Onkyo TX-SR393 operation manual

AV RECEIVER

TX-SR393

Instruction Manual

Table of contents ≫

Connections ≫

- Connecting Speakers ≫

Playback ≫

Setup ≫

Troubleshooting ≫

Appendix ≫

Supplementary Information ≫

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

≫

What’s in the box 4 Additional Function (Firmware Update) 5

Update Information of the rmware 5 Operation of added new functions 5 Firmware Update Procedure 6

Part Names 8

Front Panel 8 Display 10 Rear Panel 11 Remote Controller 13

Connections

Connecting speakers 15

Speaker Installation 16

Speaker Connections and "Speaker Setup" Settings 21

Speaker combinations 25

Connecting the TV 26

To ARC TV 27 To Non-ARC TV 28

Connecting Playback Devices 29

Connecting an AV Component with HDMI Jack Mounted 29

Connecting an AV Component in a Separate Room (ZONE B Connection) 31

Connecting a Pre-main Amplier (ZONE B) 31

Connecting Antennas 32 Connecting the Power Cord 33

Playback

AV Component Playback 35

Basic Operations 35

BLUETOOTH® Playback 36

Basic Operations 36

Listening To the AM/FM Radio 37

Tuning into a Radio Station 37 Presetting a Radio Station 39

Using RDS (European, Australian and Asian models) 41

ZONE B Playback 42

Playing Back 42

Convenience functions 44

Adjusting the tone 44 Sleep Timer 45

Listening Mode 46

Selecting a Listening mode 46

Connecting an Audio Component 30

Speaker Layouts and Selectable Listening Modes 48 Listening Mode E󰀨ects 50

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

Input Formats and Selectable Listening Modes 54

Setup

Setup Menu 61

Menu list 61 Menu operations 63

1. Input/Output Assign 64

2. Speaker 67

3. Audio Adjust 70

4. Source 71

5. Hardware 73

6. Miscellaneous 76

Quick Menu 77

Menu operations 77

Initial Setup with Auto Start-up Wizard 79

≫

Operations 79

Troubleshooting

When the unit is operating erratically 82 Troubleshooting 83

Appendix

About HDMI 89

General Specications 91

Front Panel≫ Rear Panel≫ Remote≫

What’s in the box

Contents ≫ Connections ≫ Playback ≫ Setup

1. Main unit (1)

2. Remote controller (RC-970R) (1), Batteries (AAA/R03) (2)

3. Speaker setup microphone (1)

• Used during Initial Setup.

4. Indoor FM antenna (1)

5. AM loop antenna (1)

• Quick Start Guide (1) * This document is an online instruction manual. It is not included as an

accessory.

• Connect speakers with an impedance of 4 Ω to 16 Ω.

• The power cord must be connected only after all other connections are

completed.

• We will not accept any responsibility for damage arising from the connection

with equipment manufactured by other companies.

• Specications and appearance are subject to change without prior notice.

≫

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

Additional Function (Firmware Update)

This unit is equipped with a function to update the rmware via USB port when the rmware update is announced after purchase. This enables various functions to be added and operations to be improved. Depending on the manufacturing timing of the product, the rmware may be switched to the updated one. In such a case, new functions may be added from the start. For how to conrm the latest rmware contents and the rmware version of your product, see the following section.

Update Information of the rmware

For the latest rmware contents and the rmware version, visit our company’s website. If the rmware version of your product di󰀨ers from the latest one, it is recommended to update the rmware. To conrm the rmware version of your product, press the button on the remote controller, and refer to "6. Miscellaneous" - "Firmware Update" - "Version" ( p76).

Operation of added new functions

If functions are added or changed from contents described in the Instruction Manual, see the following reference.

Supplementary Information ≫

≫

❏ Firmware Update Procedure ( p6)

Front Panel≫ Rear Panel≫ Remote≫

Firmware Update Procedure

Contents ≫ Connections ≫ Playback ≫ Setup

≫

Approx. 30 minutes are required for updating. Existing settings are kept after

updating.

Disclaimer: The program and accompanying online documentation are furnished

to you for use at your own risk. Our company will not be liable and you will have no remedy for damages for any claim of any kind whatsoever concerning your use of the program or the accompanying online documentation, regardless of legal theory, and whether

arising in tort or contract.

