminal. Fully insert the bare wire,

making sure that it’s touching the threaded shaft in the center. Screw the terminal tight.

5/8" (15 mm)

Connecting a Powered Subwoofer

Using a suitable cable, connect the AV receiver’s SUBWOOFER PRE OUT to the input on your powered subwoofer. If your subwoofer is unpowered and you’re using an external ampliﬁer, connect the SUBWOOFER PRE OUT to it’s input.

Note:

Make sure the plugs are pushed in all the way.

Connecting Speaker Set B

Strip 3/8" (10 mm) of insu-

lation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

While pressing the lever, insert

the wire into the hole, and then release the lever.

Make sure that the terminals are gripping the bare wires, not the insulation.

Note:

While speaker set B is on, speaker set A is reduced to

5.1-channel playback.

Speaker Set A

Front right

speaker

3/8" (10 mm)

Front left

speaker

The following illustration shows which speaker should be connected to each pair of terminals.

If you’re using only one surround back speaker, connect it to the left (L) SURROUND BACK SPEAKERS terminals.

ANTENNA

CBL/SAT

VCR/DVR

OUT

INININ

OUT

CBL/SAT

VCR/DVR

Front right

speaker

SURROUND BACK

SPEAKERS

FMAM75

MONITOR

DVD

OUT

IN IN

FRONT

SURROUND

SURR BACK

CENTER

SUB

WOOFER

DVD

Speaker Set B

SURROUND SPEAKERS

PRE OUT

SUB

WOOFER

Front left

speaker

FRONT

SPEAKERS A

FRONT

SPEAKERS B

CENTER

SPEAKER

LINE INPUT

Powered

subwoofer

SURROUND BACK

SPEAKERS

Surround

back right

speaker

SURROUND SPEAKERS

Surround

back left

speaker

Center

speaker

FRONT

SPEAKERS A

CENTER

SPEAKER

Surround

right

speaker

Surround

left

speaker

Connecting Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.

The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

AM antenna push terminals FM antenna jack

OUT

ANTENNA

FMAM75

OUT

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

Attach the FM antenna, as shown.

■

American Model

FM 75

Insert the plug fully into the jack.

Connecting the AM Loop Antenna

The supplied indoor AM loop antenna is for indoor use only.

Assemble the AM loop antenna, inserting

the tabs into the base, as shown.

Connect both wires of the AM loop

antenna to the AM push terminals, as shown.

(The antenna’s wires are not polarity sensitive, so they can be connected either way around).

Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.

Push Insert wire Release

■

Other Models

FM 75

Insert the plug fully into the jack.

Once your AV receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.

Use thumbtacks or something similar to

ﬁx the FM antenna into position.

Thumbtacks, etc.

Caution:

Be careful that you don’t injure yourself

when using thumbtacks.

Once your AV receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.

Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna (see page 21).

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead (see page 21).

Connecting Antennas

—Continued

Connecting an Outdoor FM Antenna

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

FM 75

Notes:

• Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft.

•For best results, install the outdoor FM antenna well away from tall buildings, preferably with a clear line of sight to your local FM transmitter.

• Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc.

•For safety reasons, outdoor antenna should be situated well away from power lines and other high-voltage equipment.

• Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

■

Using a TV/FM Antenna Splitter

It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown.

Connecting an Outdoor AM Antenna

If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.

Outdoor antenna

Insulated antenna cable

AM loop antenna

Outdoor AM antennas work best when installed horizontally outside, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected.

Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.

TV/FM antenna splitter

To AV receiver To TV (or VCR)

Connecting Your Components

About AV Connections

• Before making any AV connections, read the manuals supplied with your other AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

Optical Digital Jacks

The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.

Caution:

plug straight when inserting and removing.

AV Cables and Jacks

To prevent shutter damage, hold the optical

Video

Cable Jack Description

Component video cable

S-Video cable

Composite video cable

AV Connection Color Coding

RCA-type AV connections are usually color coded: red, white, and yellow. Use red plugs to connect right-channel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and outputs (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.

Left (white)

Right (red)

(Yellow)

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

•To prevent interference, keep audio and video cables away from power cords and speaker cables.

Component video separates the luminance (Y) and

color difference signals (PR, PB), providing the best

B/PB

picture quality. (Some TV manufacturers label their component video jacks slightly differently.)

CR/PR

S-Video separates the luminance and color signals

and provides better picture quality than composite video.

Composite video is commonly used on TVs, VCRs,

and other video equipment. Use only dedicated composite video cables.

Analog audio

Composite video

Left (white)

Right (red)

(Yellow)

Right!

Wrong!

Audio

Cable Jack Description

Optical digital audio cable

Coaxial digital audio cable

Analog audio cable (RCA)

Multichannel analog audio cable (RCA)

Note:

The AV receiver does not support SCART connections.

OPTICAL

COAXIAL

This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for coaxial.

This offers the best sound quality and allows you to enjoy Dolby Digital and DTS. The audio quality is the same as for optical.

This cable carries analog audio. It’s the most common connection format for analog audio and can be found on virtually all AV components.

This cable carries multichannel analog audio and is typically used to connect DVD players with a 7.1channel analog audio output. Several standard analog audio cables can be used instead of a multichannel cable.

+ 50 hidden pages