In no event will our company be liable to you or any third party for any special, indirect, incidental, or consequential damages of any kind, including, but not limited to, compensation, reimbursement or damages on account of the loss of present or prospective prots, loss of data, or for any other reason whatsoever.

Updating the Firmware via USB

• While updating the rmware, do not do the following: – Disconnecting and reconnecting cables, USB storage device, speaker

setup microphone or headphones, or performing operations on the unit such as turning the power o󰀨

• Prepare a 128 MB or larger USB storage device. The format of USB storage

devices supports FAT16 or FAT32 le system format.

– Media inserted into a USB card reader may not be used for this function. – USB storage devices equipped with the security function are not supported. – USB hubs and USB devices equipped with the hub function are not

supported. Do not connect these devices to the unit.

• Delete any data stored on the USB storage device.

• If "HDMI CEC" is set to "On", set it to "O󰀨". – Press . Next, select "5. Hardware" - "HDMI" and press ENTER, then

select "HDMI CEC" and select "O󰀨".

* Depending on the USB storage device or its content, long time may be required

for loading, the content may not be loaded correctly, or power may not be supplied

correctly.

* Our company will not be liable whatsoever for any loss or damage of data, or storage

failure arising from the use of the USB storage device. Please note this in advance.

* The descriptions may di󰀨er from the actual on-screen displays, however, operations

and functions are the same.

Update

1. Connect the USB storage device to your PC.

2. Download the rmware le from the our company's website to your PC and unzip.

Firmware les are named as below.

ONKAVR_.zip

Unzip the le on your PC. The number of unzipped les and folders varies

depending on the model.

3. Copy all unzipped les and folders to the root folder of the USB storage

device.

• Make sure to copy the unzipped les.

4. Connect the USB storage device to the POWER OUT port of this unit.

• If an AC adapter is supplied with the USB storage device, connect the AC adapter, and use it with a household outlet.

• If the USB storage device has been partitioned, each section will be treated as an independent device.

5. Press .

The Setup menu is displayed on the TV screen.

Setup

1. Input/Output Assign

2. Speaker

3. Audio Adjust

4. Source

5. Hardware

6. Miscellaneous

1. TV Out / OSD

2. HDMI Input

3. Digital Audio Input

4. Analog Audio Input

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

≫

6. Select "6. Miscellaneous" - "Firmware Update" - "Update via USB" with the cursors in order, then press ENTER.

Setup

1. Input/Output Assign

2. Speaker

3. Audio Adjust

4. Source

5. Hardware

6. Miscellaneous

1. Tuner

2. Firmware Update

3. Initial Setup

4. Lock

• If "Firmware Update" is grayed out and cannot be selected, wait for a while until it starts up.

7. Press ENTER with "Update" selected, and start update.

• During the update, the TV screen may go black depending on the program

to be updated. In such a case, check the progress on the display of the unit. The TV screen will remain black until the update is completed and the power is turned on again.

• During the update, do not turn the power o󰀨, or disconnect or reconnect the USB storage device.

• When "Completed!" is displayed, the update is complete.

8. Disconnect the USB storage device from the unit.

9. Press ON/STANDBY on the main unit to turn the unit into standby mode.

The process is completed, and your rmware is updated to the latest version.

• Do not use on the remote controller.

If an Error Message is Displayed

If an error occurs, "Error! -" is displayed on the display of the unit. ("" represents an alphanumeric character.) Refer to the following descriptions and

check.

Error Code

• -70:

The USB storage device cannot be recognized, the rmware le is not present in the root folder of the USB storage device, or the rmware le is for another model. Check if the USB storage device or USB cable is securely inserted to the POWER OUT port of the unit.

Connect the USB storage device to an external power source if it has its own power supply.

• -51: The rmware le is for another model, or the rmware le is corrupted. Retry from the download of the rmware le.

• Others:

After removing the power plug once, insert it to the outlet, and then start the

operation from the beginning.

Front Panel≫ Rear Panel≫ Remote≫

Part Names

Front Panel

Contents ≫ Connections ≫ Playback ≫ Setup

≫

❏ For details, see ( p9)

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

1. ON/STANDBY button

2. MUSIC OPTIMIZER button: Turns on/o󰀨 the MUSIC OPTIMIZER function that

improves the quality of the compressed audio.

3. BLUETOOTH indicator: Lights up when this unit and a BLUETOOTH-enabled device are connected.

4. DOLBY ATMOS indicator: Lights up when Dolby Atmos signals are reproduced

in appropriate listening mode.

5. Remote control sensor: Receives signals from the remote controller.

• The reception range of the remote controller is within a distance of approx. 16´/5 m, and an angle of 20° in vertical direction and 30° to right and left.

6. ZONE A/B button: Selects an audio output destination from among "ZONE A",

"ZONE B" and "ZONE A+B". ( p42)

INFO button: Switches the information on the display and is used to operate RDS ( p41).

8. DIMMER button: Switches the brightness of the display with three levels. It cannot be turned o󰀨 completely.

9. Display ( p10)

10.

SETUP button: You can display advanced setting items on the TV and the display to have a more enjoyable experience with this unit. ( p61)

11.

Cursor buttons ( / / / ) and ENTER button: Select an item with the cursors, and press ENTER to conrm your selection. When using TUNER, use them to tune in to stations. ( p37)

12.

RETURN button: Returns the display to the previous state while setting.

13.

MASTER VOLUME

14.

PHONES jack: Connect headphones with a standard plug (ø1/4"/6.3 mm).

15.

LISTENING MODE button: Switches the listening mode ( p46) by pressing "STEREO", "MOVIE/TV" and "MUSIC" repeatedly.

16.

Input selector buttons: Switches the input to be played.

17.

TONE CONTROL button: Adjusts the sound quality. Press / of "TREBLE", "VOCAL" or "BASS" respectively. ( p44)

18.

SETUP MIC jack: Connect the supplied speaker setup microphone. ( p80)

≫

Front Panel≫ Rear Panel≫ Remote≫

Display

Contents ≫ Connections ≫ Playback ≫ Setup

≫

1. Speaker/Channel display: Displays the output channel that corresponds to the selected listening mode.

2. Displays the audio output destination.

A: Outputs audio only to the main room (ZONE A). B: Outputs audio only to the separate room (ZONE B). AB: Outputs audio to both the main room (ZONE A) and separate room (ZONE B).

3. Lights in the following conditions.

: Headphones are connected.

: Connected by BLUETOOTH.

HDMI: HDMI signals are input and the HDMI input is selected. DIGITAL: Digital signals are input and the digital input is selected.

4. Lights according to the type of input digital audio signal and the listening mode.

5. Lights in the following conditions. RDS (European, Australian and Asian models): Receiving RDS broadcasting. TUNED: Receiving AM/FM radio. FM ST: Receiving FM stereo. SLEEP: Sleep timer is set. ( p75) AUTO STBY: Auto Standby is set. ( p75)

6. Blinks when muting is on.

7. Displays various information of the input signals.

654

Front Panel≫ Rear Panel≫ Remote≫

Rear Panel

Contents ≫ Connections ≫ Playback ≫ Setup

≫

❏ For details, see ( p12)

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

1. HDMI OUT jacks: Transmit video signals and audio signals with an HDMI cable connected to a TV.

2. HDMI IN jacks: Transmit video signals and audio signals with an HDMI cable connected to an AV component.

3. POWER OUT port: The power (5 V/1 A) can be supplied to a streaming media player, etc. using a USB cable. ( p29) The playback function is not supported.

4. Power cord

5. DIGITAL IN OPTICAL/COAXIAL jacks: Input TV or AV component digital audio signals with a digital optical cable or digital coaxial cable.

6. TUNER AM/FM terminal: Connect the supplied antennas.

7. AUDIO IN jacks: Input TV or AV component audio signals with an analog audio cable.

8. ZONE B LINE OUT jacks: Output audio signals with an analog audio cable

connected to a pre-main amplier in a separate room (ZONE B).

9. SUBWOOFER PRE OUT jacks: Connect a powered subwoofer with a subwoofer cable. Up to two powered subwoofers can be connected. The same signal is output from each SUBWOOFER PRE OUT jack.

10.

SPEAKERS terminals: Connect speakers with speaker cables. (FRONT L/R terminals of North American models support banana plugs.)

≫

Front Panel≫ Rear Panel≫ Remote≫

Remote Controller





 







   

 

 

 



  

Contents ≫ Connections ≫ Playback ≫ Setup

1. ON/STANDBY button

2. Input selector buttons: Switches the input to be played.

3. Play buttons:

is switched to "CEC MODE" using the MODE button, an HDMI CEC function-enabled AV component can be operated. (Depending on the device, operation may not be possible.)

4. Q (QUICK MENU) button: such as "HDMI" and "Audio" quickly on the TV screen while playing.

5. Cursor buttons and ENTER button: Select an item with the cursors, and press ENTER to conrm your selection.

6. button: Display advanced setting items on the TV or the display to have a more enjoyable experience with this unit. ( p61)

7. TONE button: Adjusts the sound quality. ( p44)

8. LISTENING MODE button: Select a listening mode ( p46).

9. DIMMER button: Switches the brightness of the display with three levels. It

cannot be turned o󰀨 completely.

10.

CLEAR button: Deletes all characters you have entered when entering text on

the TV screen.

11.

MEMORY button: Used to register AM/FM radio stations. ( p39)

12.

SLEEP button: Set the sleep timer. Select the time from "30 min", "60 min" and "90 min". ( p45)

13.

ZONE A/B button: Selects an audio output destination from among "ZONE A", "ZONE B" and "ZONE A+B". ( p42)

14.

Input selector cursors: Switches the input to be played.

15.

button: Switches the information on the display and is used to operate RDS

( p41).

16.

button: Returns the display to the previous state while setting.

17.

button: Temporarily mutes audio. Press the button again to cancel muting.

18.

VOLUME buttons

19.

AUDIO SEL button: When a device is connected to two or more audio input terminals for one input selector, you can select which audio input signal to play.

20.

M.OPT button: Turns on/o󰀨 the MUSIC OPTIMIZER function that improves the quality of the compressed audio.

21.

MODE button: Switches between automatic tuning and manual tuning for AM/FM stations ( p37). Also, when an HDMI CEC function-enabled AV component is connected to this unit, you can switch "3. Play buttons" between "CEC MODE" and "RCV MODE" (normal mode).

Used for playback operation of a BLUETOOTH-enabled device. If the unit

Pressing this button during playback can make settings

( p77)

≫

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

Connections

Connecting speakers 15 Connecting the TV 26 Connecting Playback Devices 29 Connecting an AV Component in a Separate Room

(ZONE B Connection) 31 Connecting Antennas 32 Connecting the Power Cord 33

≫

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

Connecting speakers

You can select the layout of speakers to be installed from various patterns when using this unit. Use the following ow chart to select the speaker layout that suits your speakers and usage environment. You can check the connection method and default settings.

Use height speakers?

Yes No

• 3.1.2 Channel System ( p24) • 5.1 Channel System ( p23)

≫

Front Panel≫ Rear Panel≫ Remote≫

Speaker Installation

Contents ≫ Connections ≫ Playback ≫ Setup

≫

 5.1 Channel System

a: 22° to 30°, b: 120°

This is a basic 5.1 Channel System. Front speakers output the front stereo sound, and a center speaker outputs the sound of the center of the screen, such as dialogs and vocals. Surround speakers create the back sound eld. Powered subwoofer reproduces the bass sound, and creates the rich sound eld. The front speakers should be positioned at ear height while the surround speakers should be positioned just above ear height. The center speaker should be set up facing the listening position at an angle. Placing the powered

subwoofer between the center speaker and the front speaker gives you a natural sound even when playing music sources.

1,2 Front Speakers

3 Center Speaker

4,5 Surround Speakers 6 Powered Subwoofer

❏ Speaker Layouts and Selectable Listening

Modes ( p48)

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

 3.1.2 Channel System

A 3.1.2 Channel System is a speaker layout consisting of a 3.1 Channel System that includes front speakers, center speaker and powered subwoofer, and added height speakers. Select the height speakers that suit your speakers and usage environment from the following three types.

❏ Front High Speakers Installation Example

( p18)

❏ Ceiling Speakers Installation Example

( p19)

❏ Dolby Enabled Speakers (Dolby Speakers)

Installation Example ( p20)

≫

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

≫

❏ Front High Speakers Installation Example

3´ (0.9 m) or more

a: 22° to 30°

This is a 3.1-channel system consisting of front speakers, a center speaker, and a powered subwoofer, with the addition of front high speakers, a type of height speaker. Installing the height speakers will enrich the sound eld feeling in the upper space. Front high speakers should be situated at least 3'/0.9 m higher than

the front speakers.

They should also be put directly above the front speakers, angled to face the

listening position.

1,2 Front Speakers

3 Center Speaker

4,5 Front High Speakers 6 Powered Subwoofer

❏ Speaker Layouts and Selectable Listening

Modes ( p48)

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

≫

❏ Ceiling Speakers Installation Example

a: 65° to 100°

This is a 3.1-channel system consisting of front speakers, a center speaker, and a powered subwoofer, with the addition of top middle speakers, a type of height speaker. Installing the height speakers will enrich the sound eld feeling in the upper space. Fit top middle speakers on the ceiling directly above the listening position. The distance between each pair should match the distance between the two front speakers.

• Dolby Laboratories recommends the setups of these types of height speakers

to obtain the best Dolby Atmos e󰀨ect.

1,2 Front Speakers

3 Center Speaker

4,5 Top Middle Speakers 6 Powered Subwoofer

❏ Speaker Layouts and Selectable Listening

Modes ( p48)

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

≫

❏ Dolby Enabled Speakers (Dolby Speakers)

Installation Example

a: 22° to 30°

This is a 3.1-channel system consisting of front speakers, a center speaker, and a powered subwoofer, with the addition of Dolby enabled speakers (front), a type

of height speaker. Dolby enabled speakers are special speakers designed to face

the ceiling, so that the sound is heard from overhead by bouncing the sound o󰀨 the ceiling. Installing the height speakers will enrich the sound eld feeling in the

upper space.

Place Dolby enabled speakers (front) above the front speakers.

1,2 Front Speakers

3 Center Speaker

4,5 Dolby Enabled Speakers (Front) 6 Powered Subwoofer

❏ Speaker Layouts and Selectable Listening

Modes ( p48)

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

1/2˝

(12 mm)

Speaker Connections and "Speaker Setup" Settings

Connections

 (Note) Speaker Impedance

Connect speakers with an impedance of 4 Ω to 16 Ω. If any of the speakers to be connected has an impedance of 4 Ω or more and less than 6 Ω, set "Speaker Impedance" to "4 ohms" for "Speaker Setup" in the Initial Setup section ( p79). When setting "Speaker Impedance" from the Setup menu, press on the remote controller, and set "2. Speaker" - "Conguration" - "Speaker Impedance" ( p67) to "4 ohms".

 Connect the Speaker Cables

≫

Make correct connection between the unit's jacks and speaker's jacks (+ side to + side, and - side to - side) for each channel. If the connection is wrong, a bass sound will not be reproduced properly due to reverse phase. Twist the wires exposed from the tip of the speaker cable so that the wires do not stick out of the speaker terminal when connecting. If the exposed wires touch the rear panel, or the + side and - side wires touch each other, a malfunction may occur.

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

 Connect the Subwoofer

a Subwoofer cable

Connect a powered subwoofer with this unit using a subwoofer cable. Up to two powered subwoofers can be connected. The same signal is output from each SUBWOOFER PRE OUT jack.

≫

Front Panel≫ Rear Panel≫ Remote≫

 5.1 Channel System

Contents ≫ Connections ≫ Playback ≫ Setup

 "Speaker Setup" settings during

Initial Setup ( p80)

Speaker Setup

Speaker Channels

Subwoofer

Speaker Impedance

5.1 ch

6 ohms or above

Yes

- - -Height Speaker

≫

This is a basic 5.1 Channel System. For details of the speaker layout, refer to "Speaker Installation" ( p16).

Front Panel≫ Rear Panel≫ Remote≫

Select how many speakers you have.

ENTER

• Speaker Channels: 5.1 ch

• Subwoofer: Yes

• Height Speaker: ---

• Speaker Impedance: Set any

value ( p21)

 3.1.2 Channel System

Contents ≫ Connections ≫ Playback ≫ Setup

≫

This is a combination of the 3.1 Channel System and front high speakers. A front high speaker is a type of height speaker.

You can select only one set of height speakers from the following three types for connection.

❏ Front High Speakers Installation Example ( p18) ❏ Ceiling Speakers Installation Example ( p19) ❏ Dolby Enabled Speakers (Dolby Speakers) Installation Example ( p20)

 "Speaker Setup" settings during

Initial Setup ( p80)

Speaker Setup

Speaker Channels

Subwoofer

Speaker Impedance

Select how many speakers you have.

• Speaker Channels: 3.1.2 ch

• Subwoofer: Yes

• Height Speaker: Select the

type of height speaker actually installed.

• Speaker Impedance: Set any

value ( p21)

3.1.2 ch

Front HighHeight Speaker

6 ohms or above

Yes

ENTER

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

Speaker combinations

• Up to two powered subwoofers can be connected in either combination.

Speaker Channels FRONT CENTER SURROUND HEIGHT

2.1 ch

3.1 ch

4.1 ch

5.1 ch

2.1.2 ch

3.1.2 ch

≫

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

Connecting the TV

Connect this unit between a TV and AV component. Connecting this unit with the TV can output the video and audio signals of the AV component to the TV, or play the audio of the TV on this unit. Connection with the TV di󰀨ers depending on whether the TV supports the ARC (Audio Return Channel) function or not. The ARC function transmits the audio signals of the TV via an HDMI cable, and plays the audio of the TV on this unit. To check if the TV supports the ARC function, refer to the instruction manual of the TV, etc.

Does your TV support the ARC function?

Yes No

• To ARC TV ( p27) • To Non-ARC TV ( p28)

≫

Front Panel≫ Rear Panel≫ Remote≫

To ARC TV

Contents ≫ Connections ≫ Playback ≫ Setup

If the TV supports the ARC (Audio Return Channel) function (*), use only the HDMI cable to connect with the TV. Use the ARC-compatible HDMI IN jack of the

TV for connection.

Setup

• Settings are required to use the ARC function. Select "Yes" for "3. ARC Setup"

in Initial Setup ( p79). If "No, Skip" is selected, settings are required in the Setup menu after Initial Setup is completed. Press on the remote controller, and set "5. Hardware" - "HDMI" - "Audio Return Channel" to "On". ( p74)

• For detailed settings for TV connection, CEC function and audio output, refer to the instruction manual of the TV.

(*) ARC function: This function transmits the audio signals of the TV via an HDMI cable, and plays the audio of the TV on this unit. Connection to an ARCcompatible TV is complete with one HDMI cable. To check if the TV supports the ARC function, refer to the instruction manual of the TV, etc.

≫

a HDMI cable

Front Panel≫ Rear Panel≫ Remote≫

To Non-ARC TV

Contents ≫ Connections ≫ Playback ≫ Setup

If the TV does not support the ARC (Audio Return Channel) function (*), connect

an HDMI cable and digital optical cable.

• If you use a cable set-top box, etc. connected to the input jack of this unit to

watch TV (without using a TV’s built-in tuner), connection with a digital optical cable or analog audio cable is not required.

≫

a HDMI cable, b Digital optical cable

Front Panel≫ Rear Panel≫ Remote≫

Contents ≫ Connections ≫ Playback ≫ Setup

Connecting Playback Devices

Connecting an AV Component with HDMI Jack Mounted

This is a connection example of an AV component equipped with an HDMI jack. When connecting with an AV component that conforms to the CEC (Consumer Electronics Control) standard, you can use the HDMI CEC function (*) that enables linking with input selectors, etc. and the HDMI Standby Through function that can transmit video and audio signals of the AV component to the TV even if this unit is in standby mode. Also, the POWER OUT port on the rear panel can supply power (5 V/1 A) to a streaming media player, etc. using a USB cable. To supply power even when this unit is in standby mode, change the setting value of "USB Power Out at Standby" ( p75) to "On".

• To play 4K or 1080p video, use a high speed HDMI cable.

Setup

• The HDMI CEC function and HDMI Standby Through function are

Streaming media

player

BD/DVD Cable/Satellite

GAME

set-top box

automatically enabled if you select "Yes" for "3. ARC Setup" in Initial Setup ( p79). If "No, Skip" is selected, settings are required in the Setup menu after Initial Setup is completed. Press on the remote controller, and select "5. Hardware" - "HDMI" to make the settings. ( p73)

• To enjoy digital surround sound including Dolby Digital, set the audio output of the connected Blu-ray Disc player etc. to the Bitstream output.

(*)The HDMI CEC function: This function enables various linking operations with CEC-compliant devices, such as switching input selectors interlocking with a CEC-compliant player, switching audio output between TV and this unit or adjusting the volume using the remote controller of a CEC-compliant TV, and automatically switching this unit to standby when the TV is turned o󰀨.

≫

a HDMI cable

Front Panel≫ Rear Panel≫ Remote≫

+ 65 hidden pages